Life Fitness 95Ri User's Manual
Contents
1. Yak TIR DUR Recumbent Exercise Hikes ASSEMBLY INSTRUCTIONS Congratulations and vvelcome to the vvorld of LASCFITRESS The following Parts Identification Listing and the step by step assembly procedures have been assembled to make the set up of the Recumbent Exercise Bikes as quick and easy as possible Please take special note of the following important points prior to choosing a location and beginning assembly of the Recumbent Exercise Bikes IMPORTANT SAFETY INSTRUCTIONSI DO NOT locate the Recumbent Exercise Bike outdoors near swimming pools or in areas of high humidity DO NOT operate your Recumbent Exercise Bike if it has been dropped damaged or even partially immersed in water Contact Life Fitness Customer Support Services at the number in the Operation Manual DO NOT locate the Recumbent Exercise Bike any closer than 30 inches 76 cm to a television set DO NOT locate additional Recumbent Exercise Bike any closer than a minimum of 42 inches 107 cm from center to center to avoid interference cross talk between Heart Rate monitors DO keep the area around your Recumbent Exercise Bike clear of any obstructions including walls and furniture DO verify the contents of the delivery carton against the accompanying Parts Listing prior to setting the cartons and shipping material aside If any parts are missing contact Life Fitness Customer Support Services at the number listed in the Operation Manual Sav2. Feed the WIRE HARNESSES at the top of the FRAME POST through the bottom of the CONSOLE SUPPORT ASSEMBLY COLUMN Continue pushing the WIRE HARNESSES until the CONNECTORS at the end of the WIRE HARNESSES exit through the opening at the top of the COLUMN Gently pull the WIRE HARNESSES to remove the slack Position the CONSOLE SUPPORT ASSEMBLY 6 so that the HANDLEBAR is facing the user and slide the CONSOLE SUPPORT ASSEMBLY into the FRAME POST D being careful not to pinch the WIRES in the process Align the holes in the top of the CONSOLE SUPPORT ASSEMBLY with those in the FRAME POST Install the four CONSOLE SUPPORT ASSEMBLY BOLTS 8 to secure it into position Tighten the four CONSOLE SUPPORT ASSEMBLY BOLTS to 15 20 ft Ibs NOTE BE VERY CAREFUL NOT TO DAMAGE THE WIRES WHEN PASSING THE BOLTS THROUGH THE HOLES TIGHTEN THE BOLTS SECURELY MISE EN GARDE FAITES ATTENTION TRES A NE PAS ENDOMMAGER LES FILS EN PASSANT LES BOULONS PAR LES TROUS SERREZ LES BOULONS SOLIDEMENT Align the LOCKING TABS of the 10 PIN CONNECTOR and the 4 PIN CONNECTOR and plug them together until they SNAP into place Carefully feed the wires back into the top of the CONSOLE SUPPORT ASSEMBLY 6 and attach the DISPLAY CONSOLE 7 to the CONSOLE SUPPORT ASSEMBLY using the four CONSOLE SCREWS 4 and a Phillips screwdriver Tighten the four SCREWS in a criss cross pattern NOTE BE CAREFUL NOT TO OVER TIGHTEN THE SCREWS MISE EN GARDE VEILLER A N
3. E PAS TROP SERRER LA VIS 9 After placing the exercise bike in the intended location for use check the stability of the bike If the exercise bike is not level turn a LEVELER G in the rear STABILIZER BAR H in either direction until the rocking motion is eliminated Tighten the JAM NUT J when the exercise bike is level NOTE ONLY ONE LEVELER NEEDS TO BE TURNED REMARQUE NE TOURNER QU UN SEUL VERIN 10 Locate the RIGHT PEDAL STRAP 10 marked with an R Attach the RIGHT PEDAL STRAP to the RIGHT PEDAL k with the double slot on the inward pedal strap tab looping upward and attaching to the outward pedal strap tab Repeat for the LEFT PEDAL STRAP 9 marked with an L Physical Dimensions Length 54 inches 137 centimeters 54 inches 137 centimeters 54 inches 1 137 centimeters Width 26 inches 66 centimeters 26 inches 66 centimeters 26 inches 66 centimeters Height 51 inches 129 centimeters 51 inches 129 centimeters 51 inches 129 centimeters Weight 134 pounds 61 kilograms 134 pounds 61 kilograms 134 pounds 61 kilograms PRE OPERATION CHECKLIST Y Ensure that the console support screws are tight VY Make sure the Recumbent Exercise Bike is properly leveled and stable Y Ensure that the Leveler Jam Nuts are tight v Read the entire Operation Manual before using the Recumbent Exercise Bike Before attempting to operate your Recumbent Exercise Bike it is imperative that you familiarize
