Liebherr Kitchen Entertainment Center 7083-103-00 User's Manual
Contents
1. Adjust the height of the appliance atthe front by twisting the adjustable feet A F 27 Use theopen endedspanner provided Caution The front feet of the ap pliance must be firmly placed on the floor 2 Adjustthe height ofthe appliance atthe rear by turning the adjusting bars Q Turn the adjusting bars clock wise untilthe compressor mount ing plate touches the anti tipping bracket Adjusting the front of the drawer If required the front of the freezer drawers can be adjusted Transfer the screws shown in the illustration on the left and right sides of the freezer drawer individually to the long slots below Tighten the screws in the front of the drawer once it is in the right position Side view of the freezer drawer pulled out 10 Fasten the appliance in the recess a TN Fasten the appliance in the recess through the upper and X lower hinges of the refrigerator doors Use 2 screws for each hinge screws 4x 16 mm Before fitting the door panels Remove the cover and unscrew the attachment bracket from the refrigerator doors These attachment brackets will be mounted onto the refrigerator door panels Important The securing nuts are needed for re mounting the pre assembled door panels onto the refrigerator doors Unscrew the attachment brackets from the freezer drawers These attachment brackets will be mounte2. the unit and the rear edge of the anti tipping bracket is Inset installation style gt 610 mm panel thickness Frameless installation style gt 610 mm Connection to the water supply Safety instructions and warnings e Do not connect to the water supply while the combined refrig erator freezer is connected to the electricity supply e The connection to the mains water supply may only be made by trained personnel e The water quality must comply with the drinking water directives of the country in which the appliance is used e The ice maker is designed exclusively to make ice cubes in quantities required by a household and may only be operated with water suitable for this purpose e All repairs and work on the ice maker may only be carried out by customer service personnel or other trained personnel e The manufacturer cannot accept liability for damage caused by a faulty connection to the mains water supply Water pressure The water pressure must be between 150 and 600 KPa 1 5 6 bar Important If the water filter isinserted inthe appliance the water pressure must lie between 300 and 600 KPa 3 6 bar If the water pressure with the inserted water filter is too low this may cause the ice maker to malfunction The water supply to the appli ance must be through a cold water pipe that can withstand the operating pressure and complies with the hygiene regulations D Q For this use the s
3. Installation instructions for NoFrost combined refrigerator freezers gt m Gr lt a In id ae C C a 7083 103 00 ECBN 62 Setting up e Avoid positioning the appliance in direct sunlight or near cook ers radiators and similar sources of heat The floor on which the appliance stands should be horizontal and level The ventilation grilles should not be obstructed Always ensure that there is good ventilation and that the outward flowing air is able to escape Standard EN 378 specifies that the room in which you install your appliance must have a volume of 1 m per 8 g of R 600a refrigerant used in the appliance so as to avoid the formation of inflammable gas air mixtures in the room where the appliance is located in the event of a leak in the refrigerant circuit The quantity of refrigerant used in your appliance is indicated on the type plate on the inside of the appliance Electrical connection Only operate the appliance with alternating current AC The permissible voltage and frequency are indicated on the type plate The socket must be properly earthed and protected by a fuse The tripping current of the fuse must be between 10 A and 16 A The socket must not be situated behind the appli ance and must be easily accessible Do n
4. allation Style Right side wall of appliance housing i 5mm 10 mm 15mm Front of 20 mm F appliance housing 25 mm 30 mm Top View Sa mi 40 mm 5mm 10mm 20 mm 30 mm Panel 2 40 mm thickness Front panel door closed O som 16 mm 60 mm 19 mm 70 mm ay 80 mm 3 O 3 90 mm a 100 mm S 110 mm 2 Q 120 mm 3 5 130 mm col 3 140 mm oOo y 150 mm a 160 mm 19 mm Panel 16 mm thickness Mounting the anti tipping device BE A WARNING 7 The supplied anti tipping bracket must be installed in all cases This prevents the appliance from tipping over when the fully loaded door is opened E A CAUTION m Ensure that there are no electric cables or water pipes in the wall section to which the anti tipping bracket is to be secured These could be damaged during installation Important When securing the anti tipping bracket to a concrete floor use suitable plugs If the floor slopes down sideways the anti tipping bracket must be fitted horizontally Lay down spacers in the appropriate positions 1 Mark the centre line of the appliance on the floor Align the anti tipping bracket centre to the centre line 2 Secure the anti tipping bracket to the floor using the 3 screws 6 mm x 60 mm included in the accessory pack The distance E between the leading edge of the body of
5. by undoing the left and right screws Tighten the screws w Pull out the bottom freezer drawer and mount the panel in the same way 4 For both drawers cover the gap between the drawer and the panel with the cover strips supplied Remove the protective film from the trim and insert into the gap at the top 3 5 x 13 mm Mounting the dust filter The supplied dustfilter prevents thatdirt enters the motor compart ment reducing the refrigeration performance Therefore always install the dust filter 1 Pull the bottom freezer drawer right out 2 Remove the protective film from the dust filter Insert the filter at the bottom press the button down and click the filter into place Mounting the ventilation grille Important To ensure fault free operation of the appliance you must install the supplied ventilation grille Do not obstruct the ventilation opening or cover it with a panel 15 Liebherr Hausgerate Lienz GmbH Dr Hans Liebherr Strasse 1 A 9900 Lienz www liebherr com
