Life Fitness Classic Series Cross-Trainer CLSXH User's Manual
Contents
1. Llassic Series Lross l rainer Model LLSXH ASSEMBLY INSTRUCTIONS Congratulations and welcome to the world of ALTES The follovving Parts List and the step by step assembly procedures have been assembled to make the set up of the Cross Trainer as quick and easy as possible Please take special note of the following important points prior to choosing a location and beginning assembly of the Cross Trainer IMPORTANT SAFETY INSTRUCTIONS DO NOT LOCATE THE CROSS TRAINER OUTDOORS NEAR SWIMMING POOLS OR IN AREAS OF HIGH HUMIDITY DO NOT OPERATE YOUR CROSS TRAINER IF IT HAS BEEN DROPPED DAMAGED OR EVEN PARTIALL Y IMMERSED IN WATER IF THIS OCCURS CONTACT LIFE FITNESS CUSTOMER SUPPORT SERVICES AT THE NUMBER IN THE OPERATION MANUAL DO NOT LOCATE THE CROSS TRAINER ANY CLOSER THAN 30 INCHES 76 CM TO A TELEVISION SET DO NOT LOCATE ADDITIONAL CROSS TRAINERS ANY CLOSER THAN 42 INCHES 107 CM FROM CENTER TO CENTER TO AVOID INTERFERENCE CROSS TALK BETWEEN HEART RATE MONITORS DO KEEP THE AREA AROUND YOUR CROSS TRAINER CLEAR OF ANY OBSTRUCTIONS INCLUDING WALLS AND FURNITURE ENSURE THAT THERE IS AT LEAST A 12 INCH 30 CM CLEARANCE IN FRONT OF THE CROSS TRAINER DO VERIFY THE CONTENTS OF THE DELIVERY CARTON AGAINST THE ACCOMPANYING PARTS LIST PRIOR TO SETTING THE CARTONS AND SHIPPING MATERIAL ASIDE IF ANY PARTS ARE MISSING CONTACT LIFE FITNESS CUSTOMER SUPPORT SERVICES AT THE NUMBER LISTED IN THE OPERATION MANU2. center as listed in the Operation Manual Life Fitness Customer Support Services 800 351 3737 or 847 451 0036 Prior to your call please be sure you have located and noted the MODEL NUMBER SERIAL NUMBER The Model amp Serial number information of your Life Fitness Cross Trainer is listed on a label located on the rear stabilizer BUILT TO LEAD 2008 Life Fitness a division of Brunswick Corporation All rights reserved Life Fitness Lifepulse FlexDeck and Smart Stop are trademarks of Brunswick Corporation MO51 00K62 A207 04 08
3. AL SAVE THE SHIPPING CARTONS IN CASE OF RETURN DO READ THE ENTIRE OPERATION MANUAL PRIOR TO ATTEMPTING TO OPERATE THIS MACHINE AS THIS IS ESSENTIAL FOR PROPER USE CONSIGNES DE SECURITE IMPORTANTES NE PLACEZ PAS L APPAREIL A L EXT RIEUR PRES D UNE PISCINE OU DANS UN ENDROIT TRES HUMIDE NE FAITES PAS FONCTIONNER L APPAREIL S IL EST TOMB S IL A T ENDOMMAG OU S IL A T PARTIELLEMENT PLONG DANS L EAU SI CELA S EST PRODUIT CONTACTEZ LE SERVICE APRES VENTE DE LIFE FITNESS AU NUM RO FOURNI DANS LE MANUEL D UTILISATION NE PLACEZ PAS L APPAREIL MOINS DE 76 CM D UN POSTE DE T L VISION NE PLACEZ PAS D AUTRES APPAREILS DU M ME TYPE PROXIMIT UN ESPACE D AU MOINS 107 CM DOIT TRE OBSERV ENTRE LES PARTIES CENTRALES DE DEUX APPAREILS AFIN D VITER LES INTERF RENCES ENTRE LES CONTR LEURS DE RYTHME CARDIAQUE MAINTENEZ LA ZONE AUTOUR DE L APPAREIL LIBRE DE TOUTE OBSTRUCTION Y COMPRIS MURS ET MEUBLES VEILLEZ LAISSER UN D GAGEMENT D AU MOINS 30 CM DEVANT L APPAREIL VERIFIEZ SI L EMBALLAGE CONTIENT TOUTES LES PI CES DE LA LISTE JOINTE AVANT DE LE METTRE DE C T SI DES PI CES SONT ABSENTES CONTACTEZ LE SERVICE APR S VENTE DE LIFE FITNESS AU NUM RO INDIQU DANS LE MANUEL D UTILISATION CONSERVEZ L EMBALLAGE AU CAS O VOUS DEVRIEZ RENVOYER L APPAREIL LISEZ LE MANUEL DE L UTILISATEUR TOUT ENTIER AVANT D ESSAYER DE FAIRE FONCTIONNER CET APPAREIL CECI EST INDISPENSABLE SON UTILISATION CORRECTE
