Home

Lenovo 388 User's Manual

1. H o oa 4 en es q E H Figure 99 Removing the screws that secure the system board 13 Place both the old system board and the new system board on a clean flat and ESD safe surface 164 ThinkServer Hardware Maintenance Manual 14 For the new system board gently press down the small handle on the microprocessor socket and then pull the handle a little bit outward to release it from the secured position Then pivot the handle upward until the handle and the microprocessor retainer are in the fully open position Remove the microprocessor socket cover from the new system board Notes a Your microprocessor socket and cover might look slightly different from the illustration b Do not drop anything onto the microprocessor socket while it is exposed The socket pins must be kept as clean as possible Figure 100 Removing the microprocessor socket cover 15 Remove the microprocessor from the old system board and install it directly on the new system board See Replacing the microprocessor on page 157 16 The old system board must be returned with a microprocessor socket cover to protect the pins on the socket during shipping and handli
2. Figure 54 Removing the EMI shield for the upper optical drive 116 ThinkServer Hardware Maintenance Manual e f you replacing an optical drive disconnect the signal cable and the power cable from the rear of the optical drive Press the release button KW in the direction as shown and push the optical drive from the rear until it is projected from the front of the chassis Then hold the optical drive from the front and completely slide it out of the chassis Figure 55 Removing the optical drive 5 Touch the static protective package that contains the new optical drive to any unpainted surface on the outside of the server Then take the new optical drive and the signal cable out of the package Chapter 6 Installing removing or replacing hardware 117 6 Slide the new optical drive into the drive bay from the front until it snaps into position Note You do not need to remove the front bezel when replacing an optical drive However if you are adding a secondary optical drive in the upper optical drive bay you need to remove the front bezel first and then gain access to the protective shields to remove them The following illustration shows only the situation in which the front bezel has not been removed Figure 56 Installing the optical drive 7 Connect the a
3. Figure 79 Installing the non hot swap power supply assembly 11 Refer to your note and connect the new power supply assembly cables to the system board all drives and or hot swap hard disk drive backplane s depending on the model Then properly route the cables and secure the cables with the cable clips and ties in the chassis 12 Reinstall the front system fan s See Replacing the front system fan on page 149 13 If you are instructed to return the old non hot swap power supply assembly follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To complete the replacement go to Completing the parts replacement on page 168 Replacing a hot swap redundant power supply module Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 140 ThinkServer Hardware Maintenance Manual This topic provides instructions on how to replace a hot swap redundant power supply module This topic applies only to server models that come with hot swap redundant power supply module s For each hot swap redundant power supply module there might be one or two status LEDs on the power supply module near the power cord connector When the green LED is lit it indicates that the hot swap r
4. Figure 10 Front door lock Server components This topic provides information to help you locate the components of your server To remove the server cover and gain access to the inside of the server see Removing the server cover on page 85 The chassis configuration varies by model The following illustrations show the four main chassis configurations based on the supported hard disk drives Chapter 3 Product overview 25 The following illustration shows the components of the server with five to eight 3 5 inch hot swap hard disk drives f 22 M aR Figure 11 Components of the server with five to eight 3 5 inch hot swap hard disk drives DIT module available in some models Hard disk drive bay 0 Front panel Front system fan 1 EJ Optical drive bay 2 with an optical drive installed Front system fan 2 in some models Ell Optical drive bay 1 with an optical drive installed System board battery Hard disk drive bay 7 Expansion card Hard disk drive bay 2 Four memory slots installed memory modules vary by model Hard disk drive bay 1 e For more information about see Front view of the server on page 15 Note The DIT module Ell is only available in some models and the DIT panel also varies by model See DIT module on page 18 26 ThinkServer Hardware Maintenance M
5. packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To complete the removal procedure go to Completing the parts replacement on page 168 Installing or removing the DIT module This topic provides instructions on how to install or remove the DIT module The DIT module which is only available in some models provides diagnostic LEDs through the DIT panel to help you easily identify a problem The diagnostic LEDs on the DIT panel also vary depending on the installed power supply For more information see DIT module on page 18 Chapter 6 Installing removing or replacing hardware 111 Installing the DIT module Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to install the DIT module Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Depending on the model your server might look slightly different from the illustrations in this topic To install the DIT module do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server
6. Memory slots Your server system board provides four memory slots to support up to four memory modules For more information see Memory module installation rules on page 90 iButton socket Your server supports onboard SATA software RAID levels 0 1 and 10 However you can activate onboard SATA software RAID 5 by installing a ThinkServer SATA Software RAID 5 activation key in the iButton socket For more information see Installing or removing the ThinkServer SATA Software RAID 5 Key on page 102 Main power connector Used to connect the 24 pin P1 power connector of the power supply to provide main power to your server 5 system fan 2 connector Used to connect the cable of the upper front system fan front system fan 2 if your server model has two front system fans Microprocessor A microprocessor incorporates most or all of the functions of a computer s central processing unit CPU on a single integrated circuit The microprocessor for your server is secured in the microprocessor socket on the system board and a heat sink and fan assembly is installed above the microprocessor to provide cooling For more information about your microprocessor type see Features on page 7 Intel C202 chip The Intel C202 chip on the system board serves as a platform controller hub PCH which provides the data buffering and interface arbitration required to ensure that system interfaces operate efficiently and provides the b
7. pin Ell on the bracket with the corresponding holes the hard disk drive so that the hard disk drive can be seated in the bracket Note Do not touch the circuit board Ell on the bottom of the hard disk drive Figure 68 Installing the non hot swap hard disk drive into the bracket 9 Slide the new non hot swap hard disk drive with bracket into the drive bay until it snaps into position Chapter 6 Installing removing or replacing hardware 131 10 Connect the appropriate power cable and the SATA signal cable to the rear of the non hot swap hard disk drive Figure 69 Connecting cables to the rear of the non hot swap hard disk drive The following table provides information about the recommended power connector and system board SATA connector for the non hot swap hard disk drive installed in each drive bay See Server components on page 25 and System board components on page 42 for the location information about the hard disk drive bays and SATA connectors on the system board P9 power connector SATA connector 0 P10 power connector SATA connector 1 P7 power connector SATA connector 2 P8 power connector SATA connector 3 11 Connect the other end of the SATA signal cable to the appropriate SATA connector on the system board See System board components on page 42 12 Reinstall the front system fan 1 See Replacing the front system fan on page 149 132 ThinkServer Hardware Maintenance Manual
8. Exiting the Setup Utility program After you finish viewing or changing settings press Esc to return to the Setup Utility program main interface If you are on a nested submenu press Esc repeatedly until you reach the main interface Then you can do one of the following f you want to save the new settings and exit the Setup Utility program press F10 Otherwise your changes will not be saved f you do not want to save the new settings select Exit gt Discard Changes and Exit e f you want to return to the default settings press F9 or select Exit gt Load Default Values For more information about the Exit menu in the Setup Utility program see Exit menu on page 64 Updating or recovering the BIOS This topic provides instructions on how to update the BIOS and how to recover from a POST and BIOS update failure System programs are the basic layer of software built into your server System programs include the POST the UEFI BIOS the Setup Utility program and the BMC firmware The POST is a set of tests and procedures that are performed each time you turn on your server The UEFI BIOS is a layer of software that translates instructions from other layers of software into electrical signals that the server hardware can execute You can use the Setup Utility program to view or change the configuration settings of your server See Using the Setup Utility program on page 55 The BMC firmware works together with an iKVM key to
9. FYSA PFA 9 9 ASMA ASSE AS SACS Japan VCCI Class A compliance statement CORB 772AATBSRISM IB CH TORE EAE CRIT cREEtu amp ticdccm ausd coAS du Ru PY BOS WREBTSLIBKENSCEPHVWES Japan compliance statement for products which connect to the power mains with rated current less than or equal to 20 A per phase AROERERA 204 AT OMIM gt SRE RR El RS Se JIS C 61000 3 2 Am China Class A compliance statement AR IE WATS MATH ERMER Ht RAL SE 7 863806 Taiwan Class A compliance statement SAGAS LA PRR AR DS CER BE EFIE WRB T GAA Lenovo product service information for Taiwan amp 38 Lenovo mR fay B8 FE AB AR 0758 P BB 23 RT BRE ER 0800 000 702 2011 11 B 12 ERZ MEW 0800 666 975 2011 11 H 13 H EK 228 ThinkServer Hardware Maintenance Manual Index 2 5 inch hot swap hard disk drive backplane locations 37 3 5 inch hot swap hard disk drive backplane locations 35 A about RAID 72 Advanced menu Setup Utility program 57 advanced SATA or SAS hardware RAID configuring 79 ambient temperature over limit LED LED 19 BIOS and BMC firmware update software 13 BMC status LED 51 Boot Manager menu Setup Utility program 64 Boot Options menu Setup Utility program 62 cables connecting 38 configuring Ethernet controllers 80 server 55 configu
10. Turning on the server Turning off the server Chapter 5 Configuring the server Using the Setup Utility program Starting the Setup Utility program Viewing information in the ani Utility program A xus Setup Utility program Setting the system date and time Using passwords 5 Configuring the function Copyright Lenovo 2011 sN 0 N 12 12 12 13 13 13 13 13 13 15 17 18 19 22 25 32 33 34 42 46 50 53 53 53 55 55 55 55 56 64 65 66 Selecting a startup device Exiting the Setup Utility program Updating or recovering the BIOS Using the ThinkServer EasyStartup program Features of the ThinkServer program Starting the ThinkServer Easystartup program Configuring RAID About RAID RAID for your server Configuring RAID using the ThinkServer EasyStartup program Configuring the onboard SATA RAID Configuring the advalicod SATA or SAS hardware RAID e Configuring the Ethernet controllers Updating the firmware Using the Firmware Updater program Chapter 6 Installing removing or replacing hardware Guidelines Precautions Handling static sensitive devices System reliability guidelines ur Working inside the server with the power on Removing the server cover Removing and reinstalling the front Installing removing or replacing hardware Installing or removing a memory module Installing or re
11. 13 Align the top edge of the EMI protective panel with the top side of the hard disk drive cage and then pivot the EMI protective panel down until it snaps into position SN SY ES 5 amp Wess SS SS ES Been RSS Figure 70 Installing the EMI protective panel 14 Close and lock the front door What to do next To work with another piece of hardware go to the appropriate section To complete the installation go to Completing the parts replacement on page 168 Then you might need to reconfigure RAID for your server See Configuring RAID on page 71 Replacing the hot swap hard disk drive backplane Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to replace the hot swap hard disk drive backplane This topic applies only to server models that have hot swap hard disk drive s installed Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Depending on the model your server might look slightly different from the illustrations in this topic To replace the hot swap hard disk drive backplane do the following 1 Remove all media from the drives and turn
12. This topic provides some guidelines that you should read and understand before using your server Precautions Before you use the server be sure to read and understand the following precautions Before using the product be sure to read and understand the multilingual safety instructions and the Lenovo Limited Warranty LLW on the documentation DVD that comes with the product Reading and understanding the safety instructions reduces the risk of personal injury and damage to your product When you install your new server take the opportunity to download and apply the most recent firmware updates This step will help to ensure that any known issues are addressed and that your server is ready to function at maximum levels of performance To download firmware updates for your server do the following 1 Go to http support lenovo com 2 Click Download Drivers amp Software and follow the instructions on the Web page to download firmware updates for your server See Updating the firmware on page 80 for more information Before you install optional hardware devices make sure that the server is working correctly If the server is not working correctly see Chapter 7 Troubleshooting and diagnostics on page 171 to do basic troubleshooting If the problem cannot be solved see Chapter 9 Getting information help and service on page 213 Observe good housekeeping in the area where you are working Put removed covers and other
13. see Front view of the server on page 15 Note The DIT module Ell is only available in some models and the DIT panel also varies by model See DIT module on page 18 There is a 2 5 inch hot swap SAS hard disk drive or a dummy hard disk drive tray installed in each hard disk drive bay fito 28 ThinkServer Hardware Maintenance Manual Note The number of the installed hard disk drives varies by model For the vacant drive bay there is dummy hard disk drive tray to cover the place For information about the supported expansion card see System board components on page 42 Depending on the model your server might come with a screw secured non hot swap power supply or hot swap redundant power supply module s For more information about the memory modules see Memory module installation rules on page 90 The following illustration shows the components of the server with up to four 3 5 inch hot swap hard disk drives 1 g 217 LFS Figure 13 Components of the server with up to four 3 5 inch hot swap hard disk drives DIT module available in some models El Front system fan 1 H Front panel System board battery Ell Optical drive bay 2 with an optical drive installed Expansion card varies by model in some models ll Optical drive bay 1 with an optical drive install
14. 110 11G MT 0441 130 13G Microprocessor Core 13 2120 3 3 GHz dual core 3 65 W 1 GT 1333 MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03T8010 2 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Chapter 8 FRU lists 187 System board 5 31000 system board MT 0387 CTO 11U 11G 12U 12G MT 0388 CTO 11U 12U 12G 13U 13G 14U MT 0389 CTO 11U MT 0390 CTO 11U 11G 12U 12G 13U 13G 03X3665 MT 0391 CTO 11U MT 0392 CTO 11U 12U 13U 14U 15U MT 0393 CTO 11U 11G 12U 12G MT 0441 CTO 11U 11G 12U 12G 13U 13G 14U 14G 15U 15G 16U 16G System fan assembly MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 46U3197 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models System fan assembly e MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3948 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models Power supply GPS 400CB 400 W power supply REV 00F MT 0387 CTO 11U 11G 12U 12G MT 0388 CTO 11U 12U 12G 13U 13G 14U MT 0389 CTO 11U MT 0390 CTO 11U 11G 12U 12G 13U 13G 03X3800 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO 188 ThinkServer Hardware Maintenance Manual Power distribution board and cage assembly REV 00 for redundant power supplies MT 0387 CTO MT 0388 CTO MT 0389 CTO
15. Locate the memory slots on the system board See System board components on page 42 a A WwW nm Remove any parts or disconnect any cables that might prevent your access to the memory slots 92 ThinkServer Hardware Maintenance Manual 6 Locate the appropriate memory module that you want to remove and open the retaining clips on both ends of the memory slot Then grasp the memory module by its edges and carefully pull it straight up to remove it from the memory slot Figure 39 Removing a memory module 7 If you are instructed to return the old memory module follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To complete the removal procedure go to Completing the parts replacement on page 168 Installing or removing a PCI card This topic provides instructions on how to install or remove a PCI card The EMI integrity and cooling of the server are protected by having all drive bays and PCI card slots covered or occupied When you install an internal drive or PCI card save the EMI shield or drive bay filler from the drive bay or save the PCI card slot bracket in the event that you later remove the device Attention An unoccupied drive bay or PCI card slot without cover shield filler or any other protection might impact the EMI integrity and cooling of the se
16. MT 0390 CTO MT 0391 CTO 11U MT 0392 CTO 11U 12U 13U 14U 15U MT 0393 CTO 11U 11G 12U 12G MT 0441 CTO 11U 11G 12U 12G 13U 13G 14U 14G 15U 15G 16U 16G Power supply redundant 450 W power supply module REV 00 MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3801 1 MT 0391 CTO 11U MT 0392 CTO 11U 12U 13U 14U 15U MT 0393 CTO 11U 11G 12U 12G MT 0441 CTO 11U 11G 12U 12G 13U 13G 14U 14G 15U 15G 16U 16G Memory module 2 GB 1RX8 PC3 10600E ECC UDIMM DDR3 1333 2 Gbit MT 0387 CTO 11U 11G 12U 12G MT 0388 CTO 11U 12U 12G 13U 13G 14U MT 0389 CTO 11U MT 0390 CTO 11U 11G 12U 12G 13U 13G 03X3660 MT 0391 CTO 11U MT 0392 CTO 11U 12U 13U 14U 15U MT 0393 CTO 11U 11G MT 0441 CTO 13U 13G Memory module 4 GB 2RX8 PC3 10600E ECC UDIMM DDR3 1333 2 Gbit MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3661 MT 0391 CTO MT 0392 CTO MT 0393 CTO 12U 12G MT 0441 CTO 11U 11G 12U 12G 14U 14G 15U 15G 16U 16G Mechanical FRUs The FRUs listed in the following table are not illustrated Chapter 8 FRU lists 189 3 5 inch hot swap hard disk drive tray V2 0 MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3835 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models 3 5 inch non hot swap hard disk drive tray V2 0 MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models
17. www lenovo com lenovo environment WEEE Y Z7IX EU 86 3 2528 3 IORI EU BAIS ZRERET HERES 2002 96 EC WEEE 05 xd COBB EU 218859 ZH ER OD Bl 4 VHS 2 92 IOFAN ME 95 5r CES WEEE 940481 Annex IV EJZ KY 5 dnt ESET EEE WASTE amp 0005823 3 d S C Sl El in KEI BENSASMRMRRPAARK SZ STHREOIRA US 2JU SAUICSBEDEOORMMAKEAARLEITHIEGY ELA WEEE DENIS OTI Http www lenovo com enovo env i ronment To WEEE Waste Electrical and Electronic Equipment xpnoiporroig rai u vo Evwons kai NopBnyia cuoKeu g TOTTOBETOUVTAI ETIKETEG TTOU TNV ATTOPPIWN NAEKTPIKWV KAI NAEKTPOVIKWV pe Eupwtraikh O ny a 2002 96 EC Odnyia auth yia Trjv KAI TNV AVAKUKAWON XPNOIMOTIOINUEVWV OUOKEUU JV TOU IOX EI GAN TNV Eupurraikr Evwon etik ta rorroOere rai did opa rrpoi vra yia va ro TEPUATIONO TNS xprjong rou ro rrpoi v ue O ny a 1 Ol xprjoreg NAEKTPIKWV Kar NAEKTPIKWV e
18. 2 7a 0 2 5 B 2 Bet G Figure 107 Component locations Major FRUs The following replaceable components are available for machine types MTs 0387 0388 0389 0390 0391 0392 0393 and 0441 Copyright Lenovo 2011 179 DIT kit without label MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3668 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO 5U front panel kit for LX KT2 v1 1 MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3573 2 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models Optical drive DVD ROM drive 16x 48x SATA e MT 0387 CTO 11U 11G 12U 12G MT 0388 CTO 11U 12U 12G 13U 13G 14U MT 0389 CTO 11U MT 0390 CTO 71 5543 1 0391 110 MT 0392 CTO 110 120 130 140 150 0393 0441 Optical drive DVD Burner CD RW Rambo 8 SATA MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 11U 11G 12U 12G 13U 13G 71 5545 1 0391 0392 MT 0393 110 11 120 12G MT 0441 CTO 11U 11G 12U 12G 130 136 14U 14G 15U 15G 16U 16G 180 ThinkServer Hardware Maintenance Manual Lenovo RDX USB drive bundle bay MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 67Y1424 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Lenovo 160 GB RDX U
19. CTO MT 0390 CTO 03 3777 1 0391 0392 0393 0441 Microsoft Windows Small Business Server 2011 Standard Edition French MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3778 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microsoft Windows Small Business Server 2011 Standard Edition German MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03 3779 0391 0392 0393 0441 Microsoft Windows Small Business Server 2011 Standard Edition Japanese MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3780 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO 206 ThinkServer Hardware Maintenance Manual Shipgroup FRU number CRU Microsoft Windows Small Business Server 2011 Premium Add on English MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3781 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microsoft Windows Small Business Server 2011 Premium Add on French MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3782 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microsoft Windows Small Business Server 2011 Premium Add on German MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3783 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microsoft Windows Small Business Server 2011 Premium Add on Japanese MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390
20. Ell Memory slot 4 DIMMB2 EJ Memory slot 2 DIMMA2 Memory slot 3 DIMMB1 Memory slot 1 DIMMA1 The following table provides information about the memory module installation rules that you should consider when installing or removing a memory module The X mark indicates the memory slot s into which the memory module s should be installed in different situations The numbers 1 2 3 and 4 indicate the installation sequence Note The installed memory modules must be the same type with the same voltage and frequency One UDIMM Three UDIMMs Four UDIMMs Cae ee ho E 90 ThinkServer Hardware Maintenance Manual Installing a memory module Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to install a memory module Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Notes 1 To optimize system performance make sure that you consider and follow the memory module installation rules when performing the operation See Memory module installation rules on page 90 2 Use any documentation that comes with the memory module and follow those instructions in addition to the instructions in this topic To install a memory
21. Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to install or replace an optical drive The EMI integrity and cooling of the server are protected by having all drive bays covered or occupied Your server has two optical drive bays If only one optical drive is installed in the lower bay the upper bay is covered by a metal EMI shield on the chassis and also a plastic shield on the front bezel When you install a secondary optical drive or a RDX USB drive bundle save the removed EMI shield from the chassis and plastic shield from the front bezel in the event that you later remove the drive and need the shields to cover the drive bay Attention An unoccupied drive bay without any other protection might impact the EMI integrity and cooling of the server which might result in overheating or component damage To maintain the EMI integrity and cooling of the server install a new optical drive as soon as you remove the failing one or the protective shields CAUTION When laser products such as CD ROMs DVD drives fiber optic devices or transmitters are installed note the following Do not remove the covers Removing the covers of the laser product could result in exposure to hazardous laser radiation There are no serviceable parts inside the device Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exp
22. See Installing a PCI card on page 93 9 Dispose of the old system board battery as required by local ordinances or regulations What to do next To work with another piece of hardware go to the appropriate section To complete the replacement go to Completing the parts replacement on page 168 After you replace the system board battery you must reset passwords reset system date and time and reconfigure the server See Chapter 5 Configuring the server on page 55 Replacing the system board Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to replace the system board CAUTION Hazardous moving parts Keep fingers and other body parts away 162 ThinkServer Hardware Maintenance Manual CAUTION A A The heat sink and microprocessor might be very hot Turn off the server and wait three to five minutes to let the server cool before removing the server cover Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference To replace the system board do the following 1 A OO N Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server Remove
23. See Removing the server cover on page 85 3 Lay the server on its side for easier operation 4 Touch the static protective package that contains the TPM module to any unpainted surface on the outside of the server Then take the TPM module out of the package Note Carefully handle the TPM module by its edges Chapter 6 Installing removing or replacing hardware 109 5 Locate the TPM connector on the system board and then insert the TPM module into the TPM connector m SS SSS D 5 E E Figure 49 Installing the TPM module What to do next To work with another piece of hardware go to the appropriate section To complete the installation go to Completing the parts replacement on page 168 Then you can configure the TPM function in the Setup Utility program See Configuring the TPM function on page 66 Removing the TPM module Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to remove the TPM module if the se
24. The supported RAID levels RAID 0 1 and 10 To activate RAID 5 and 50 levels you need to install a RAID 5 key on the RAID card See Installing or removing the ThinkServer 9240 8i RAID 5 Upgrade Key on page 100 For detailed information see Configuring the advanced SATA or SAS hardware RAID on page 79 Note The ThinkServer EasyStartup program simplifies the process of configuring supported RAID and installing supported operating systems and device drivers Chapter 5 Configuring the server 73 Before configuring RAID for your server observe the following precautions 1 Use hard disk drives that have the same capacity within a single RAID array 2 Use hard disk drives that are of the same type SATA or SAS within a single RAID array 3 Depending on the operating system the primary RAID might be limited to 2 TB total drive capacity Configuring RAID using the ThinkServer EasyStartup program The ThinkServer EasyStartup program simplifies the process of configuring supported RAID and installing supported Windows and Linux operating systems and device drivers on your server The user guide for the program can be accessed directly from the program interface The ThinkServer EasyStartup program has the following features for RAID configuration For use with all supported RAID controllers Automatically detects hardware and lists all supported RAID configurations e Configures one or more disk arrays per controller depending
25. a Partially remove screw El then completely remove screw then return to screw completely remove it b Partially remove screw then completely remove screw EM and then return to screw completely remove it Note The four screws are integrated parts of the heat sink and fan assembly Do not try to remove the four screws from the heat sink and fan assembly Figure 90 Removing the screws that secure the heat sink fan assembly 7 Gently twist the heat sink and fan assembly to free it from the microprocessor and then lift the heat sink and fan assembly off the system board 8 Lay aside the old heat sink and fan assembly Touch the static protective package that contains the new heat sink and fan assembly to any unpainted surface on the outside of the server Then remove the new heat sink and fan assembly from the package Note When handling the heat sink and fan assembly do not touch the thermal grease on the bottom of it 9 Place the new heat sink and fan assembly on the system board so that the f
26. equipment to responsibly recycle their equipment when it is no longer needed Lenovo offers a variety of programs and services to assist equipment owners in recycling their IT products For information on recycling Lenovo products go to http www lenovo com recycling 218 ThinkServer Hardware Maintenance Manual US 5 LT RU ER Tm LY ERR E Hid dE AUI Heim EORR ER EAE HIS HEUZ FoWERHVEST EK CIERRE BUR GERE ROE HAJ YARE LUBA 6415 HRV IL H ERA SHR L TOES MIX http www lenovo com recycling japan 2 8 lt 72 amp U MATEY ZEEC ERRARLAOEASUALOX A2 SI 2003 10H 1 B amp 17 A kUzEL 7 http www lenovo com recycling japan C88 lt amp M EE SEE eSOCA AB TORREZ OUT 21 RRE MEO ESI MCE ben co 39 bid allg U 5 4 7 I246Eo CRESELC C ESL Collecting and recycling a disused Lenovo computer or monitor If you are a company employee and need to dispose of a Lenovo computer or monitor that is the property of the company you must do so in accordance with the Law for Promotion of Effective Utilization of Resources Computers and monitors are categorized as industrial waste and should be properly disposed of by an industrial waste disposal contractor certified by a local government In
27. hereinafter referred to as the RAID card The following illustration shows the connectors on the RAID card Figure 17 ThinkServer 9240 8i RAID 0 1 Adapter Port 0 5 key connector B Port 1 E External connector El Port o Used to connect a mini SAS signal cable See Connecting cables on page 38 Port 1 Used to connect a mini SAS signal cable See Connecting cables on page 38 E RAID 5 key connector Used to connect a ThinkServer 9240 8i RAID 5 Upgrade Key See Installing or removing the ThinkServer 9240 8i RAID 5 Upgrade Key on page 100 External connector Used to connect a 2 pin 200 mm 7 87 inches RAID card to system board hard disk drive LED cable See Connecting cables on page 38 Hot swap hard disk drive backplane Your server supports the following hot swap hard disk drive and backplane configurations Five to eight 3 5 inch hot swap SATA or SAS hard disk drives with two backplanes e Up to four 3 5 inch hot swap SATA or SAS hard disk drives with one backplane 34 ThinkServer Hardware Maintenance Manual Up to eight 2 5 inch hot swap SAS hard disk drives with one backplane The following illustration shows the locations of the hot swap hard disk drive backplanes You need to open the server cover and remove the front system fans to access the backplanes See Removing the server cover on page 85 and Replacing the front system fan on page 149 Notes 1 Depending on the model your s
28. ndern der Europ ischen Union und in Norwegen Ger te werden gem der Richtlinie 2002 96 EC der Europ ischen Union ber Elektro und Elektronikaltger te WEEE gekennzeichnet Die Richtlinie regelt die R ckgabe und Wiederverwertung von Altgeraten innerhalb der Europ ischen Union Mit dieser Kennzeichnung versehene Altger te d rfen gem dieser Richtlinie nicht weggeworfen werden sondern m ssen zur ckgegeben werden Anwender von Elektro und Elektronikgeraten mit der WEEE Kennzeichnung d rfen diese Annex IV der WEEE Richtlinie nach ihrem Gebrauch nicht als allgemeinen Hausm ll entsorgen Stattdessen m ssen diese Ger te im verf gbaren Sammelsystem zur ckgegeben werden und damit einem Recycling oder Wiederherstellungsprozess zugef hrt werden bei dem m gliche Auswirkungen der Ger te auf die Umwelt und den menschlichen Organismus aufgrund gef hrlicher Substanzen minimiert werden Weitere Informationen zur Entsorgung von Elektro und Elektronikaltgeraten finden Sie unter der Adresse http www lenovo com lenovo environment La marca de Residuos de equipos el ctricos y electr nicos WEEE se aplica s lo a los pa ses pertenecientes a la Uni n Europea UE y a Noruega Los aparatos se etiquetan conforme a la Directiva Europea 2002 96 EC relativa a los residuos de equipos el ctricos y electr nicos WEEE La directiva determina el marco para devolver y reciclar los aparatos usados seg n sea aplicable en toda la Uni n E
29. on page iii and Guidelines on page 83 This topic provides instructions on how to replace the front panel board assembly Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Depending on the model your server might look slightly different from the illustrations in this topic To replace the front panel board assembly do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server Remove the server cover See Removing the server cover on page 85 Remove the front bezel See Removing and reinstalling the front bezel on page 87 Locate the front panel See Front panel on page 17 Remove the front system fan s See Replacing the front system fan on page 149 o 0 KR OQ Im Disconnect the signal cables of the front panel board assembly from the internal dual port USB 2 0 connector 1 and the front panel connector on the system board See System board components on page 42 7 If necessary remove any parts or disconnect any cables that might impede your access to the signal cables of the front panel board assembly Note down the cable routing and then release the signal cables of the front panel board assembly from any cable clips or ties in the chassis Chapter 6 I
30. setting hot spare drive 77 setting changing deleting password 65 Setup Utility program exiting 67 interface 56 password 65 starting 55 TPM 66 using 55 software 12 specifications 12 starting LSI Software RAID Configuration Utility program 74 Setup Utility program 55 ThinkServer EasyStartup program 70 startup device selecting 66 Setup Utility program 66 static sensitive devices guidelines 84 static sensitive devices handling 84 system board 42 LED 50 replacing 162 system board battery replacing 161 system board components locations 42 system board hardware fault LED 50 system board jumpers locations 46 system board LEDs locations 50 system board RAID 5 key installing 102 removing 104 232 ThinkServer Hardware Maintenance Manual System date setting 64 System event log troubleshooting and diagnostics 172 System reliability guidelines 84 System status LED 18 System time setting 64 T the BIOS flashing 68 recovering 68 updating 68 updating or recovering 67 the BIOS update utility program downloading 67 ThinkServer EasyStartup software 12 ThinkServer EasyStartup program features 70 starting 70 using 69 ThinkServer EasyUpdate Firmware Updater software 13 ThinkServer Web address 1 TPM Setup Utility program 66 TPM module installing 109 removing 110 troubleshooting and diagnostics hard disk drive problems 174 keyboard mouse or USB device problems 176 memory module problems 176 opti
31. 0441 CTO Microsoft Windows Server 2008 R2 Enterprise Edition 64 bit Italian MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 90Y1195 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microsoft Windows Server 2008 R2 Enterprise Edition 64 bit Spanish MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 90Y1197 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Chapter 8 FRU lists 211 Shipgroup FRU number CRU Microsoft Windows Server 2008 R2 Enterprise Edition 64 bit Turkish MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 90Y1198 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Reseller Option Kit ROK Microsoft Windows Server 2008 Foundations 64 bit multilingual English Japanese MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO SENTIS MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO ROK Microsoft Windows Server 2008 Foundations 64 bit multilingual English French German Italian Spanish MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 0391 0392 0393 0441 212 ThinkServer Hardware Maintenance Manual Chapter 9 Getting information help and service This chapter contains information about help service and technical assistance for products manufactured by Lenovo and where to go for additional information about Lenovo and Lenovo products Information resources You
32. 15G 16U 16G Chapter 8 FRU lists 185 Heat sink MT 0387 MT 0388 MT 0389 MT 0390 03 3710 0391 0392 0393 0441 Microprocessor Xeon quad core E31280 8 3 5 GHz 95 W MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3624 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microprocessor Xeon quad core E31220 8 3 1 GHz 80 W MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 11U 11G 12U 12G 03 3625 0391 0392 MT 0393 120 129 MT 0441 110 11 Microprocessor Xeon quad core 31230 8 3 2 GHz 80 W MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3626 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO 14U 14G 186 ThinkServer Hardware Maintenance Manual Microprocessor Xeon quad core E31240 8 3 3 GHz 80 W MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3627 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO 12U 12G 16U 16G Microprocessor Xeon quad core E31270 8 MB 3 4 GHz 80 W MT 0387 CTO MT 0388 CTO MT 0389 CTO 11U MT 0390 CTO 03X3628 2 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO 15U 15G Microprocessor Core i3 2100 3 1 GHz dual core 65 W 1 GT 1333 MT 0387 CTO 11U 11G 12U 12G MT 0388 CTO 11U 12U 12G 13U 13G 14U MT 0389 CTO 11U MT 0390 CTO 13U 13G 0378011 2 0391 110 0392 110 120 130 140 150 MT 0393
33. 204 213 213 213 213 213 214 214 214 215 215 217 218 218 218 218 219 220 220 221 224 225 225 226 226 226 229 Safety information Note Before using the product be sure to read and understand the multilingual safety instructions on the documentation DVD that comes with the product pda Aa sig GLY del Cpe 265 tl Gl uiu ul DVD oa u 55 yl Antes de usar o produto leia e entenda as instru es de seguran a multil ngues no DVD de documenta o que o acompanha na B DVD ce Prije upotrebe ovog proizvoda obavezno proCitajte viSejezi ne sigurnosne upute koje nalaze DVD u s dokumentacijom koji dobivate uz proizvod P ed pou it m produktu je treba si p e st a porozum t bezpe nostn m pokyn m uveden m na disku DVD s dokumentac ktery je dod v n s produktem For du bruger produktet skal du serge for at leese og forsta de sikkerhedsforskrifter der findes flere sprog p den dokumentations dvd der felger med produktet Lue tuotteen mukana toimitetulla DVD tietolevylla olevat monikieliset turvaohjeet ennen
34. CAUTION Hazardous moving parts Keep fingers and other body parts away CAUTION Never remove the cover on a power supply or any part that has the following label attached Hazardous voltage current and energy levels are present inside any component that has this label attached There are no serviceable parts inside these components If you suspect a problem with one of these parts contact a service technician Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Depending on the model your server might look slightly different from the illustrations in this topic To replace the non hot swap power supply assembly do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 3 Lay the server on its side for easier operation 4 Remove the front system fan s See Replacing the front system fan on page 149 Chapter 6 Installing removing or replacing hardware 137 5 Note down the cable routing and connection Then disconnect the power supply assembly cables from the system board and all drives For server models with hot swap hard disk drives you also need to disconnect the power cable s from the hot swap har
35. CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microsoft Windows Server 2008 R2 Standard Edition 64 bit Italian MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 90Y1188 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Chapter 8 FRU lists 209 Microsoft Windows Server 2008 R2 Standard Edition 64 bit Turkish MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 90Y1189 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microsoft Windows Server 2008 R2 Standard Edition 64 bit Dutch MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 90Y1190 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microsoft Windows Server 2008 R2 Enterprise Edition 64 bit English MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 90Y1191 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microsoft Windows Server 2008 R2 Enterprise Edition 64 bit Dutch MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 90Y1192 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO 210 ThinkServer Hardware Maintenance Manual Shipgroup FRU number CRU Microsoft Windows Server 2008 R2 Enterprise Edition 64 bit French MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 90Y1193 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microsoft Windows Server 2008 R2 Enterprise Edition 64 bit German MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 90Y1194 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT
36. CTO 12G 13G MT 0389 CTO 11G MT 0390 CTO 11G 12G 13G 41R3236 MT 0391 CTO MT 0392 CTO MT 0393 CTO 11G 12G MT 0441 CTO 11G 12G 13G 14G 15G 16G Power cord South Africa MT 0387 CTO 11G 12G MT 0388 CTO 12G 13G MT 0389 CTO 11G MT 0390 CTO 11G 12G 13G 41R3220 MT 0391 CTO MT 0392 CTO MT 0393 CTO 11G 12G MT 0441 CTO 11G 12G 13G 14G 15G 16G Power cord i MT 0387 MT 0388 MT 0389 MT 0390 41R3341 MT 0391 MT 0392 MT 0393 MT 0441 Shipgroup The Lenovo shipgroup for a specific country or region is usually available only in that country or region 204 ThinkServer Hardware Maintenance Manual po Shipgroup FRU mer Documentation DVD English MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3656 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Documentation DVD multilingual MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3658 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO EasyStartup DVD multilingual MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3946 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microsoft Windows Server 2008 R2 64 bit shipgroup US MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 90Y1183 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Chapter 8 FRU lists 205 Shipgroup FRU number Microsoft Windows Small Business Server 2011 Standard Edition English MT 0387 CTO MT 0388 CTO MT 0389