4. e the shipping cartons in case of return DO read the entire Operation Manual prior to attempting to operate this machine as this is essential for proper use NE PAS placer le v lo d exercice allong Lifecycle a l ext rieur pres d une piscine ou dans un endroit tres humide NE PAS faire fonctionner le velo d exercice allong Lifecycle s il est tomb s il a t endommag ou s il a t partiellement plong dans l eau T l phoner au service apr s vente de Life Fitness dont le num ro figure sur la couverture arri re du guide d installation NE PAS placer le v lo d exercice allong Lifecycle a moins de 76cm 30 po dun poste de t l vision MAINTENIR la zone autour du v lo d exercice allong Lifecycle libre de toute obstruction y compris murs et meubles VERIFIER si l emballage contient toutes les pi ces de la liste jointe avant de le mettre de c t Si des pi ces manquent t l phoner au service apr s vente de Life Fitness dont le num ro figure sur la couverture arri re du guide d installation Conserver l emballage au cas ou l appareil devrait tre renvoy LIRE le manuel de l utilisateur tout entier avant d essayer de faire fonctionner cet appareil Ceci est indispensable son utilisation correcte TOOLS REQUIRED FOR ASSEMBLY Phillips screwdriver 3716 hex key wrench T 40 Torx wrench PARTS DESCRIPTION K Seat Back Screw Qty 4 k Seat Back Washer Qty 4 Ki Console Support Assembly Bolt Qty 4 Ki C
5. onsole Screw Qty 4 K Seat Back Qty 1 Li Console Support Assembly Qty 1 Display Console Qty 1 Li Accessory Tray Assembly Qty 1 Li Left Pedal Strap Qty 1 Ld Right Pedal Strap Qty 1 D 2 CTT O 9 0 ET Please read this prior to assembly This product is preconfigured to accept the addition of the Life Fitness Entertainment System A POWER CABLE and COAXIAL CABLE have been pre installed Please read both the product assembly instructions and Entertainment Ready assembly instructions included with the Life Fitness Entertainment System prior to assembly Route the POWER CABLE and COAXIAL CABLE alongside the MAIN WIRE HARNESS where applicable Slide the ACCESSORY TRAY 8 if so equipped over the user right seat back post and down to make contact with the SEAT HANDLEBAR Position the underside clamp bracket A around the SEAT HANDLEBAR and tighten the two clamp SCREWS and WASHERS B NOTE BE CAREFUL NOT TO OVER TIGHTEN THE SCREWS MISE EN GARDE VEILLER A NE PAS TROP SERRER LA VIS Align the four holes in the SEAT BACK 5 with those in the SEAT BACK POSTS Insert the four SCREWS 1 and WASHERS 2 through the backside of the SEAT BACK POSTS and into the SEAT BACK Tighten the four SCREWS with a hex key wrench NOTE BE CAREFUL NOT TO OVER TIGHTEN THE SCREWS MISE EN GARDE VEILLER A NE PAS TROP SERRER LA VIS Unfold the CONSOLE WIRE HARNESSES C from the POST extending from the FRAME
6. yourself with the contents of the Operation Manual If your Recumbent Exercise Bike does not respond as described in the OPERATION MANUAL contact the nearest Life Fitness service center as listed in the Operation Manual BUILT TO LEAD 2006 Life Fitness a division of Brunswick Corporation All rights reserved Life Fitness is trademark of Brunswick Corporation Polar is a registered trademark of Polar Electro Inc M051 00K39 A140 11 06 SSS a RREH
Download Pdf Manuals
Related Search