4. TOOLS REQUIRED FOR ASSEMBLY Magnetic 2 Bit Phillips Screwdriver T 45 Hex Key Wrench 16mm Open End Wrench 7 Torx Socket Head Screw M8 1 25 x 19 0017 00101 1791 Phillips Pan Head Screvv M4 2 0 70 x 10 0017 00101 1846 Front Rocker Cover OK62 01009 0000 Console Support Assembly OK62 00123 0000 Front Pivot Arm Cover OK62 01012 0000 Left User Arm Assembly AK62 00087 0000 Left Bullhorn AK62 00054 0000 Left Bullhorn Cover OK62 01008 0001 Accessory Tray OK62 01022 0000 Base Frame Cap OK62 01004 0000 Cap Console Support OK62 01030 0000 PARTS DESCRIPTION Qty 16 Qty 2 Qty 2 Qty 1 Qty 2 Qty 1 Qty 1 Qty 1 Qty 1 Qty 1 Qty 1 Phillips Pan Head Screw M4 0 70 x 19 0017 00101 1796 Console Assembly Left Back Rocker Cover OK62 01011 0000 Console Support Cover OK62 01023 0000 Rear Pivot Arm Cover OK62 01013 0000 Right User Arm Assembly AK62 00086 0000 Right Bullhorn AK62 00053 0000 Right Bullhorn Cover OK62 01007 0001 Right Back Rocker Cover OK62 01010 0000 Foot Cover OK62 01003 0000 Phillips Pan Head Screw M4 0 70 x 44 0017 00101 1854 IMPORTANT DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE PEDAL LEVERS ALL NECESSARY COMPONENTS NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT IMPORTANT NE JETEZ PAS LE KIT PLAC SUR LE DESSUS DES LEVIERS DE P DALE IL CONTIENT TOUS LES L MENTS NECESSAIRES POUR L INSTALLATION 1 Loc
5. ULLHORN 13 Secure the BULLHORN to the BULLHORN MOUNTING BRACKET D using two FLAT HEAD SCREWS 1 Tighten the SCREWS securely Locate and attach the LEFT BULLHORN COVER 15 to the base of the BULLHORN using one SCREW 22 Tighten the SCREW securely Do not over tighten the SCREW Slide the GASKET E downward to meet the BULLHORN COVER 5 Repeat steps one through four to install the RIGHT ROCKER COVERS 5 6 PIVOT ARM COVERS 9 amp 10 BULLHORN 14 and BULLHORN COVER 16 NOTE THE RIGHT PIVOT ARM COVERS ARE REVERSED FRONT AND BACK THE SCREWS WILL BE INSTALLED FROM THE REAR 6 Unwrap the MAIN WIRE and HEART RATE HARNESS F amp G leading from the MONOCOLUMN H Feed the WIRE HARNESSES through the CONSOLE SUPPORT ASSEMBLY TUBE I located at the top and front of the MONOCOLUMN Locate the CONSOLE SUPPORT ASSEMBLY 7 and position it near the top of the MONOCOLUMN Feed the WIRE HARNESSES through the CONSOLE SUPPORT ASSEMBLY as shown Align the bottom mounting holes of the CONSOLE SUPPORT ASSEMBLY with those in the CONSOLE SUPPORT ASSEMBLY TUBE Secure them together using six SCREWS 1 Tighten the SCREWS securely NOTE BE CAREFUL NOT TO DAMAGE THE WIRE HARNESSES E amp F WHEN ROUTING IT THROUGH THE CONSOLE SUPPORT ASSEMBLY OR WHEN MOUNTING THE CONSOLE SUPPORT ASSEMBLY TO THE CONSOLE SUPPORT ASSEMBLY TUBE 7 Locate the ACCESSORY TRAY 17 Slide the ACCESSORY TRAY into the top of the MONOCOLUMN H as shown Be sur
6. ate the LEFT HANDLEBAR 11 Position the HANDLEBAR near the top of the LEFT PIVOT ARM A If equipped with Lifepulse connect the 2 PIN HEART RATE CONNECTOR B leading from the HANDLEBAR to the 2 PIN CONNECTOR C extending from the top of the LEFT PIVOT ARM Carefully slide the excess HEART RATE CABLE into the top of the LEFT PIVOT ARM Align the mounting holes of the LEFT HANDLEBAR with the mounting holes at the top of the LEFT PIVOT ARM Secure them together using three SCREWS 1 NOTE BE CAREFUL NOT TO PINCH THE HEART RATE CABLE WHEN SECURING THE LEFT HANDLEBAR TO THE LEFT PIVOT ARM 2 Locate one LEFT FRONT ROCKER COVER 5 and the LEFT BACK ROCKER COVER 6 Position the LEFT BACK ROCKER COVER over the user side of the ROCKER ARM making sure that it seats fully over the BULLHORN MOUNTING