37. Firmware Updater program 3 Download the ISO image for the Firmware Updater program and the installation instructions in a TXT file 4 Use any CD or DVD burning software to create a bootable disc with the ISO image 5 Print the TXT file that contains the installation instructions and follow the instructions to use the Firmware Updater program to update your system firmware Notes 1 Before distributing the firmware updates to a server ensure that your server can restart successfully without encountering hardware problems 2 f you have updated the BIOS firmware all the BIOS settings become the default settings of the updated BIOS version You need to check and reconfigure the BIOS settings for your specific needs Chapter 5 Configuring the server 81 82 ThinkServer Hardware Maintenance Manual Chapter 6 Installing removing or replacing hardware This chapter provides instructions on how to install remove or replace hardware for your server This chapter contains the following items e Guidelines on page 83 e Removing the server cover on page 85 e Removing and reinstalling the front bezel on page 87 e Installing removing or replacing hardware on page 89 e Completing the parts replacement on page 168 For a list of the ThinkServer options go to http www lenovo com thinkserver Click the Products tab and then click Options to view the supported server option information Guidelines
38. GmbH Gropiusplatz 10 D 70563 Stuttgart Informationen in Hinsicht EMVG Paragraf 4 Abs 1 4 Das Ger t erf llt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse A Nach der EN 55022 Dies ist eine Einrichtung der Klasse A Diese Einrichtung kann im Wohnbereich Funkst rungen verursachen in diesem Fall kann vom Betreiber verlangt werden angemessene MaBnahmen durchzuf hren und daf r aufzukommen Appendix A Notices 227 Nach dem Gerate d rfen an Orten f r die sie nicht ausreichend entst rt sind nur mit besonderer Genehmigung des Bundesministers f r Post und Telekommunikation oder des Bundesamtes f r Post und Telekommunikation betrieben werden Die Genehmigung wird erteilt wenn keine elektromagnetischen St rungen zu erwarten sind Auszug aus dem EMVG Paragraph 3 Abs 4 Dieses Genehmigungsverfahren ist nach Paragraph 9 EMVG in Verbindung mit der entsprechenden Kostenverordnung Amtsblatt 14 93 kostenpflichtig Anmerkung Um die Einhaltung des EMVG sicherzustellen sind die Ger te wie in den Handb chern angegeben zu installieren und zu betreiben Australia and New Zealand Class A statement Attention This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Korea Class A compliance statement OIE SSSAS 2 2 1 BOA LE ASHE 0 SS AS 212 82 S S S82 AM E OH AH
39. J 100003 for indirect connection to public telecommunication systems in the United Kingdom 220 ThinkServer Hardware Maintenance Manual European Union Compliance to the Electromagnetic Compatibility Directive This product is in conformity with the protection requirements of EU Council Directive 2004 108 EC on the approximation of the laws of the Member States relating to electromagnetic compatibility Lenovo cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non recommended modification of the product including the installation of option cards from other manufacturers This product has been tested and found to comply with the limits for Class A Information Technology Equipment according to European Standard EN 55022 The limits for Class A equipment were derived for commercial and industrial environments to provide reasonable protection against interference with licensed communication equipment Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures German Class A compliance statement Deutschsprachiger EU Hinweis Hinweis f r Ger te der Klasse A EU Richtlinie zur Elektromagnetischen Vertraglichkeit Dieses Produkt entspricht den Schutzanforderungen der EU Richtlinie 2004 108 EG fr her 89 336 EWG zur Angleichung der Rechtsvorschriften ber die elektromagnetische Ve
40. LED 18 hardware installing 83 removing 83 replacing 83 heat sink and fan assembly replacing 154 help getting 213 hot spare drive setting 77 hot swap hard disk drive installing 119 replacing 119 hot swap hard disk drive backplane locations 34 replacing 133 hot swap hard disk drive status LED 32 hot swap hard disk drive status LEDs locations 32 hot swap redundant power supply module replacing 140 hot swap redundant power supply module status LED 21 iKVM key installing 106 removing 107 information getting 213 initializing virtual drive 77 Input Output 1 features 9 installation rules DIMM 90 memory module 90 installing DIMM 91 DIT module 112 Ethernet card 96 hardware 83 hot swap hard disk drive 119 230 ThinkServer Hardware Maintenance Manual iKVM key 106 memory module 91 non hot swap hard disk drive 128 optical drive 115 PCI card 93 RAID 5 key on the RAID card 100 RAID card 98 server cover 168 system board RAID 5 key 102 TPM module 109 installing and using MegaRAID Storage Manager program 79 interface LSI Software RAID Configuration Utility program 75 Setup Utility program 56 internal drives features 9 L LED ambient temperature over limit LED 19 BMC status 51 DIT panel 18 error 19 Ethernet status 22 front panel 17 hard disk drive status 18 hot swap hard disk drive status 32 hot swap redundant power supply module status 21 NIC status 18 optical drive status 16 POST code diagn
41. Note Carefully save the front door key to avoid loss Server locks Locking the server cover helps prevent unauthorized access to the inside of your server and locking the front door helps prevent unauthorized access to the installed hard disk drives Note Depending on the model your server might look slightly different from the illustrations in this topic 22 ThinkServer Hardware Maintenance Manual Padlock Your server comes with a padlock loop so that the server cover cannot be removed when a padlock is installed Figure 8 Padlock Chapter 3 Product overview 23 Integrated cable lock An integrated cable lock sometimes referred to as the Kensington lock can be used to secure your server to a non permanent fixture The cable lock attaches to the integrated cable lock slot at the rear of your server and is operated with a key The cable lock also locks the server cover This is the same type of lock used with many notebook computers You can order an integrated cable lock directly from Lenovo by searching for Kensington at http support lenovo com Figure 9 Integrated cable lock 24 ThinkServer Hardware Maintenance Manual Front door lock You can remove the key attached on the server and use it to open or lock the front door of the server The front door helps protect the hard disk drive cages to prevent unauthorized access to the installed hard disk drives
42. Priority Varies depending on the available Specify the startup priority for all the hard disk drives available hard disk drives Optical Disk Drive Priority Varies depending on the available Specify the startup priority for all the optical drives available optical drives Removable Device Priority Varies depending on the available Specify the startup priority for all the removable devices available removable devices Network Device Priority Varies depending on the available Specify the startup priority for all the network devices available network devices Quiet Boot Disabled Enable or disable the quiet boot Enabled feature to determine whether the logo screen will be displayed or not when starting the server Chapter 5 Configuring the server 63 _ Memuitem Selections Comments Bootup Num Lock On Turn the Num Lock key on or off Off POST Error Pause Disabled Enable or disable the POST error e Enabled pause feature When this feature is set to Enabled the system will stop on the POST screen if any error occurs during the POST Boot Manager menu This topic provides information about the Boot Manager menu in the Setup Utility program The Boot Manager menu lists all the bootable devices installed on your server system board and the items listed vary depending on your server configuration and installed option devices If you select a desired device listed on this menu the server will start from the device you
43. Remove the server cover See Removing the server cover on page 85 Remove the front bezel See Removing and reinstalling the front bezel on page 87 Touch the static protective package that contains the DIT module to any unpainted surface on the outside of the server Then take the DIT module out of the package 5 Connect the signal cable to the rear of the DIT module 6 Route the signal cable of the DIT module through the corresponding hole in the chassis and position the DIT module on the chassis so that the screw hole in the DIT module is aligned with the corresponding screw hole Ell in the chassis Then install the screw to secure the DIT module in place i Mp Zp Z NN Figure 51 Installing the DIT module 7 Remove the front system fan s See Replacing the front system fan on page 149 112 ThinkServer Hardware Maintenance Manual 8 Connect the other end of the signal cable to the DIT module connector on the system board See System board components on page 42 Then properly route the signal cable of the DIT module You might need to secure the signal cable with cable clips or ties in the chassis Figure 52 Cable routing 9 Reinstall the front system fan s See Replacing the front system fan on page 149 10 Reinstall the front bezel See Removing and reinstalling the front bezel on page
44. Using the diagnostic program Viewing the system event log Basic troubleshooting tables ThinkServer program problems Optical drive problems Hard disk drive problems Memory module problems 367 Keyboard mouse or USB device POST error codes Chapter 8 FRU lists Major FRUs Mechanical FRUs ii ThinkServer Hardware Maintenance Manual 133 137 140 143 147 149 152 154 157 161 162 168 168 170 171 171 171 172 172 172 172 173 174 176 176 177 179 179 189 Adapters and miscellaneous FRUs Power cords Shipgroup Chapter 9 Getting information ue and service Information resources Using the documentation ThinkServer Web site http www lenovo com thinkserver Lenovo Support Web site Help and service Before you call Calling for service Using other services Purchasing additional services Appendix A Notices Trademarks Important notes Polyvinyl Chloride PVC cable an P notice Recycling information Battery return program Requirement for batteries containing perchlorate Particulate contamination Important information for the European Directive 2002 96 EC Restriction of Hazardous Gubstancas Directive RoHS China RoHS Turkish statement of mpbiiah s German Ordinance for Work gloss statement Electronic emission notices Federal Communications Gommission FCC Statement Index 194 196
45. amp aprnp rov electrical and electronic equipment trou p pouv ro WEEE pe ro Napdptnua IV v OSnyiac va arropp rrrouv amp amp aprrjuara QAA va xpnoiporroiov ro SIGBEOINO TNV ETTIOTPOMH AVAKUKAWON KAI av krrnor TWV pe OKOTTO TNV SUVNTIKWV rrepiB AAov kai THY avOpurrrivr uye a amp arr ag rrapouo ag OUCIWV ora OXETIK pE KATGAANAES OUAAOYIS KAI Karepyao ag NAEKTPOVIKWV OUOKEUWV KAI Gaprnp TUV rriokKeqOe re tnv http www lenovo com lenovo environment A WEEE leselejtezett elektromos s elektronikus berendez sek jelz s csak az EU tag llamaira s Norv gi ra vonatkozik A berendez sek a leselejtezett elektromos s elektronikus berendez sekre WEEE vonatkoz 2002 96 EC sz m EU direkt v nak val megfelel st tan s t c mk vel vannak ell tva A direkt va a haszn lt berendez sek visszav tel nek s jrahasznos t s nak keretrendszer t hat rozza meg az Eur pai Uni n bel l A k l nb z term keken l that c mke azt jelenti hogy a term ket az lettartam nak v g n nem szabad kidobni hanem direkt v nak megfelel en kell visszanyerni
46. are erased and the BIOS recovers to the factory default settings To clear CMOS do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 48 ThinkServer Hardware Maintenance Manual 3 Lay the server on its side for easier operation 4 Locate the Clear CMOS Recovery jumper on the system board and then move the jumper from the default normal position pin 1 and pin 2 to the short circuited position pin 2 and pin 3 5 Wait more than 10 seconds and then move the Clear CMOS Recovery jumper back to the normal position pin 1 and pin 2 6 Reinstall the server cover and connect the power cord s See Completing the parts replacement on page 168 7 Wait about 30 seconds Then turn on the server The BIOS passwords are erased and the BIOS recovers to the factory default settings El BMC setting jumper When the BMC setting jumper is in the default normal position pin 1 and pin 2 the server needs about 30 seconds for the BMC to initialize whenever you connect the server to an ac power source If you press the power switch on the front panel during this period the server will not start immediately it will start after the BMC initialization finishes If you move the BMC setting jumper t
47. backplane and the system board refer to the related topics in Locations on page 13 For information about connecting the appropriate power connector of the power supply to the backplane see Hot swap hard disk drive backplane on page 34 Server models with up to eight 2 5 inch SAS hot swap hard disk drives and one backplane For server models with up to eight 2 5 inch SAS hot swap hard disk drives and one backplane a required RAID card must be installed in the server The following cables that come with the RAID card are required Note The option package for the RAID card is designed for different types of servers and might contain additional cables that are not required to be installed into your server One or two 700 mm 27 56 inches mini SAS to mini SAS signal cables depending on the number of the hard disk drives installed One 2 pin 200 mm 7 87 inches RAID card to system board hard disk drive LED cable Chapter 3 Product overviev 39 Use the following instructions to connect the cables 1 Use one 700 mm 27 56 inches mini SAS to mini SAS signal cable Connect the mini SAS connector to the port 0 on the RAID card Then connect the mini SAS connector to the mini SAS signal cable connector 1 on the 2 5 inch hot swap hard disk drive backplane 2 If you have more than four 2 5 inch hard disk drives installed use the other 700 mm 27 56 inches mini SAS to mini SAS signal cable Connect the mini SAS connecto
48. can use the information in this topic to access useful resources relating to your needs when using the product Using the documentation Information about your Lenovo system and installed software if any or optional device is available in the documentation that comes with the product The documentation can include printed documents online documents readme files and help files Most of the documentation for your server is on the documentation DVD provided with your server The Hardware Maintenance Manual is kept updating and the most up to date version is always available in English on the Lenovo Web site at http www lenovo com ThinkServerUserGuides Lenovo maintains pages on the World Wide Web where you can get the latest technical information and download documentation or device drivers and updates To access the Lenovo Support Web site to http support lenovo com For more information about your server documentation see Server documentation on page 1 If you suspect a software problem refer to the documentation including readme files and online help that comes with the operating system or software program ThinkServer Web site http www lenovo com thinkserver The ThinkServer Web site provides up to date information and services to help you buy use upgrade and maintain your server You can also do the following Shop for servers as well as upgrades and accessories for your server e Purchase additional
49. card are required Note The option package for the RAID card is designed for different types of servers and might contain additional cables that are not required to be installed into your server Two 700 mm 27 56 inches mini SAS to mini SAS signal cables One 2 pin 200 mm 7 87 inches RAID card to system board hard disk drive LED cable 38 ThinkServer Hardware Maintenance Manual Use the following instructions to connect the cables 1 Use one 700 mm 27 56 inches mini SAS to mini SAS signal cable Connect the mini SAS connector El to the port 0 on the RAID card Then connect the mini SAS connector the mini SAS signal cable connector on the 3 5 inch hot swap hard disk drive backplane installed on the lower hard disk drive cage 2 Use the other 700 mm 27 56 inches mini SAS to mini SAS signal cable Connect the mini SAS connector to the port 1 on the RAID card Then connect the mini SAS connector fj to the mini SAS signal cable connector on the 3 5 inch hot swap hard disk drive backplane installed on the upper hard disk drive cage 3 Use the 2 pin 200 mm 7 87 inches RAID card to system board hard disk drive LED cable Connect the end J to the external connector on the RAID card and the end J to the hard disk drive LED connector on the system board Figure 23 Connecting cables for server models with two backplanes and a RAID card For connector location information about the RAID card hot swap hard disk drive
50. diagnostic messages 8 Download and use the PC Doctor for DOS diagnostic program to diagnose problems See Using the diagnostic program on page 172 9 Refer to Basic troubleshooting tables on page 172 and follow the instructions for the type of problem you are experiencing If the basic troubleshooting information does not help you resolve a problem continue with the next step 10 Try using a previously server configuration to see if a recent change to hardware or software settings has caused a problem Before restoring your previous configuration capture your current configuration in case the older configuration settings do not solve the problem or have adverse effect 11 Use an antivirus program to see if your server has been infected by a virus If the program detects a virus remove the virus 12 If none of these actions solve the problem seek technical assistance See Chapter 9 Getting information help and service on page 213 Viewing the status and diagnostic LEDs Your server has status and diagnostic LEDs on the front panel the DIT panel varies by model the rear panel Ethernet status LEDs the system board the hot swap hard disk drives if supported and the optical drive s The various LEDs help you easily identify the system and device status and diagnose problems For information about the LEDs refer to the related topics in Locations on page 13 Copyright Lenovo 2011 171 Using the diagnostic pr
51. distribution board and cage assembly in place Note Use only screws provided by Lenovo a i Figure 83 Installing the power distribution board and cage assembly Refer to your note and connect the power cables of the new power distribution board and cage assembly to the system board all drives and or hot swap hard disk drive backplane s depending on the model Then properly route the cables and secure the cables with the cable clips and ties in the chassis Reinstall the front system fan s See Replacing the front system fan on page 149 Reinstall the hot swap redundant power supply module s and or the protective shield for the redundant power supply module bay 2 See Replacing a hot swap redundant power supply module on page 140 If you are instructed to return the old power distribution board and cage assembly follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To complete the replacement go to Completing the parts replacement on page 168 146 ThinkServer Hardware Maintenance Manual Replacing the front panel board assembly Attention Do not open your server or attempt any repair before reading and understanding the Safety information
52. fan on page 149 Disconnect the signal cable of the DIT module from the DIT module connector on the system board See System board components on page 42 If necessary remove any parts or disconnect any cables that might impede your access to the signal cable of the DIT module Note the cable routing and then release the signal cable of the DIT module from any cable clips or ties in the chassis Remove the screw Ell on the chassis that secures the DIT module Then carefully remove the DIT module from the chassis and pull the signal cable of the DIT module out of the hole in the chassis 3 Figure 53 Removing the DIT module Disconnect the signal cable from the rear of the DIT module Reinstall the front system fan s See Replacing the front system fan on page 149 Reinstall the front bezel See Removing and reinstalling the front bezel on page 87 If you are instructed to return the old DIT module follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To complete the removal procedure go to Completing the parts replacement on page 168 114 ThinkServer Hardware Maintenance Manual Installing or replacing an optical drive Attention Do not open your server or attempt any repair before reading and understanding the
53. for different types of servers and might contain additional cables that are not required to be installed into your server e One 700 mm 27 56 inches mini SAS to mini SAS signal cable One 2 pin 200 mm 7 87 inches RAID card to system board hard disk drive LED cable Chapter 3 Product overview 41 To connect the cables do the following 1 Use the 700 mm 27 56 inches mini SAS to mini SAS signal cable Connect the mini SAS connector to the port 0 on the RAID card Then connect the mini SAS connector to the mini SAS signal cable connector on the 3 5 inch hot swap hard disk drive backplane 2 Use the 2 pin 200 mm 7 87 inches RAID card to system board hard disk drive LED cable Connect the end J to the external connector on the RAID card and the end the hard disk drive LED connector on the system board Figure 26 Connecting cables for server models with one 3 5 inch hot swap hard disk drive backplane and a RAID card For connector location information about the RAID card hot swap hard disk drive backplane and the System board refer to the related topics in Locations on page 13 For information about connecting the appropriate power connector of the power supply to the backplane see Hot swap hard disk drive backplane on page 34 System board components Your server system board is a six layer micro ATX board based on the Intel Bromolow platform The following illustration shows the component locations on th
54. instructions or ensure that you can view the PDF version on another computer for reference Note Use any documentation that comes with the RAID card and follow those instructions in addition to the instructions in this topic To remove the RAID card do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 3 Lay the server on its side for easier operation 4 Locate the RAID card which is installed in the PCI E slot 3 on the system board See System board components on page 42 5 Remove any parts or disconnect any cables that might impede your operation 6 Disconnect all cables from the RAID card and any other related parts Note If you want to install a new RAID card after removing the old one note down the cable connections before disconnecting the cables 7 The RAID card is a kind of PCI card See Removing a PCI card on page 95 and follow those instructions to remove the RAID card Note Carefully handle the RAID card by its edges Chapter 6 Installing removing or replacing hardware 99 8 Depending on your specific server configuration you might need to connect the SATA hard disk drives to the SATA connectors on the system board if no RAID card is installed See Connecting cables
55. lists the physical specifications for your server Dimensions Width 195 mm 7 68 inches Height 430 mm 16 93 inches without foot stands 445 mm 17 52 inches with foot stands Depth 595 mm 23 43 inches including the front bezel Weight The product weight varies depending on different system configurations Range of product weight without package 19 kg 41 89 Ib to 28 kg 61 73 Ib Range of product package weight 2 8 kg 6 17 Ib to 3 5 kg 7 72 Ib Environment Air temperature Operating 10 C to 35 C 50 F to 95 F Storage 40 C to 70 C 40 F to 158 F in original shipping package Altitude 0 to 3 048 m 0 to 10 000 ft Humidity Operating 8 to 80 non condensing Storage 8 to 90 non condensing Electrical input Universal input Minimum 90 V ac Maximum 264 V ac Input frequency range 47 to 63 Hz Software This topic provides information about the software programs that you can use to help you set up use and maintain the server ThinkServer EasyStartup The ThinkServer EasyStartup program simplifies the process of configuring RAID and installing supported Microsoft Windows and Linux operating systems and device drivers on your server This program is provided with your server on a self starting bootable ThinkServer EasyStartup DVD The user guide for the program is also on the DVD and can be accessed directly from the program interface For detailed information see Us
56. models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3722 2 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 all models Chapter 8 FRU lists 191 CRU Hard disk drive cage blank metal LX KT2A MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3723 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models Hot swap 3 5 x 4 SAS SATA backplane MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X5999 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models Hot swap 2 5 x 8 SAS SATA backplane MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 all models 03X6000 MT 0391 CTO all models MT 0392 all models MT 0393 CTO all models MT 0441 CTO all models KT2A bezel assembly with label MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3712 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models 192 ThinkServer Hardware Maintenance Manual PRR umber CRU KT2A side cover assembly MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3713 1 MT 0391 CTO all m
57. not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to replace the rear system fan CAUTION Hazardous moving parts Keep fingers and other body parts away Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Depending on the model your server might look slightly different from the illustrations in this topic To replace the rear system fan do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 3 Locate the rear system fan See Server components on page 25 4 Disconnect the rear system fan cable from the system fan 3 connector on the system board See System board components on page 42 152 ThinkServer Hardware Maintenance Manual 5 rear system fan is attached to the chassis by four rubber mounts Remove the rear system fan by cutting the rubber mounts and pulling the rear system fan out of the chassis Figure 88 Removing the rear system fan 6 Touch the static protective package that contai
58. of a physical drive Rebuild Varies by configuration Rebuild physical drive s Check Consistency Varies by configuration Check consistency of virtual drive s Creating adding or deleting a RAID array This topic provides instructions on how to create add or delete a RAID array using the LSI Software RAID Configuration Utility program Note Before you create a RAID array using the LSI Software RAID Configuration Utility program make sure that the server meets the required hardware configuration For example the server needs to have the required number of SATA hard disk drives installed and connected to the system board See About RAID on page 72 for information about the required number of hard disk drives for each RAID level If you want to create a RAID 5 array using the LSI Software RAID Configuration Utility program the server also needs to have a ThinkServer SATA Software RAID 5 Key installed on the system board See Installing or removing the ThinkServer SATA Software RAID 5 Key on page 102 To create add or delete a RAID array using the LSI Software RAID Configuration Utility program do the following 1 Start the LSI Software RAID Configuration Utility program See Starting the LSI Software RAID Configuration Utility program on page 74 2 On the main interface of the program do one of the following depending on your needs f you want to create a RAID array select Easy Configuration and then follow the inst
59. off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server Chapter 6 Installing removing or replacing hardware 133 2 Remove the server cover See Removing the server cover on page 85 3 Remove the front bezel See Removing and reinstalling the front bezel on page 87 4 Locate the hot swap hard disk drive backplane s See Hot swap hard disk drive backplane on page 34 5 Remove the front system fan See Replacing the front system fan on page 149 6 Remove all the installed hot swap hard disk drives and dummy trays if any from the hard disk drive cage See Installing or replacing a hot swap hard disk drive on page 119 7 Note down the cable connections on the backplane and then disconnect all the cables from the backplane 8 Lift the release latch slide the hard disk drive cage out of the front of the chassis Note The following illustration shows the 3 5 inch hard disk drive cage For the 2 5 inch hard disk drive cage the removal procedure is the same Figure 71 Removing the hard disk drive cage 9 Depending on whether your server has a 2 5 inch hot swap hard disk drive cage with backplane or 3 5 inch hot swap hard disk drive cage s with backplane s do one of the following 194 ThinkServer Hardware Maintenance Manual e For the 3 5 inch hot swap hard disk drive ba
60. on the number of drives attached to the controller and the RAID level selected e Supports hot spare drives Creates a RAID response file that can be used to configure RAID controllers on similarly configured Lenovo servers See Using the ThinkServer EasyStartup program on page 69 and view the user guide from the main interface of the program Some RAID management software is also provided on the ThinkServer EasyStartup DVD to help you manage RAID arrays and RAID controllers in an operating system environment After you enter the operating system insert the ThinkServer EasyStartup DVD into the optical drive The installation packages for the programs are located in the Utilities and Others folder in the root directory of the DVD The ThinkServer EasyStartup DVD is designed for different types of servers and the Utilities and Others folder might contain additional installation packages that are not required to be installed into your server For more information see Installing and using the MegaRAID Storage Manager program on page 79 and Configuring the advanced SATA or SAS hardware RAID on page 79 Configuring the onboard SATA software RAID The onboard SATA software RAID controller is integrated in the Intel C202 chip on the system board If your server has SATA hard disk drives that are connected to the system board you can use the LSI Software RAID Configuration Utility program to configure RAID independently of the operating system Yo
61. operating manual Certain assemblies inside this product for example assemblies that contain a battery may have an EPUP which is lower than the EPUP on this product Turkish statement of compliance The Lenovo product meets the requirements of the Republic of Turkey Directive on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Appendix A Notices 225 T rkiye Y netmeli ine Uygunluk Beyan Bu Lenovo r n T C evre ve Orman Bakanl n n Elektrik ve Elektronik E yalarda Baz Zararl Maddelerin Kullan m n n Sinirlandirilmasina Dair Y netmelik direktiflerine uygundur EEE Y netmeli ine Uygundur German Ordinance for Work gloss statement The product is not suitable for use with visual display work place devices according to clause 2 of the German Ordinance for Work with Visual Display Units Das Produkt ist nicht f r den Einsatz an Bildschirmarbeitspl tzen im Sinne 2 der Bildschirmarbeitsverordnung geeignet Electronic emission notices The following information refers to the Lenovo ThinkServer machine types 0387 0388 0389 0390 0391 0392 0393 and 0441 Federal Communications Commission FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against h
62. option directly from Lenovo The option name is Lenovo Removable Disk Technology RDX USB Drive Bundle Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Notes 1 Depending on the model your server might look slightly different from the illustrations in this topic 2 Use any documentation that comes with the optical drive and follow those instructions in addition to the instructions in this topic To install or replace an optical drive do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 3 Locate the optical drive bays See Server components on page 25 4 Depending on whether you are installing or replacing an optical drive do one of the following e f you are installing a secondary optical drive in the upper optical drive bay remove the front bezel See Removing and reinstalling the front bezel on page 87 Then remove the plastic shield for the bay from the front panel Remove the screw Elf that secures the metal EMI shield covered on the upper optical drive bay Insert a finger into the hole in the EMI shield and carefully pull the EMI shield out of the front of the chassis
63. or region are usually available only in that country or region 196 ThinkServer Hardware Maintenance Manual Power cord United States MT 0387 CTO 11U 12U MT 0388 CTO 11U 12U 13U 14U MT 0389 CTO 11U MT 0390 CTO 11U 12U 13U 41R3184 MT 0391 CTO 11U MT 0392 CTO 11U 12U 13U 14U 15U MT 0393 CTO 11U 12U MT 0441 CTO 11U 12U 13U 14U 15U 16U Power cord China MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 41R3256 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Power cord MT 0387 MT 0388 MT 0389 MT 0390 24R2633 MT 0391 MT 0392 MT 0393 MT 0441 Power cord Brazil MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 45J9595 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Chapter 8 FRU lists 197 Power cord LA High Voltage Argentina Paraguay Uruguay MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Power cord Australia and New Zealand MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Power cord Korea MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Power cord Hong Kong Singapore Malaysia Brunei United Kingdom Ireland MT 0387 CTO 11G 12G MT 0388 CTO 12G 13G MT 0389 CTO 11G MT 0390 CTO 11G 12G 13G MT 0391 CTO MT 0392 CTO MT 0393 CTO 11G 12G MT 0441 CTO 11G 12G 13G 14G 15G 16G 198 Thin
64. previous password will be cleared Note If you delete an administrator password the user password will also be deleted For security reasons it is recommended that you always set a password for your server 5 Press F10 to save settings and exit the Setup Utility program If you have forgotten the password you can use the Clear password jumper on the system board to erase the password See System board jumpers on page 46 Then set a new password for the server Configuring the TPM function The TPM function provides a hardware security solution to encrypt data and protect the server The TPM function is only available when there is a TPM module installed in your server See Installing the TPM module on page 109 You can purchase a TPM module from Lenovo After installing a TPM module you need to check if the TPM function is enabled in the Setup Utility program To enable the TPM function in the Setup Utility program do the following 1 Start the Setup Utility program See Starting the Setup Utility program on page 55 2 On the Security menu select TPM Support Make sure that the TPM Support is set to Enabled 3 When the TPM Support is set to Enabled the TPM State item is displayed Set the TPM State to Enabled 4 Press F10 to save settings and exit the Setup Utility program The server will restart in order to enable the TPM function Selecting a startup device If your server does not start up from a desired device su
65. problems See Optical drive problems on page 173 The operating system installation program continuously Make more space available on the hard disk drive loops The ThinkServer EasyStartup program cannot start the 1 Make sure that the operating system media is operating system media supported by the ThinkServer EasyStartup program version your are using For a list of the supported operating systems refer to the user guide and compatibility notes for the ThinkServer EasyStartup program through the program main interface See Starting the ThinkServer EasyStartup program on page 70 Verify if the optical drive or the disc has problems See Optical drive problems on page 173 Optical drive problems Follow the suggested actions for the corresponding symptom in the order in which they are listed until the problem is solved If none of these actions solve the problem see Troubleshooting procedure on page 171 for the subsequent steps you should check after using the information in this topic If the problem cannot be solved by yourself seek technical assistance See Chapter 9 Getting information help and service on page 213 Notes 1 If you are instructed to remove install or replace any CRUS refer to the related procedure in Chapter 6 Installing removing or replacing hardware on page 83 2 If an action step is preceded by Trained service technician only this action step is reserved for a trained serv
66. provide advanced server management features Your server system board has a module called electrically erasable programmable read only memory EEPROM also referred to as flash memory You can easily update the POST the BIOS and BMC firmware and the Setup Utility program by starting your server with a system program update disc or a bootable USB key Lenovo might make changes and enhancements to the BIOS and BMC firmware When updates are released they are available for download on the Lenovo Support Web site at http support lenovo com Instructions for using the updates also are available in a TXT file on the same Web page with the updates You can download a self starting disc image known as an ISO image for the update program and create a system program update disc or download a BIOS update package and copy all files in the package to a bootable USB key and start the server from the USB key You can also use the Firmware Updater program to help you keep the server firmware up to date See Updating the firmware on page 80 Downloading the BIOS update utility program Before updating or recovering your BIOS you need to download a BIOS update utility program from the Lenovo Support Web site To download the BIOS update utility program do the following Note Lenovo maintains the Support Web site by making changes and improvements periodically The actual procedure might vary slightly from what is described in this topic 1 Go
67. replacement go to Completing the parts replacement on page 168 Completing the parts replacement This topic provides instructions to help you complete the parts replacement and turn on your server To complete the parts replacement you must properly route the cables inside the server reinstall the server cover reconnect all the external cables and for some devices update the firmware and run the Setup Utility program to do further setup Reinstalling the server cover and reconnecting cables Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to reinstall the server cover and reconnect cables to your server Attention For proper cooling and airflow reinstall the server cover before turning on the server Operating the server for extended periods of time more than 30 minutes with the server cover removed might damage server components Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Depending on the model your server might look slightly different from the illustrations in this topic To reinstall the server cover and reconnect cables to your server do the following 1 Make sure that all components have been reassembled correctly and that no tools or loose screws are left inside your serv
68. server Remove the server cover See Removing the server cover on page 85 Lay the server on its side for easier operation Remove the heat sink and fan assembly See Replacing the heat sink and fan assembly on page 154 A WwW N Gently press down the small handle on the microprocessor socket and then pull the handle a little bit outward to release it from the secured position Then pivot the handle upward until the handle and the microprocessor retainer are in the fully open position Note Your microprocessor and socket might look different from the one illustrated Figure 92 Lifting the handle to open the microprocessor retainer 158 ThinkServer Hardware Maintenance Manual 6 Touch only the edges of the microprocessor and carefully lift it straight up and out of the microprocessor Socket Place the old microprocessor on a static protective surface Note Do not touch the gold contacts on the bottom of the microprocessor Figure 93 Removing the microprocessor 7 Make sure that the small handle and the microprocessor retainer are in the fully open position Note Do not drop anything onto the microprocessor socket while it is exposed The socket pins must be kept as clean as possible 8 Touch the static protective package that contains the new microprocessor to any unpainted surface on the outside of the server Then remove the new microprocessor from the package 9 Remove the ne
69. server On The BMC has no power or fails Blinking The BMC is working E Et POST code diagnostic LEDs During the system boot process the BIOS executes several platform configuration processes each of which is assigned a specific hex POST code number When each configuration routine is started the BIOS displays the POST code number through the POST code diagnostic LEDs on the system board To assist in troubleshooting a system hang during the POST process the diagnostic LEDs can be used to identify the last POST process executed The POST code diagnostic LED 0 callout Eg is the LSB and the POST code diagnostic LED 7 callout EB is the MSB If a POST code diagnostic LED is lit it indicates 1 in the binary numeral system otherwise it indicates 0 For example if POST code diagnostic LEDs E3 and are lit you can read the number as the following Binary symbol Tt fT 3 0 31 0 1 0 10101010 indicates a corresponding POST code Note The POST code diagnostic LEDs and POST error code information are intended for trained service personnel of Lenovo The following table lists information about the POST error codes POST code diagnostic LEDs POST error code 00001111 Microcode not loaded 01010000 0x50 Memory initialization error The memory type is invalid or the memory speed is incompatible 01010001 0x51 Memory initialization error The Serial Pr
70. to prevent unauthorized access to your server You do not have to set a password to use your server However using a password improves computing security If you decide to set a password read the following topics Setup Utility program password type The following types of passwords are available in the Setup Utility program Administrator password Setting an administrator password deters unauthorized users from changing configuration settings If you are responsible for maintaining the configuration settings of several computers you might want to set an administrator password When an administrator password is set you are prompted to type a valid password each time you try to access the Setup Utility program The Setup Utility program cannot be accessed until a valid password is typed in User password only available when you have set an administrator password When user password is set the server cannot be used until a valid password is typed in Note If both the administrator password and user password are set you can type either password However you must use your administrator password to change any configuration settings Password considerations For security reasons it is recommended to use a strong password that cannot be easily compromised Notes 1 The Setup Utility program passwords are not case sensitive 2 The server supports Setup Utility program passwords that consist of up to 20 characters To set a stron
71. to the microprocessor fan connector on the system board See System board components on page 42 Note If the heat sink and fan assembly cable is too long loosely knot the cable for proper cable routing 12 If you are instructed to return the old heat sink and fan assembly follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To complete the replacement go to Completing the parts replacement on page 168 Replacing the microprocessor Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to replace the microprocessor Chapter 6 Installing removing or replacing hardware 157 CAUTION A A The heat sink and fan assembly and the microprocessor might be very hot Turn off the server and wait three to five minutes to let the server cool before removing the server cover Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference To replace the microprocessor do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
