Lightolier IS:1062LV User's Manual
Contents
1. ECTOR TRIMS VOIDS THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD NOTE 1 LOW VOLTAGE FIXTURES should be dimmed only by special dimmers intended specifically for that purpose Use Lightolier Scenist Crescendo VA Neptune VA Precision VA Easyset VA Sunrise VA Radiant VA or equivalent products by others or variable autotransformers or electronic dimmers intended for use with low voltage fixtures 2 Low voltage fixtures may produce audible sound when used with dimmers which may be objectionable in acoustically critical areas LAMP BY OTHERS SOCKET LAMP LAMP SPRING GLASS LAMP GUARD BAFFLE APERTURE TRANSFORMER PRIMARY 120V 60 Hz SECONDARY 11 4V 65W LOAD2. READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE INSTRUCTION SHEET NO This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical f S z 1 062 LV inspector before installation To prevent electrical shock tum off electricity at fuse box before proceeding a Retain these instructions for maintenance reference 0192 Page 1 of 2 INSTRUCTIONS FOR INSTALLATION OF REFLECTOR TRIM 1062LV IN THE 1000LV FRAME IN KIT Fig D 1 FRAME IN 2 CLOSE IN 3 SNAP ON 4 PUSH UP WARNING BEFORE INSTALLING REFLECTOR TRIM FRAME IN KIT READ MARKINGS IN REFLECTOR TRIM AND ON SOCKET CUP OF FRAME IN KIT TO DETERMINE LAMP WATTAGE AND TYPE APPLICABLE FOR YOUR INSTALLATION IF I C TYPE FRAME IN KIT FRAM IN KIT MOUNTS IS USED IT MAY BE INSTALLED IN DIRECT CONTACT WITH ee are ia INSULATED CEILING IF A NONI C TYPE FRAME N KIT IS USED DO Pre Oe NOT INSTALL INSULATION WITHIN 3 INCHES OF FIXTURE SIDES OR es WIRING COMPARTMENT NOR ABOVE FIXTURE IN SUCH A MANNER Seu CEILING TO ENTRAP HEAT ROTO CLIP SEN MATERIAL 1 FRAME IN Fig A vo See Frame In Instruction Sheet for installation procedure 2 ROTATE ROTO CLIPS Fig B As shown in Fig E 3 SNAP ON Fig C Insert SOCKET through RECTANGLE HOLE on top of REFLECTOR TRIM Engage TAB from SOCKET CUP into one of the SLOTS on top of REFLECTOR TRIM and push other
3. end of SOCKET CUP with LANCING into the other Fig F 4 PUSH UP Fig D r Pdi Push REFLECTOR TRIM into ceiling until flange is flush to ceiling Fig D NOTE Socket manufacturers have suggested that socket may fail after 3 to 6 relampings If this occurs socket can be replaced by disconnect ing male connectors attached to socket leads and female connectors attached to fixture leads and replacing it with a new socket procured through LIGHTOLIER Fig G INSULATING SLEEVING MALE CONNECTORS ATTACHED TO SOCKET WIRE FEMALE CONNECTORS ATTACHED TO FIXTURE WIRES MR16 SOCKET C J SCOR OCOC IE y MM 6 e SEE BACK PAGE FOR LAMPING INSTRUCTIONS BCS IT CO 1 IIE IR srontneat auesec canava INSTRUCTION SHEET NO IS 1062LV 0192 Page 2 of 2 LAMPING 1 Check to see that power is OFF before lamping or relamping 2 Remove baffle aperture from ELBOW by pulling straight out Fig H 3 Insert lamp MR 16 bulb between lamp springs 4 Attach SOCKET to bi pin prongs on LAMP 5 Insert LAMP RING with LAMP and GLASS LAMP GUARD back into ELBOW WARNING A LAMP MANUFACTURERS REQUIRE THE GLASS LAMP GUARD BE IN PLACE BEFORE ENERGIZING LAMP AND THAT GREAT CARE MUST BE TAKEN THAT LAMP IS FULLY COOLED BEFORE RELAMPING AVOID FINGER MARKS ON INSIDE OF LAMP FOR THEY MAY CAUSE SHORT LAMP LIFE AND POSSIBLE BREAKAGE B USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER INC USE OF OTHER MANUFACTURER S REFL
Download Pdf Manuals
Related Search