BRACKET D Place the FRONT ROCKER COVER over the opposite side of the ROCKER ARM in the same manner Secure the COVERS using two PHILLIPS PAN HEAD SCREWS 2 Tighten the SCREWS securely Do not over tighten the SCREWS 3 Locate one FRONT PIVOT ARM COVER 9 and one BACK PIVOT ARM COVER 10 Position the BACK PIVOT ARM COVER over the user side of the ROCKER ARM making sure that it interlocks with the ROCKER COVER Place the FRONT PIVOT ARM COVER over the opposite side of the PIVOT ARM in the same manner Secure the COVERS using two PHILLIPS PAN HEAD SCREWS 2 Tighten the SCREWS securely Do not over tighten the SCREWS 4 Locate the LEFT B
7. e the ACCESSORY TRAY is fully seated NOTE BE CAREFUL NOT TO DAMAGE THE MAIN WIRE HARNESS WHEN SLIDING THE ACCESSORY TRAY INTO THE MONOCOLUMN Secure the accessory tray to the CONSOLE SUPPORT ASSEMBLY using two SCREWS 3 Tighten the SCREWS securely Do not over tighten the SCREWS 10 11 12 13 Locate the DISPLAY CONSOLE 4 Position the CONSOLE near the top of the CONSOLE BRACRET Attach all CONNECTORS F amp G leading from the CONSOLE BRACKET to their corresponding CONNECTORS in the back of the DISPLAY CONSOLE Feed any excess WIRE HARNESS into the CONSOLE BRACKET and place the DISPLAY CONSOLE onto the CONSOLE BRACKET aligning the mounting holes Secure the DISPLAY CONSOLE using four SCREWS 2 Tighten the SCREWS securely Do not over tighten the SCREWS Locate the CONSOLE SUPPORT COVER 8 Position the CONSOLE BRACKET COVER over the underside of the CONSOLE SUPPORT ASSEMBLY 7 as shown and secure it using two SCREWS 2 Tighten the SCREWS securely Do not over tighten the SCREWS Locate the CONSOLE SUPPORT CAP 21 Snap the CAP into position at the top of the CONSOLE SUPPORT COVER Locate the BASE FRAME CAP 19 Remove the two SCREWS J securing the front of the BASE FRAME COVER K to the BASE FRAME L Position the CAP over the front of the BASE FRAME as shown sliding the mounting tabs to the inside of the BASE FRAME COVER Secure the CAP using two SCREWS J previously removed Tighten THE SCREWS secu
8. rely Do not over tighten the SCREWS Locate the four FOOT COVERS 20 Align the COVERS with the ends of the STABILIZER BARS M Insert the post on the underside of the FOOT COVERS into the mounting holes on the top of each STABILIZER Press the FOOT COVERS firmly into position Position the unit into the desired location for use Properly level the unit according to the instructions in the Operation Manual PRE OPERATION CHECKLIST Y Ensure that all fasteners are tight Y Make sure the CROSS TRAINER is properly leveled and stable Refer to the Operation Manual Y Ensure that the Leveler Jam Nuts are tight Refer to the Operation Manual Y Read the entire Operation manual before using the Cross Trainer LISTE DES V RIFICATIONS A EFFECTUER AVANT LA MISE EN MARCHE v V rifiez si tous les dispositifs de fixation sont serr s v V rifiez si APPAREIL D EXERCICE POLYVALENT est de niveau et stable R f rez vous au manuel d utilisation v V rifiez si les contre crous des v rins de mise niveau sont serr s R f rez vous au manuel d utilisation v Lisez le manuel d utilisation dans son int gralit avant d utiliser l appareil d exercice polyvalent Before attempting to operate your Cross Trainer it is imperative that you familiarize yourself with the contents of the Operation Manual If your Cross Trainer does not respond as described in the Operation Manual contact the nearest Life Fitness service
Download Pdf Manuals
Related Search