72. use the iKVM key to gain location independent remote access to respond to critical incidents and to undertake necessary maintenance Therefore working as an integrated solution in your server the iKVM key provides Chapter 6 Installing removing or replacing hardware 105 increased level of manageability over the basic server management available to the system board You can purchase an iKVM key directly from Lenovo Installing the iKVM key Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to install the iKVM key Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Use any documentation that comes with the iKVM key and follow those instructions in addition to the instructions in this topic To install the iKVM key do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 3 Lay the server on its side for easier operation 4 Touch the static protective package that contains the iKVM key to any unpainted surface on the outside of the server Then take the iKV
73. 03X3842 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models 2 5 inch hard disk drive tray V2 0 MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3836 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models 3 5 inch hard disk drive dummy tray V2 0 MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3837 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models 190 ThinkServer Hardware Maintenance Manual 2 5 inch hard disk drive dummy tray V2 0 MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3838 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models 3 5 inch hard disk drive cage MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3703 2 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 all models 2 5 inch hard disk drive cage MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3704 2 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models Non hot swap hard disk drive cage shield MT 0387 CTO all
74. 100 percent means that the system gives priority to rebuilding the failing drives The rebuild rate can be configured between 0 percent and 100 percent At 0 percent the rebuild is done only if the system is not doing anything else At 100 percent the rebuild has a higher priority than any other system activity To configure the rebuild rate using the LSI Software RAID Configuration Utility program do the following Note Using a rebuild rate of 0 or 100 percent is not recommended The default value is 30 percent 1 Start the LSI Software RAID Configuration Utility program See Starting the LSI Software RAID Configuration Utility program on page 74 2 On the main interface of the program select Objects gt Adapter gt Rebuild Rate Note Use up and down arrow keys to navigate between items and press Enter to select an option 3 Set the rebuild rate by typing a desired value from the keyboard directly Running a consistency check This topic provides instructions on how to run a consistency check for virtual drives using the LSI Software RAID Configuration Utility program A consistency check is an operation that verifies that all stripes on a virtual drive with a redundant RAID level are consistent The consistency check operation verifies correctness of the data on virtual drives that use RAID 1 5 and 10 RAID 0 does not provide data redundancy For example in a system with parity checking consistency means computing the data
75. 388 CTO 12G 13G MT 0389 CTO 11G MT 0390 CTO 11G 12G 13G 41R3220 MT 0391 CTO MT 0392 CTO MT 0393 CTO 11G 12G MT 0441 CTO 11G 12G 13G 14G 15G 16G Power cord i MT 0387 MT 0388 MT 0389 MT 0390 41R3341 MT 0391 MT 0392 MT 0393 MT 0441 200 ThinkServer Hardware Maintenance Manual Power cord United States MT 0387 CTO 11U 12U MT 0388 CTO 11U 12U 13U 14U MT 0389 CTO 11U MT 0390 CTO 11U 12U 13U 41R3184 MT 0391 CTO 11U MT 0392 CTO 11U 12U 13U 14U 15U MT 0393 CTO 11U 12U MT 0441 CTO 11U 12U 13U 14U 15U 16U Power cord China MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 41R3256 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Power cord MT 0387 MT 0388 MT 0389 MT 0390 24R2633 MT 0391 MT 0392 MT 0393 MT 0441 Power cord Brazil MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 45J9595 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Chapter 8 FRU lists 201 Power cord LA High Voltage Argentina Paraguay Uruguay MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Power cord Australia and New Zealand MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Power cord Korea MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Power cord Hong Kong Singapore Malaysia Brunei United Kingdo
76. 87 What to do next To work with another piece of hardware go to the appropriate section To complete the installation go to Completing the parts replacement on page 168 Removing the DIT module Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to remove the DIT module This topic applies only to server models that come with the DIT module Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Notes 1 Depending on the model your server might look slightly different from the illustration in this topic 2 f you remove the DIT module the server will lose the diagnostic LEDs on the DIT panel To remove the DIT module do the following Chapter 6 Installing removing or replacing hardware 113 oa 2 W m 10 11 12 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server Remove the server cover See Removing the server cover on page 85 Remove the front bezel See Removing and reinstalling the front bezel on page 87 Locate the DIT module See DIT module on page 18 Remove the front system fan s See Replacing the front system
77. A WEEE jelz s elektromos s elektronikai felszerel sek EEE felhaszn l inak a WEEE direkt va IV f ggel k nek megfelel en nem szabad vegyes h zi szem tk nt kidobniuk az eszk z ket EEE hanem a v s rl k sz m ra rendelkez sre ll megl v begy jt si keretrendszert felhaszn lva kell gondoskodniuk az elektromos hullad k WEEE visszajuttat s r l s jrahasznos t s r l valamint minimaliz lniuk kell az eszk z k EEE lehets ges hat sait a k rnyezetre s az emberi eg szs gre a vesz lyek megel z se rdek ben Tov bbi WEEE inform ci k http www lenovo com lenovo environment Restriction of Hazardous Substances Directive RoHS This topic provides statements about the Restriction of Hazardous Substances Directive RoHS 224 ThinkServer Hardware Maintenance Manual China RoHS CEIE TE P232 8 53 Toxic Hazardous Substances and Elements Table ASA SY RMR BAM x pes Pb 547 DIE chassis VE BR external covers HE mechanical assemblies BURR air moving devices ADU E cooling assembly VI FEBR memory modules SS BR processor modules oR CH amp Be monitor BUR mouse mA E cable assemblies A power supply AF fii Be
78. AID 5 distributes parity along with the data and requires all drives but one to be present to operate drive failure requires replacement but the array is not destroyed by a single drive failure Upon drive failure any subsequent read operations can be calculated from the distributed parity so that the drive failure is masked from the end user The array will have data loss in the event of a second drive failure and is vulnerable until the data that was on the failing drive is rebuilt onto a replacement drive A single drive failure in the set will result in reduced performance of the entire set until the failing drive has been replaced and rebuilt RAID 5 requires a minimum number of three hard disk drives RAID 10 combination of RAID 0 and RAID 1 RAID 10 consists of striped data across mirrored spans A RAID 10 drive group is a spanned drive group that creates a striped set from a series of mirrored drives RAID 10 allows a maximum of eight spans You must use an even number of drives in each RAID virtual drive in the span The RAID 1 virtual drives must have the same stripe size RAID 10 provides high data throughput and complete data redundancy but uses a larger number of spans RAID 10 requires a minimum number of four hard disk drives and also requires an even number of drives for example six hard disk drives or eight hard disk drives 72 ThinkServer Hardware Maintenance Manual RAID 50 a combination of RAID 0 RAID 5
79. Advanced menu in the Setup Utility program You can view or change various server component settings on the Advanced menu The following table shows the contents of the Advanced menu On each submenu press the Enter key to show selectable options and select a desired option by using up and down arrow keys or type desired values from the keyboard directly Some items are displayed on the menu only if the server supports the corresponding features Notes Enabled means that the function is configured Disabled means that the function is not configured Default values are in boldface in the Selections column Advanced menu items 7 EBENE Processor Configuration set the microprocessor configuration parameters Disabled Enabled Intel Hyper Threading Technology Active Processor Cores Disabled Enabled Intel Virtualization Technology Chapter Enable or disable the Intel Hyper Threading Technology Set the active microprocessor cores Enable or disable the Intel Virtualization Technology 57 5 Configuring the server Intel EIST Technology Disabled Enable or disable the Intel Enabled EIST Technology P State Coordination HW ALL Change the P State e SW ALL Coordination type e SW ANY Intel Turbo Boost Disabled Enable or disable the Intel Technology Enabled Turbo Boost Technology C1E Support Disabled Enable or disable the C1E Enabled Support C
80. Air Conditioning Engineers Inc The deliquescent relative humidity of particulate contamination is the relative humidity at which the dust absorbs enough water to become wet and promote ionic conduction 3 ANSI ISA 71 04 1985 Environmental conditions for process measurement and control systems Airborne contaminants Instrument Society of America Research Triangle Park North Carolina U S A Important information for the European Directive 2002 96 EC EU Only The Waste Electrical and Electronic Equipment WEEE mark applies only to countries within the European Union EU and Norway Appliances are labeled in accordance with European Directive 2002 96 EC concerning waste electrical and electronic equipment WEEE The Directive determines the framework for the return and recycling of used appliances as applicable throughout the European Union This label is applied to various products to indicate that the product is not to be thrown away but rather reclaimed upon end of life per this Directive Users of electrical and electronic equipment EEE with the WEEE marking per Annex IV of the WEEE Directive must not dispose of end of life EEE as unsorted municipal waste but use the collection framework available to them for the return recycle recovery of WEEE and minimize any potential effects of EEE on the environment and human health due to the presence of hazardous substances For additional WEEE information go to http www lenovo com
81. CTO 03X3784 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Chapter 8 FRU lists 207 Shipgroup FRU number Microsoft Windows Small Business Server 2011 Essentials English MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3785 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microsoft Windows Small Business Server 2011 Essentials French MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3786 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microsoft Windows Small Business Server 2011 Essentials German MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3787 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microsoft Windows Small Business Server 2011 Essentials Japanese MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3788 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO 208 ThinkServer Hardware Maintenance Manual Shipgroup FRU number CRU Microsoft Windows Server 2008 R2 Standard Edition 64 bit French MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 90Y1184 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microsoft Windows Server 2008 R2 Standard Edition 64 bit German MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 90Y1185 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Microsoft Windows Server 2008 R2 Standard Edition 64 bit Spanish MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 90Y1187 1 MT 0391
82. EN SATA Configuration SATA Mode DE Mode set SATA configuration AHCI Mode parameters RAID Mode SATA 0 SATA Port1 PCI Configuration set PCI Onboard Graphics Disabled configuration parameters Controller Enabled Primary Graphics Onboard Add On Onboard LAN1 I O ROM Disabled Enabled If the power is interrupted when the server is on after the power resumes e Ifyou have selected Stay off the server will stay in the off state If you have selected Last State the server will resume to the last state If you have selected Power on the server will restart automatically Select SATA controller operation mode If you want to configure RAID choose RAID Mode for the SATA controller View the information about the SATA device connected to the SATA connector 0 on the system board View the information about the SATA device connected to the SATA connector 1 on the system board View the information about the SATA device connected to the SATA connector 2 on the system board View the information about the SATA device connected to the SATA connector 3 on the system board View the information about the SATA device connected to the SATA connector 4 on the system board View the information about the SATA device connected to the SATA connector 5 on the system board Enable or disable the onboard graphics controller Choose a mode for primary graphics The Add O
83. IED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions therefore this statement may not apply to you This information could include technical inaccuracies or typographical errors Changes are periodically made to the information herein these changes will be incorporated in new editions of the publication Lenovo may make improvements and or changes in the product s and or the program s described in this publication at any time without notice The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons The information contained in this document does not affect or change Lenovo product specifications or warranties Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties All information contained in this document was obtained in specific environments and is presented as an illustration The result obtained in other operating environments may vary Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you Any references in this publication to non Lenovo Web sites are provided for convenience only and do not in any manner serve as
84. Installing the RAID 5 key on the RAID card What to do next To work with another piece of hardware go to the appropriate section To complete the installation go to Completing the parts replacement on page 168 Then the hardware RAID 5 and 50 levels are available for your server if your server has the required number of hard disk drives installed Refer to the MegaRAID SAS Software User Guide on the documentation DVD that comes with your server for information about how to configure the hardware RAID Removing the RAID 5 key from the RAID card Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to remove the RAID 5 key from the RAID card Notes 1 This topic applies only to server models that have a RAID card with the RAID 5 key option installed 2 f you remove the RAID 5 key from the RAID card the hardware RAID 5 and 50 levels are not available Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Use any documentation that comes with the RAID 5 key and follow those instructions in addition to the instructions in this topic To remove the RAID 5 key from the RAID card do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect al
85. Lenovo Support Web site e Important Notices This document includes safety and legal notices that you should read and understand before using the server Documentation DVD The documentation DVD which comes with your server contains various documents for your server in Portable Document Format PDF To view the documentation you need to have the Adobe Reader program installed You can download the desired language version of the latest Adobe Reader program from the Adobe Web site at http www adobe com Note Lenovo maintains pages on the World Wide Web where you can get the latest technical information and download documentation or device drivers and updates Some information in the documents on the documentation DVD might change without notice after the first release of the DVD You can always obtain all the most up to date documentation for your server from the Lenovo Web site at http www lenovo com ThinkServerUserGuides The following documents are on the documentation DVD that comes with your server e Safety Information This is a multilingual document that includes all the safety statements for your product in more than 30 languages Be sure to read and understand all the safety statements before using the product e Warranty and Support Information This document includes the Lenovo warranty statement CRUs information and information about how to contact Lenovo Support e User Guide This document provides detailed
86. M key out of the package 106 ThinkServer Hardware Maintenance Manual 5 Locate the iKVM key connector on the system board and then insert the iKVM key into the iKVM key connector Note Make sure that the iKVM key is securely seated on the system board Figure 47 Installing the iKVM key What to do next To work with another piece of hardware go to the appropriate section To complete the installation go to Completing the parts replacement on page 168 Then you can refer to the Remote Management Module User Guide on the documentation DVD that comes with your server for more information about the iKVM function and server remote management Removing the iKVM key Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to remove the iKVM key if the server has one installed Before you begin print all the related instructions or ensure that y
87. MI helps lower the overall costs of server management You can find more information about IPMI 2 0 from the Web site of Intel The BMC also supports some non IPMI features such as the Dynamic Host Configuration Protocol DHCP and the Platform Environment Control Interface PECI to provide more system management functions Refer to the Remote Management Module User Guide on the documentation DVD that comes with your server for more information Hot swap feature Some models support hot swap hard disk drives and or hot swap redundant power supply modules With the hot swap feature you can install remove or replace hard disk drives or a failing power supply module without turning off the server 10 ThinkServer Hardware Maintenance Manual Preboot Execution Environment The Intel PXE technology enables you to boot your computers load an operating system or deploy executable images from a remote server by using a network interface The operation can be done independently of local data storage devices such as hard disk drives or installed operating systems Redundant Array of Independent Disks RAID Your server supports onboard SATA software RAID and advanced SATA SAS hardware RAID configurations if you have a required RAID card installed For detailed information see Configuring RAID on page 71 Status light emitting diodes LEDs and diagnostic LEDs For more information about the LEDs for your server refer to the rela
88. MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 0509815 0391 0392 0393 0441 Hard disk drive hot swap 300 5 5 enterprise 6 Gb s cache 2 5 inch drive assembly MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO posue MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO 184 ThinkServer Hardware Maintenance Manual Hard disk drive hot swap 450 GB 5 5 enterprise 6 Gb s cache 2 5 drive assembly MT 0387 MT 0388 MT 0389 MT 0390 MT 0391 MT 0392 MT 0393 MT 0441 MT 0387 MT 0388 MT 0389 MT 0390 MT 0391 MT 0392 MT 0393 MT 0441 MT 0387 MT 0388 MT 0389 MT 0390 MT 0391 MT 0392 MT 0393 MT 0441 MT 0387 MT 0388 MT 0389 MT 0390 MT 0391 MT 0392 MT 0393 MT 0441 Hard disk drive hot swap 600 GB SAS enterprise 6 Gb s xx MB cache 2 5 inch drive assembly CTO CTO CTO 03X3921 1 CTO CTO CTO CTO CTO CTO CTO CTO CTO CTO CTO CTO 03X3920 Front system fan second cage 9225 fan CTO all models CTO all models CTO all models CTO all models 03X3707 CTO all models CTO all models CTO all models CTO all models System board CMOS battery CTO 11U 11G 12U 12G 110 120 12G 130 13G 140 CTO 110 11F CTO 110 11G 120 12G 130 13G 03 3721 CTO 11U CTO 11U 12U 13U 14U 15U CTO 11U 11G 12U 12G CTO 11U 11G 12U 12G 13U 13G 14U 14G 15U
89. O 11U 11G 12U 12G 13U 13G 14U 14G 15U 15G 16U 16G 2 pin 200 mm 7 87 inches RAID card to system board hard disk drive LED cable MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3757 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Power cords For your safety Lenovo provides a power cord with a grounded attachment plug to use with this Lenovo product To avoid electrical shock always use the power cord and plug with a properly grounded outlet Lenovo power cords used in the United States and Canada are listed by Underwriter s Laboratories UL and certified by the Canadian Standards Association CSA For units intended to be operated at 115 volts Use a UL listed and CSA certified cord set consisting of a minimum 18 AWG Type SVT or SJT three conductor cord a maximum of 15 feet in length and a parallel blade grounding type attachment plug rated 15 amperes 125 volts For units intended to be operated at 230 volts U S use Use a UL listed and CSA certified cord set consisting of a minimum 18 AWG Type SVT or SJT three conductor cord a maximum of 15 feet in length and a tandem blade grounding type attachment plug rated 15 amperes 250 volts For units intended to be operated at 230 volts outside the U S Use a cord set with a grounding type attachment plug The cord set should have the appropriate safety approvals for the country in which the equipment will be installed Lenovo power cords for a specific country
90. PU C3 Report Disabled Enable or disable the CPU ACPI C2 C3 report e ACPI CPU C6 Report Disabled Enable or disable the CPU Enabled C6 report Package C State Limit CO Set the Package C state e limit e C7 No Limit Hardware Prefetcher e Disabled Enable or disable the Enabled hardware prefetcher function Adjacent Cache Line e Disabled Enable or disable the Prefetch e Enabled adjacent cache line prefetcher function Memory Configuration Memory Reset e No Set the memory module set memory configuration e Yes reset options If a memory parameters and view module encounters any information about the errors set this option to installed memory modules Yes to try to re initialize the memory module Chipset Configuration Intel VT d Technology Disabled Enable or disable the Intel set chipset configuration e Enabled VT d technology parameters Intel TXT Technology Disabled Enable or disable the Intel Trusted Execution Enabled Technology TXT Serial Port 1 Disabled Enable or disable the serial Enabled port 1 COM 1 Serial Port 2 Disabled Enable or disable the serial e Enabled port 2 COM 2 Power on by RTC Alarm Disabled Enable or disable powering e Enabled on by RTC alarm Restore on AC Power Loss Stay off Select the system resume Last State status after ac power loss 58 ThinkServer Hardware Maintenance Manual Selections
91. RAID 50 uses distributed parity and disk striping A RAID 50 drive group is a spanned drive group in which data is striped across multiple RAID 5 drive groups RAID 50 works best with data that requires high reliability high request rates high data transfers and medium to large capacity Note Having virtual drives of different RAID levels such as RAID 0 and RAID 5 in the same drive group is not allowed For example if an existing RAID 5 virtual drive is created out of partial space in an array the next virtual drive in the array has to be RAID 5 only RAID 50 requires a minimum number of six hard disk drives For detailed information about RAID refer to Introduction to RAID in the MegaRAID SAS Software User Guide on the documentation DVD that comes with your server RAID for your server This topic provides information about the RAID supported by your server Your server supports the following two types of RAID configurations Onboard SATA software RAID configuration using the LSI Software RAID Configuration Utility program and RAID management using the MegaRAID Storage Manager program The onboard SATA software RAID controller is integrated in the Intel C202 chip on the system board If your server has SATA hard disk drives that are connected to the system board you can use the LSI Software RAID Configuration Utility program to configure RAID Your server supports onboard SATA software RAID levels 0 1 and 10 You can also activ
92. SB drive bundle cartridge MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 67Y1421 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Lenovo 320 GB RDX USB drive bundle cartridge MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 67Y1422 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Lenovo 500 GB RDX USB drive bundle cartridge MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 67Y1423 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Chapter 8 FRU lists 181 Hard disk drive hot swap 250 GB SATA enterprise 7200 rpm 3 Gb s 3 5 inch drive assembly MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Hard disk drive hot swap 500 GB SATA enterprise 7200 rpm 3 Gb s 3 5 inch drive assembly MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 9348519 0391 0392 0393 0441 03 3674 Hard disk drive hot swap 1 SATA enterprise 7200 rpm 3 Gb s 3 5 inch drive assembly MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO pence MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Hard disk drive hot swap 2 TB SATA enterprise 7200 rpm 3 Gb s 3 5 inch drive assembly MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 0391 0392 0393 0441 182 ThinkServer Hardware Maintenance Manual Hard disk
93. ST and BIOS is being updated your server might not restart correctly Make sure that you perform the BIOS update procedure in an environment with a steady power supply Besides make sure that your server can restart successfully without encountering hardware problems If you have updated the BIOS firmware all the BIOS settings become the default settings of the updated BIOS version You need to check and reconfigure the BIOS settings for your specific needs You can note down your specific BIOS settings before updating the BIOS for an easier reconfiguration in the new BIOS version To update flash the BIOS do the following 1 Download a BIOS update utility program and its installation instructions from the Lenovo Support Web site Then make a bootable disc or a bootable USB key and print the TXT file that contains the installation instructions See Downloading the BIOS update utility program on page 67 Turn on the server and press the F1 key as soon as you see the logo screen to start the Setup Utility program See Starting the Setup Utility program on page 55 On the Security menu check the BIOS Write Protect setting To update flash the BIOS the BIOS Write Protect item must be set to Disabled Press F10 to save settings and exit the Setup Utility program Then follow the installation instructions to update flash the BIOS using a disc or USB key The system will restart automatically after the update
94. See Server Management menu on page 61 Boot Options See Boot Options menu on page 62 Boot Manager See Boot Manager menu on page 64 Exit Exit menu on page 64 Main menu After entering the Setup Utility program you can see the Main menu which lists some basic information about the system BIOS version and build date the microprocessor memory and the system date and time 56 ThinkServer Hardware Maintenance Manual The following illustration shows an example of the Main menu in the Setup Utility program BIOS Setup Utility Main Advanced Security Server Management Boot Options Boot Manager Exit System BIOS Set the date Use Tab to Version 0 9b Switch between data Build Date 04 15 2011 elements Processor Genuine Intel R CPU 0 9 3 10GHz Core Frequency 3 10 GHz 1 Count Memory Size 8192 MB DDR3 1333 System Date Wed 04 20 2011 System Time 19 53 47 gt lt Select Screen TL Select Item Enter Select Change Opt F1 General Help F3 Previous Values F9 Optimized Defaults F10 Save ESC Exit Version 2 10 1208 Copyright C 2002 2011 American Megatrends Inc Figure 31 An example of the Main menu in the Setup Utility program To set the system date and time on the Main menu see Setting the system date and time on page 64 Advanced menu This topic provides information about the various configuration menus and items on the
95. Service which automatically entitles you to obtain warranty service throughout the warranty period Service will be performed by service providers authorized to perform warranty service Service methods and procedures vary by country and some services might not be available in all countries International Warranty Service is delivered through the method of service such as depot carry in or on site service that is provided in the servicing country Service centers in certain countries might not be able to service all models of a particular machine type In some countries fees and restrictions might apply at the time of service To determine whether your computer is eligible for International Warranty Service and to view a list of the countries where service is available go to http support lenovo com click Product amp Service Warranty and follow the instructions on the Web page For technical assistance with the installation of or questions related to Service Packs for your installed Windows product refer to the Microsoft Product Support Services Web site at http support microsoft com directory or you can contact the Customer Support Center Some fees might apply Purchasing additional services During and after the warranty period you can purchase additional services such as support for hardware operating systems and application programs network setup and configuration services upgraded or extended hardware repair services a
96. TA software RAID 5 is available for your server if your server has the required number of hard disk drives installed To configure RAID see Configuring RAID on page 71 Removing the system board RAID 5 key Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to remove the system board RAID 5 key Notes 1 This topic applies only to servers that have a system board RAID 5 key option installed 2 If you remove the system board RAID 5 key the onboard SATA software RAID 5 will be disabled Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Use any documentation that comes with the system board RAID 5 key and follow those instructions in addition to the instructions in this topic To remove the system board RAID 5 key do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 3 Lay the server on its side for easier operation 104 ThinkServer Hardware Maintenance Manual 4 Locate the iButton socket on the system board Open the retaining clip Ell on the iButton socke
97. TION Hazardous moving parts Keep fingers and other body parts away CAUTION AA The heat sink and fan assembly might be very hot Turn off the server and wait three to five minutes to let the server cool before removing the server cover Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference To replace the heat sink and fan assembly do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server Remove the server cover See Removing the server cover on page 85 Locate the heat sink and fan assembly See Server components on page 25 Lay the server on its side for easier operation If necessary remove any installed PCI card that might impede your access to the heat sink and fan assembly See Removing a PCI card on page 95 Disconnect the heat sink and fan assembly cable from the microprocessor fan connector on the system board See System board components on page 42 Chapter 6 Installing removing or replacing hardware 155 6 Remove the four screws that secure the heat sink and fan assembly to the system board It is recommended that you carefully remove the four screws from the system board using the following method to avoid any possible damage to the system board
98. accordance with the Law for Promotion of Effective Utilization of Resources Lenovo Japan provides through its PC Collecting and Recycling Services for the collecting reuse and recycling of disused computers and monitors For details visit the Lenovo Web site at http www lenovo com recycling japan Pursuant to the Law for Promotion of Effective Utilization of Resources the collecting and recycling of home used computers and monitors by the manufacturer was begun on October 1 2003 This service is provided free of charge for home used computers sold after October 1 2003 For details visit the Lenovo Web site at http www lenovo com recycling japan Disposing of Lenovo computer components Some Lenovo computer products sold in Japan may have components that contain heavy metals or other environmental sensitive substances To properly dispose of disused components such as a printed circuit board or drive use the methods described above for collecting and recycling a disused computer or monitor Battery return program This product may contain a lithium or lithium ion battery Consult your user manual or service manual for specific battery information The battery must be recycled or disposed of properly Recycling facilities may not be available in your area For information on disposal or batteries outside the United States go to http www lenovo com recycling or contact your local waste disposal facility Battery recycling informati
99. an endorsement of those Web sites The materials at those Web sites are not part of the materials for this Lenovo product and use of those Web sites is at your own risk Any performance data contained herein was determined in a controlled environment Therefore the result obtained in other operating environments may vary significantly Some measurements may have been made on development level systems and there is no guarantee that these measurements will be the same on generally available systems Furthermore some measurements may have been estimated through extrapolation Actual results may vary Users of this document should verify the applicable data for their specific environment O Copyright Lenovo 2011 217 Trademarks Lenovo the Lenovo logo ThinkServer and ThinkVantage are trademarks of Lenovo in the United States other countries or both Intel Intel Core and Intel Xeon are trademarks of Intel Corporation in the United States other countries or both Microsoft Windows and Windows Server are trademarks of the Microsoft group of companies Linux is a registered trademark of Linus Torvalds in the United States other countries or both Other company product or service names may be trademarks or service marks of others Important notes Processor speed indicates the internal clock speed of the microprocessor other factors also affect application performance CD or DVD drive speed is the variable read rate Actual sp
100. anding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to remove the server cover Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Depending on the model your server might look slightly different from the illustrations in this topic To remove the server cover do the following 1 Remove all media from the drives Then turn off all attached devices and the server 2 Disconnect all power cords from electrical outlets 3 Disconnect the power cord s Input Output I O cables and all other cables that are connected to the server 4 Remove any locking device that secures the server cover such as a padlock or an integrated cable lock See Server locks on page 22 Chapter 6 Installing removing or replacing hardware 85 5 Loosen the thumbscrew that secures the server cover then slide the server cover to the rear until it is stopped Notes a The server cover is securely installed and you need to use a tool such as a screwdriver to loosen the thumbscrew that secures the server cover The thumbscrew is an integrated part of the server cover and do not try to remove the thumbscrew from the server cover b It is recommended that you wait three to five minutes to let the server cool before removing the Server cover Figure 32 Slidi
101. andwidth necessary to enable the system to obtain peak performance The chip supports and provides many features including the onboard SATA software RAID 4 pin system fan 1 connector Used to connect the cable of the lower front system fan front system fan 1 EH SATA connectors Used to connect SATA signal cables for the SATA hard disk drives or SATA optical drives 44 ThinkServer Hardware Maintenance Manual iKVM key connector Used to connect an iKVM key option which is a kind of remote management module to enable the iKVM function on your server See Installing or removing the ThinkServer iKVM Remote Management Module on page 105 Ej Internal USB 2 0 Type A connector Used to connect a device that uses a USB 2 0 Type A connector Internal dual port USB 2 0 connector 2 Used to connect the USB cable of the RDX USB drive bundle server option Internal dual port USB 2 0 connector 1 Used to connect the front panel USB cable EH System board battery Your server has a special type of memory that maintains the date time and configuration information for built in features The system board battery keeps the information active when you turn off the server Front panel connector Used to connect the front panel cable System board jumper blocks Used to configure the system board and your server See System board jumpers on page 46 Ef SATA SGPIO connector Used to connect the SGPIO port of the
102. anual There is 3 5 inch hot swap hard disk drive or a dummy hard disk drive tray installed in each hard disk drive bay to Note The number of the installed hard disk drives varies by model For the vacant drive bay there is a dummy hard disk drive tray to cover the place For information about the supported expansion card see System board components on page 42 Depending on the model your server might come with a screw secured non hot swap power supply or hot swap redundant power supply module s For more information about the memory modules see Memory module installation rules on page 90 Chapter 3 Product overview 27 The following illustration shows the components of the server with up to eight 2 5 inch hot swap SAS hard disk drives B 2 HOF 5 Ss e 2 4 DR 7 Lg V VY Figure 12 Components of the server with to eight 2 5 inch hot swap SAS hard disk drives DIT module available in some models Hard disk drive bay 1 E Front panel Hard disk drive bay 0 Optical drive bay 2 with an optical drive installed Front system fan 1 in some models Ef Optical drive bay 1 with an optical drive installed System board battery Hard disk drive bay 7 Expansion card Hard disk drive bay 2 EBJ Four memory slots installed memory modules vary by model For more information about
103. ard and carefully place it into the chassis so that the rear connectors are inserted into the corresponding holes in the rear panel and the eight screw holes in the new system board are aligned with those in the chassis Then install the eight screws following the numerical sequence as shown to secure the new system board in the chassis _ a a m e Figure 104 Installing the screws to secure the system board 18 Install all parts and connect all cables that you removed from the old system board to the new system board Refer to the information that you have noted down and the related topics in Installing removing or replacing hardware on page 89 19 If you are instructed to return the old system board follow all packaging instructions and use any packaging materials that are supplied to you for shipping Chapter 6 Installing removing or replacing hardware 167 What to do next To work with another piece of hardware go to the appropriate section To complete the
104. armful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits Lenovo is not responsible for any radio or television interference caused by using other than specified or recommended cables and connectors or by unauthorized changes or modifications to this equipment Unauthorized changes or modifications could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Industry Canada Class A emission compliance statement This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada United Kingdom telecommunications safety requirement Notice to Customers This apparatus is approved under approval number NS G 1234
105. at are connected to the server Remove the server cover See Removing the server cover on page 85 em Lay the server on its side for easier operation 4 Touch the static protective package that contains the system board RAID 5 key to any unpainted surface on the outside of the server Then take the system board RAID 5 key out of the package 5 Locate the iButton socket on the system board Insert one side of the system board RAID 5 key under one of the retaining clips on the iButton socket Then carefully press the other side of the system board RAID 5 key straight down until the key snaps into position and is secured by the two retaining clips on the iButton socket Note necessary remove any parts or disconnect any cables that might impede your operation 1000 en D m 11 Figure 45 Installing the system board RAID 5 key What to do next To work with another piece of hardware go to the appropriate section Chapter 6 Installing removing or replacing hardware 103 To complete the installation go to Completing the parts replacement on page 168 Then the onboard SA
106. ate RAID level 5 by installing a ThinkServer SATA Software RAID 5 activation key See Installing or removing the ThinkServer SATA Software RAID 5 Key on page 102 You can install and use the MegaRAID Storage Manager program to manage the RAID array and RAID controller in an operating system environment For detailed information see Configuring the onboard SATA software RAID on page 74 Advanced SATA SAS hardware RAID configuration using the WebBIOS Configuration Utility program and RAID management using the MegaRAID Storage Manager program and the MegaCLI Configuration Utility program requires a RAID card Some server models come with a required RAID card to provide advanced SATA SAS hardware RAID functions to the server You can also purchase the RAID card from Lenovo and install it into server models that support the RAID card to get advanced SATA SAS hardware RAID functions See RAID card on page 33 and Installing or removing the RAID card on page 98 for more information Note For server models with more than four hard disk drives or models that use SAS hard disk drives there must be a RAID card installed The RAID card provides the WebBIOS Configuration Utility program to help you configure RAID independently of the operating system You can also install the MegaRAID Storage Manager program and the MegaCLI Configuration Utility program to help you manage the RAID array and RAID controller in an operating system environment
107. ate section To complete the replacement go to Completing the parts replacement on page 168 160 ThinkServer Hardware Maintenance Manual Replacing the system board battery Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to replace the system board battery Your server has a special type of memory that maintains the date time and configuration information for built in features The system board battery keeps the information active when you turn off the server The system board battery normally requires no charging or maintenance throughout its life however no battery lasts forever If the system board battery fails the date time and configuration information including passwords are lost and an error message is displayed when you turn on the server Danger of explosion if battery is incorrectly replaced When replacing the lithium coin cell battery use only the same or an equivalent type that is recommended by the manufacturer The battery contains lithium and can explode if not properly used handled or disposed of Do not Throw or immerse into water Heat to more than 100 C 212 F Repair or disassemble Dispose of the battery as required by local ordinances or regulations The following statement applies to users in the state of California U S A Cal
