Life Fitness LC85R User's Manual
Contents
1. of Polar Electro Inc M051 00K20 A327 8 022. 31 0017 00104 0253 Console Support Assembly Bolt Console Screw Qty 4 0017 00101 1737 0017 00101 1253 Console Support Assembly Qty 1 AK39 00003 0000 Accessory Tray Assembly If so equipped 1 Right Pedal Strap Qty 1 9V Battery Model 8500 Only 0017 00003 0757 O 2 O G mO e Slide the ACCESSORY TRAY 8 if so equipped over the user right seat back post and down to make contact with the SEAT HANDLEBAR Position the underside clamp bracket A around the SEAT HANDLEBAR and tighten the two clamp SCREWS and WASHERS B NOTE BE CAREFUL NOT TO OVER TIGHTEN THE SCREWS MISE EN GARDE VEILLER NE PAS TROP SERRER LA VIS Align the four holes in the SEAT BACK 5 with those in the SEAT BACK POSTS Insert the four SCREWS 1 and WASHERS 2 through the backside of the SEAT BACK POSTS and into the SEAT BACK Tighten the four SCREWS with a hex key wrench NOTE BE CAREFUL NOT TO OVER TIGHTEN THE SCREWS MISE EN GARDE VEILLER A NE PAS TROP SERRER LA VIS Unfold the CONSOLE WIRE HARNESSES C from the POST extending from the FRAME Feed the WIRE HARNESSES at the top of the FRAME POST through the bottom of the CONSOLE SUPPORT ASSEMBLY COLUMN Continue pushing the WIRE HARNESSES until the CONNECTORS at the end of the WIRE HARNESSES exit through the opening at the top of the COLUMN Gently pull the WIRE HARNESSES to remove the slack Position the CONSOLE SUPPORT ASSEM
3. BLY 6 so that the HANDLEBAR is facing the user and slide the CONSOLE SUPPORT ASSEMBLY into the FRAME POST D being careful not to pinch the WIRES in the process Align the holes in the top of the CONSOLE SUPPORT ASSEMBLY with those in the FRAME POST Install the four CONSOLE SUPPORT ASSEMBLY BOLTS 8 to secure it into position Tighten the four CONSOLE SUPPORT ASSEMBLY BOLTS to 15 20 ft Ibs NOTE BE VERY CAREFUL NOT TO DAMAGE THE WIRES WHEN PASSING THE BOLTS THROUGH THE HOLES TIGHTEN THE BOLTS SECURELY MISE EN GARDE FAITES ATTENTION TR S NE PAS ENDOMMAGER LES FILS EN PASSANT LES BOULONS PAR LES TROUS SERREZ LES BOULONS SOLIDEMENT Align the LOCKING TABS of the 10 PIN CONNECTOR and the 4 PIN CONNECTOR Models 9500HR and plug them together until they SNAP into place Model 8500 Only Remove the BATTERY DOOR E located on the back of the DISPLAY CONSOLE 7 Carefully pull the BATTERY WIRE HARNESS F out of the BATTERY COMPARTMENT Plug the BATTERY 11 into the BATTERY WIRE HARNESS CONNECTOR Carefully place the BATTERY and BATTERY WIRE HARNESS into the BATTERY COMPARTMENT Replace the BATTERY DOOR 9 Carefully feed the wires back into the top of the CONSOLE SUPPORT ASSEMBLY 6 and attach the DISPLAY CONSOLE 7 to the CONSOLE SUPPORT ASSEMBLY using the four CONSOLE SCREWS 4 and a Phillips screwdriver Tighten the four SCREWS in a criss cross pattern NOTE BE CAREFUL NOT TO OVER TIGHTEN THE SCREWS M
4. Exercise Bike ASSEMBLY INSTRUCTIONS Congratulations and welcome to the world of Life Fitness and the Life Fitness 9500HR 9100 8500 Recumbent Exercise Bikes The following Parts Identification Listing and the step by step assembly procedures have been assembled to make the set up of the Recumbent Exercise Bikes as quick and easy as possible Please take special note of the following important points prior to choosing a location and beginning assembly of the Recumbent Exercise Bikes IMPORTANT SAFETY INSTRUCTIONS DO NOT locate the Recumbent Exercise Bike outdoors near swimming pools or in areas of high humidity DO NOT operate your Recumbent Exercise Bike if it has been dropped damaged or even