6. d onto the freezer panels Important The screws are needed for re mounting the pre assembled freezer panels onto the freezer drawers DAD b Mounting the attachment brackets onto the door panels Mark lines on the refrigerator door panels as shown in Fig A Align the dismounted brackets of the refrigerator doors to the lines on the refrigerator door panels as shown in Fig A 1 Fasten each bracket with any hole wherever possible using a minimum of 6 screws 4 x 16 mm Fasten the brackets provided onto the freezer drawer panels using three screws 4 x 16 mm for each bracket Fig A2 25 5 mm 25 5mm eH s E E a A i HII Refrigerator door panels 1041 mm 3mm Co Freezer drawer panel Fig A 2 880 mm Freezer drawer panel 3 mm 880 mm CO Fig A Fig A 2 11 12 Mounting the refrigerator panel The description is for one panel only The procedure is the same for both panels 1 Open the refrigerator door and suspend the refrigerator panel on the top adjusting pins fig B 2 Screw securing nuts onto the adjusting pins and slightly tighten fig B 3 Close the refrigerator door and check the height of the panel 4 Adjustthe height of the panel if necessary Undo the securing nuts and use the adjusting pins to adjust fig C To make it possible to fasten the refrigerator panel at the bottom the soft stop cylinder mus
7. ot connect the appliance using an exten sion cable or extension socket Do notuse stand alone inverters conversion of direct current to alternating current three phase current or energy saving plugs Risk of damage to the electronic control system Appliance dimensions A 76mm B 2027 mm C 910 mm D 76 mm E 610 mm G 1078 mm H 943 mm Appliance venting HL ts The required air flow is directed through the plinth It is important to use the provided ventilation grille for the ventila tion opening The ventilation opening must not be obstructed or covered with a panel Installation dimensions The ice maker is fitted in the freezer compartment of the com bined refrigerator freezer It must be connected to the mains water supply to work The socket must be positioned within the areas marked in grey or above the installation recess The water shut off tap must be positioned within the areas marked in grey ees WARNING EEE The water shut off tap must not sit directly above the socket The gap between the water shut off tap and the socket must comply with the regulations of the country in which the appliance is used 2300 mm 2032 mm 2000 mm 915 mm Cabinet depth D 625 mm panel thickness gt Inset installation style 625 mm gt Frameless installation style Explanation of Installation style
8. s see page 4 Definition of Inset Installation Style Appliance and panels sit fully within the opening and are flush with what could be its own box between two pantry cabinets or decorative columns Side view of cabinet sectional view MMMM lt Cabinet frame lt lt Door panel Definition of Frameless Installation Style With this installation style these wider appliance panels partially overlay the shared side gables of adjacent cabinetry so as to mimic the look of a frameless style cabinet Side view of cabinet sectional view Cabinet frame y Panel dimensions Inset installation style Panel dimensions Frameless installation style Min panel thickness 16 mm Max panel thickness 19 mm Maximum panel weight Refrigerator panel 12 kg Freezer drawer panel 10 kg 460 mm 460 mm 1162 mm Door swing clearance Inset Installation Style 5mm i 10 mm Right side wall of appliance housing mel an Front of 20 mm i appliance housing 25 mm 30 mm Top View ann 40 mm 5 mm 10 mm 20 mm 30 mm Panel 40 mm thickness Front panel door closed 16 MID 19 mm 50 mm 60 mm 70 mm 100 mm 110 mm 120 mm 130 mm 140 mm 150 mm TTT TT TTT Tee ee ee ee PT TT TT o O oO 3 3 3 3 160 mm Tee mm Panel 16 mm thickness Door swing clearance Frameless Inst
9. t be dismantled 6 Grasp the soft stop cylinder and pull down Fig D The soft stop cylinder retracts in the detached state fig D 7 Transfer the lower edge of the attachment bracket onto the panel using a pencil fig E Remove the panel from the refrigerator door fig E 7 Dismantle the lower attachment bracket from the refrigerator door Align the bracket to the lines on the refrigerator door panel fig G Fasten the bracket with any hole wherever possible using a minimum of 6 screws 4 x 16 mm 8 Opentherefrigerator doorand suspend the refrigerator panel on the top adjusting pins fig H 9 Screw securing nuts onto the adjusting pins and slightly tighten fig H 10 Move the panel to the left until it makes contact with the center rail fig I 11 Tighten the hex nuts finally 12 Fasten the refrigerator panel using the same screws that held the lower bracket before removal fig K Qm m fig K 13 Extend the soft stop cylinder and connect with the ball stud fig L 14 Click cover into place fig M fig M 13 14 Mounting the freezer panels 1 Pulloutthe top freezer drawer and screwonthe pre assembled panel The same screws must be used as those used to screw on the attachment brackets 3 5 x 13 2 Close the freezer drawer and check the position of the panel Adjust the height of the panel
10. tainless steel hose supplied length 3 m Installation 1 Place the appliance in front of the installation recess 2 Apply cover strips on the side walls of the appli ance 3 Insert the bent section of the hose through the opening at the rear of the appliance 4 Connect the hose to the solenoid valve at the front side of the appliance 5 Route the mains cable towards the socket 6 Route the water hose towards the water shut off tap ZZ VAN WARNING Do not connect the appliance to the power supply until the installation is completed es CAUTION HEMER Lay the mains cable and the water hose in such a way that they will not be damaged when the appliance is slid into the installation recess 7 Push the appliance slowly into the recess until the compressor mounting plate touches the anti tipping bracket U A WARNING To prevent the appliance from tipping forwards the com pressor mounting plate must be touching the anti tipping bracket Anti tipping bracket Compressor mounting plate 8 Connect the hose to the shut off tap Open the shut off tap and check the system for leakage Important After the ice maker has been switched on the water supply system must be bled See the section Bleeding the ice maker in the operating instructions Levelling the appliance 1
Download Pdf Manuals
Related Search