108. ave to restart the server for the newly installed drive to be recognized See Hot swap hard disk drive status LEDs on page 32 If the hard disk drive is faulty you need to reinstall or replace it until it is operating correctly 8 Close and lock the front door 9 Do one of the following e f you are installing a hot swap hard disk drive save the removed hard disk drive dummy tray in the event that you later remove the hot swap hard disk drive and need a dummy tray to cover the drive bay f you are replacing a hot swap hard disk drive and are instructed to return the old hot swap hard disk drive follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To configure RAID go to Configuring RAID on page 71 Removing or installing a non hot swap hard disk drive This topic provides instructions on how to remove or install a non hot swap hard disk drive This topic applies only to server models that have non hot swap hard disk drive s installed See Features on page 7 for more information about the supported non hot swap hard disk drives Chapter 6 Installing removing or replacing hardware 123 For a list of the ThinkServer hard disk drive options go to http www lenovo com thinkserver Click the Products tab and then click Options gt ThinkServer Hard Drives to view the informatio
109. bles that might impede your operation 0 2 W DY Touch the static protective package that contains the RAID card to any unpainted surface on the outside of the server Then take the RAID card out of the package Note Carefully handle the RAID card by its edges 7 The RAID card is a kind of PCI card See Installing a PCI card on page 93 and follow those instructions to install the RAID card 8 Connect cables depending on your specific server configuration See Connecting cables on page 38 What to do next To work with another piece of hardware go to the appropriate section To complete the installation go to Completing the parts replacement on page 168 Then configure RAID for your server See Configuring RAID on page 71 Removing the RAID card Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to remove the RAID card Attention Make sure that you back up your data before removing the RAID card because you might need to reconfigure RAID and reinstall the operating system after removing the RAID card If you remove the RAID card you will lose the advanced SATA SAS hardware RAID functions Also a specific RAID card is required for server models with more than four hard disk drives or models that use SAS hard disk drives Before you begin print all the related
110. by model Four memory slots installed memory modules vary by model For more information about El to Ell see Front view of the server on page 15 Note The DIT module 15 only available in some models and the DIT panel also varies by model See DIT module on page 18 e Each of the hard disk drive bay is used for installing a 3 5 inch non hot swap hard disk drives Note The number of the installed hard disk drives varies by model For information about the supported expansion card see System board components on page 42 Chapter 3 Product overview 31 Depending on the model your server might come with a screw secured non hot swap power supply or hot swap redundant power supply module s For more information about the memory modules see Memory module installation rules on page 90 Hot swap hard disk drive status LEDs This topic applies only to server models with hot swap hard disk drives Note Depending on the model your server might look slightly different from the illustrations in this topic Each hot swap hard disk drive has two status LEDs on the front Unlock and open the front door to gain access to the hard disk drives and view the status LEDs O00000 000080 Figure 15 3 5 inch hot swap hard disk drive status LEDs 32 ThinkServer Hardware Maintenanc
111. cal drive problems 173 PC Doctor for DOS 172 POST error codes 177 status and diagnostic LEDs 171 System event log 172 ThinkServer EasyStartup program problems 172 troubleshooting procedure 171 turning off the server 53 turning on the server 53 T V gloss statement 226 U updating firmware 80 server configuration 170 the BIOS 68 updating or recovering the BIOS 67 using documentation 213 EasyUpdate Firmware Updater program 81 passwords 65 Setup Utility program 55 ThinkServer EasyStartup program 69 V video subsystem features 9 viewing information Setup Utility program 55 virtual drive initializing 77 W Web site compatible options 89 working inside the server with the power on guidelines 85 Copyright Lenovo 2011 233 234 ThinkServer Hardware Maintenance Manual lenovo
112. ce that is designated for the server e FRUs FRUs must be replaced only by trained service technicians Notes 1 Before servicing a Lenovo product be sure to read and understand the Safety information on page iii 2 For information about the terms of warranty refer to the Warranty and Support Information on the documentation DVD that comes with the server The Warranty and Support Information is also available on the Lenovo Web site at http www lenovo com ThinkServerUserGuides To obtain the most up to date information about the server go to http www lenovo com thinkserver Lenovo maintains pages on the World Wide Web where you can get the latest technical information and download documentation or device drivers and updates To access the Lenovo Support Web site go to http support lenovo com Server documentation This topic provides general descriptions of the various documentation for your server and instructions on how to obtain all the documentation Copyright Lenovo 2011 1 Printed documents The following documents are printed out and contained in your server package Read First This is a multilingual document you should read first This document guides you to read the complete warranty support and safety information on the documentation DVD that comes with your server before using the product This document also provides information about how to find the most up to date information on the
113. ch as the disc or hard disk drive as expected do one of the following to select the startup device you want Note Not all discs hard disk drives or other removable devices are bootable To select a temporary startup device do the following Note Selecting a startup device using the following method does not permanently change the startup sequence 1 Turn on or restart your server 2 When you see the logo screen press F12 to display the boot menu The boot device selection window opens If your server is connected to a network and you want to start up the server from the network press F10 3 In the boot device selection window use the up and down arrow keys on the keyboard to switch between the selections Press Enter to select the device of your choice Then the server will start up from the selected device To view or permanently change the configured startup device sequence do the following 1 Start the Setup Utility program See Starting the Setup Utility program on page 55 2 On the Boot Options menu follow the instructions on the screen to set the startup device for Boot Option 1 to Boot Option 5 depending on your needs You can also set the boot priority for various devices See Boot Options menu on page 62 66 ThinkServer Hardware Maintenance Manual 3 Press 10 to save settings and exit the Setup Utility program The server will follow the startup device sequence you have set each time you turn on the server
114. ckplane remove the four screws that secure the backplane and then remove the backplane from the hard disk drive cage Figure 72 Removing the 3 5 inch hot swap hard disk drive backplane e For the 2 5 inch hot swap hard disk drive backplane remove the six screws that secure the backplane and then remove the backplane from the hard disk drive cage Figure 73 Removing the 2 5 inch hot swap hard disk drive backplane 10 Touch the static protective package that contains the new hot swap hard disk drive backplane to any unpainted surface on the outside of the server Then remove the new backplane from the package Note Carefully handle the backplane by its edges 11 Position the new backplane on the hard disk drive cage so that the screw holes in the new backplane are aligned with the corresponding holes in the hard disk drive cage Then do one of the following depending on the hard disk drive cage e For the 3 5 inch hot swap hard disk drive cage install the four screws to secure the backplane on the cage Figure 74 Installing the 3 5 inch hot swap hard disk drive backplane Chapter 6 Installing removing or replacing hardware 135 e For the 2 5 inch hot swap hard disk drive cage install the six screws to secure the backplane on the cage Figure 75 Installing the 2 5 inch hot swap hard disk drive backplane 12 Slide the hard disk drive cage into the chassis from the front until it snaps into position Note The f
115. cts the bay 2 first Save the shield for future use Figure 81 Installing a hot swap redundant power supply module 4 If you are instructed to return the old hot swap redundant power supply module follow all packaging instructions and use any packaging materials that are supplied to you for shipping 5 To work with another piece of hardware go to the appropriate section Replacing the power distribution board and cage assembly Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to replace the power distribution board and cage assembly This topic applies only to server models that come with hot swap redundant power supply modules CAUTION Hazardous moving parts Keep fingers and other body parts away Chapter 6 Installing removing or replacing hardware 143 CAUTION Never remove the cover on a power supply or any part that has the following label attached Hazardous voltage current and energy levels are present inside any component that has this label attached There are no serviceable parts inside these components If you suspect a problem with one of these parts contact a service technician Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Depending on t
116. d components on page 42 13 Properly route the signal cables of the new front panel board assembly according to your note You might need to secure the signal cables with cable clips or ties in the chassis 14 Reinstall the front system fan s See Replacing the front system fan on page 149 15 Reinstall the front bezel See Removing and reinstalling the front bezel on page 87 16 If you are instructed to return the old front panel board assembly follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To complete the replacement go to Completing the parts replacement on page 168 Replacing the front system fan Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to replace the front system fan Chapter 6 Installing removing or replacing hardware 149 Depending on the model your server might come with one or two front system fans See Server components on page 25 to locate the front system fan s installed in your server model Note The front system fan 2 is only available in server models with five to eight 3 5 inch hot swap hard disk drives installed The front system fan 2 should only be factory installed Lenovo does not support u
117. d disk drive backplane s 6 Release the power supply assembly cables from the cable clips and ties in the chassis 7 Remove the four screws Ell at the rear of the chassis that secure the power supply assembly Then push the power supply assembly from the rear until it is released from the metal retaining tab El Figure 77 Releasing the non hot swap power supply assembly 198 ThinkServer Hardware Maintenance Manual 8 Pivot the power supply assembly a little bit in the direction as shown and then lift it out of the chassis ON gt LZ SS aN SR gt 2 CCS NY Figure 78 Removing the non hot swap power supply assembly 9 Touch the static protective package that contains the new power supply assembly to any unpainted surface on the outside of the server Then remove the new power supply assembly from the package and ensure that the new power supply assembly is the correct replacement See Features on page 7 for information about the supported power supply assemblies Chapter 6 Installing removing or replacing hardware 139 10 Install the new power supply assembly into the chassis so that the four screw holes in the new power supply assembly are aligned with the corresponding holes marked with A in the rear of the chassis Then install the four screws to secure the new power supply assembly in place Note Use only screws provided by Lenovo
118. d to you for shipping Figure 48 Removing the iKVM key What to do next To work with another piece of hardware go to the appropriate section To complete the removal procedure go to Completing the parts replacement on page 168 108 ThinkServer Hardware Maintenance Manual Installing or removing the TPM module This topic provides instructions on how to install or remove the TPM module The TPM module is a security chip designed by the Trusted Computing Group TCG to provide a hardware method of data encryption It stores passwords encryption keys and digital certificates to help provide security solutions and protect the computer Installing the TPM module Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to install the TPM module Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Use any documentation that comes with the TPM module and follow those instructions in addition to the instructions in this topic To install the TPM module do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover
119. d wires When working inside the server you might find some tasks easier if you lay the server on its side Handling static sensitive devices Attention Do not open the static protective package that contains the new part until the defective part has been removed from the server and you are ready to install the new part Static electricity although harmless to you can seriously damage server components and parts When you handle server parts and components take these precautions to avoid static electricity damage Limit your movement Movement can cause static electricity to build up around you The use of a grounding system is recommended For example wear an electrostatic discharge ESD wrist strap if one is available Make sure that you work in an ESD safe area Always carefully handle the parts and other components such as PCI cards memory modules system boards and microprocessors by its edges or its frame Do not touch solder joints pins or exposed circuitry Do not leave the device where others can handle and damage it Before you replace a new part touch the static protective package containing the new part to an unpainted metal part of the server for at least two seconds This reduces static electricity from the package and your body Remove the new part from the static protective package and directly install it in the server without placing it on any other surface If it is hard for you to do this
120. derstand all caution and danger statements in this document before you perform the procedures Read and understand any additional safety information that is included with the server or optional device before you install remove or replace the device iv ThinkServer Hardware Maintenance Manual Statement 1 AA DANGER Electrical current from power telephone and communication cables is hazardous To avoid a shock hazard Do not connect or disconnect any cables or perform installation maintenance or reconfiguration of this product during an electrical storm Connect all power cords to a properly wired and grounded electrical outlet Connect to properly wired outlets any equipment that will be attached to this product When possible use one hand only to connect or disconnect signal cables Never turn on any equipment when there is evidence of fire water or structural damage Disconnect the attached power cords telecommunications systems networks and modems before you open the device covers unless instructed otherwise in the installation and configuration procedures Connect and disconnect cables as described in the following table when installing moving or opening covers on this product or attached devices To connect To disconnect Turn everything OFF Turn everything OFF First attach all cables to devices First remove power cords from outlet Attach signal cables to connectors Remove signal cable
121. device to protect against personal injury Statement 10 A CAUTION The following label indicates a sharp edge hazard A EN Copyright Lenovo 2011 vii Statement 11 A CAUTION The following label indicates a potential heat hazard A Statement 12 AA DANGER Overloading a branch circuit is a potential fire hazard and a shock hazard under certain conditions To avoid these hazards ensure that your system electrical requirements do not exceed branch current ratings at the installation site Statement 13 A CAUTION Ensure that the rack is secured properly to avoid tipping when the server unit is extended on the rails Statement 14 A CAUTION Some accessory or option board outputs exceed Class 2 or limited power source limits You must install the appropriate interconnecting cabling in accordance with your local electrical code requirements Statement 15 AA CAUTION The power control button on the device may put the device in standby mode instead of turning off the device In addition the device might have multiple connections to dc power To remove all electrical current from the device ensure that all connections to dc power are disconnected at the dc power input terminals Em 4 viii ThinkServer Hardware Maintenance Manual Statement 16 AA CAUTION To reduce the risk of electric shock or energy hazards This equipment must be install
122. disk drive bays when installing a hard disk drive See Server components on page 25 to locate the hard disk drive bays in your server For RAID configuration the hard disk drives must be the same type with the same capacity if they are within a single RAID array For more information see Configuring RAID on page 71 For hard disk drives with different capacities install the hard disk drive with the lowest capacity first Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Notes 1 Depending on the model your server might come with 3 5 inch hot swap hard disk drive s or 2 5 inch hot swap hard disk drive s The illustrations in this topic are based on server models with four 3 5 inch hot swap SATA or SAS hard disk drives For other models the replacement procedure is the same 2 Depending on the model your server might look slightly different from the illustrations in this topic Chapter 6 Installing removing or replacing hardware 119 3 Use any documentation that comes with the hot swap hard disk drive and follow those instructions in addition to the instructions in this topic To install or replace a hot swap hard disk drive do the following 1 Use the front door key to unlock the front door and then use the front door handle El to pivot the front door to the open position Figure 58 Opening the f
123. door handle J to pivot the front door to the open position Figure 62 Opening the front door of the server Chapter 6 Installing removing or replacing hardware 125 3 non hot swap hard disk drive s are installed the lower hard disk drive cage and are protected by an EMlI protective panel Press the small tab Ell on the EMI protective panel from the bottom and then pivot the EMI protective panel upward to remove it from the chassis and gain access to the non hot swap hard disk drive s Figure 63 Removing the EMI protective panel Remove the server cover See Removing the server cover on page 85 Remove the front system fan 1 See Replacing the front system fan on page 149 Locate the appropriate non hot swap hard disk drive See Server components on page 25 Then disconnect the SATA signal cable and the power cable from the rear of the non hot swap hard disk drive 126 ThinkServer Hardware Maintenance Manual 7 Insert two fingers into the holes in the two tabs on the front of the blue bracket Then press the tabs towards each other and carefully slide the non hot swap hard disk drive out of the front of the chassis LET x gt Figure 64 Sliding the non hot swap hard disk drive out of the bay 8 Flex the sides of the blu
124. drive non hot swap 250 GB SATA enterprise 7200 rpm 3 Gb s 3 5 inch drive assembly MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Hard disk drive non hot swap 500 GB SATA enterprise 7200 rpm 3 Gb s 3 5 inch drive assembly MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO Dresd MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO 03X3678 Hard disk drive non hot swap 1 TB SATA enterprise 7200 rpm 3 Gb s 3 5 inch drive assembly MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO Genes MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Hard disk drive non hot swap 2 TB SATA enterprise 7200 rpm 3 Gb s 3 5 inch drive assembly MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 959515 0391 0392 0393 0441 Chapter 8 FRU lists 183 Hard disk drive hot swap 300 5 5 enterprise 6 Gb s cache 3 5 inch drive assembly MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Hard disk drive hot swap 450 GB SAS enterprise 6 Gb s xx MB cache 3 5 inch drive assembly MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 0391 0392 0393 0441 03 3916 Hard disk drive hot swap 600 GB 5 5 enterprise 6 Gb s MB cache 3 5 inch drive assembly
125. e 69 The device drivers for onboard Ethernet controllers are also available for download at http support lenovo com To download the drivers click Download Drivers amp Software and then follow the instructions on the Web page Updating the firmware The firmware in the server is periodically updated and is available for download on the Lenovo Support Web site Go to http support lenovo com click Download Drivers amp Software and then follow the instructions on the Web page to check for the latest level of firmware such as the BIOS and BMC updates and device drivers When you replace a device in the server you might have to either update the server with the latest version of the firmware that is stored in memory on the device or reflash the BIOS the BMC firmware and the FRU SDR from a disc image 80 ThinkServer Hardware Maintenance Manual Using the Firmware Updater program The Firmware Updater program enables you to maintain your system firmware up to date and helps you avoid unnecessary outages To update your system firmware using the Firmware Updater program do the following Note Lenovo maintains the Support Web site by making changes and improvements periodically The actual procedure might vary slightly from what is described in this topic 1 Go to the Lenovo Support Web site at http support lenovo com 2 Click Download Drivers amp Software and follow the instructions on the Web page to locate the
126. e Manual 0000 0000 0000 Figure 16 2 5 inch hot swap hard disk drive status LEDs Hard disk drive activity LED El Hard disk drive RAID status LED Off Off The hard disk drive has failed or is not present On green Off The hard disk drive is present but not in use Blinking green The hard disk drive is active and data is being transferred On green Blinking rapidly about four flashes The RAID controller is identifying the per second amber hard disk drive On green On amber The RAID array has failed and cannot recover You need to recreate a new array Blinking green Blinking slowly about one flash per The hard disk drive is being rebuilt second amber RAID card This topic provides information to help you locate the connectors on a RAID card if you have one installed in the PCI E slot 3 on the system board See System board components on page 42 Chapter 3 Product overview 33 Some server models come with a required RAID card to provide advanced SATA SAS hardware RAID functions to the server You can also purchase the RAID card from Lenovo and install it into models that support the RAID card to get advanced SATA SAS hardware RAID functions See Installing or removing the RAID card on page 98 Note For server models with more than four hard disk drives or models that use SAS hard disk drives there must be a RAID card installed Option name ThinkServer 9240 8i RAID 0 1 Adapter
127. e bracket out of the chassis Store the PCI card slot bracket in the event that you later remove the PCI card and need the bracket to cover the place Note Carefully place the removed screw aside You will need the screw later to secure the PCI card in place L Figure 40 Removing a PCI card slot bracket 6 Touch the static protective package that contains the new PCI card to any unpainted surface on the outside of the server Then take the new PCI card out of the package Note Carefully handle the PCI card by its edges 94 ThinkServer Hardware Maintenance Manual 7 Position the new PCI card on the PCI card slot for which you have removed the slot bracket and then carefully press the PCI card straight down until it is securely seated in the slot Install the screw to secure the PCI card in place Note Your PCI card might look different from the following illustration depending on the specific type Figure 41 Installing a PCI card 8 Depending on the type of the PCI card you might need to connect any required cables Refer to the documentation that comes with the PCI card for specific information What to do next To work with another piece of hardware go to the appropriate section To complete the installation go to Completing the parts replacement on page 168 Removing a PCI card Attention Do not open your server or attempt any repair before reading and understanding the Safety i
128. e bracket to remove the non hot swap hard disk drive from the bracket Save the bracket for future use Note Do not touch the circuit board on the hard disk drive 9 Reinstall the front system fan 1 See Replacing the front system fan on page 149 Chapter 6 Installing removing or replacing hardware 127 10 Align the top edge of the EMI protective panel with the top side of the hard disk drive cage and then pivot the EMI protective panel down until it snaps into position WS A SS S SN 55 SA SS SS 8 pes 5 SS SESS RSS W oeo SS Figure 65 Installing the EMI protective panel 11 Disconnect the SATA cable for the removed non hot swap hard disk drive from the system board and save the cable for future use 12 Close and lock the front door 13 If you are instructed to return the old non hot swap hard disk drive follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To complete the removal procedure go to Completing the parts replacement on page 168 Then you might need to reconfigure RAID for your server See Configuring RAID on page 71 Installing a non hot swap hard disk drive Attention D
129. e cables 40 ThinkServer Hardware Maintenance Manual If you are connecting the SATA hard disk drives to the system board use the 450 mm 17 72 inches mini SAS signal cable with four SATA ports and one Serial General Purpose Input Output SGPIO port Connect the mini SAS connector J to the mini SAS signal cable connector on the 3 5 inch hot swap hard disk drive backplane and connect the four SATA ports to the SATA connector 0 to SATA connector on the system board Then connect the SGPIO port J to the SATA SGPIO connector on the system board Notes 1 The number on the label for each of the four SATA signal cables indicates the sequence when you are connecting the cables to the corresponding SATA connectors 0 3 on the system board SATA signal cable label System board SATA connector 2 f you connect the SATA hard disk drives to the system board you can configure RAID using the configuration utility for the onboard SATA software RAID See Configuring the onboard SATA software RAID on page 74 Figure 25 Mini SAS signal cable with four SATA ports and one SGPIO port The RAID card provides advanced SATA SAS RAID configurations If you are using SAS hot swap hard disk drives you must have the RAID card for connecting the SAS hard disk drives To connect the hard disk drives to the installed RAID card the following cables that come with the RAID card are required Note The option package for the RAID card is designed
130. e might be changes that are required after a product has been sold Lenovo or your reseller will make selected Engineering Changes ECs that apply to your hardware available The warranty does not cover the following Replacement or use of parts not manufactured for or by Lenovo or non warranted Lenovo parts Identification of software problem sources Configuration of the Unified Extensible Firmware Interface UEFI as part of an installation or upgrade Changes modifications or upgrades to device drivers Installation and maintenance of network operating systems NOS Installation and maintenance of application programs For the warranty type and duration for your product refer to the Warranty and Support Information on the documentation DVD that comes with you server You must retain your proof of purchase to obtain warranty service For warranty service consult the worldwide Lenovo Support telephone list Telephone numbers are subject to change without notice The most up to date telephone list for Lenovo Support is always available on the Web site at http www lenovo com support phone If the telephone number for your country or region is not listed contact your Lenovo reseller or Lenovo marketing representative Using other services If you travel with a Lenovo notebook computer or relocate your computer to a country where your desktop notebook or server machine type is sold your computer might be eligible for International Warranty
131. e system board 42 ThinkServer Hardware Maintenance Manual 37 I 5 EE EJ ER m EL m B D 0 4 I _ L 1 m EJ KHH Ej mum Figure 27 System board components Ell Power Management Bus PMBus connector connector Internal dual port USB 2 0 connector 2 EH 4 pin system fan 1 connector PCI Express x4 card slot PCI E slot 2 Chapter 3 Product overview 43 El PMBus connector The BMC can read the power supply status registered through PMBus You do not need to connect any device to the PMBus connector This connector is kept for power management in models with redundant power supply modules The function of the PMBus connector is not available for models with a Screw secured non hot swap power supply E TPM connector Used to connect a TPM module which is a security chip to protect your server and strengthen server security See Installing or removing the TPM module on page 109 E
132. ed RE Heat sink and fan assembly Hard disk drive bay 3 System board disk drive bay 2 Rear system fan Hard disk drive bay 1 Power supply Hard disk drive bay 0 Four memory slots installed memory modules vary by model For more information about Eg to see Front view of the server on page 15 Chapter 3 Product overview 29 Note The DIT module Ellis only available in some models and the DIT panel also varies by model See DIT module on page 18 e There is a 3 5 inch hot swap hard disk drive or a dummy hard disk drive tray installed in each hard disk drive bay H to Note The number of the installed hard disk drives varies by model For the vacant drive bay there is a dummy hard disk drive tray to cover the place For information about the supported expansion card see System board components on page 42 Depending on the model your server might come with a screw secured non hot swap power supply or hot swap redundant power supply module s For more information about the memory modules see Memory module installation rules on page 90 30 ThinkServer Hardware Maintenance Manual The following illustration shows the components of the server with up to four 3 5 inch non hot swap hard disk drives ES Front system fan 1 System board battery Expansion card varies
133. ed by trained service personnel in a restricted access location as defined by your local electrical code and the latest edition of IEC 60950 Connect the equipment to a reliably earthed safety extra low voltage SELV source An SELV source is a secondary circuit that is designed so that normal and single fault conditions do not cause the voltages to exceed a safe level 60 V direct current e The branch circuit overcurrent protection must be rated in accordance with local electrical code requirements Use 1 3 mm or 16 American Wire Gauge AWG copper conductor only not exceeding 3 meters in length Torque the wiring terminal screws to 1 4 newton meters or 12 inch pounds Provide a readily available approved and rated disconnect device in the field wiring Statement 17 A CAUTION This product contains a Class 1M laser Do not view directly with optical instruments Statement 18 A CAUTION Do not place any object on top of rack mounted products Statement 19 A CAUTION Hazardous moving parts Keep fingers and other body parts away Copyright Lenovo 2011 ix Statement 20 A CAUTION A lithium ion battery is provided To avoid possible explosion do not burn the battery Replace the battery only with the Lenovo approved part Recycle or discard the battery as instructed by local regulations X ThinkServer Hardware Maintenance Manual Chapter 1 General information This chapter provides
134. edundant power supply module is working properly When the red LED is lit it indicates that the hot swap redundant power supply module has failed The hot swap redundant power supply modules help you avoid significant interruption to the operation of the system when a power supply module fails and you can replace a hot swap redundant power supply module without turning off the server Note To maintain the EMI integrity and cooling of the server install a new hot swap redundant power supply module as soon as you remove the failing one or cover the other bay with a shield if you just use one module to provide power CAUTION Hazardous moving parts Keep fingers and other body parts away CAUTION Never remove the cover on a power supply or any part that has the following label attached Hazardous voltage current and energy levels are present inside any component that has this label attached There are no serviceable parts inside these components If you suspect a problem with one of these parts contact a service technician Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Notes 1 Your hot swap redundant power supply module might look slightly different from the illustrations in this topic 2 Use any documentation that comes with the new hot swap redundant power supply module and follow those instructions in addition to the instructions in this t
135. eeds vary and are often less than the possible maximum When referring to processor storage real and virtual storage or channel volume KB stands for 1 024 bytes MB stands for 1 048 576 bytes and GB stands for 1 073 741 824 bytes When referring to hard disk drive capacity or communications volume MB stands for 1 000 000 bytes and GB stands for 1 000 000 000 bytes Total user accessible capacity can vary depending on operating environments Maximum internal hard disk drive capacities assume the replacement of any standard hard disk drives and population of all hard disk drive bays with the largest currently supported drives that are available from Lenovo Maximum memory might require replacement of the standard memory with an optional memory module Lenovo makes no representations or warranties with respect to non Lenovo products Support if any for the non Lenovo products is provided by the third party not Lenovo Some software might differ from its retail version if available and might not include user manuals or all program functionality Polyvinyl Chloride PVC cable and cord notice WARNING Handling the cord on this product or cords associated with accessories sold with this product will expose you to lead a chemical known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling Recycling information Lenovo encourages owners of information technology IT
136. elf starting bootable ThinkServer EasyStartup DVD The user guide for the program is also on the DVD and can be accessed directly from the program interface If you do not have a ThinkServer EasyStartup DVD available you can also download an ISO image from the Lenovo Support Web site and make a disc by yourself To download the ThinkServer EasyStartup program image and burn it into a disc do the following Note Lenovo maintains the Support Web site by making changes and improvements periodically The actual procedure might vary slightly from what is described in this topic 1 Go to the Lenovo Support Web site at http support lenovo com 2 Click Download Drivers amp Software and follow the instructions on the Web page to locate the ThinkServer EasyStartup program 3 Download the ISO image for the ThinkServer EasyStartup program and the installation instructions in a TXT file 4 Use any DVD burning software to create a bootable disc with the ISO image 5 Print the TXT file that contains the installation instructions and follow the instructions to start the ThinkServer EasyStartup program Chapter 5 Configuring the server 69 Features of the ThinkServer EasyStartup program This topic lists the features of the ThinkServer EasyStartup program The ThinkServer EasyStartup program has the following features Contained in a self starting bootable DVD Easy to use language selectable interface Integrated help system and us
137. en The hard disk drive is active and data is being transferred EX NIC 1 status LED NIC 2 status LED The two NIC status LEDs indicate the LAN status for the Ethernet connector 1 and Ethernet connector 2 on the rear panel of the server System status LED The system status LED helps you to determine if there are any system errors Off None The server is off or the server is on and is working correctly Front USB connector 1 Front USB connector 2 Used to attach a device that requires a USB connector such as a USB keyboard a USB mouse a USB scanner or a USB printer If you have more than six USB devices you can purchase a USB hub which you can use to connect additional USB devices DIT module This topic provides information about the DIT module and the diagnostic LEDs on the panel of the DIT module 18 ThinkServer Hardware Maintenance Manual Note The DIT module is only available in some models The following illustration shows the location of the DIT module and the diagnostic LEDs on the DIT panel in the front of the server Depending on the model your server might look slightly different from the following illustration Figure 5 DIT panel Ell Microprocessor error LED Ambient temperature over limit LED E Fan error LED Fan error LED El Memory module error LED Power supply error LED only available on models with redundant power supply modul
138. eplacement procedures for all field replaceable units FRUs parts replaced by trained service personnel as well as all CRUs Chapter 1 General information 3 4 ThinkServer Hardware Maintenance Manual Chapter 2 Server setup road This chapter provides a general road map to guide you through setting up your server The server setup procedure varies depending on the configuration of the server when it was delivered In some cases the server is fully configured and you just need to connect the server to the network and an ac power source and then you can turn on the server In other cases the server needs to have hardware features installed requires hardware and firmware configuration and requires an operating system to be installed The general procedure for setting up your server is 1 2 Unpack the server package See Server package on page 7 Install any required hardware or server option See the related topic in Chapter 6 Installing removing or replacing hardware on page 83 Connect the Ethernet cable and power cord s to the server See Rear view of the server on page 19 to locate the connectors 4 Turn on the server to verify operation See Turning on the server on page 53 Review the Unified Extensible Firmware Interface UEFI settings and customize as needed See Using the Setup Utility program on page 55 Configure RAID and install the operating system and basic drivers See Us
139. er 2 Make sure that all internal cables are routed correctly and secured by any cable clips or ties in the server Keep cables clear of the hinges and sides of the server chassis to avoid interference with reinstalling the server cover 3 If you have removed the front bezel reinstall it See Removing and reinstalling the front bezel on page 87 168 ThinkServer Hardware Maintenance Manual 4 Position the server cover on the chassis so that the rail on the bottom of the server cover engages the bottom rail on the chassis Then align the four tabs Ell on the server cover with the corresponding holes in the top edge of the chassis Pivot the server cover to close it Figure 105 Closing the server cover 5 Slide the server cover to the front of the chassis until it snaps into position Figure 106 Installing the server cover 6 Tighten the thumbscrew on the server cover to secure the server cover in place Chapter 6 Installing removing or replacing hardware 169 Note For safety consideration be sure to use tool for example screwdriver to tighten the thumbscrew and always make sure that the thumbscrew is securely installed Also do not over tighten the thumbscrew 7 Lock the server cover and server front door to ensure the security See Server locks on page 22 8 Reconnect external cables and power cord s to the server See Rear view of the server on page 19 to identify the connec
140. er Front panel Front door H Optical drive bay 2 with an optical drive installed Front door lock in some models Optical drive bay 1 with an optical drive installed Ell Front door handle Optical drive eject close button Ell Doctor Inside Technology DIT panel available in some models E Optical drive status LED Optical drive status LED Front panel For detailed information about the control connectors and status LEDs on the front panel see Front panel on page 17 Optical drive bay 2 The 5 25 inch optical drive bay 2 is for a secondary optical drive or a RDX USB drive bundle server option Some models have a secondary optical drive installed Chapter 3 Product overview 15 El Optical drive 1 Your server comes with an optical drive installed in the 5 25 inch optical drive bay 1 Optical drive eject close button Press this button to eject or close the optical drive when the server power is on Optical drive status LED The optical drive status LED is blinking in green when the optical drive is working or in the POST process Front door Front door lock You can lock the front door to protect the hard disk drive cages from unauthorized access Front door handle The front door handle helps you to open the front door EJ DIT panel The DIT panel is only available in models that come with a DIT module For more information see DIT module on page 18 16 ThinkSer
141. er guide Automatic hardware detection RAID configuration utility Device drivers provided based on the server model and detected devices Selectable partition size and file system type Support for multiple operating systems Ability to install the operating system and device drivers in an unattended mode to save time Ability to create a reuseable response file that can be used with similarly configured Lenovo servers to make future installations even faster Starting the ThinkServer EasyStartup program Th is topic provides instructions on how to start the ThinkServer EasyStartup program After you start the program and enter the main interface click User Guide for detailed information about how to use this program to help you configure the server and install an operating system To 1 start the ThinkServer EasyStartup program do the following Insert the ThinkServer EasyStartup DVD into the optical drive set the optical drive as the first startup device and start your server from the DVD in the optical drive See Selecting a startup device on page 66 Wait for the program to load Then you will be prompted for the following selections The language in which you want to view the program The language of the keyboard layout you will be using with the program Note The supported languages and keyboard layouts for the ThinkServer EasyStartup program are German English Spanish French Italian Dutch Turkish and Japan