partially immersed in water Contact Life Fitness Customer Support Services at the number in the Operation Manual DO NOT locate the Recumbent Exercise Bike any closer than 30 inches 76 cm to a television set DO NOT locate additional Recumbent Exercise Bike any closer than a minimum of 42 inches 107 cm from center to center to avoid interference cross talk between Heart Rate monitors DO keep the area around your Recumbent Exercise Bike clear of any obstructions including walls and furniture DO verify the contents of the delivery carton against the accompanying Parts Listing prior to setting the cartons and shipping material aside If any parts are missing contact Life Fitness Customer Support Services at the number
5. ISE EN GARDE VEILLER A NE PAS TROP SERRER LA VIS 10 After placing the exercise bike in the intended location for use check the stability of the bike If the exercise bike is not level turn a LEVELER G in the rear STABILIZER BAR H in either direction until the rocking motion is eliminated Tighten the JAM NUT J when the exercise bike is level NOTE ONLY ONE LEVELER NEEDS TO BE TURNED REMARQUE NE TOURNER QU UN SEUL VERIN 11 Locate the RIGHT PEDAL STRAP 10 marked with an R Attach the RIGHT PEDAL STRAP to the RIGHT PEDAL with the double slot on the inward pedal strap tab looping upward and attaching to the outward pedal strap tab Repeat for the LEFT PEDAL STRAP 9 marked with an L PRE OPERATION CHECKLIST v Ensure that the console support screws are tight v Make sure the Recumbent Exercise Bike is properly leveled and stable v Ensure that the Leveler Jam Nuts are tight v Read the entire Operation Manual before using the Recumbent Exercise Bike Before attempting to operate your Recumbent Exercise Bike it is imperative that you familiarize yourself with the contents of the Operation Manual If your Recumbent Exercise Bike does not respond as described in the OPERATION MANUAL contact the nearest Life Fitness service center as listed in the Operation Manual 2002 Brunswick Corporation All rights reserved Life Fitness is a trademark of Brunswick Corporation Polar is a registered trademark
6. listed in the Operation Manual Save the shipping cartons in case of return DO read the entire Operation Manual prior to attempting to operate this machine as this is essential for proper use NE PAS placer le v lo d exercice allong Lifecycle l ext rieur pr s d une piscine ou dans un endroit tr s humide NE PAS faire fonctionner le v lo d exercice allong Lifecycle s il est tomb s il a t endommag ou s il a t partiellement plong dans l eau T l phoner au service apr s vente de Life Fitness dont le num ro figure sur la couverture arri re du guide d installation NE PAS placer le v lo d exercice allong Lifecycle moins de 76 cm 30 po d un poste de t l vision MAINTENIR la zone autour du v lo d exercice allong Lifecycle libre de toute obstruction y compris murs et meubles V RIFIER si l emballage contient toutes les pi ces de la liste jointe avant de le mettre de c t Si des pi ces manquent t l phoner au service apr s vente de Life Fitness dont le num ro figure sur la couverture arri re du guide d installation Conserver l emballage au cas o l appareil devrait tre renvoy LIRE le manuel de l utilisateur tout entier avant d essayer de faire fonctionner cet appareil Ceci est indispensable son utilisation correcte TOOLS REQUIRED FOR ASSEMBLY Phillips screwdriver 3 16 hex key wrench T 40 Torx wrench PARTS DESCRIPTION Seat Back Screw Seat Back Washer Qty 4 0017 00101 11
Download Pdf Manuals
Related Search