142. erver might look slightly different from the illustration in this topic 2 The following illustration is based on five to eight 3 5 inch hot swap SATA or SAS hard disk drives with two backplanes Figure 18 Hot swap hard disk drive backplane locations Backplane for 3 5 hot swap hard disk drives This topic provides information to help you locate the connectors on a 3 5 inch hot swap hard disk drive backplane Chapter 3 Product overview 35 The following illustrations show the connectors on 3 5 inch hot swap hard disk drive backplane Figure 19 Front view of the 3 5 hot swap hard disk drive backplane Slot 0 for a 3 5 inch SATA or SAS hot swap hard El Slot 2 for a 3 5 inch SATA or SAS hot swap hard disk drive disk drive Slot 1 for a 3 5 inch SATA or SAS hot swap hard El Slot 3 for a 3 5 inch SATA or SAS hot swap hard disk drive disk drive Figure 20 Rear view of the 3 5 inch hot swap hard disk drive backplane E 8 pin power connector e For 3 5 inch hot swap hard disk drive backplane on the lower hard disk drive cage connect the P5 power connector of the power supply to the 8 pin power connector on the backplane e For 3 5 inch hot swap hard disk d
143. es HEB Error LEDs When one of these error LEDs is lit orange it indicates that the associated component has failed Ambient temperature over limit LED When this LED is lit orange it indicates that the ambient temperature is over 38 C 100 4 F Rear view of the server This topic provides information to help you locate the connectors and components on the rear of your server Chapter 3 Product overview 19 The following illustration shows the rear view of the server with a screw secured non hot swap power supply EO eye of ii Expansion card area Ethernet connector 1 RJ 45 Ethernet connector 2 RJ 45 for system management Front door key 20 ThinkServer Hardware Maintenance Manual For server models that hot swap redundant power supply module s there might be one or two power cord connectors El on the rear of the server For each hot swap redundant power supply module there might be one or two status LEDs on the power supply module near the power cord connector When the green LED is lit it indicates that the hot swap redundant power supply module is working properly When the red LED is lit it indicates that the hot swap redundant power supply module has failed Figure 7 Rear view of the server with hot swap redundant p
144. ese Your ThinkServer EasyStartup DVD might be English only In this case the keyboard layout should be English After selecting the language and keyboard layout click OK Then you will see one or more reminders or messages about configuring storage devices Click Next until you are presented with the Lenovo License Agreement Read the Lenovo License Agreement carefully In order to continue you must agree with terms by clicking Agree Then the Date and time window opens 4 Set the current date and time and click OK The Start option window opens 5 The Start option window provides the following selections e Continue to the main interface e Install the operating system using a pre existing response file e Configure RAID using a pre existing response file Read the explanations on the screen and select a desired option Then follow the instructions on the screen If this is the first time you are using the ThinkServer EasyStartup program select the option to continue to the main interface and view the compatibility notes and user guide Notes 70 ThinkServer Hardware Maintenance Manual 1 Functionality and supported operating systems vary depending on the version of the ThinkServer EasyStartup program From the main interface of the program click Compatibility notes to view the information about the RAID controllers operating systems and server configurations supported by the specific version of the program and click User Gu
145. esence Detect SPD data reading has failed 01010010 0x52 Memory initialization error The memory size is invalid or the memory modules do not match 01010011 0x53 Memory initialization error No usable memory detected 01010100 Unspecified memory initialization error 01010110 Invalid microprocessor type or speed Chapter 3 Product overview 51 POST code diagnostic LEDs POST error code Microprocessor self test failed or microprocessor cache error occurred Microprocessor microcode not found or microcode updating failed Internal microprocessor error Microprocessor initialization error North bridge initialization error South bridge initialization error 11010011 OxD3 Some architectural protocols not available 11010100 OxD4 PCI resource allocation error Out of resources Console output devices not found Console input devices not found 11011001 OxD9 Error loading Boot Option Loadlmage returned error 11011010 OxDA Boot Option failed Startlmage returned error 11011011 Flash updating failed 11011100 Reset protocol not available 52 ThinkServer Hardware Maintenance Manual Chapter 4 Turning and turning off the server This chapter provides information about turning on and turning off the server Turning on the server The server can be turned on in one of the following ways After you finish unpacking and setting up the server connect it to an ac power source Press the powe
146. evice Hard Disk Drive Optical Disk Drive Removable Device a A WwW nm Network Device The following table shows the contents of the Boot Options menu On each submenu press the Enter key to show selectable options and select a desired option by using up and down arrow keys Some items are displayed on the menu only if the server supports the corresponding features Notes e Enabled means that the function is configured Disabled means that the function is not configured e Default values are in boldface in the Selections column Boot Options menu items 62 ThinkServer Hardware Maintenance Manual _ Menuitem Selectons Comments Boot Option 1 UEFI Device Set the first startup device Hard Disk Drive Optical Disk Drive Removable Device Network Device Boot Option 2 UEFI Device Set the second startup device Hard Disk Drive Optical Disk Drive Removable Device Network Device Boot Option 3 UEFI Device Set the third startup device Hard Disk Drive Optical Disk Drive Removable Device Network Device Boot Option 4 UEFI Device Set the fourth startup device Hard Disk Drive Optical Disk Drive Removable Device Network Device Boot Option 5 UEFI Device Set the fifth startup device Hard Disk Drive Optical Disk Drive Removable Device Network Device UEFI Boot Device Priority Varies depending on the available Specify the startup priority for all the UEFI devices available UEFI devices Hard Disk Drive
147. fault tolerance If hot spare drives are available the failing drive might be rebuilt automatically without any user intervention Check Consistency This menu helps you do consistency check for the virtual drive s The consistency check verifies the correctness of the data on virtual drive s that use RAID 1 5 and 10 The following table shows the various menus and items in the LSI Software RAID Configuration Utility program On each menu press the Enter key to show selectable options and select a desired option by using up and down arrow keys or type desired values from the keyboard directly Chapter 5 Configuring the server 75 Menuitem Submenuitem Comments Configure Easy Configuration Create physical arrays An array will automatically become a virtual drive New Configuration Clear the existing configuration and start a new configuration View Add Configuration View the existing configuration or add a new configuration Clear Configuration Clear the existing configuration Select Boot Drive Select a boot virtual drive Varies by configuration Initialize virtual drives Adapter Set adapter related parameters such as rebuild rate consistency check rate auto rebuild and so on Virtual Drive Set virtual drive parameters Physical Drive Set physical drive parameters such as creating a hot spare drive for the virtual drive making a failing drive as online changing a drive state and viewing the specifications
148. ffen kunnen hebben op het milieu en de volksgezondheid tot een minimum te beperken Voor meer informatie over WEEE gaat u naar http www lenovo com lenovo environment WEEE meerkningen Waste Electrical and Electronic Equipment gaelder kun for lande i EU samt Norge Udstyr maerkes i henhold til EU s direktiv 2002 96 EF om affald af elektrisk og elektronisk udstyr WEEE Direktivet fastl gger de rammer der g lder for returnering og genbrug af brugt udstyr i EU Maerkaten p seettes forskellige produkter for at angive at produktet ikke smides det er udtjent men skal genvindes i henhold til dette direktiv Brugere af elektrisk og elektronisk udstyr der er m rket med WEEE meerket som angivet i Bilag IV til WEEE direktivet ma ikke bortskaffe brugt som usorteret husholdningsaffald men skal bruge den indsamlingsordning der er etableret sa WEEE kan returneres genbruges eller genvindes Form let er at minimere den eventuelle p virkning af milj et og menneskers sundhed som f lge af tilstedev relsen af skadelige stoffer Der er flere oplysninger om affald af elektrisk og elektronisk udstyr pa adressen http www lenovo com lenovo environment S hk ja elektroniikkalaiteromu Waste electrical and electronic equipment WEEE merkint koskee vain Euroopan unionin EU j senmaita ja Norjaa S hk ja elektroniikkalaitteet merkit n Euroopan parlamentin ja neuvoston direktiivin 2002 96 EY mukaisesti Kyse
149. fic model some features might vary or not be available For information about your specific model use the Setup Utility program See Viewing information in the Setup Utility program on page 55 Copyright Lenovo 2011 7 Microprocessor Your server comes with one of the following microprocessors internal cache size varies by model Intel Xeon quad core microprocessor e Intel Xeon dual core microprocessor e Intel Core i3 microprocessor For a list of the ThinkServer microprocessor options go to http www lenovo com thinkserver Click the Products tab and then click Options gt ThinkServer Processors to view the information Memory Your server supports up to four double data rate 3 unbuffered dual inline memory modules DDR3 UDIMMs with Error Checking and Correcting ECC technology e Supports 2 GB and 4 GB 1333 MHz DDR3 UDIMMs e Single rank or dual rank Minimum system memory 2 GB only one 2 GB memory module installed in the DIMMA2 slot e Maximum system memory 16 GB one 4 GB memory module installed in each of the four memory slots For more information see System board components on page 42 and Memory module installation rules on page 90 Power supply Your server comes with one of the following power supply configurations One screw secured non hot swap 400 watt power supply 80 Plus Bronze Compliant and universal input One or two hot swap 450 watt redundant power supply modules 80 Plus Gold C
150. g will exchange data Both computers should have the same or compatible settings This topic provides information about the security related settings on the Security menu in the Setup Utility program You can set passwords the TPM feature and other security features on the Security menu The following table shows the contents of the Security menu For each menu item press the Enter key to show selectable options and select a desired option by using up and down arrow keys or type desired values from the keyboard directly Some items are displayed on the menu only if the server supports the corresponding features Notes Enabled means that the function is configured Disabled means that the function is not configured Default values are in boldface in the Selections column 60 ThinkServer Hardware Maintenance Manual Security menu items Menuitem Selections Comments Set Administrator Password Set an administrator password to protect against unauthorized access to your server See Using passwords on page 65 Set User Password Set a user password to protect against unauthorized access to your server See Using passwords on page 65 This item is only available after you have set an administrator password Power Reset Button Lockout Disabled If this item is set to Enabled the Enabled power switch on the front panel will be locked and the server can only be turned on remotely BIOS Write Protect Disab
151. g password use the following guidelines Have at least eight characters in length Contain at least one alphabetic character and one numeric character Not be your name or your user name Not be a common word or a common name Be significantly different from your previous passwords Besides the alphabetic characters a z and numeric characters 0 9 the server also supports characters typed using special keys on the keyboard for a password Refer to the help message on the screen when setting a password to determine the valid special characters Setting changing or deleting a password This topic provides instructions on how to set change or delete a password in the Setup Utility program To set change or delete a password in the Setup Utility program do the following 1 Start the Setup Utility program See Starting the Setup Utility program on page 55 2 On the Security menu select Set Administrator Password to set an administrator password or select Set User Password to set a user password Note The Set User Password option is only available when you have already set an administrator password Chapter 5 Configuring the server 65 3 See Password considerations on page 65 Then follow the instructions on the screen to set or change a password 4 If you want to delete a password type your current password Press Enter when you are prompted to type a new password Then press Enter to confirm the new password The
152. g position 1 and pin 2 This is the correct position for normal operation Figure 28 Default jumper setting Chapter 3 Product overview 47 The following illustration shows the status of the jumpers the system board of your server You can configure recover enable or disable some specific features of the system board by setting the jumpers Roa Sa m Figure 29 System board jumpers Clear CMOS Complementary Metal Oxide Semiconductor Recovery jumper BNC setting jumper BIOS recovery jumper Clear password jumper Manufacturing jumper reserved for the manufacturer Attention To set the jumpers you need to open the server cover Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 Ell Clear CMOS Recovery jumper Used to clear CMOS and recover your server to the factory default settings Note After clearing CMOS all your BIOS passwords
153. gelezen en begrijpt Copyright Lenovo 2011 iii Przed skorzystaniem 2 produktu nalezy zapozna sie 2 wielojezycznymi instrukcjami bezpieczenstwa znajdujacymi sie na plycie DVD 2 dokumentacja dostarczona wraz 2 produktem Antes de utilizar o produto leia atentamente as instru es de seguran a multilingues que constam no DVD de documenta o fornecido com o produto nainte de a utiliza produsul asigurati v c ati citit si inteles instructiunile de sigurant in mai multe limbi de pe DVD ul cu documentatie care insoteste produsul Fer du bruker produktet du lese og forst den flerspr klige sikkerhetsinformasjonen DVDen med dokumentasjon som f lger med produktet DVD nucke AST 2 WAARA DVD 1 2 4109 Pre nego to upotrebite proizvod obavezno paljivo proitajte i prouite viejeziko uputstvo za bezbednost dokumentacionom DVD u koji ste dobili uz proizvod Pred pouvanm produktu si pretajte viacjazyn bezpenostn pokyny na disku DVD s dokumentciou dodanom s produktom Preden za nete uporabljati izdelek pomembno da p
154. he model your server might look slightly different from the illustrations in this topic To replace the power distribution board and cage assembly do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the hot swap redundant power supply module s See Replacing a hot swap redundant power supply module on page 140 Note If your server comes with one hot swap redundant power supply module installed in the redundant power supply module bay 1 the bay number is marked on the rear of the chassis there is a shied installed on bay 2 to protect the empty bay Remove the shield and save it for future use Remove the server cover See Removing the server cover on page 85 Lay the server on its side for easier operation Remove the front system fan s See Replacing the front system fan on page 149 Note down the cable routing and connection Then disconnect the power cables of the power distribution board and cage assembly from the system board and all drives For server models with hot swap hard disk drives you also need to disconnect the power cable s from the hot swap hard disk drive backplane s 7 Release the power cables of the power distribution board and cage assembly from the cable clips and ties in the chassis 144 ThinkServe
155. he server 2 Use the front door key to unlock the front door and then use the front door handle pivot the front door to the open position Figure 66 Opening the front door of the server Chapter 6 Installing removing or replacing hardware 129 3 non hot swap hard disk drive s are installed the lower hard disk drive cage and are protected by an EMlI protective panel Press the small tab the EMI protective panel from the bottom and then pivot the EMI protective panel upward to remove it from the chassis and gain access to the non hot swap hard disk drive bays Figure 67 Removing the EMI protective panel Remove the server cover See Removing the server cover on page 85 Remove the front system fan 1 See Replacing the front system fan on page 149 Locate the appropriate non hot swap hard disk drive bay See Server components on page 25 Touch the static protective package that contains the new non hot swap hard disk drive to any unpainted surface on the outside of the server Then take the new non hot swap hard disk drive and the signal cable out of the package oo Note Do not touch the circuit board on the hard disk drive 190 ThinkServer Hardware Maintenance Manual 8 Install the new non hot swap hard disk drive into a blue bracket by flexing the sides of the bracket and aligning pin
156. he server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 3 Lay the server on its side for easier operation 4 Locate an appropriate PCI card slot on the system board for installing the Ethernet card You can install the Ethernet card to the PCI E slot 2 or PCI E slot 3 that supports a card with 167 mm 6 57 inches in length See System board components on page 42 to identify the different types of PCI card slots in your server 5 Remove any parts or disconnect any cables that might impede your operation 6 Touch the static protective package that contains the Ethernet card to any unpainted surface on the outside of the server Then take the Ethernet card out of the package Note Carefully handle the Ethernet card by its edges 7 The Ethernet card is a kind of PCI card See Installing a PCI card on page 93 and follow those instructions to install the Ethernet card What to do next To work with another piece of hardware go to the appropriate section To complete the installation go to Completing the parts replacement on page 168 Then continue with the following procedure to install the Ethernet card driver if you are using a Windows operating system On Linux operating systems you do not need to install any device driver for the Ethernet card On Windows operating systems d
157. he server cover See Completing the parts replacement on page 168 8 Connect the server to an ac power source and then follow the installation instructions for the BIOS update utility program to start the server from the recovery image The recovery window opens 9 Press Enter to start the recovery process After the recovery process is completed your server will automatically turn off 10 Repeat step 2 through step 5 11 Move the BIOS recovery jumper back to the normal position pin 1 and pin 2 12 Reinstall any parts or reconnect any cables and reinstall the server cover See Completing the parts replacement on page 168 13 Connect the server to an ac power source and turn on the server The BIOS settings become the default settings of the updated BIOS version You need to check and configure the BIOS settings for your specific needs See Using the Setup Utility program on page 55 Using the ThinkServer EasyStartup program This topic guides you to use the ThinkServer EasyStartup program to set up and configure your server The ThinkServer EasyStartup program simplifies the process of configuring RAID and installing supported Windows and Linux operating systems and device drivers on your server The program works in conjunction with your Windows or Linux operating system installation disc to automate the process of installing the operating system and associated device drivers This program is provided with your server on a s
158. ice technician and must be performed only by a trained service technician Septem dC The optical drive is not recognized 1 Make sure that e The signal cable and connector are not damaged and the connector pins are not bent The optical drive is securely connected to the correct SATA connector on the system board and the SATA connector is enabled in the Setup Utility program See Using the Setup Utility program on page 55 All cables and jumpers if any are installed correctly The correct device driver is installed for the optical drive 2 Run any optical drive diagnostic programs if you have 3 Reinstall the optical drive and reconnect cables 4 Replace the signal cable for the optical drive Chapter 7 Troubleshooting and diagnostics 173 5 Replace the optical drive 6 Trained service technician only Replace the system board A disc is not working correctly Make sure that the disc is in the optical drive with the shiny side facing down Make sure that the disc surface is clean and not scratched Check the disc or package for regional coding You might need to purchase a disc with coding for the region where you are using the product 4 Restart the disc player program 5 Restart the server 6 Run any optical drive diagnostic programs if you have 7 Reinstall the optical drive and reconnect cables 8 Replace the signal cable for the optical drive 9 Re
159. ide to view the various functions and learn how to use the program 2 Before using the ThinkServer EasyStartup program to install an operating system make sure any external storage devices and fiber channels are configured correctly The ThinkServer EasyStartup program main interface provides the following menus on the left pane of the screen Home This menu is the welcome page that contains some general descriptions about the program and the Lenovo copyright and trademark statements Compatibility notes This menu provides information about the RAID controllers operating systems and server configurations supported by the version of the program you are using User Guide This menu provides information about the features of the program and instructions on how to use the program Hardware list This menu displays a list of hardware devices detected by the program Configure RAID This menu guides you to configure RAID or view the current RAID configuration and make changes if needed Install operating system This menu displays a series of choices and prompts to collect information required for operating system installation prepares the hard disk drive for installation and then initiates the installation process using your operating system installation disc About This menu provides the version information and legal notices Configuring RAID This topic provides information about RAID and the utility p
160. ifornia Perchlorate Information Products containing CR manganese dioxide lithium coin cell batteries may contain perchlorate Perchlorate Material special handling may apply See http www dtsc ca gov hazardouswaste perchlorate Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference To replace the system board battery do the following Note After you replace the system board battery you must reset passwords reset system date and time and reconfigure the server 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server Remove the server cover See Removing the server cover on page 85 Lay the server on its side for easier operation Locate the system board battery See Server components on page 25 a N Remove any installed PCI card that impedes your access to the system board battery See Removing a PCI card on page 95 Chapter 6 Installing removing or replacing hardware 161 6 Remove the old system board battery Figure 97 Removing the system board battery 7 Install a new system board battery Figure 98 Installing the system board battery 8 Reinstall the PCI card that has been removed
161. iguration Utility program See Starting the LSI Software RAID Configuration Utility program on page 74 2 On the main interface of the program select Objects gt Adapter gt Chk Const Rate Note Use up and down arrow keys to navigate between items and press Enter to select an option 3 Set the consistency check rate by typing a desired value from the keyboard directly Installing and using the MegaRAID Storage Manager program You can install and use the MegaRAID Storage Manager program to manage the RAID array and RAID controller in an operating system environment after configuring RAID The installation package for the MegaRAID Storage Manager program is on the ThinkServer EasyStartup DVD After you enter the operating system insert the ThinkServer EasyStartup DVD into the optical drive The installation package for the MegaRAID Storage Manager program is located in the Utilities and Others folder in the root directory of the DVD To install and use the MegaRAID Storage Manager program refer to the following chapters in the MegaRAID SAS Software User Guide on the documentation DVD that comes with your server Note Some information in these chapters might be intended for the advanced SATA SAS hardware RAID configurations and might not apply to the onboard SATA software configurations e MegaRAID Storage Manager Overview and Installation e MegaRAID Storage Manager Window and Menus e Monitoring System Events and Sto
162. in your specific situation place the static protective package of the new part on a smooth level surface and then place the new part on the static protective package Do not place the part on the server cover or other metal surface e Take additional care when handling devices during cold weather Heating reduces indoor humidity and increases static electricity System reliability guidelines To help ensure proper cooling and system reliability make sure that you follow these guidelines Each of the drive bays has a drive or a dummy tray installed or there is an electromagnetic interface EMI protective panel or EMI shield installed to protect the drive cage e f the server has redundant power each of the power supply module bay has a redundant power supply module installed or one bay has a module while the other bay is covered by a shield Leave adequate space around the server to make sure that the server cooling system works well Leave approximately 50 mm 2 inches of open space around the front and rear of the server Do not place objects in front of the fans For proper cooling and airflow install the server cover before you turn on the server Operating the server for extended periods of time more than 30 minutes with the server cover removed might damage server components 84 ThinkServer Hardware Maintenance Manual e Properly route the cables For some options such as PCI cards follow the cabling instructions tha
163. inen direktiivi m ritt Euroopan Unionin alueella k yt ss olevat palautus ja kierr tysk yt nn t WEEE merkint laitteessa osoittaa ett direktiivin ohjeiden mukaan tuotetta ei tulisi h vitt sen elinkaaren p ss vaan se tulee toimittaa uusiok ytt n K ytt jien joiden s hk ja elektroniikkalaitteissa on t m s hk ja elektroniikkalaiteromun direktiivin liitteen IV mukainen merkint tulee kierr tt kyseiset laitteet k ytett viss olevien resurssien mukaan ja varmistaa ett niist tai niiss k ytetyist materiaaleista ei aiheudu haittaa ymp rist lle tai ihmisten terveydelle S hk ja elektroniikkalaitteita ei saa h vitt sekaj tteen mukana Lis tietoja s hk ja elektroniikkalaiteromun uusiok yt st on WWW sivustossa http www lenovo com lenovo environment WEEE merket Waste Electrical and Electronic Equipment gjelder bare for land i Den europeiske union EU og Norge Utstyr merkes i henhold til EU direktiv 2002 96 EF om avfall fra elektrisk og elektronisk utstyr WEEE Direktivet fastsetter rammene for retur og resirkulering av brukt utstyr innenfor EU Dette merket benyttes p forskjellige produkter for angi at produktet ikke m kastes men m behandles i henhold til dette direktivet ved slutten av produktets levetid Brukere av elektrisk og elektronisk utstyr EEE som er merket med WEEE merket if lge vedlegg IV i WEEE direktivet m ikke kaste utstyret som usortert hushold
164. information to help you get familiar with your server and help you use configure and maintain your server e Remote Management Module User Guide This document provides information to help you use the integrated Keyboard Video and Mouse iKVM function for server remote management This document is in English only Note A ThinkServer iIKVM Remote Management Module hereinafter referred to as the iKVM key is required and this option should be installed on the iKVM key connector on the system board to enable the iKVM function 2 ThinkServer Hardware Maintenance Manual e MegaRAID SAS Software User Guide This document provides information about Redundant Array of Independent Disks RAID and how to use the utility programs to configure monitor and maintain your server RAID and related devices This document is in English only Note Refer to this document for hardware RAID information if you have a required RAID card installed in the server See Installing or removing the RAID card on page 98 For information about the onboard SATA software RAID see Configuring the onboard SATA software RAID on page 74 Document for trained service personnel only The following document is intended for trained service personnel of Lenovo and is only available in English on the Lenovo Web site at http www lenovo com ThinkServerUserGuides Hardware Maintenance Manual This document provides diagnostic information parts listing and r
165. ing the ThinkServer EasyStartup program on page 69 and Configuring RAID on page 71 Install any additional drivers needed for added features Refer to the instructions that come with the hardware option Configure Ethernet settings in the operating system by referring to the operating system help This step is not required if the operating system was installed using the ThinkServer EasyStartup program 9 Check for firmware and driver updates See Updating the firmware on page 80 Install other applications Refer to the documentation that comes with the applications that you want to install O Copyright Lenovo 2011 5 6 ThinkServer Hardware Maintenance Manual Chapter 3 Product overview This chapter provides information about the server package features specifications software programs and component locations This chapter contains the following items e Server package on page 7 e Features on page 7 e Specifications on page 12 e Software on page 12 e Locations on page 13 Server package The server package includes the server power cord s printed documentation documentation DVD and software media Figure 1 Server package Server Material box including power cord s printed documentation documentation DVD and software media Features This topic provides general information about the server features for a variety of models Depending on your speci
166. ing the ThinkServer EasyStartup program on page 69 12 ThinkServer Hardware Maintenance Manual ThinkServer EasyUpdate Firmware Updater The ThinkServer EasyUpdate Firmware Updater program hereinafter referred to as the Firmware Updater program enables you to maintain your server firmware up to date and helps you avoid unnecessary server outages The Firmware Updater program is provided on the Lenovo Support Web site For more information about downloading and using the Firmware Updater program see Updating the firmware on page 80 BIOS and BMC firmware update utility The BIOS and BMC firmware keeps updating after the shipment of the server Lenovo maintains pages on the Support Web site and provides the BIOS and BMC firmware update utility with instructions for download to help you update the BIOS and BMC firmware if needed For more information see Updating or recovering the BIOS on page 67 and or Updating the firmware on page 80 RAID configuration utilities Your server supports onboard SATA software RAID and advanced SATA SAS hardware RAID configurations if you have a required RAID card installed For detailed information see Configuring RAID on page 71 PC Doctor for DOS The PC Doctor for DOS is a diagnostic tool that you can use to test and gather information about your system in order to ensure your system is working correctly and resolve any hardware issues You can download the latest version of this diagnostic prog
167. irettiva WEEE non devono disporre di fine utilizzo EEE come rifiuto municipale non classificato ma deve essere utilizzata la procedura di classificazione disponibile per il riscatto riciclo recupero del WEEE e minimizzare qualsiasi potenziale effetto della EEE sull ambiente e sulla salute umana dovuto alla presenza di sostanze pericolose Per ulteriori informazioni sulla WEEE visitare il sito http www lenovo com lenovo environment A marca REEE Res duos de Equipamentos El ctricos e Electr nicos aplica se apenas aos Estados Membros da Uniao Europeia e Noruega Os aparelhos el ctricos dever o ser identificados em conformidade com a Directiva Europeia 2002 96 CE relativa a REEE Res duos de Equipamentos El ctricos e Electr nicos A Directiva determina enquadramento normativo relativamente devolu o e reciclagem de aparelhos el ctricos utilizados conforme aplic vel no espa o da Uni o Europeia Esta etiqueta dever ser aposta em diversos produtos para indicar que os mesmos nao poder o ser deitados fora mas sim recuperados no final da respectiva vida til de acordo com a referida Directiva Os utilizadores de equipamentos el ctricos e electr nicos EEE com a marca REEE em conformidade com o Anexo IV da Directiva REEE nao poder o deitar fora os EEE no final da respectiva vida util como lixo municipal nao separado devendo sim utilizar a estrutura de recolha que tenha sido disponibilizada para efeitos de devolu
168. ition the new front system fan on the system fan 1 mounting area of the chassis so that the three tips on the bottom of the front system fan are aligned with the corresponding holes in the mounting area Meanwhile make sure that the two posts of the front system fan are aligned with the corresponding holes in the inner side of the chassis Then carefully slide the front system fan into the chassis until it snaps into position Figure 87 Installing the front system fan Chapter 6 Installing removing or replacing hardware 151 8 Connect the new front system fan cable to the 4 system 1 connector on the system board See System board components on page 42 Note For server models with five to eight 3 5 inch hot swap hard disk drives there is a secondary front System fan installed in the front system fan 2 mounting area above the front system fan 1 mounting area The cable of the secondary front system fan is connected to the 5 pin system fan 2 connector on the system board See System board components on page 42 9 If you are instructed to return the old front system fan follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To complete the replacement go to Completing the parts replacement on page 168 Replacing the rear system fan Attention Do
169. kServer Hardware Maintenance Manual 41R3176 41R3196 41R3260 41R3224 Primary power cord Power cord Taiwan MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 41R3278 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Power cord Italy MT 0387 CTO 11G 12G MT 0388 CTO 12G 13G MT 0389 CTO 11G MT 0390 CTO 11G 12G 13G 41R3232 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO 11G 12G MT 0441 CTO 11G 12G 13G 14G 15G 16G Power cord Indonesia Laos Cambodia Vietnam Austria Belgium Croatia Czechoslovakia Finland France Germany Hungary Netherlands Norway Poland Portugal Romania Spain Sweden MT 0387 CTO MT 0388 CTO MT 0389 CTO 41R3208 MT 0390 CTO MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Power cord Denmark MT 0387 CTO 11G 12G MT 0388 CTO 12G 13G MT 0389 CTO 11G MT 0390 CTO 11G 12G 13G 41R3212 MT 0391 CTO MT 0392 CTO MT 0393 CTO 11G 12G MT 0441 CTO 11G 12G 13G 14G 15G 16G Chapter 8 FRU lists 199 Primary power cord Power cord Switzerland MT 0387 CTO 11G 12G MT 0388 CTO 12G 13G MT 0389 CTO 11G MT 0390 CTO 11G 12G 13G 41R3228 MT 0391 CTO MT 0392 CTO MT 0393 CTO 11G 12G MT 0441 CTO 11G 12G 13G 14G 15G 16G Power cord Israel MT 0387 CTO 11G 12G MT 0388 CTO 12G 13G MT 0389 CTO 11G MT 0390 CTO 11G 12G 13G 41R3236 MT 0391 CTO MT 0392 CTO MT 0393 CTO 11G 12G MT 0441 CTO 11G 12G 13G 14G 15G 16G Power cord South Africa MT 0387 CTO 11G 12G MT 0
170. kg 121 2 Ib 100 kg 220 5 Ib CAUTION Use safe practices when lifting Statement 5 AA CAUTION The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device The device also might have more than one power cord To remove all electrical current from the device ensure that all power cords are disconnected from the power source A A 2 m 1 Vi ThinkServer Hardware Maintenance Manual Statement 6 A CAUTION If you install a strain relief bracket option over the end of the power cord that is connected to the device you must connect the other end of the power cord to a power source that is easily accessible in case it needs to be disconnected Statement 7 A CAUTION If the device has doors ensure that you remove or secure the doors before moving or lifting the device to protect against personal injury The doors will not support the weight of the device Statement 8 AA CAUTION Never remove the cover on a power supply or any part that has the following label attached Hazardous voltage current and energy levels are present inside any component that has this label attached There are no serviceable parts inside these components If you suspect a problem with one of these parts contact a service technician Statement 9 A CAUTION Disconnect the hot swap fan cables before removing the fan from the
171. l power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 Chapter 6 Installing removing or replacing hardware 101 3 Lay the server on its side for easier operation 4 Locate the RAID card which is installed in the PCI E slot 3 on the system board See System board components on page 42 5 Remove any parts or disconnect any cables that might impede your operation 6 Locate the RAID 5 key on the RAID card and then remove it from the RAID card You might need to remove the RAID card first remove the RAID 5 key from the RAID card and then reinstall the RAID card See Installing or removing the RAID card on page 98 Note Carefully handle the RAID 5 key by its edges la B se FAL Figure 44 Removing the RAID 5 key from the RAID 7 f you are instructed to return the old RAID 5 key follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section e To complete the removal procedure go to Completing the parts replacement on page 168 As the hardware RAID 5 and 50 levels are not available without the RAID 5 key yo
172. l corrosives and gaseous contaminant transfer In the absence of specific limits that are set forth in this document you must implement practices that maintain particulate and gas levels that are consistent with the protection of human health and safety If Lenovo determines that the levels of particulates 220 ThinkServer Hardware Maintenance Manual or gases in your environment have caused damage to the server Lenovo may condition provision of repair or replacement of servers or parts on implementation of appropriate remedial measures to mitigate such environmental contamination Implementation of such remedial measures is a customer responsibility Table 1 Limits for particulates and gases Particulate The room air must be continuously filtered with 4096 atmospheric dust spot efficiency MERV 9 according to ASHRAE Standard 52 21 Air that enters a data center must be filtered to 99 9796 efficiency or greater using high efficiency particulate air HEPA filters that meet MIL STD 282 The deliquescent relative humidity of the particulate contamination must be more than 60 2 The room must be free of conductive contamination such as zinc whiskers Gaseous Copper Class G1 as per ANSI ISA 71 04 1985 Silver Corrosion rate of less than 300 in 30 days ASHRAE 52 2 2008 Method of Testing General Ventilation Air Cleaning Devices for Removal Efficiency by Particle Size Atlanta American Society of Heating Refrigerating and
173. layed on the right bottom pane of each screen You can also press the F1 key for general help about the keys For most items the corresponding help message is displayed on the right top pane of the screen when the item is selected If the item has submenus you can display the submenus by pressing Enter You can view the following information about your specific server model from the Setup Utility program The Main menu lists information about the BIOS version microprocessor type and core frequency memory size and system date and time e On the Advanced menu Select Processor Configuration to view the information about the installed microprocessor and its supported technologies Select Memory Configuration to view the information about the installed memory modules Select SATA Configuration Then select the desired SATA port from SATA Port0 to SATA Port5 to view the information about the installed SATA devices such as a SATA hard disk drive or an optical drive O Copyright Lenovo 2011 55 On the Server Management menu select System Information to view the information about your system including the BMC information Setup Utility program interface This topic provides information about the menus and items in the Setup Utility program Depending on the version of your system BIOS some menu or item information might differ slightly from the information in this topic The information in this topic is based on the 0 9b ve
174. le for the non hot swap hard disk drive 174 ThinkServer Hardware Maintenance Manual emm pT 8 Replace the hard disk drive A newly installed hot swap hard disk drive is not recognized Multiple hard disk drives fail Not all drives are recognized by the hard disk drive diagnostic test The server stops responding during the hard disk drive diagnostic test A hard disk drive was not detected while the operating system was being started 1 Make sure that the drive is installed into the correct drive bay Restart the server Remove the drive from the bay wait 45 seconds and reinsert the drive into the bay making sure that the drive connects to the hot swap hard disk drive backplane Run any diagnostic programs to test the hard disk drive Make sure that the hot swap hard disk drive backplane is correctly seated When it is correctly seated the drive assemblies correctly connect to the backplane without bowing or causing movement of the backplane Make sure that the cable connection is correct See Connecting cables on page 38 Reconnect the backplane power cable and repeat step 1 through step 4 Reconnect the backplane signal cable and repeat step 1 through step 4 If you suspect a problem with the backplane signal cable or the backplane a Replace the affected backplane signal cable b Replace the affected backplane Run any diagnostic programs to
175. led If you want to update or flash the Enabled BIOS make sure that this item is set to Disabled If this item is set to Enabled the BIOS will be protected from updating or flashing TPM Support Disabled Enable or disable the TPM support To use the TPM feature you need to Enabl 4 a TPM module installed in the TPM connector on the system board TPM State Disabled This item is displayed when the TPM Support is set to Enabled Set the Enabled 9277 TPM State to enable or disable the TPM function The server will restart in order to change the state of TPM Server Management menu This topic provides information about the features available on the Server Management menu in the Setup Utility program You can view system information and view or change event log settings on the Server Management menu The following table shows the contents of the Server Management menu On each submenu press the Enter key to view the information or show selectable options and select a desired option by using up and down arrow keys Some items are displayed on the menu only if the server supports the corresponding features Note Default values are in boldface in the Selections column Chapter 5 Configuring the server 61 Server Management menu items Meum 7 Submenuitem Selections Commems System Information View the information about your system including the BMC version information BMC LAN Configuration Clear all Eve
176. lenovo ThinkServer Hardware Maintenance Manual Machine Types 0387 0388 0389 0390 0391 0392 0393 0441 Note Before using the information and the product it supports be sure to read and understand the following The Read Me First that comes with your product e Safety information on page iii Appendix A Notices on page 217 Second Edition August 2011 Copyright Lenovo 2011 LIMITED AND RESTRICTED RIGHTS NOTICE If data or software is delivered pursuant a General Services Administration GSA contract use reproduction or disclosure is subject to restrictions set forth in Contract No GS 35F 05925 Contents Safety information Chapter 1 General information Introduction Server documentation Chapter 2 Server setup road map Chapter 3 Product overview Server package Features Specifications Software ThinkServer EasySlarfup ThinkServer EasyUpdate Firmware Updater BIOS and BMC firmware update utility RAID configuration utilities PC Doctor for DOS Locations Machine type model and label Front view of ines server Front panel DIT module Rear view of the server Server locks Server components Hot swap hard disk drive status LEDs RAID card Hot swap hard disk diu backplane System board components System board jumpers System board LEDs Chapter 4 Turning on and turning off the server
177. lenovo environment Le marquage des d chets d quipements lectriques et lectroniques DEEE s applique uniquement aux pays de l Union europ enne EU et la Norv ge Les appareils sont marqu s conform ment la Directive 2002 96 CE du Conseil Europ en relative aux d chets d quipements lectriques et lectroniques DEEE Cette directive applicable l ensemble des pays de l Union europ enne concerne la collecte et le recyclage des appareils usag s Ce marquage est appos sur diff rents produits pour indiquer que ces derniers ne doivent pas tre jet s mais r cup r s en fin de vie conform ment cette directive Les utilisateurs Appendix A Notices 221 d quipements lectriques et lectroniques portant le marquage DEEE conform ment l Annexe IV de la Directive DEEE ne doivent pas mettre au rebut ces quipements comme des d chets municipaux non tri s mais ils doivent utiliser la structure de collecte mise disposition des clients pour le retour le recyclage et la r cup ration des d chets d quipements lectriques et lectroniques afin de r duire tout effet potentiel des quipements lectriques et lectroniques sur l environnement et la sant en raison de la pr sence possible de substances dangereuses dans ces quipements Pour plus d informations sur les quipements lectriques et lectroniques consultez le site http www lenovo com lenovo environment Die WEEE Kennzeichnung gilt nur in L
178. m Ireland MT 0387 CTO 11G 12G MT 0388 CTO 12G 13G MT 0389 CTO 11G MT 0390 CTO 11G 12G 13G MT 0391 CTO MT 0392 CTO MT 0393 CTO 11G 12G MT 0441 CTO 11G 12G 13G 14G 15G 16G 202 ThinkServer Hardware Maintenance Manual 41R3176 41R3196 41R3260 41R3224 Secondary power Power cord Taiwan MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 41R3278 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Power cord Italy MT 0387 CTO 11G 12G MT 0388 CTO 12G 13G MT 0389 CTO 11G MT 0390 CTO 11G 12G 13G 41R3232 1 MT 0391 CTO MT 0392 CTO MT 0393 CTO 11G 12G MT 0441 CTO 11G 12G 13G 14G 15G 16G Power cord Indonesia Laos Cambodia Vietnam Austria Belgium Croatia Czechoslovakia Finland France Germany Hungary Netherlands Norway Poland Portugal Romania Spain Sweden MT 0387 CTO MT 0388 CTO MT 0389 CTO 41R3208 MT 0390 CTO MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Power cord Denmark MT 0387 CTO 11G 12G MT 0388 CTO 12G 13G MT 0389 CTO 11G MT 0390 CTO 11G 12G 13G 41R3212 MT 0391 CTO MT 0392 CTO MT 0393 CTO 11G 12G MT 0441 CTO 11G 12G 13G 14G 15G 16G Chapter 8 FRU lists 203 Secondary power cord Power cord Switzerland MT 0387 CTO 11G 12G MT 0388 CTO 12G 13G MT 0389 CTO 11G MT 0390 CTO 11G 12G 13G 41R3228 MT 0391 CTO MT 0392 CTO MT 0393 CTO 11G 12G MT 0441 CTO 11G 12G 13G 14G 15G 16G Power cord Israel MT 0387 CTO 11G 12G MT 0388
179. m after completing the operation Initializing a virtual drive This topic provides instructions on how to initialize a virtual drive using the LSI Software RAID Configuration Utility program after completing the configuration process Virtual drive initialization is the process of writing zeros to the data fields of a virtual drive and in fault tolerant RAID levels generating the corresponding parity to put the virtual drive in a ready state Initialization erases all data on the virtual drive Drive groups will work without being initialized but they can fail a consistency check because the parity fields have not been generated Notes 1 Make sure that you back up any data you want to keep before initializing a virtual drive 2 Make sure that the operating system is not installed on the virtual drive you are initializing Otherwise you need to reinstall the operating system after completing the operation To initialize a virtual drive using the LSI Software RAID Configuration Utility program do the following 1 Start the LSI Software RAID Configuration Utility program See Starting the LSI Software RAID Configuration Utility program on page 74 2 On the main interface of the program select Initialize and follow the instructions on the screen Setting a hot spare drive This topic provides instructions on how to set a physical drive as a hot spare drive using the LSI Software RAID Configuration Utility program A hot spare d
180. memory module has not been correctly installed Open the retaining clips remove the memory module and then reinstall it into the memory slot until the retaining clips are completely closed Figure 38 Installing a memory module 9 Reinstall any parts or reconnect any cables you have removed What to do next To work with another piece of hardware go to the appropriate section To complete the installation go to Completing the parts replacement on page 168 Removing a memory module Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to remove a memory module Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note To optimize system performance make sure that you consider and follow the memory module installation rules when performing the operation See Memory module installation rules on page 90 To remove a memory module do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server Remove the server cover See Removing the server cover on page 85 Lay the server on its side for easier operation
181. mini SAS signal cable with four SATA ports and one SGPIO port to enable the RAID status LEDs for hot swap hard disk drives Hard disk drive LED connector Used to connect a 2 pin 200 mm 7 87 inches RAID card to system board hard disk drive LED cable See Connecting cables on page 38 DIT module connector Used to connect the cable of the DIT module if your server has one installed EJ Internal serial connector Used to provide an optional serial connector solution with a required cable ET PCI card slot PCI slot 1 Used to install a standard 32 bit 33 MHz PCI card with 167 mm 6 57 inches in length Chapter 3 Product overview 45 PCI Express x4 card slot PCI E slot 2 This is a PCI Express x4 lane in physical PCI 2 0 x8 slot that supports a PCI Express x4 card with 167 mm 6 57 inches in length such as an Ethernet card BMC chip With the integrated BMC chip no matter what condition the server operating system is in and no matter if the server is on or off as long as the server is connected to network and an ac power source the interaction with the BMC controlled servers can be achieved through system network The user can obtain the server hardware health information and SEL and is able to conduct the operations including turning on or of the Server restarting the server locking the power switch on the front panel and so on This part of the server management is independent of the operating system and is called ou
182. model They provide the server with the ability to support two Ethernet connectors on the rear panel with 10 Mbps 100 Mbps or 1000 Mbps network connectivity For more information see Rear view of the server on page 19 Chapter 3 Product overview 9 Reliability availability and serviceability Reliability availability and serviceability hereinafter referred to as RAS are three important server design features The RAS features help you to ensure the integrity of the data stored on the server the availability of the server when you need it and the ease with which you can diagnose and correct problems Your server has the following RAS features Security features Server locks see Server locks on page 22 Administrator password and user password to help protect unauthorized access to the server see Using passwords on page 65 Trusted Platform Module TPM connector on the system board for a TPM module which is a security chip to help protect your server and strengthen server security Note The TPM module is only available in some models Remote monitoring or control by an administrator to provide protection or help Hot swap redundant power supply modules to help you avoid significant interruption to the operation of the system when a power supply module fails available in some models Basic system management features Ability to store the power on self test POST hardware test results BIOS Setup Utility prog
183. module do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server Remove the server cover See Removing the server cover on page 85 Lay the server on its side for easier operation Locate the memory slots on the system board See System board components on page 42 Remove any parts or disconnect any cables that might prevent your access to the memory slots 0 2 W DY Open the retaining clips of the appropriate memory slot See Memory module installation rules on page 90 for the installation sequence information Figure 37 Opening the retaining clips of the memory slots 7 Touch the static protective package that contains the new memory module to any unpainted surface on the outside of the server Then take the new memory module out of the package Note Carefully handle the memory module by its edges Chapter 6 Installing removing or replacing hardware 91 8 Position the new memory module over the memory slot Make sure that the notch the new memory module is aligned with the key the memory slot Then press the new memory module straight down into the memory slot until the retaining clips close and the new memory module snaps into position Note If there is a gap between the memory module and the retaining clips the
184. moving a PCI card Installing or removing the Ethernet card Installing or removing the RAID card Installing or removing the ThinkServer 9240 8i RAID 5 Upgrade Key 5 Installing or removing the ThinkServer SATA Software RAID 5 Key Installing or removing the ThinkServer Remote Management Module Installing or removing the TPM module Installing or removing the DIT module Installing or replacing an optical drive Installing or CERE a renee hard disk drive Removing or installing a non hos swap Shard disk drive E le 66 67 67 69 70 70 71 72 73 74 74 79 80 80 81 83 83 83 84 84 85 85 87 89 89 93 96 98 100 102 105 109 111 115 119 123 Replacing the hot swap hard disk drive backplane Replacing the non lob swap power PPY assembly Replacing a hot swap supply module Replacing the power distribution Board arid cage assembly Replacing the front panel beard gscombl Replacing the front system fan Replacing the rear system fan Replacing the heat sink and fan Replacing the microprocessor Replacing the system board battery Replacing the system board Completing the parts replacement Reinstalling the server cover and reconnecting cables Updating the server configuration Chapter 7 diagnostics Troubleshooting procedure Viewing the status and diagnostic LEDs
185. n Removing a non hot swap hard disk drive Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to remove a non hot swap hard disk drive Before you begin consider the following hard disk drive installation rules Follow the order of the hard disk drive bays when installing a hard disk drive See Server components on page 25 to locate the hard disk drive bays in your server For RAID configuration the hard disk drives must be the same type with the same capacity if they are within a single RAID array For more information see Configuring RAID on page 71 For hard disk drives with different capacities install the hard disk drive with the lowest capacity first Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Depending on the model your server might look slightly different from the illustrations in this topic To remove a non hot swap hard disk drive do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 124 ThinkServer Hardware Maintenance Manual 2 Use the front door key to unlock the front door and then use the front
186. n option requires a graphics card installed Enable or disable the onboard LAN1 I O ROM Chapter 5 Configuring the server 59 Submenu item Selections Onboard LAN2 I O ROM Disabled Pe eee PCI ROM Priority Legacy ROM EFI Compatible ROM USB Configuration USB Controller Disabled set USB configuration Enabled parameters Legacy USB Support Enabled Disabled e Auto Port 60 64 Emulation Disabled Enabled TANDBERGRDX 3040 Auto Floppy Forced FDD Hard Disk e CD ROM Console Redirection Console Redirection Disabled Configuration set console e Serial Port 1 redirection configuration parameters Serial Port 2 Security menu Comments Enable or disable the onboard LAN2 I O ROM Choose a mode for the PCI ROM priority In case of multiple Option ROMs Legacy ROM and EFI Compatible ROM the selection specifies which PCI Option ROM to launch Enable or disable the USB controller Enable or disable the support on legacy USB devices Enable or disable the port 60h 64h emulation This function is for the operating system that does not support legacy USB devices Mass storage device emulation type Auto means to enumerate devices according to their media format Optical devices are emulated as CD ROM drives with no media are emulated according to the drive type The setting specifies how the host computer and the remote computer which the user is usin
187. n the IPMI 2 0 specification The SEL is accessible regardless of the system power state through the BMC in band and out of band interfaces For more information about viewing the SEL refer to the Remote Management Module User Guide on the documentation DVD that comes with your server Basic troubleshooting tables Use the basic troubleshooting information to find solutions to problems that have definite symptoms ThinkServer EasyStartup program problems Follow the suggested actions for the corresponding symptom in the order in which they are listed until the problem is solved If none of these actions solve the problem see Troubleshooting procedure on page 171 for the subsequent steps you should check after using the information in this topic If the problem cannot be solved by yourself seek technical assistance See Chapter 9 Getting information help and service on page 213 Note If you are instructed to remove install or replace any CRUs refer to the related procedure in Chapter 6 Installing removing or replacing hardware on page 83 172 ThinkServer Hardware Maintenance Manual ThinkServer EasyStartup DVD does not start 1 Make sure that the server supports the ThinkServer EasyStartup program and has a bootable DVD drive 2 Make sure that you have set the optical drive with the ThinkServer EasyStartup DVD as the first startup device 3 Verify if the optical drive or the disc has
188. nd custom installation services Service availability and service name might vary by country or region For more information about these services go to the Lenovo Web site at http www lenovo com Chapter 9 Getting information help and service 215 216 ThinkServer Hardware Maintenance Manual Appendix A Notices Lenovo may not offer the products services or features discussed in this document in all countries Consult your local Lenovo representative for information on the products and services currently available in your area Any reference to a Lenovo product program or service is not intended to state or imply that only that Lenovo product program or service may be used Any functionally equivalent product program or service that does not infringe any Lenovo intellectual property right may be used instead However it is the user s responsibility to evaluate and verify the operation of any other product program or service Lenovo may have patents or pending patent applications covering subject matter described in this document The furnishing of this document does not give you any license to these patents You can send license inquiries in writing to Lenovo United States Inc 1009 Think Place Building One Morrisville NC 27560 U S A Attention Lenovo Director of Licensing LENOVO PROVIDES THIS PUBLICATION 5 IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPL
189. nformation on page iii and Guidelines on page 83 This topic provides instructions on how to remove a PCI card Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Use any documentation that comes with the PCI card and follow those instructions in addition to the instructions in this topic To remove a PCI card do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 3 Lay the server on its side for easier operation Chapter 6 Installing removing or replacing hardware 95 4 Locate the PCI card you want to remove See System board components on page 42 5 f necessary remove any parts or disconnect any cables that might impede your access to the PCI card Depending on the type of the PCI card you might also need to disconnect any cables from the PCI card the system board and or the hot swap hard disk drive backplane 6 Remove the screw that secures the PCI card Then grasp the PCI card by its edges and carefully pull it out of the PCI card slot Note The PCI card fits tightly into the PCI card slot If necessary alternate moving each side of the PCI card a small and equal amount until it is com
190. ng Use the microprocessor socket cover removed from the new system board To install it on the old system board do the following a Make sure that the small handle and the microprocessor retainer are in the fully open position Chapter 6 Installing removing or replacing hardware 165 b Hold the microprocessor socket cover and align the notches Ell on the socket cover with the tabs in the microprocessor socket Then carefully lower the socket cover straight down into the socket Notes 1 Your microprocessor socket and cover might look slightly different from the illustration 2 The small triangle El on one corner of the microprocessor socket cover is the orientation indicator The microprocessor socket cover is in the correct orientation when this indicator faces toward the beveled corner EB of the microprocessor socket Figure 101 Installing the microprocessor socket cover c Make sure that the microprocessor socket cover is properly seated and then gently press it down until it is securely seated in the socket Figure 102 Seating the microprocessor socket cover in the socket 166 ThinkServer Hardware Maintenance Manual Close the microprocessor retainer Gently press down the small handle and then push the handle inward to lock the retainer into position and secure the microprocessor socket cover in the socket Figure 103 Securing the microprocessor socket cover 17 Note the orientation of the new system bo
191. ng RAID on page 71 e Configuring the Ethernet controllers on page 80 e Updating the firmware on page 80 Using the Setup Utility program This topic provides information about using the Setup Utility program The Setup Utility program is part of the server firmware You can use the Setup Utility program to view and change the configuration settings of your server regardless of which operating system you are using However the operating system settings might override any similar settings in the Setup Utility program Starting the Setup Utility program This topic provides instructions on how to start the Setup Utility program To start the Setup Utility program do the following 1 Connect the server to an ac power source and press the power switch on the front panel to turn on the server See Turning on the server on page 53 2 Press the F1 key as soon as you see the logo screen Then wait for several seconds and the Setup Utility program opens If you have set a password you need to type the correct password to enter the Setup Utility program For password information see Using passwords on page 65 Viewing information in the Setup Utility program The Setup Utility program menu lists various items about the system configuration Select a desired item to view information or change settings When working with the Setup Utility program you must use the keyboard The keys used to perform various tasks are disp
192. ng the server cover to the rear 86 ThinkServer Hardware Maintenance Manual 6 Pivot the server cover outward to completely remove it Figure 33 Removing the server cover Attention For proper cooling and airflow install the server cover before turning on the server Operating the server for more than 30 minutes with the server cover removed might damage server components To reinstall the server cover see Reinstalling the server cover and reconnecting cables on page 168 Removing and reinstalling the front bezel Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to remove and reinstall the front bezel Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Depending on the model your server might look slightly different from the illustrations in this topic To remove and reinstall the front bezel do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 Chapter 6 Installing removing or replacing hardware 87 3 Remove the front bezel b
193. ningsavfall men m bruke de tilgjengelige innsamlingssystemene for retur resirkulering og gjenvinning av kassert elektrisk og elektronisk utstyr for redusere en eventuell skadelig virkning av elektrisk og elektronisk utstyr p milj og helse som skyldes skadelige stoffer Du finner mer informasjon om WEEE p denne adressen http www lenovo com lenovo environment Appendix A Notices 223 Zna ka odpadn elektrick a elektronick za zen OEEZ Waste Electrical and Electronic Equipment WEEE se t k pouze zem Evropsk Unie EU Norska Za zen jsou ozna ena v souladu s evropskou sm rnic 2002 96 EC kter se t k likvidace star ch elektrick ch a elektronick ch za zen OEEZ Sm rnice ur uje pravidla pro vracen a recyklaci pou it ch za zen kter jsou platn v Evropsk Unii T mto t tkem se ozna uj r zn za zen Ozna uje e produkt nesm b t vyhozen do b n ho odpadu ale po skon en ivotnosti vr cen podle t to sm rnice U ivatel takov chto za zen ozna en ch zna kou OEEZ podle dodatku IV sm rnice OEEZ nesm na konci ivotnosti vyhodit za zen jako net d n odpad ale mus pou t dostupnou sb rnou s aby bylo za zen recyklov no a aby byly minimalizov ny mo n dopady za zen na prost ed a zdrav lid za zen m e obsahovat nebezpe n l tky Dal informace o zna ce OEEZ WEEE naleznete na webov str nce http
194. ns the new rear system fan to any unpainted surface on the outside of the server Then remove the new rear system fan from the package Chapter 6 Installing removing or replacing hardware 153 7 Position the new rear system which has four new rubber mounts attached on the chassis so that the four new rubber mounts are aligned with the corresponding holes in the chassis Push the rubber mounts through the holes and then pull on the tips of the rubber mounts from the other side of the chassis until the rear system fan is secured in place Figure 89 Installing the rear system fan 8 Connect the new rear system fan cable to the system fan 3 connector on the system board See System board components on page 42 9 If you are instructed to return the old rear system fan follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To complete the replacement go to Completing the parts replacement on page 168 Replacing the heat sink and fan assembly Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to replace the heat sink and fan assembly 154 ThinkServer Hardware Maintenance Manual CAU
195. nstalling removing or replacing hardware 147 8 Remove the screw El on the chassis that secures the front panel board assembly Then carefully remove the front panel board assembly from the chassis and pull the signal cables of the front panel board assembly out of the chassis Figure 84 Removing the front panel board assembly 9 Touch the static protective package that contains the new front panel board assembly to any unpainted surface on the outside of the server Then take the new front panel board assembly out of the package 10 Note the cable connection Then disconnect the signal cables from the rear of the old front panel board assembly and connect them to the rear of the new one 148 ThinkServer Hardware Maintenance Manual 11 Route the signal cables of the new front panel board assembly through the corresponding hole in the chassis and position the new front panel board assembly on the chassis so that the screw hole in it is aligned with the corresponding screw hole El in the chassis Then install the screw to secure the front panel board assembly in place Figure 85 Installing the front panel board assembly 12 Connect the front panel USB cable to the internal dual port USB 2 0 connector 1 on the system board Then connect the front panel cable to the front panel connector on the system board See System boar
196. nt Logs Enabled If this item is set to Enabled e Disabled the SEL will be cleared Configuration Source Static Select to configure LAN channel1 parameters statically or dynamically Do Nothing DHCP The Do Nothing option means that BMC network parameters will not be modified during the BIOS phase Dynamic Boot Options menu This topic provides information about the menus and items on the Boot Options menu in the Setup Utility program The Boot Options menu provides an interface to help you view or change the server startup options including the startup sequence and boot priority for various devices Changes in the startup options take effect when you start the server The startup sequence specifies the order in which the server checks devices to find a boot record The server starts from the first boot record that it finds For example you can define a startup sequence that checks for a disc in the optical drive then checks the hard disk drive and then checks a network device For information about setting the startup sequence or selecting a startup device see Selecting a startup device on page 66 The following list showing the order in which devices will be started up is always displayed Even devices that are not attached to or installed in your server are listed For each device that is attached to or installed in the server information about it is presented on the screen after the colon 1 UEFI D
197. ntains information about obtaining help and service Before you call Before you call do the following to try to solve the problem by yourself e Check all cables to make sure that they are connected Check the power switches to make sure that the system and optional devices are turned on Use the troubleshooting information in your system documentation on the documentation DVD that comes with your product Check for the updated information new device drivers and hints and tips on the Lenovo Support Web site at http support lenovo com If possible be at your product when you call Have the following information available e Machine type and model Serial numbers of your Lenovo hardware products Description of the problem e Exact wording of any error messages e Hardware and software configuration information Calling for service During the warranty period you can get help and information by telephone through the Customer Support Center The following services are available during the warranty period Problem determination Trained service personnel are available to assist you with determining a hardware problem and deciding what action is necessary to fix the problem e Hardware repair If the problem is caused by hardware under warranty trained service personnel are available to provide the applicable level of service 214 ThinkServer Hardware Maintenance Manual Engineering Change management Ther
198. o reciclagem e recupera o de REEE por forma a minimizar potenciais efeitos dos EEE sobre 222 ThinkServer Hardware Maintenance Manual o ambiente sa de publica resultantes da presen a de subst ncias perigosas Para obter informa es adicionais acerca da REEE consulte sitio da web http www lenovo com lenovo environment Het WEEE merkteken Waste Electrical and Electronic Equipment geldt alleen voor landen binnen de Europese Unie EU en Noorwegen Apparaten worden van een merkteken voorzien overeenkomstig Europese Richtlijn 2002 96 EC inzake afgedankte elektrische en elektronische apparatuur waste electrical and electronic equipment WEEE Deze richtlijn bepaalt het raamwerk voor het retourneren en recyclen van gebruikte apparatuur zoals van toepassing binnen de Europese Unie Dit merkteken wordt aangebracht op diverse producten om aan te geven dat het product in kwestie niet dient te worden weggegooid maar dat het aan het eind van de levenscyclus krachtens deze Richtlijn dient te worden geretourneerd Gebruikers van elektrische en elektronische apparaten EEE welke zijn voorzien van het WEEE merkteken zijn gehouden aan Annex IV van de WEEE Richtlijn en mogen gebruikte EEE niet weggooien als ongesorteerd afval maar dienen gebruik te maken van het inzamelproces voor het teruggeven recyclen en terugwinnen van WEEE dat voor hen beschikbaar is en dienen de mogelijke effecten die EEE ten gevolge van de aanwezigheid van schadelijke sto
199. o not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to install a non hot swap hard disk drive Before you begin consider the following hard disk drive installation rules Follow the order of the hard disk drive bays when installing a hard disk drive See Server components on page 25 to locate the hard disk drive bays in your server For RAID configuration the hard disk drives must be the same type with the same capacity if they are within a single RAID array For more information see Configuring RAID on page 71 128 ThinkServer Hardware Maintenance Manual For hard disk drives with different capacities install the hard disk drive with the lowest capacity first Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Notes Depending on the model your server might look slightly different from the illustrations in this topic Use any documentation that comes with the hard disk drive and follow those instructions in addition to the instructions in this topic To install a non hot swap hard disk drive do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to t
200. o pin 2 and pin 3 the server will be directly turned on when you press the power switch without waiting for the BMC ready The BMC function might not be available in this situation El BIOS recovery jumper Set the jumper and boot the server from a BIOS recovery image in order to recover your BIOS settings To recover the BIOS see Recovering from a BIOS update failure on page 68 Clear password jumper Used to erase forgotten passwords such as an administrator password and a user password To clear passwords do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 3 Lay the server on its side for easier operation 4 Locate the Clear password jumper on the system board and then move the jumper from the default normal position pin 1 and pin 2 to the short circuited position pin 2 and pin 3 5 Wait more than 10 seconds and then move the Clear password jumper back to the normal position pin 1 and pin 2 6 Reinstall the server cover and connect the power cord s See Completing the parts replacement on page 168 7 Wait about 30 seconds Then turn on the server The BIOS passwords are erased including the administrator password and user password 8 To set new passwords see Using pass
201. o the following to install the device driver for the Ethernet card 1 Save any open documents and exit all applications Click Start Rright click My Computer and select Properties The System Properties window opens Click the Device Manager button on the Hardware tab The Device Manager window opens Expand the Network adapters Right click one of the Ethernet cards PRO 1000PT or the yellow question mark Select Update Driver The Hardware Update Wizard window opens You will be asked if you permit Windows to connect to Windows Update to search for software 0 2 W N Make a selection depending on your needs and click Next 8 Insert the ThinkServer EasyStartup DVD that comes with your server into the optical drive Note You do not need to use the driver disc that comes with the Ethernet card 9 Select Install the software automatically Recommended and click Next to continue 10 Follow the instructions on the screen to complete the installation Removing the Ethernet card Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 Chapter 6 Installing removing or replacing hardware 97 This topic provides instructions on how to remove the Ethernet card Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Use any d
202. o the remote console Meanwhile it is easily accessible by remote KVM and controllable through LAN or Internet For detailed information refer to the Remote Management Module User Guide on the documentation DVD that comes with your server Media redirection The embedded Web server provides a Java JNLP to enable the remote media redirection This is used in conjunction with the remote KVM feature or as a standalone applet The media redirection feature is intended to enable system administrators or users to mount a remote optical drive floppy drive or USB flash disk as a USB device to the server Once mounted the remote device functions as a local device to the server enabling system administrators or users to boot the server and install software including operating systems copy files update the BIOS from this device Web Services for Management WS MAN The BMC firmware supports the WS MAN specification Local Directory Authentication Protocol LDAP The BMC firmware supports the LDAP for user authentication Note The IPMI users passwords and sessions are not supported over LDAP Chapter 3 Product overview 11 Embedded Web server The BMC provides an embedded Web server for out of band management The user authentication is handled by IPMI user names and passwords For more information refer to the Remote Management Module User Guide on the documentation DVD that comes with your server Specifications This topic
203. o to http www lenovo com lenovo environment Requirement for batteries containing perchlorate The following statement applies to users in the state of California U S A California Perchlorate Information Products containing CR manganese dioxide lithium coin cell batteries may contain perchlorate Perchlorate Material special handling may apply See http www dtsc ca gov hazardouswaste perchlorate The foregoing notice is provided in accordance with California Code of Regulations Title 22 Division 4 5 Chapter 33 Best Management Practices for Perchlorate Materials This product part may include a lithium manganese dioxide battery which contains a perchlorate substance Particulate contamination Attention Airborne particulates including metal flakes or particles and reactive gases acting alone or in combination with other environmental factors such as humidity or temperature might pose a risk to the server that is described in this document Risks that are posed by the presence of excessive particulate levels or concentrations of harmful gases include damage that might cause the server to malfunction or cease functioning altogether This specification sets forth limits for particulates and gases that are intended to avoid such damage The limits must not be viewed or used as definitive limits because numerous other factors such as temperature or moisture content of the air can influence the impact of particulates or environmenta
204. ocumentation that comes with the Ethernet card and follow those instructions in addition to the instructions in this topic To remove the Ethernet card do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 3 Lay the server on its side for easier operation 4 Locate the Ethernet card The Ethernet card can be in the PCI E slot 2 or the PCI E slot 3 that supports card with 167 mm 6 57 inches in length See System board components on page 42 5 The Ethernet card is a kind of PCI card See Removing a PCI card on page 95 and follow those instructions to remove the Ethernet card 6 If you are instructed to return the old Ethernet card follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To complete the removal procedure go to Completing the parts replacement on page 168 Installing or removing the RAID card This topic provides instructions on how to install or remove the RAID card A specific RAID card is required for server models with more than four hard disk drives or models that use SAS hard disk drives You can also install the RAID ca
205. odels Lenovo RDX USB drive bundle cables MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 67Y1425 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Adapters and miscellaneous FRUs The following table lists information about adapters and miscellaneous FRUs FRU number emu Pro 1000 PT dual port Ethernet card MT 0387 CTO MT 0388 CTO MT 0389 CTO 67Y1430 1 MT 0390 CTO MT 0391 CTO MT 0392 CTO MT 0393 CTO 194 ThinkServer Hardware Maintenance Manual 09 PFR mumber CRU MT 0441 pu ThinkServer 9240 8i RAID 0 1 Adapter eight ports without RAID 5 Upgrade Key B2 MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3634 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO ThinkServer 9240 8i RAID 5 Upgrade Key MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3604 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Remote Management Module V1 0 MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3666 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Onboard SATA Software RAID 5 Key MT 0387 CTO MT 0388 CTO MT 0389 CTO MT 0390 CTO 03X3667 MT 0391 CTO MT 0392 CTO MT 0393 CTO MT 0441 CTO Chapter 8 FRU lists 195 TPM Module V1 1 MT 0387 CTO 11U 11G 12U 12G MT 0388 CTO 11U 12U 12G 13U 13G 14U MT 0389 CTO 11U MT 0390 CTO 11U 11G 12U 12G 13U 13G 03X3709 MT 0391 CTO 11U MT 0392 CTO 11U 12U 13U 14U 15U MT 0393 CTO 11U 11G 12U 12G MT 0441 CT
206. odels MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models KT2A chassis base assembly MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3714 2 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models KT2A 9225 38 fan holder MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3717 2 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models 450 mm 17 72 inches single to mini SAS cable 4 1 with one SGPIO port mini SAS signal cable with four SATA ports and one SGPIO port MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3705 1 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models Chapter 8 FRU lists 193 700 mm 27 56 inches mini SAS to mini SAS signal cable MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3706 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all models 15u 750 mm 29 53 inches single SATA cable V1 0 MT 0387 CTO all models MT 0388 CTO all models MT 0389 CTO all models MT 0390 CTO all models 03X3696 MT 0391 CTO all models MT 0392 CTO all models MT 0393 CTO all models MT 0441 CTO all m
207. odels that have hot swap hard disk drive s installed See Features on page 7 for more information about the supported hot swap hard disk drives For a list of the ThinkServer hard disk drive options go to http www lenovo com thinkserver Click the Products tab and then click Options gt ThinkServer Hard Drives to view the information You can install or replace a hot swap hard disk drive without turning off the server which helps you avoid significant interruption to the operation of the system The EMI integrity and cooling of the server are protected by having all drive bays covered or occupied The number of the installed hard disk drives in your server varies depending on the server model The vacant bays are either covered by an EMI protective panel or occupied by dummy hard disk drive trays When you install a hot swap hard disk drive save the removed dummy hard disk drive tray from the drive bay in the event that you later remove the hot swap hard disk drive and need the dummy tray to cover the place Attention An unoccupied drive bay without any other protection might impact the EMI integrity and cooling of the server which might result in overheating or component damage To maintain the EMI integrity and cooling of the server install a new hot swap hard disk drive as soon as you remove the failing one or the dummy tray Before you begin consider the following hard disk drive installation rules e Follow the order of the hard
208. ogram The PC Doctor for DOS diagnostic program runs independently of the operating system Use this diagnostic program to test and gather information about your system in order to ensure your system is working correctly and resolve any hardware issues You can run the diagnostic program from a diagnostic disc that you created To use the diagnostic program do the following Note Lenovo maintains the Support Web site by making changes and improvements periodically The actual procedure might vary slightly from what is described in this topic 1 Go to the Lenovo Support Web site at http support lenovo com 2 Click Download Drivers amp Software and follow the instructions on the Web page to locate the diagnostic program 3 Download the ISO image for the diagnostic program and the readme file in TXT 4 Use any disc burning software to create a bootable disc with the ISO image 5 Print the readme file that contains the instructions on how to use the diagnostic program and follow the instructions to start the program from the disc Then follow the instructions on the screen to start the diagnostic test 6 Remove the diagnostic disc from the optical drive when you complete the diagnostic process Viewing the system event log The system event log SEL contains information about all the POST and system management interrupt SMI events You can view the SEL to diagnose system problems The BMC implements the SEL as specified i
209. ollowing illustration shows the 3 5 inch hard disk drive cage For the 2 5 inch hard disk drive cage the installation procedure is the same 1 Figure 76 Installing the hard disk drive cage 13 Reinstall all the hot swap hard disk drives and dummy trays if any in the hard disk drive cage See Installing or replacing a hot swap hard disk drive on page 119 14 Refer to your note and reconnect the cables to the backplane 15 Reinstall the front system fan See Replacing the front system fan on page 149 16 Reinstall the front bezel See Removing and reinstalling the front bezel on page 87 196 ThinkServer Hardware Maintenance Manual 17 If you are instructed to return the old hot swap hard disk drive backplane follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To complete the replacement go to Completing the parts replacement on page 168 Replacing the non hot swap power supply assembly Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to replace the non hot swap power supply assembly This topic applies only to server models that come with a non hot swap power supply assembly
210. ompliant and universal input Fans You server comes with the following fans to provide proper system cooling and airflow One heat sink and fan assembly One or two front system fans depending on the model One rear system fan 8 ThinkServer Hardware Maintenance Manual Internal drives Internal drives are devices that your server uses to read and store data The internal drives supported by your server vary by model Hard disk drive Five to eight 3 5 inch hot swap Serial Advanced Technology Attachment SATA or Serial Attached SCSI SAS hard disk drives SCSI is the acronym for Small Computer System Interface Up to eight 2 5 inch hot swap SAS hard disk drives Up to four 3 5 inch hot swap SATA or SAS hard disk drives Up to four 3 5 inch non hot swap SATA hard disk drives Note For server models with more than four hard disk drives or models that use SAS hard disk drives there must be a required RAID card installed See RAID card on page 33 e Optical drive Up to two 5 25 inch SATA optical drives DVD ROM or DVD Burner CD RW Rambo 8 The lower optical drive bay is installed with a 5 25 inch SATA optical drive DVD ROM or DVD Burner CD RW Rambo 8 The upper optical drive bay is for a Removable Disk Technology RDX Universal Serial Bus USB drive bundle For the location information about the internal drives or drive bays see Server components on page 25 For information about the RDX USB d
211. on for Taiwan agg n ic Appendix A Notices 219 Battery recycling information for the European Union EU Notice This mark applies only to countries within the European Union EU Batteries or packaging for batteries are labeled in accordance with European Directive 2006 66 EC concerning batteries and accumulators and waste batteries and accumulators The Directive determines the framework for the return and recycling of used batteries and accumulators as applicable throughout the European Union This label is applied to various batteries to indicate that the battery is not to be thrown away but rather reclaimed upon end of life per this Directive In accordance with the European Directive 2006 66 EC batteries and accumulators are labeled to indicate that they are to be collected separately and recycled at end of life The label on the battery may also include a chemical symbol for the metal concerned in the battery Pb for lead Hg for mercury and Cd for cadmium Users of batteries and accumulators must not dispose of batteries and accumulators as unsorted municipal waste but use the collection framework available to customers for the return recycling and treatment of batteries and accumulators Customer participation is important to minimize any potential effects of batteries and accumulators on the environment and human health due to the potential presence of hazardous substances For proper collection and treatment g
212. on one drive and comparing the results to the contents of the parity drive You should run a consistency check on fault tolerant virtual drives periodically It is recommended that you run a consistency check at least once a month You must run a consistency check if you suspect that the 78 ThinkServer Hardware Maintenance Manual virtual drive data might be corrupted Be sure to back up the data before running a consistency check if you suspect the data might be corrupted To run a consistency check using the LSI Software RAID Configuration Utility program do the following 1 Start the LSI Software RAID Configuration Utility program See Starting the LSI Software RAID Configuration Utility program on page 74 2 On the main interface of the program select Check Consistency and follow the instructions on the Screen The consistency check rate is the rate at which consistency check operations are run on a system The consistency check rate be configured between 0 percent and 100 percent At percent the consistency check is done only if the system is not doing anything else At 100 percent the consistency check has a higher priority than any other system activity To configure the consistency check rate using the LSI Software RAID Configuration Utility program do the following Note Using a consistency check rate of 0 or 100 percent is not recommended The default value is 30 percent 1 Start the LSI Software RAID Conf
213. on page 38 9 If you are instructed to return the old RAID card follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To complete the removal procedure go to Completing the parts replacement on page 168 Then you need to reconfigure RAID for your server See Configuring RAID on page 71 Installing or removing the ThinkServer 9240 8i RAID 5 Upgrade Key This topic provides instructions on how to install or remove the ThinkServer 9240 8i RAID 5 Upgrade Key hereinafter referred to as the RAID 5 key The RAID 5 key expands the capability of the installed RAID card ThinkServer 9240 8i RAID 0 1 Adapter by activating RAID 5 and 50 levels for advanced SATA SAS hardware RAID You can purchase a RAID 5 key directly from Lenovo Installing the RAID 5 key on the RAID card Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to install the RAID 5 key on the RAID card Note This topic applies only to models that have a RAID card installed Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Use any documentation that comes with the RAID 5 key and follow those instruc
214. opic To replace a hot swap redundant power supply module do the following Chapter 6 Installing removing or replacing hardware 141 1 Locate the failing hot swap redundant power supply module on the rear of your server Then press the release tab in the direction as shown and carefully pull the handle the same time to slide the redundant power supply module out of the chassis Note Do not use too much strength You can first carefully slide the redundant power supply module a little bit out to release it from the secured position Then completely slide it out of the chassis Figure 80 Removing a hot swap redundant power supply module 2 Touch the static protective package that contains the new hot swap redundant power supply module to any unpainted surface on the outside of the server Then remove the new hot swap redundant power supply module from the package 142 ThinkServer Hardware Maintenance Manual 3 Note the orientation of the hot swap redundant power supply module and then slide the new hot swap redundant power supply module into the chassis until it snaps into position Note If your server comes with one hot swap redundant power supply module installed in the redundant power supply module bay 1 the bay number is marked on the rear of the chassis and you are installing a secondary hot swap redundant power supply module to provide redundant power you need to remove the shield that prote
215. ostic 51 power status 17 System board 50 system board hardware fault 50 System status 18 locations 13 LSI Software RAID Configuration Utility program interface 75 starting 74 machine type and model label locations 13 Main menu Setup Utility program 56 MegaRAID Storage Manager program installing and using 79 memory features 8 memory module installation rules 90 installing 91 removing 92 memory module installation guidelines 90 microprocessor features 8 replacing 157 NIC status LED 18 non hot swap hard disk drive installing 128 removing 124 non hot swap power supply assembly replacing 137 onboard SATA software RAID configuring 74 optical drive installing 115 replacing 115 optical drive status LED 16 option completing the replacement 168 P particulate contamination 220 parts replacement completing 168 password considerations 65 setting changing deleting 65 Setup Utility program 65 PC Doctor for DOS software 13 troubleshooting and diagnostics 172 PCI card installing 93 removing 95 physical drive rebuilding 78 POST code diagnostic LED 51 power distribution board and cage assembly replacing 143 power status LED 17 power supply features 8 precautions guidelines 83 R RAID configuring 71 for your server 73 introduction 72 RAID 5 key on the RAID card installing 100 removing 101 Copyright Lenovo 2011 RAID array creating adding or deleting 76 RAID card in
216. osure Some laser products contain an embedded Class or Class laser diode Note the following Laser radiation when open Do not stare into the beam do not view directly with optical instruments and avoid direct exposure to the beam Before you begin consider the following optical drive installation rules The server has two optical drive bays If the server has only one optical drive installed make sure that the optical drive is installed in the lower bay optical drive bay 1 The upper bay is for a secondary optical drive or a RDX USB drive bundle server option The following table provides information about the recommended power connector and connector the system board for the installed optical drive or RDX USB drive bundle See Server components on page 25 for the locations of the optical drive bays and System board components on page 42 for the locations of the connectors on the system board Optical drive bay 1 lower An optical drive installed SATA 5 connector bay Optical drive bay 2 upper An optical drive installed in P12 SATA 4 connector bay some models A RDX USB drive bundle Internal dual port USB 2 0 server option connector 2 Chapter 6 Installing removing or replacing hardware 115 Note For information about the RDX USB drive bundle and instructions on how to install it refer to the documentation that comes with the RDX USB drive bundle You can purchase this
217. oting and diagnostic methods to help you solve problems that might occur in the server If you cannot diagnose and correct a problem by using the information in this chapter see Chapter 9 Getting information help and service on page 213 for additional troubleshooting resources Troubleshooting procedure Use the following information as a general procedure for diagnosing and troubleshooting problems you experience with your server 1 Verify that the power cords and the cables for all attached devices are connected correctly and securely 2 Verify that the server and all attached devices that require ac power are connected to properly grounded functioning electrical outlets 3 Verify that all installed hardware and attached devices are enabled in the BIOS settings of your server For more information about accessing and changing the BIOS settings see Using the Setup Utility program on page 55 4 View the status and diagnostic LEDs to identify the system and device status and diagnose problems See Viewing the status and diagnostic LEDs on page 171 5 f the server is not working after you have added new software installed a new optional device or replaced a piece of hardware remove or reinstall the software or device to see if the problem could be solved 6 View the SEL to diagnose problems See Viewing the system event log on page 172 7 Turn on the server and press Esc as soon as you see the logo screen to view any
218. ou can view the PDF version on another computer for reference Chapter 6 Installing removing or replacing hardware 107 Notes 1 Use any documentation that comes with the iKVM key and follow those instructions in addition to the instructions in this topic 2 If you remove the iKVM key the iKVM function for server remote management is unavailable To remove the iKVM key do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 3 Lay the server on its side for easier operation 4 Locate the iKVM key on the system board and then lift the iKVM key straight up to remove it from the iKVM key connector e 5 f you are instructed to return the old iKVM key follow all packaging instructions and use any packaging materials that are supplie
219. our screws on the new heat sink and fan assembly are aligned with the corresponding mounting studs on the system board Note the orientation of the new heat sink and fan assembly and make sure that you properly place it so that you can easily connect the heat sink and fan assembly cable to the microprocessor fan connector on the system board See System board components on page 42 156 ThinkServer Hardware Maintenance Manual 10 Install the four screws to secure the new heat sink and fan assembly on the system board It is recommended that you carefully install the four screws using the following method to avoid any possible damage to the system board a Partially tighten screw El then firmly tighten screw ER and then return to screw firmly tighten it Do not over tighten the screws b Partially tighten screw EM then firmly tighten screw El and then return to screw firmly tighten it Do not over tighten the screws Figure 91 Installing the screws to secure the heat sink and fan assembly 11 Connect the heat sink and fan assembly cable
220. ower supply modules Power cord connector s Used to connect the power cord s Serial port Used to attach a device that uses a 9 pin serial port El VGA DB 15 connector Used to attach a video device such as a VGA monitor or other devices that use a VGA DB 15 connector USB connectors Used to attach a device that requires a USB connector such as a USB keyboard a USB mouse a USB scanner or a USB printer If you have more than six USB devices you can purchase a USB hub which you can use to connect additional USB devices Expansion card area You server has four expansion slots on the system board for you to install appropriate PCI cards For detailed information see System board components on page 42 Chapter 3 Product overview 21 Dn Ethernet connectors Used to attach an Ethernet cable for a LAN Each Ethernet connector has two status LEDs to help you identify the Ethernet connectivity activity and connection speed Note The Ethernet connector 2 callout Eg marked with MGMT is for system management If you want to use remote management functions you need to connect an Ethernet cable to the Ethernet connector 2 e c Left Gee On The server is connected to a LAN LOC ERE The server is disconnected from a LAN T NEM megabits per second Gee fon connection speedis 100 Mbps Front door key Used to open or lock the front door
221. parts in a safe place f you must turn on the server while the server cover is removed make sure that no one is near the server and that no tools or other objects have been left inside the server Do not attempt to lift an object that you think is too heavy for you If you have to lift a heavy object observe the following precautions Make sure that you can stand safely without slipping Distribute the weight of the object equally between your feet Use a slow lifting force Never move suddenly or twist when you lift a heavy object To avoid straining the muscles in your back lift by standing or by pushing up with your leg muscles Copyright Lenovo 2011 83 Make sure that you have an adequate number of properly grounded electrical outlets for the server monitor and other devices Back up all important data before you make changes to drives Have a small flat blade screwdriver available e You do not have to turn off the server to install or replace a hot swap redundant power supply module hot swap hard disk drives or hot plug USB devices However you must turn off the server before performing any steps that involve installing removing or replacing adapter cables or non hot swap devices or components To view the LEDs on the system board and internal components leave the server connected to power e When you are finished working on the server reinstall all safety shields guards labels and groun
222. performs a series of tests that checks the operation of the system and options This series of tests is called the power on self test POST To assist in troubleshooting a system hang during the POST process the POST code diagnostic LEDs on the system board can be used to identify the last POST process executed Note The POST code diagnostic LEDs and POST error code information are intended only for trained service personnel of Lenovo Refer to System board LEDs on page 50 for detailed information about the POST code diagnostic LEDs and POST error codes Chapter 7 Troubleshooting and diagnostics 177 178 ThinkServer Hardware Maintenance Manual Chapter 8 FRU lists This chapter lists information about the FRUs Attention Be sure to read and understand the Safety information on page iii before replacing any FRUs In the following tables a CRU is identified as 1 2 or N in the CRU column means that the part is not a CRU 1 means that the part is a Self service CRU and 2 means that the part is an Optional service CRU Note The server configuration varies by model The following illustration shows only one type of server configuration server models with up to four 3 5 inch hot swap hard disk drives to provide a general view of the component locations For more information about the major server configurations see Server components on page 25 EHI E
223. place the optical drive Hard disk drive problems Follow the suggested actions for the corresponding symptom in the order in which they are listed until the problem is solved If none of these actions solve the problem see Troubleshooting procedure on page 171 for the subsequent steps you should check after using the information in this topic If the problem cannot be solved by yourself seek technical assistance See Chapter 9 Getting information help and service on page 213 Notes 1 If you are instructed to remove install or replace any CRUS refer to the related procedure in Chapter 6 Installing removing or replacing hardware on page 83 2 If the server model comes with hot swap hard disk drives the status LEDs on each hot swap hard disk drive help you easily identify a problem See Hot swap hard disk drive status LEDs on page 32 newly installed non hot swap hard disk drive is not 1 Make sure that recognized The signal cable and connector are not damaged The non hot swap hard disk drive is securely connected to the correct SATA connector on the system board and the SATA connector is enabled in the Setup Utility program See Using the Setup Utility program on page 55 All cables and jumpers if any are installed correctly 2 Run any diagnostic programs to test the hard disk drive 3 Reinstall the non hot swap hard disk drive and reconnect cables 4 Replace the signal cab
224. pletely removed from the slot Figure 42 Removing a PCI card 7 Install a new PCI card to replace the old one or install a PCI card slot bracket to cover the place See Installing a PCI card on page 93 8 If you are instructed to return the old PCI card follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To complete the removal procedure go to Completing the parts replacement on page 168 Installing or removing the Ethernet card This topic provides instructions on how to install or remove the Ethernet card Installing the Ethernet card Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to install the Ethernet card and how to install the Ethernet card driver on Windows operating systems 96 ThinkServer Hardware Maintenance Manual Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Use any documentation that comes with the Ethernet card and follow those instructions in addition to the instructions in this topic To install the Ethernet card do the following 1 Remove all media from the drives and turn off all attached devices and t
225. ppropriate power cable the signal cable to the rear of the new optical drive Figure 57 Connecting cables to the rear of the optical drive 8 If necessary connect the other end of the signal cable to the appropriate SATA connector on the system board See System board components on page 42 9 Reinstall the front bezel if you have removed it See Removing and reinstalling the front bezel on page 87 10 Do one of the following 118 ThinkServer Hardware Maintenance Manual e f you are installing an optical drive save the removed EMI protective shield from the chassis and plastic shield from the front bezel in the event that you later remove the drive and need the shields to cover the drive bay f you are replacing an optical drive and are instructed to return the old optical drive follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To complete the installation or replacement go to Completing the parts replacement page 168 Installing or replacing a hot swap hard disk drive Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to install or replace a hot swap hard disk drive This topic applies only to server m
226. process is completed Check and reconfigure the BIOS settings for your specific needs based on your note or refer to Using the Setup Utility program on page 55 Recovering from a BIOS update failure If the power to your server is interrupted while the BIOS is being updated your server might not restart correctly If this happens perform the following procedure to recover from the BIOS update failure To recover from a BIOS update failure do the following 1 Download a BIOS update utility program and its installation instructions from the Lenovo Support Web site Then make a bootable disc or a bootable USB key and print the TXT file that contains the installation instructions See Downloading the BIOS update utility program on page 67 68 ThinkServer Hardware Maintenance Manual 2 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server Remove the server cover See Removing the server cover on page 85 Locate the BIOS recovery jumper on the system board See System board jumpers on page 46 Remove any parts or disconnect any cables that might impede your access to the BIOS recovery jumper OOA Move the BIOS recovery jumper from the normal position pin 1 and pin 2 to the recovery position pin 2 and pin 3 7 Reinstall any parts or reconnect any cables and reinstall t
227. r to the port 1 on the RAID card Then connect the mini SAS connector J to the mini SAS signal cable connector 2 on the 2 5 inch hot swap hard disk drive backplane 3 Use the 2 pin 200 mm 7 87 inches RAID card to system board hard disk drive LED cable Connect the end J to the external connector on the RAID card and the end the hard disk drive LED connector on the system board Figure 24 Connecting cables for server models with one 2 5 inch hot swap hard disk drive backplane and a RAID card For connector location information about the RAID card hot swap hard disk drive backplane and the system board refer to the related topics in Locations on page 13 For information about connecting the appropriate power connector of the power supply to the backplane see Hot swap hard disk drive backplane on page 34 Server models with up to four 3 5 inch hot swap hard disk drives and one backplane For server models with up to four 3 5 inch SATA hot swap hard disk drives and one backplane you can either connect the SATA hard disk drive s to the SATA connectors on the system board or a required RAID card if you have one installed in the server For server models with up to four 3 5 inch SAS hot swap hard disk drives and one backplane connect the SAS hard disk drive s to the required RAID card installed in the server Note SATA is the only type of SATA supported by the RAID card Use the following instructions to connect th
228. r Switch on the front panel to turn on the server See Front panel on page 17 The server needs about 30 seconds for the BMC to initialize whenever you connect the server to an ac power source If you press the power switch on the front panel during this period the server will not start immediately it will start after the BMC initialization finishes e When the Wake on LAN feature is enabled on the server that is connected to an ac power source and a LAN a network administrator can remotely turn on or wake up the server from a management console using remote network management software You can also use the related BMC feature to remotely turn on the server through the management LAN Turning off the server CAUTION The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device The device also might have more than one power cord To remove all electrical current from the device ensure that all power cords are disconnected from the power source 2 7 felt The server can be turned off in one of the following ways e Turn off the server from the operating system if your operating system supports this feature After an orderly shutdown of the operating system the server will turn off automatically For instructions on how to shut down your specific operating system refer to the related documentation or help system for the operating s
229. r Hardware Maintenance Manual 8 Remove the four screws El at the rear of the chassis and the two screws Ell on the metal clip at the front of the power distribution board and cage assembly Then push the power distribution board and cage assembly from the rear until it is released from the metal retaining tab Ell and then carefully lift it out of the chassis ZA gt VAS S 252 xX SN S 5 Figure 82 Removing the power distribution board and cage assembly 9 Touch the static protective package that contains the new power distribution board and cage assembly to any unpainted surface on the outside of the server Then remove the new power distribution board and cage assembly from the package Chapter 6 Installing removing or replacing hardware 145 10 Install the new power distribution board and cage assembly into the chassis so that the four screw holes 11 12 13 14 in the rear of the new power distribution board and cage assembly are aligned with the corresponding holes marked with R in the rear of the chassis Meanwhile make sure that the two screw holes qin the metal clip at the front of the new power distribution board and cage assembly are aligned with the corresponding holes in the chassis Then install the four screws J and the two screws to secure the new power
230. rage Devices e Maintaining and Managing Storage Configurations The MegaRAID SAS Software User Guide is also available on the Lenovo Web site at http www lenovo com ThinkServerUserGuides Configuring the advanced SATA or SAS hardware RAID Some server models come with a required RAID card to provide advanced SATA SAS hardware RAID functions to the server You can also purchase the RAID card from Lenovo and install it into server models Chapter 5 Configuring the server 79 that support the RAID card to get advanced SATA SAS hardware RAID functions See RAID card on page 33 and Installing or removing the RAID card on page 98 for more information Note For server models with more than four hard disk drives or models that use SAS hard disk drives there must be a RAID card installed The RAID card provides the WebBIOS Configuration Utility program to help you configure RAID independently of the operating system You can also install the MegaRAID Storage Manager program and the MegaCLI Configuration Utility program to help you manage the RAID array and RAID controller in an operating system environment The supported RAID levels are RAID 0 1 and 10 To activate RAID 5 and 50 levels you need to install a RAID 5 key on the RAID card See Installing or removing the ThinkServer 9240 8i RAID 5 Upgrade Key on page 100 The installation packages for the MegaRAID Storage Manager program and the Configuration Utility prog
231. ram The BIOS Setup Utility program helps you view the server information and configure the server in the pre operating system environment See Using the Setup Utility program on page 55 BMC and Intelligent Plattorm Management Interface IPMI 2 0 The system board platform management subsystem is based on the integrated BMC features The BMC is a management chip that is integrated on the system board of your server With the BMC chip no matter what condition the server operating system is in and no matter if the server is on or off as long as the server is connected to network and an ac power source the interaction with the BMC controlled servers can be achieved through system network The user can obtain the server hardware health information and system event log SEL and is able to conduct the operations including turning on or off the server restarting the server locking the power switch on the front panel and so on This part of the server management is independent of the operating system and is called out of band management The system board platform management subsystem consists of the integrated BMC communication buses sensors Basic Input Output System BIOS and server management firmware It is responsible for error management and reporting system power control thermal monitoring system fan control and other management features The BMC provides system management and monitoring features based on the IPMI 2 0 specification IP
232. ram are on the ThinkServer EasyStartup DVD After you enter the operating system insert the ThinkServer EasyStartup DVD into the optical drive The installation packages for the programs are located in the Utilities and Others folder in the root directory of the DVD Note The ThinkServer EasyStartup DVD is designed for different types of servers and the Utilities and Others folder might contain additional installation packages that are not required to be installed into your server For instructions on how to configure and manage the advanced SATA or SAS hardware RAID refer to the MegaRAID SAS Software User Guide on the documentation DVD that comes with your server This document is also available on the Lenovo Web site at http www lenovo com ThinkServerUserGuides Configuring the Ethernet controllers The Ethernet controllers are integrated on the system board They provide an interface for connecting to a 10 Mbps 100 Mbps or 1000 Mbps network and provide full duplex FDX capability which enables simultaneous transmission and reception of data on the network You do not have to set any jumpers or configure the Ethernet controllers However you must install a device driver to enable the operating system to address the controllers The ThinkServer EasyStartup program simplifies the process of configuring RAID and installing supported operating systems and device drivers on your server See Using the ThinkServer EasyStartup program on pag
233. ram from http support lenovo com and create a self starting DOS based diagnostic utility that you can use to detect failing hardware components independently of the operating system For more information see Using the diagnostic program on page 172 Locations This topic provides information to help you locate your server components Machine type model and serial number label This topic helps you locate the two labels that contain the machine type model and serial number information for your server The two labels are the same One is on the front bezel and the other is on the chassis The machine type model and serial number identify your server When you contact Lenovo for help the information helps support technicians to identify your server and provide faster service Chapter 3 Product overview 13 The following illustration is a sample of the machine type model and serial number labels on the server Note Depending on the model type your server might look slightly different from the illustration in this topic MT M XXXX XXX S N XXXXXXX A Figure 2 Machine type model and serial number labels 14 ThinkServer Hardware Maintenance Manual Front view of the server This topic provides information to help you locate the parts on the front of the server The following illustration shows the front view of the server Figure 3 Front view of the serv
234. ray fails When drive in a RAID drive group fails you can rebuild the drive by recreating the data that was stored on the drive before it fails If the drive is not operational it must be replaced and the data on the failing drive must be rebuilt on a new drive to restore the system to fault tolerance If hot spare drives are available the failing drive might be rebuilt automatically without any user intervention The RAID controller recreates the data using the data stored on other drives in the drive group Rebuilding can be done only in drive groups with data redundancy such as RAID 1 5 and 10 drive groups For a detailed introduction to disk rebuild refer to Introduction to RAID in the MegaRAID SAS Software User Guide on the documentation DVD that comes with your server To rebuild a physical drive using the LSI Software RAID Configuration Utility program when a physical drive in an array fails do the following 1 Start the LSI Software RAID Configuration Utility program See Starting the LSI Software RAID Configuration Utility program on page 74 2 On the main interface of the program select Rebuild and follow the instructions on the screen Note Running a consistency check immediately after the rebuild completes to ensure data integrity for the virtual drives See Running a consistency check on page 78 The rebuild rate is the percentage of the computing cycles dedicated to rebuilding failing drives A rebuild rate of
235. rd for advanced SATA SAS hardware RAID functions For more information see RAID card on page 33 and Configuring RAID on page 71 Note This topic applies only to models that support the RAID card Installing the RAID card Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to install the RAID card Attention Make sure that you back up your data before installing the RAID card because you might need to reconfigure RAID and reinstall the operating system after installing the RAID card Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Use any documentation that comes with the RAID card and follow those instructions in addition to the instructions in this topic To install the RAID card do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 98 ThinkServer Hardware Maintenance Manual Remove the server cover See Removing the server cover on page 85 Lay the server on its side for easier operation Locate the PCI E slot 3 on the system board See System board components on page 42 Remove any parts or disconnect any ca
236. reberete in razumete varnostna navodila na DVD ju z dokumentacijo ki ste ga prejeli skupaj z izdelkom Antes de utilizar el producto aseg rese de leer y comprender las instrucciones de seguridad multiling es del DVD de documentaci n que se proporciona con el producto Var noga med att l sa s kerhetsinstruktionerna p dokumentations DVD skivan som f ljer med produkten innan du b rjar anv nda produkten fs FAS E ih FV DU BE E RU CE DVD er MAKE R Bu r n kullanmadan nce r nle birlikte g nderilen belge DVD si zerindeki ok dil i eren g venlik y nergelerini okuyup anlad n zdan emin olun 3 3 DVD nucky Important The caution and danger statements in this document labeled with numbers Each number identifies an English language caution or danger statement that refers to translated versions of the caution or danger statement in the Safety Information document For example if a danger statement is labeled Statement 1 translations for this danger statement are in the Safety Information document under Statement 1 Ensure that you read and un
237. ring RAID advanced SATA or SAS hardware RAID 79 onboard SATA software RAID 74 using the ThinkServer EasyStartup program 74 configuring the server 55 connecting cables 38 considerations password 65 consistency check running 78 contamination particulate and gaseous 220 creating adding or deleting RAID array 76 CRU completing the replacement 168 D devices handling static sensitive 84 DIMM installation rules 90 installing 91 Copyright Lenovo 2011 removing 92 DIT module installing 112 locations 18 removing 113 DIT panel LED 18 locations 18 documentation using 213 downloading the BIOS update utility program 67 E EasyUpdate Firmware Updater program using 81 error LED 19 Ethernet card installing 96 removing 97 Ethernet connectivity features 9 Ethernet controllers configuring 80 Ethernet status LED 22 Exit menu Setup Utility program 64 exiting Setup Utility program 67 expansion slots features 9 F fans features 8 features 7 ThinkServer EasyStartup program 70 firmware updating 80 flashing the BIOS 68 front bezel reinstalling 87 removing 87 front panel LED 17 locations 17 front panel board assembly replacing 147 front system fan replacing 149 229 front view of the server locations 15 FRU lists 179 G gaseous contamination 220 German gloss statement 226 getting help 213 getting information 213 getting service 213 guidelines 83 H hard disk drive status
238. rive backplane on the upper hard disk drive cage connect the P4 power connector of the power supply to the 8 pin power connector on the backplane Mini SAS signal cable connector Used to connect the mini SAS connector on one end of the mini SAS signal cable 36 ThinkServer Hardware Maintenance Manual Backplane for 2 5 inch hot swap hard disk drives This topic provides information to help you locate the connectors on the 2 5 inch hot swap hard disk drive backplane The following illustrations show the connectors on the 2 5 inch hot swap hard disk drive backplane H H A 5 Figure 21 Front view of the 2 5 inch hot swap hard disk drive backplane El Slot 0 for a 2 5 inch SAS hot swap hard disk Slot 4 for a 2 5 inch SAS hot swap hard disk drive drive H Slot 1 for a 2 5 inch SAS hot swap hard disk Slot 5 for 2 5 inch SAS hot swap hard disk drive drive Slot 2 for 2 5 inch SAS hot swap hard disk Slot 6 for 2 5 inch SAS hot swap hard disk drive drive E Slot 3 for a 2 5 inch SAS hot swap hard disk Slot 7 for a 2 5 inch SAS hot swap hard disk drive drive 09 oe Figure 22 Rear view of
239. rive bundle and instructions on how to install it refer to the documentation that comes with the RDX USB drive bundle In your server the P6 power connector of the power supply is for the RDX USB drive bundle You can purchase this option directly from Lenovo The option name is Lenovo Removable Disk Technology RDX USB Drive Bundle The RDX technology combines the characteristics of tape backup with disk storage to help you protect and archive data Expansion slots The server has four expansion slots on the system board For detailed information see System board components on page 42 Input Output 1 features One Video Graphics Array VGA DB 15 connector on the rear panel e Six USB 2 0 connectors two on the front panel and four on the rear panel Two RJ 45 Ethernet connectors on the rear panel Two serial connectors one fully functional serial connector on the rear panel and one internal serial connector on the system board for optional use For the location information about the connectors refer to the related topic in Locations on page 13 Video subsystem An integrated graphics controller in the Baseboard Management Controller BMC chip on the system board to support a VGA DB 15 connector on the rear panel for connecting video devices Ethernet connectivity The server comes with an integrated Intel Gigabit Ethernet controller as well as an Ethernet physical layer PHY of the Open Systems Interconnection model OSI
240. rive is an extra unused drive that is part of the disk subsystem It is usually in standby mode and ready for service if a drive fails Setting hot spare drives enables you to replace failing drives without performing a system shutdown operation For a detailed introduction to hot spare drives refer to Introduction to RAID in the MegaRAID SAS Software User Guide on the documentation DVD that comes with your server To set a physical drive as a hot spare drive using the LSI Software RAID Configuration Utility program do the following 1 Start the LSI Software RAID Configuration Utility program See Starting the LSI Software RAID Configuration Utility program on page 74 2 Do one of the following f you want to create or add a new RAID array you can set a hot spare drive during the configuration process by following the instructions on the screen f you want to set a hot spare drive right after the configuration select Objects Physical Drive from the program main interface Then select the physical drive that you want to set as a hot spare Chapter 5 Configuring the server 77 drive and press Enter A submenu is displayed Select Make Hot Spare from the submenu and then select Yes when prompted to set the physical drive as a hot spare drive Rebuilding a physical drive This topic provides instructions on how to rebuild a physical drive using the LSI Software RAID Configuration Utility program when a physical drive in an ar
241. rograms that are available for you to configure RAID This topic contains the following items e About RAID on page 72 e RAID for your server on page 73 e Configuring RAID using the ThinkServer EasyStartup program on page 74 e Configuring the onboard SATA software RAID on page 74 e Configuring the advanced SATA or SAS hardware RAID on page 79 Chapter 5 Configuring the server 71 About RAID RAID an acronym for Redundant Array of Independent Disks is a technology that provides increased storage functions and reliability through redundancy This is achieved by combining multiple hard disk drives into a logical unit where data is distributed across the drives in one of several ways called RAID levels When a group of independent physical hard disk drives are set up to use RAID technology they are in a RAID array This array distributes data across multiple hard disk drives but the array appears to the host server as one single storage unit Creating and using RAID arrays provides high performance such as the expedited I O performance because several drives can be accessed simultaneously RAID drive groups also improve data storage reliability and fault tolerance compared to single drive storage systems Data loss resulting from a drive failure can be prevented by reconstructing missing data from the remaining drives The following list describes some of the most commonly used RAID levels RAID O block le
242. ront door of the server 2 Locate the appropriate hard disk drive bay See Server components on page 25 120 ThinkServer Hardware Maintenance Manual 3 Press the release button to open the handle of the hot swap hard disk drive or the dummy tray m Figure 59 Opening the handle of the hot swap hard disk drive or the dummy tray 121 Chapter 6 Installing removing or replacing hardware 4 Pull the handle and carefully slide the hot swap hard disk drive or the dummy tray out of the front of the chassis Figure 60 Removing the hot swap hard disk drive or the dummy tray 5 Touch the static protective package that contains the new hot swap hard disk drive to any unpainted surface on the outside of the server Then take the new hot swap hard disk drive out of the package Note Do not touch the circuit board on the hard disk drive 122 ThinkServer Hardware Maintenance Manual 6 Slide the new hot swap hard disk drive into the drive bay from the front until it snaps into position and then completely close the handle Figure 61 Installing the hot swap hard disk drive 7 Check the hot swap hard disk drive status LEDs to make sure that the hard disk drive is operating correctly You might h
243. rsion of the BIOS Notes 1 The default settings are already optimized for you Use the default value for any item you are not familiar with Do not change the value of unfamiliar items or items that are not mentioned in this topic to avoid unexpected problems If you consider changing the server configuration proceed with extreme caution Setting the configuration incorrectly might cause unexpected results If you cannot turn on the server because of incorrect BIOS settings use the Clear CMOS Recovery jumper to recover the BIOS to the factory default settings or use the BIOS recovery jumper to boot the server from a BIOS recovery image and recover the BIOS to the version in the image See System board jumpers on page 46 Lenovo provides the BIOS update utility on the Lenovo Support Web site You can download the BIOS image and follow the instructions on the Web site to update the BIOS See Updating or recovering the BIOS on page 67 After updating the BIOS all the BIOS settings become the default settings of the updated BIOS version You need to check and reconfigure the BIOS settings for your specific needs If you have changed any hardware in the server you might need to reflash the BIOS the BMC firmware and the FRU SDR The following menus are listed on the BIOS Setup Utility screen Main See Main menu on page 56 Advanced See Advanced menu on page 57 Security See Security menu on page 60 Server Management
244. rtraglichkeit in den EU Mitgliedsstaaten und h lt die Grenzwerte der EN 55022 Klasse A ein Um dieses sicherzustellen sind die Gerate wie den Handb chern beschrieben zu installieren und zu betreiben Des Weiteren d rfen auch nur von der Lenovo empfohlene Kabel angeschlossen werden Lenovo bernimmt keine Verantwortung f r die Einhaltung der Schutzanforderungen wenn das Produkt ohne Zustimmung der Lenovo verandert bzw wenn Erweiterungskomponenten von Fremdherstellern ohne Empfehlung der Lenovo gesteckt eingebaut werden Deutschland Einhaltung des Gesetzes ber die elektromagnetische Vertraglichkeit von Betriebsmittein Dieses Produkt entspricht dem Gesetz ber die elektromagnetische Vertr glichkeit von Betriebsmitteln EMVG fr her Gesetz ber die elektromagnetische Vertr glichkeit von Ger ten Dies ist die Umsetzung der EU Richtlinie 2004 108 EG fr her 89 336 EWG in der Bundesrepublik Deutschland Zulassungsbescheinigung laut dem Deutschen Gesetz ber die elektromagnetische Vertr glichkeit von Betriebsmitteln EMVG vom 20 Juli 2007 fr her Gesetz ber die elektromagnetische Vertr glichkeit von Ger ten bzw der EG Richtlinie 2004 108 EC fr her 89 336 EWG f r Ger te der Klasse A Dieses Ger t ist berechtigt in bereinstimmung mit dem Deutschen EMVG das EG Konformit tszeichen CE zu f hren Verantwortlich f r die Konformitatserklarung nach Paragraf 5 des EMVG ist die Lenovo Deutschland
245. ructions on the screen e f you want to add a secondary RAID configuration select View Add Configuration and then follow the instructions on the screen to view the current configuration and add a new configuration f you want to delete the existing RAID configuration exit the program and back up all your data on the hard disk drives After backing up all your data enter the program main interface and select Clear Configuration Select Yes when prompted and follow the instructions on the screen 76 ThinkServer Hardware Maintenance Manual Attention Deleting the existing RAID configuration erases all data on the virtual drive Make sure that you back up all data before deleting the RAID array If the operating system is installed on the virtual drive you want to delete you need to reinstall the operating system after completing the operation f you want to delete the existing RAID configuration and make a new configuration exit the program and back up all your data on the hard disk drives After backing up all your data enter the program main interface and select New Configuration Select Yes when prompted to proceed and then follow the instructions on the screen Attention Deleting the existing RAID configuration erases all data on the virtual drive Make sure that you back up all data before deleting the RAID array If the operating system is installed on the virtual drive you want to delete you need to reinstall the operating syste
246. rver which might result in overheating or component damage Note The PCI cards are extremely sensitive to ESD Make sure that you read and understand Handling static sensitive devices on page 84 first and carefully perform the operation Installing a PCI card Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to install a PCI card Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Use any documentation that comes with the PCI card and follow those instructions in addition to the instructions in this topic To install a PCI card do the following Chapter 6 Installing removing or replacing hardware 93 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 3 Lay the server on its side for easier operation 4 Locate an appropriate PCI card slot on the system board See System board components on page 42 to identify the different types of PCI card slots in your server 5 Remove the PCI card slot bracket by removing the screw that secures the metal bracket and then lifting th
247. rver has one installed Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Notes 1 Use any documentation that comes with the TPM module and follow those instructions in addition to the instructions in this topic 2 If you remove the TPM module the TPM function is unavailable To remove the TPM module do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 110 ThinkServer Hardware Maintenance Manual 2 Remove the server cover See Removing the server cover on page 85 3 Lay the server on its side for easier operation 4 Locate the TPM connector on the system board and then remove the TPM module installed on the TPM connector by lifting it straight up Note Carefully handle the TPM module by its edges lm ml ESE eni pe Em Figure 50 Removing the TPM module 5 If you are instructed to return the old TPM module follow all packaging instructions and use
248. s from connectors Attach power cords to outlet Remove all cables from devices Turn devices ON Statement 2 7 bancer Danger of explosion if battery is incorrectly replaced When replacing the lithium coin cell battery use only the same or an equivalent type that is recommended by the manufacturer The battery contains lithium and can explode if not properly used handled or disposed of Do not Throw or immerse into water Heat to more than 100 C 212 F Repair or disassemble Dispose of the battery as required by local ordinances or regulations Copyright Lenovo 2011 Statement 3 A CAUTION When laser products such as CD ROMs DVD drives fiber optic devices or transmitters are installed note the following Do not remove the covers Removing the covers of the laser product could result in exposure to hazardous laser radiation There are no serviceable parts inside the device e Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure Some laser products contain an embedded Class or Class laser diode Note the following Laser radiation when open Do not stare into the beam do not view directly with optical instruments and avoid direct exposure to the beam Statement 4 A gt 18 kg 39 7 Ib gt 32 kg 70 5 Ib gt 55 kg 121 2 Ib 32 kg 70 5 Ib 55
249. select You can press F12 when turning on the server and select a temporary startup device directly from the boot device selection window See Selecting a startup device on page 66 Exit menu This topic provides information about the Exit menu in the Setup Utility program After you finish viewing or changing settings in the Setup Utility program you can choose one desired action from the Exit menu to save changes discard changes load default values and exit the program The following table lists each item on the Exit menu with descriptions Press Enter to select the item and then select Yes when prompted to confirm the action For information about exiting the Setup Utility program see Exiting the Setup Utility program on page 67 Exit menu items m 22 1 Setting the system date and time This topic provides instructions on how to set the system date and time in the Setup Utility program To set the system date and time in the Setup Utility program do the following 1 Start the Setup Utility program See Starting the Setup Utility program on page 55 2 On the Main menu select System Date or System Time 3 Use the Tab key to switch between data elements and type the numbers from the keyboard to set the system date and time 4 Press F10 to save settings and exit the Setup Utility program 64 ThinkServer Hardware Maintenance Manual Using passwords By using the Setup Utility program you can set a password
250. sers and servicers to install a secondary front system fan by themselves CAUTION Hazardous moving parts Keep fingers and other body parts away Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Depending on the model your server might look slightly different from the illustrations in this topic To replace the front system fan do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 3 Locate the front system fan 1 See Server components on page 25 4 Disconnect the front system fan 1 cable from the 4 pin system fan 1 connector on the system board See System board components on page 42 150 ThinkServer Hardware Maintenance Manual 5 Press the two tabs of the front system fan towards each other until the two tips aligned with the corresponding holes in the chassis Then carefully slide the front system fan out of the chassis Figure 86 Removing the front system fan 6 Touch the static protective package that contains the new front system fan to any unpainted surface on the outside of the server Then remove the new front system fan from the package 7 Pos
251. server If the USB keyboard is connected to a USB hub disconnect the keyboard from the hub and connect it directly to the server No keys are stuck The USB controller is enabled in the Setup Utility program See Using the Setup Utility program on page 55 2 Restart the server 176 ThinkServer Hardware Maintenance Manual pF S Rec the keyboard The mouse or pointing device does not work 1 Make sure that e The mouse or pointing device cable is securely connected to the server If the USB mouse or pointing device is connected to a USB hub disconnect the mouse or pointing device from the hub and connect it directly to the server The mouse or pointing device is clean and no dust accumulates The device drivers are installed correctly The USB controller is enabled in the Setup Utility program See Using the Setup Utility program on page 55 2 Restart the server 3 Replace the mouse or pointing device A USB device does not work Make sure that The USB cable is securely connected to the server If the USB device is connected to a USB hub disconnect the device from the hub and connect it directly to the server The device drivers are installed correctly The USB controller is enabled in the Setup Utility program See Using the Setup Utility program on page 55 Restart the server Replace the USB device POST error codes Each time you turn on the system it
252. services and software e Purchase upgrades and extended hardware repair services e Access the Lenovo Limited Warranty LLW e Access the online manuals for your products e Access troubleshooting and support information for your server model and other supported products Download the latest device drivers and software updates for your server model e Find the service and support phone numbers for your country or region e Find a Service Provider located near you Lenovo Support Web site Technical support information is available on the Lenovo Support Web site at http support lenovo com Copyright Lenovo 2011 213 This portal is updated with the latest information about the following subjects Download Drivers amp Software Download drivers flash the BIOS and update your software Diagnose amp Fix Use self diagnostic tools to diagnose the problem yourself search community boards or work with our Virtual Agent to answer questions Product amp Service Warranty Check your warranty status and upgrade your warranty Product amp Parts Detail Find part numbers for replacement parts learn how to replace parts and view other parts information related to your product User Guides amp Manuals Read or download the documentation related to your product Research amp Learn Search the community knowledge base for your computer to share and discover information with other users Help and service This topic co
253. some general information about your product This chapter contains the following items e Introduction on page 1 e Server documentation on page 1 Introduction This Hardware Maintenance Manual for your Lenovo ThinkServer product contains information about the server features specifications component locations configuration instructions hardware replacement procedures parts listing and troubleshooting and diagnostics Note The Hardware Maintenance Manual is intended only for trained service personnel of Lenovo The Hardware Maintenance Manual is updated frequently and the most up to date version is always available in English on the Lenovo Web site at http www lenovo com ThinkServerUserGuides This document contains instructions on how to install remove or replace Customer Replaceable Units CRUs and Field Replaceable Units FRUs Replaceable components are of three types Self service CRUs Self service CRUs are easy to install and customers are responsible for replacing all Self service CRUs If a Lenovo service technician installs a Self service CRU at your request you will be charged for the installation Optional service CRUs Although dealing with Optional service CRUs requires some technical skills Optional service CRUs are safe for customers to replace You may install an Optional service CRU yourself or request Lenovo to install it at no additional charge under the type of warranty servi
254. stalling 98 locations 33 removing 99 RAID configuration utilities software 13 rear system fan replacing 152 rear view of the server locations 19 rebuilding physical drive 78 recovering the BIOS 68 reinstalling front bezel 87 reliability availability and serviceability features 10 removing DIMM 92 DIT module 113 Ethernet card 97 front bezel 87 hardware 83 iKVM key 107 memory module 92 non hot swap hard disk drive 124 card 95 RAID 5 key on the RAID 101 RAID card 99 server cover 85 system board RAID 5 104 TPM module 110 replacing front panel board assembly 147 front system fan 149 hardware 83 heat sink and fan assembly 154 hot swap hard disk drive 119 hot swap hard disk drive backplane 133 hot swap redundant power supply module 140 microprocessor 157 non hot swap power supply assembly 137 optical drive 115 power distribution board and cage assembly 143 rear system fan 152 system board 162 system board battery 161 road map server setup 5 running consistency check 78 5 security front door lock 25 integrated cable lock 24 231 padlock 23 Security menu Setup Utility program 60 serial number label locations 13 Server components locations 25 server configuration updating 170 Server cover installing 168 removing 85 server documentation 1 server locks locations 22 Server Management menu Setup Utility program 61 Server package 7 server setup road map 5 Service getting 213
255. storage device battery pack assembl batteries A mech WAHLER circuit cards with mechs Fe mech H HBR circuit cards w o mechs Botat laser KK OK LX KX Tz BA ERUIT AE A EMERARA ERF SJT 11363 2006 FATHER Hl BEA indicates that the content of the toxic and hazardous substance in all the homogeneous materials of the part is below the concentration limit requirement as described in SJ T 11363 2006 X ana VIRIS BBL SJT 11363 2006 PATHE X indicates that the content of the toxic and hazardous substance in at least one homogeneous material of the part exceeds the concentration limit requirement as described in SJ T 11363 2006 CEPUP 79 77420 EPUP HEKRA RARE RRA E R FIERE Lenovo 2r Ge RIERA AE 495 EPUP FRERE TORRE TETE TE EN FENA m TAP m PERRE ARE u RAE WRAS BY HAJT RER T ARP EPUP Environmental Protection Use Period EPUP Disclaimer The number provided as the EPUP is provided solely to comply with applicable laws of the People s Republic of China It does not create any warranties or liabilities on behalf of Lenovo to customer The EPUP assumes that the product will be used under normal conditions in accordance with the Lenovo
256. t come with the options in addition to the instructions in this manual Make sure that you replace a failing fan within 48 hours e When replacing a hot swap drive install the new hot swap drive within two minutes of removal Working inside the server with the power on Attention Static electricity that is released to internal server components when the server is turned on might cause the server to halt which might result in the loss of data To avoid this potential problem always use an ESD wrist strap or other grounding system when you work inside the server with the power on The server supports hot swap devices and is designed to operate safely while it is turned on and the cover is removed Follow these guidelines when you work inside the server with the power on Avoid wearing loose fitting clothing on your forearms Button long sleeved shirts before working inside the server do not wear cuff links while you are working inside the server Do not allow your necktie or scarf to hang inside the server Remove jewelry such as bracelets necklaces rings and loose fitting wrist watches Remove items from your shirt pocket such as pens and pencils These items might fall into the server as you lean over it Avoid dropping any metallic objects into the server such as paper clips hairpins and screws Removing the server cover Attention Do not open your server or attempt any repair before reading and underst
257. t of band management EHI PCI Express x8 card slot PCI E slot 3 This is a PCI Express x8 lane in physical PCI 2 0 x8 slot that supports a PCI Express x8 card with 167 mm 6 57 inches in length such as an Ethernet card or a RAID card EJ PCI Express x8 card slot PCI E slot 4 This is a PCI Express x8 lane in physical PCI 2 0 x16 slot that supports a PCI Express x8 card with 312 mm 12 28 inches in length such as a graphics card Microprocessor fan connector Used to connect the heat sink and fan assembly cable System fan 3 connector Used to connect the rear system fan cable Microprocessor power connector Used to connect the 8 pin P2 power connector of the power supply to provide power to your microprocessor System board jumpers This topic provides information about the jumpers on the system board A jumper is a short length of conductor used to set up or adjust printed circuit boards such as the system board of a computer A jumper is usually encased in a non conductive block of plastic for convenient use and avoiding any possible damage to a live circuit Jumper pins arranged in groups on the system board are called jumper blocks When two or more jumper pins are capped with a jumper an electrical connection is made between them and the equipment is thus instructed to activate certain settings accordingly 46 ThinkServer Hardware Maintenance Manual The following illustration shows jumper in the default settin
258. t to release the system board RAID 5 key and then completely remove the key from the iButton socket Note necessary remove any parts or disconnect any cables that might impede your operation e pe Em Figure 46 Removing the system board RAID 5 key 5 If you are instructed to return the old system board RAID 5 key follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropriate section To complete the removal procedure go to Completing the parts replacement on page 168 As the onboard SATA software RAID 5 is not available without the system board RAID 5 key you might need to reconfigure RAID for your server See Configuring RAID on page 71 Installing or removing the ThinkServer iKVM Remote Management Module This topic provides instructions on how to install or remove the ThinkServer iKVM Remote Management Module hereinafter referred to as the iKVM key The iKVM key offers convenient remote KVM access and control through the LAN or Internet You can
259. taman tuotteen k ytt Avant d utiliser le produit veillez bien lire et comprendre les instructions de s curit multilingues figurant sur le DVD de documentation fourni avec le produit xpnoworroinosete OT xeve StaBdoel kal AOMAAELAC ot orio eq eivai yAWooEc oro DVD TekuNnpiwonc TIPOIOV Vor Verwendung des Produkts sollten Sie unbedingt die mehrsprachigen Sicherheitsanweisungen auf der Dokumentations DVD lesen die im Lieferumfang des Produkts enthalten ist nin o3n NINNIN RNAP rr egn AMA ym yn 197 yin jana Tina DVD 3 nowa niy omn A term k haszn lata el tt mindenk ppen olvassa el s rtelmezze a term khez kapott dokument ci s DVD lemezen tal lhat t bb nyelven elolvashat biztons gi el r sokat Prima di utilizzare il prodotto accertarsi di leggere e comprendere le informazioni sulla sicurezza multilingue disponibili sul DVD di documentazione fornito con il prodotto Documentation DVD dv UE EKKEL 01772 amp EOI Aina THULT FSW AES ALG Aol AES RA ALIS BA DVDs del 9 AAS AALA L Voordat u het product gebruikt moet u ervoor zorgen dat u de meertalige veiligheidsinstructies op de documentatie dvd van het product hebt
260. ted procedure in Chapter 6 Installing removing or replacing hardware on page 83 2 If an action step is preceded by Trained service technician only this action step is reserved for trained service technician and must be performed only by a trained service technician Com The amount of system memory that is displayed is less 1 Make sure that than the total capacity of the installed physical memory modules and you suspect a memory module problem All memory modules are the correct type supported by the server See Features on page T You follow the memory module installation rules See Memory module installation rules on page 90 All memory modules are seated correctly and securely The system firmware is up to date Run any diagnostic programs to test the memory modules Reinstall the memory modules 4 Replace the suspect memory modules Trained service technician only Replace the system board Keyboard mouse or USB device problems Follow the suggested actions for the corresponding symptom in the order in which they are listed until the problem is solved If none of these actions solve the problem see Troubleshooting procedure on page 171 for the subsequent steps you should check after using the information in this topic sytem Com All or some keys on the keyboard do not work 1 Make sure that The USB keyboard cable is securely connected to a USB connector on the
261. ted topics in Locations on page 13 ThinkServer EasyStartup program and ThinkServer EasyUpdate Firmware Updater program For more information about the software programs see Software on page 12 Wake on LAN When the Wake on LAN feature is enabled on a computer that is connected to a local area network LAN a network administrator can remotely turn on or wake up the computer from a management console using remote network management software Besides many other functions such as data transfer and software updates can be performed remotely without remote attendance and can be done after normal working hours and on weekends to save time and increase productivity Advanced system management features The BMC firmware supports the following advanced system management features Note The advanced system management features are only available when the BMC detects the presence of an integrated keyboard video and mouse iKVM key The iKVM key is a remote management module You can purchase an iKVM key from Lenovo and install it on the iKVM key connector on the system board of your server to enable the iKVM function and activate the advanced system management features iKVM redirection The BMC firmware supports iKVM redirection over LAN This feature is available remotely from the embedded Web server The remote management module can digitize and compress the collected keyboard video and mouse signals from the host system and then send them t
262. test the hard disk drives Make sure that the cable connection is correct See Connecting cables on page 38 Reconnect the power cable Reconnect the signal cable Replace the affected signal cable For hot swap hard disk drives if you suspect a problem with the backplane replace the affected backplane Remove the drive s that are not recognized by the diagnostic test Then run the hard disk drive diagnostic test again If the remaining drives are recognized replace the drive s that you removed Remove the hard disk drive that was being tested when the server stopped responding and run the diagnostic test again If the hard disk drive diagnostic test runs successfully replace the drive that you removed with a new one Reinstall all hard disk drives and reconnect cables Then run the hard disk drive diagnostic test Chapter 7 Troubleshooting and diagnostics 175 Memory module problems Follow the suggested actions for the corresponding symptom in the order in which they are listed until the problem is solved If none of these actions solve the problem see Troubleshooting procedure on page 171 for the subsequent steps you should check after using the information in this topic If the problem cannot be solved by yourself seek technical assistance See Chapter 9 Getting information help and service on page 213 Notes 1 If you are instructed to remove install or replace any CRUS refer to the rela
263. the 2 5 inch hot swap hard disk drive backplane 8 pin power connector Used to connect the P5 power connector of the power supply Chapter 3 Product overview 37 H Mini SAS signal cable connector 2 Used to connect the mini SAS connector on one end of the mini SAS signal cable Mini SAS signal cable connector 1 Used to connect the mini SAS connector on one end of the mini SAS signal cable Connecting cables This topic provides instructions on how to connect the mini SAS signal cable s to the hot swap hard disk drive backplane s and the system board or the required RAID card if you have one installed This topic applies only to server models that have hot swap hard disk drive s installed and the cable connections are different depending on the following configurations e Server models with five to eight 3 5 inch hot swap hard disk drives and two backplanes e Server models with up to eight 2 5 inch SAS hot swap hard disk drives and one backplane e Server models with up to four 3 5 inch hot swap hard disk drives and one backplane Server models with five to eight 3 5 inch hot swap hard disk drives and two backplanes For server models with five to eight SAS or SATA II 3 5 inch hot swap hard disk drives and two backplanes a required RAID card must be installed in the server The following cables that come with the RAID
264. the server cover See Removing the server cover on page 85 Lay the server on its side for easier operation Note down the component locations cable connections and cable routing in the server Remove all memory modules and PCI cards including the RAID card and Ethernet card that are currently installed See Removing a memory module on page 92 and Removing a PCI card on page 95 6 Remove the heat sink and fan assembly See Replacing the heat sink and fan assembly on page 154 Remove the TPM module if one is installed See Removing the TPM module on page 110 8 Remove the ThinkServer SATA Software RAID 5 key if one is installed See Removing the system 10 11 board RAID 5 key on page 104 Remove the ThinkServer iKVM Remote Management Module if one is installed See Removing the iKVM key on page 107 Remove the system board battery See Replacing the system board battery on page 161 Remove any other parts and disconnect all cables from the system board Chapter 6 Installing removing or replacing hardware 163 12 Remove the eight screws that secure the system board following the recommended numerical sequence as shown Then carefully remove the system board out of the chassis 5
265. tility program you must use the keyboard The keys used to perform various tasks are displayed on the bottom of each screen Use up and down arrow keys to navigate between items For most items the corresponding help message is displayed on the bottom of the screen when the item is selected If the item has submenus you can display the submenus by pressing Enter After entering the LSI Software RAID Configuration Utility program you can see the Management Menu on the screen The Management Menu contains the following menu items Configure This menu contains items to help you create a RAID array view the current RAID configuration add a new array delete an existing array or select a boot virtual drive e Initialize This menu helps you initialize virtual drive s Note Initializing a virtual drive erases all data on the virtual drive Back up any data you want to keep and ensure the operating system is not installed on the virtual drive before the initialization Objects This menu helps you configure parameters for the RAID adapter or controller the virtual drive s and the physical drive s Rebuild This menu helps you rebuild a physical drive in an array in the event of a physical drive failure You can choose to rebuild the data on the failing drive if the drive is still operational If the drive is not operational it must be replaced and the data on the failing drive must be rebuilt on a new drive to restore the system to
266. tions in addition to the instructions in this topic To install the RAID 5 key on the RAID card do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server 2 Remove the server cover See Removing the server cover on page 85 3 Lay the server on its side for easier operation 4 Locate the RAID card which is installed in the PCI E slot 3 on the system board See System board components on page 42 5 Remove any parts or disconnect any cables that might impede your operation 6 Touch the static protective package that contains the RAID 5 key to any unpainted surface on the outside of the server Then take the RAID 5 key out of the package Note Carefully handle the RAID 5 key by its edges 100 ThinkServer Hardware Maintenance Manual 7 Locate the RAID 5 key connector on the RAID and then insert the RAID 5 key into the connector You might want to remove the RAID card first install the RAID 5 key on the RAID card and then reinstall the RAID card See Installing or removing the RAID card on page 98 Note Make sure that the RAID 5 key is securely seated on the RAID card D Vi en Figure 43
267. to the Lenovo Support Web site at http support lenovo com Chapter 5 Configuring the server 67 Click Download Drivers amp Software follow the instructions on the Web page to locate the BIOS update utility program Download the ISO image or update package and the installation instructions in a TXT file If you will use an ISO image to update the BIOS use any CD or DVD burning software to create a bootable disc with the ISO image If you will use an update package to update the BIOS extract the package to a local drive and copy all the files to a bootable USB key Print the TXT file that contains the installation instructions You will need the instructions when performing the BIOS update or recovery procedure Updating flashing the BIOS This topic provides instructions on how to update flash the BIOS Notes 1 Update the BIOS on your server only if the newer BIOS version specifically solves a problem you have We do not recommend BIOS updates for servers that do not need it You can view the updated information for the new BIOS version in the installation instructions for the BIOS update utility program See Downloading the BIOS update utility program on page 67 Downgrading the BIOS to an earlier version is not recommended and might not be supported An earlier BIOS version might not contain the support for the latest system configurations If the power to your server is interrupted while the PO
268. tors on the rear panel of the server Attention To avoid component damage connect the power cord s last Note In most areas of the world Lenovo requires the return of the defective CRU Information about this will come with the CRU or will come a few days after the CRU arrives Updating the server configuration When you turn on the server for the first time after you install remove or replace a device you might need to update the server configuration Some optional devices have device drivers that you must install For information about installing device drivers use the documentation that comes with each optional device To obtain the supported device drivers for your server from the Lenovo Support Web site go to http support lenovo com Click Download Drivers amp Software and follow the instructions on the Web page to find the device drivers you want to download Refer to the following information resources to update the server configuration To update the BIOS configuration see Using the Setup Utility program on page 55 To update the RAID configuration see Configuring RAID on page 71 To use the ThinkServer EasyStartup program see Using the ThinkServer EasyStartup program on page 69 To update your system firmware see Updating the firmware on page 80 170 ThinkServer Hardware Maintenance Manual Chapter 7 Troubleshooting and diagnostics This chapter provides information about basic troublesho
269. u might need to reconfigure RAID for your server Refer to the MegaRAID SAS Software User Guide on the documentation DVD that comes with your server for information about how to configure the hardware RAID Installing or removing the ThinkServer SATA Software RAID 5 Key This topic provides instructions on how to install or remove the ThinkServer SATA Software RAID 5 Key hereinafter referred to as the system board RAID 5 key The system board RAID 5 key expands the capability of the system board by activating RAID 5 for the onboard SATA software RAID You can purchase a system board RAID 5 key directly from Lenovo Installing the system board RAID 5 key Attention Do not open your server or attempt any repair before reading and understanding the Safety information on page iii and Guidelines on page 83 This topic provides instructions on how to install the system board RAID 5 key 102 ThinkServer Hardware Maintenance Manual Before you begin print all the related instructions or ensure that you can view the PDF version on another computer for reference Note Use any documentation that comes with the system board RAID 5 key and follow those instructions in addition to the instructions in this topic To install the system board RAID 5 key do the following 1 Remove all media from the drives and turn off all attached devices and the server Then disconnect all power cords from electrical outlets and disconnect all cables th
270. ur server supports onboard SATA software RAID levels 0 1 and 10 You can also activate RAID 5 by installing a ThinkServer SATA Software RAID 5 activation key See Installing or removing the ThinkServer SATA Software RAID 5 Key on page 102 You can install and use the MegaRAID Storage Manager program to manage the RAID array and RAID controller in an operating system environment Starting the LSI Software RAID Configuration Utility program This topic provides instructions on how to start the LSI Software RAID Configuration Utility program To start the LSI Software RAID Configuration Utility program do the following 1 Start the Setup Utility program See Starting the Setup Utility program on page 55 2 On the Advanced menu select SATA Configuration gt SATA Mode 3 Select RAID Mode Then press F10 to save settings and exit the Setup Utility program 74 ThinkServer Hardware Maintenance Manual 4 When you see the message Press Ctrl M or Enter to run LSI Software RAID Setup Utility immediately press Ctrl M or Enter to start the LSI Software RAID Configuration Utility program LSI Software RAID Configuration Utility program interface This topic provides information about the menus and items in the LSI Software RAID Configuration Utility program Depending on the version of the program some menu or item information might differ slightly from the information in this topic When working with the LSI Software RAID Configuration U
271. uropea Esta etiqueta se aplica a varios productos para indicar que el producto no se va a desechar sino que va ser reclamado por esta Directiva una vez termine su ciclo de vida Los usuarios de los equipos el ctricos y electr nicos EEE con la marca WEEE por el Anexo IV de la Directiva WEEE no deben tratar los EEE como desperdicios municipales no clasificados una vez terminado su ciclo de vida sino que deben utilizar el marco de recogida disponible para devolver reciclar y recuperar los WEEE y minimizar los posibles efectos de los EEE en el medio ambiente y en la salud debidos a la presencia de substancias peligrosas Para obtener informaci n adicional acerca de WEEE consulte el sitio http Awww lenovo com lenovo environment Il marchio WEEE Waste Electrical and Electronic Equipment viene applicato soltanto ai paesi all interno dell unione europea EU e norvegia Le apparecchiature vengono etichettate in accordo con la direttiva europea 2002 96 EC riguardande lo smaltimento di apparecchiatura elettrica ed alettronica WEEE Le direttive determinano la procedura di restituzione e di riciclaggio delle apparecchiature usate in conformit con le normative dell unione europea Questa classificazione viene applicata a vari prodotti per indicare che il prodotto stesso non deve essere gettato ma riscattato al termine dell utilizzo per quasta direttiva Gli utenti di apparecchiature elettriche o elettroniche EEE marchiate WEEE secondo Annex IV della d
272. vel striping without parity or mirroring Simple stripe sets are normally referred to as RAID 0 RAID 0 uses striping to provide high data throughput especially for large files in an environment that does not require fault tolerance RAID 0 has no redundancy and it provides improved performance and additional storage without fault tolerance Any drive failure destroys the array and the likelihood of failure increases with more drives in the array RAID 0 does not implement error checking so any error is uncorrectable More drives the array means higher bandwidth but greater risk of data loss RAID 0 requires a minimum number of two hard disk drives RAID 1 mirroring without parity or striping RAID 1 uses mirroring so that data written to one drive is simultaneously written to another drive This is good for small databases or other applications that require small capacity but complete data redundancy RAID 1 provides fault tolerance from disk errors or failures and continues to operate as long as at least one drive in the mirrored set is functioning With appropriate operating system support there can be increased read performance and only a minimal write performance reduction RAID 1 requires a minimum number of two hard disk drives RAID 5 block level striping with distributed parity RAID 5 uses disk striping and parity data across all drives distributed parity to provide high data throughput especially for small random access R
273. ver Hardware Maintenance Manual Front panel This topic provides information to help you locate the control connectors and LEDs on the front panel of the server The following illustration shows the control connectors and LEDs on the front panel of the server Depending on the model your server might look slightly different from the following illustration Figure 4 Front panel Power switch with power status LED System status LED H Hard disk drive status LED Front USB connector 1 Ell Network Interface Controller NIC 1 status LED Front USB connector 2 Power switch with power status LED You can press the power switch to turn on the server when you finish setting up the server You can also hold the power switch for several seconds to turn off the server if you cannot turn off the server from the operating system See Chapter 4 Turning on and turning off the server on page 53 The power status LED helps you to determine the current power status Chapter 3 Product overview 17 Power status LED Description Blinking Green The server is in ACPI S1 mode which is also known as Power On Suspend POS mode In this mode the microprocessor is not working while other hardware devices are still working Hard disk drive status LED The hard disk drive status LED helps you to determine the status of the hard disk drive activity Blinking Gre
274. w microprocessor from the protective cover that protects the gold contacts on the bottom of the new microprocessor Note Do not touch the pins on the microprocessor socket and the gold contacts on the bottom of the new microprocessor Figure 94 Do not touch the pins Chapter 6 Installing removing or replacing hardware 159 10 Hold the new microprocessor by its edges and align the notches the new microprocessor with the tabs the microprocessor socket Then carefully lower the new microprocessor straight down into the microprocessor socket Note The small triangle Ell on one corner of the new microprocessor is the microprocessor orientation indicator The new microprocessor is in the correct orientation when this indicator faces toward the beveled corner Ell of the microprocessor socket Figure 95 Installing the microprocessor 11 Close the microprocessor retainer Gently press down the small handle and then push the handle inward to lock the retainer into position and secure the new microprocessor in the socket Figure 96 Securing the microprocessor in the socket 12 Reinstall the heat sink and fan assembly See Replacing the heat sink and fan assembly on page 154 13 If you are instructed to return the old microprocessor follow all packaging instructions and use any packaging materials that are supplied to you for shipping What to do next To work with another piece of hardware go to the appropri
275. words on page 65 Manufacturing jumper Reserved for the manufacturer Chapter 3 Product overview 49 System board LEDs This topic helps you locate the LEDs on the system board The following illustration shows the BMC status LED system board hardware fault LED and the POST code diagnostic LEDs on the system board E n H H E E Ee 4 ENIM 8 QE A Figure 30 System board LEDs System board hardware fault LED code diagnostic LED 1 H BNC status LED POST code diagnostic LED 6 POST code diagnostic LED 4 POST code diagnostic LED 2 POST code diagnostic LED 0 Least Significant JJ POST code diagnostic LED 7 Most Significant Bit MSB Bit LSB POST code diagnostic LED 5 POST code diagnostic LED 3 Ell System board hardware fault LED When this LED is lit it indicates that the system board hardware has failed 50 ThinkServer Hardware Maintenance Manual H BMC status LED This LED indicates the BMC status of your
276. y module For a list of the ThinkServer memory module options go to http www lenovo com thinkserver Click the Products tab and then click Options gt ThinkServer Memory to view the information Note The memory modules are extremely sensitive to ESD Make sure that you read and understand Handling static sensitive devices on page 84 first and carefully perform the operation Chapter 6 Installing removing or replacing hardware 89 Memory module installation rules Your server has four memory slots for installing or replacing DDR3 UDIMMs with ECC technology e Supports 2 GB and 4 GB 1333 MHz DDR3 UDIMMs Single rank or dual rank Minimum system memory 2 GB only one 2 GB memory module installed in the DIMMA2 slot Maximum system memory 16 GB 4 GB memory module installed in each of the four memory slots The following illustration helps you to locate the memory slots on the system board SEL 12 2 4j a D Figure 36 Memory slots on the system board
277. y releasing the three plastic tabs on the left side and pivoting the front bezel outward Figure 34 Removing the front bezel 88 ThinkServer Hardware Maintenance Manual 4 To reinstall the front bezel align the other three plastic tabs on the right side of the front bezel with the corresponding holes in the chassis then pivot the front bezel inward until it snaps into position on the left side LL 7 275 D I Figure 35 Installing the front bezel 5 Go to Completing the parts replacement on page 168 Installing removing or replacing hardware This topic provides instructions on how to install remove or replace hardware for your server You can expand the capabilities of your server by adding new hardware devices such as memory modules PCI cards or other server options and maintain your server by replacing the failing hardware devices If you are handling a server option refer to the appropriate installation and or removal instructions in this topic along with the instructions that come with the option Notes 1 Use only parts provided by Lenovo 2 Depending on the model your server might look slightly different from the illustrations in this topic Installing or removing a memory module This topic provides instructions on how to install or remove a memor
278. ystem e Press the power switch on the front panel to start an orderly shutdown of the operating system and turn off the server if your operating system supports this feature f your server stops responding and you cannot turn it off press and hold the power switch on the front panel for four seconds or more If you still cannot turn off the server disconnect all power cords from the server f the server is connected to a LAN a network administrator can remotely turn off the server from a management console using remote network management software You can also use the related BMC feature to remotely turn off the server through the management LAN The server might be turned off as an automatic response to a critical system failure Notes 1 When you turn off the server and leave it connected to an ac power source the server can also respond to a remote request to turn on the server To remove all power from the server you must disconnect the server from the ac power source Copyright Lenovo 2011 53 2 For information about your specific operating system refer to the related documentation or help system for the operating system 54 ThinkServer Hardware Maintenance Manual Chapter 5 Configuring the server This chapter provides the following information to help you configure the server e Using the Setup Utility program on page 55 e Using the ThinkServer EasyStartup program on page 69 e Configuri

Lenovo 388 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents