Lanzar Car Audio VBD500 User's Manual
Contents
1. EJECT Press EJECT button 4 to stop CD play and eject the disc from the slot NOTE ON CD R CD RW DISCS On this unit in addition to an audio CD you can play your original CD R or CD RW that contain audio titles However depending on the conditions of the recording equipment or the CD R CD RW disc itself some CD Rs or CD RWs cannot be played on this unit e DO NOT stick paper or tape etc onto the label side or the recording side of any CD R CD RW as it may cause a malfunction REMOTE CONTROL HANDSET o G0 CID OC o 9 co O 9 2 oool 9 A CONTROL 8 FUNCTION KEYS eI o BRD ou ci da ci kk QD POWER Power ON OFF Button MOD Mode Button S SEL Select Button DSP Display Button BND Band Select Button AMS Automatically Memory Storing amp Program Scanning Button VOL Volume Up Button VOL Volume Down Button TUN SEK Tune Seek Up Button TUN SEK 44 Tune Seek Down Button M1 M6 Preset Buttons PAU Pause Button SCN Scanning Button RPT Repeat Button SHF Shuffle Button SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls Bass at 100 Hz Treble at 10 KHz Maximum Output Power Current Drain CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response RADIO Frequency Coverage2. All the function buttons do not operate Error symbol on the display Note If press RESET button 27 the unit can t work yet please use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the front panel 8 RADIO OPERATION BAND SELECTION At tuner mode press LOU BND button 14 shortly to select the desired band The reception band will change in the following order gt FM1 FM2 FM3 AM STATION SELECTION Press MAN SEK button 17 or MAN SEK button 18 shortly to activate automatic seek function Press for several seconds until MANUAL appeared on the display the manual tuning mode is selected If both buttons have not pressed for several seconds they will retune to seek tuning mode and AUTO appeared on the display LOCAL DISTANCE Press LOC button 2 to select between local and distant stations Local setting for reception of strong station and a distant setting for reception of weaker stations This function is effect during AUTO SEEK operation AUTOMATICALLY MEMORY STORING amp PROGRAM SCANNING Automatic Memory Storing Press AMS button 19 the radio searches from the current frequency and checks the signal strength until one cycle search is finished And then 6 strongest stations are stored into the corresponding preset number button Program Scanning Press AMS button 19 shortly to scan preset station When the field strength level is
3. Sensitivity S N 30 dB Stereo Separation Frequency Coverage IF Sensitivity S N 20 dB DC 12 Volts Negative Ground 178 W x 163 D x 50 H 10 dB 10 dB 10 dB 10 dB 50W x 4 ch 15 Ampere More than 60 dB More than 60 dB 20 Hz 20 KHz FM 87 5 to 107 9 MHz 10 7 MHz 3 uV gt 30 dB AM 530 to 1710 KHz 450 KHz 32 dBu TROUBLE SHOOTING Before going through the check list check wiring connection If any of the problems persist after check list has been made consult your nearest service dealer Symptom Cause Solution No power The car ignition is not on If the power supply is properly connected to the car accessory terminal switch the ignition key to The fuse is blown Replace the fuse Disc cannot Presence of CD disc Remove the disc in the player then be loaded or inside the player put anew one ejected Inserting the disc in Insert the compact disc with the reverse direction label facing upward Compact disc is extremely Clean the disc or try to play a new dirty or defective disc one Temperature inside the Cool off or until the ambient car is too high temperature return to normal Condensation Leave the player off for an hour or so then try again No sound Volume is in minimum Adjust volume to a desired level The operation Wiring is not properly connected The built in microcomputer Check wiring c
4. mounting bracket Dashboard or Console 5 Note The mounting box outer trim ring and half sleeve are not used for method B installation Hook Remove this part USING THE DETACHABLE FRONT PANEL To Detach the Front Panel 1 Press the open button open then the front panel will be folded down Front Panel 3 For safekeeping store the front panel in the supplied protective case immediately after being removed Protective case Front panel 4 Push the front metal plate into the main body A click sound should be heard To Reinstall the Front Panel 1 2 Push the front panel into the main body click sound should be heard Note that if the front panel fails to lock in position properly press control button may not function and LCD display may be missing some segments Pushing the open button and then reinstall the front panel again Precautions when Handling 1 2 Do not drop the front panel Do not put pressure on the display or control buttons when detaching or reinstalling the front panel Do not touch the contacts on the front panel or on the main unit body It may result in poor electrical contact If any dirt or foreign substances adhered on the contacts they can be removed with a clean and dry cloth Do not expose the front panel to high temperatures or direct sunlight in anywhere Keep away any volatile agents e g benzene thinner or insecti
5. SL OWNER S MANUAL PLL SYNTHESIZER STEREO RADIO WITH COMPACT DISC PLAYER DIGITAL VBD 500 INSTALLATION Notes e Choose the mounting location where the unit will not interfere with the normal driving function of the driver Before finally installing the unit connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly Use only the parts included with the unit to ensure proper installation The use of unauthorized parts can cause malfunctions Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle Install the unit where it does not get in the driver s way and cannot injure the passenger if there is a sudden stop like an emergency stop If installation angle exceeds 30 from horizontal the unit might not give its optimum performance 30 e Avoid installing the unit where it would be subject to high temperature such as from direct sunlight or from hot air from the heater or where it would be subject to dust dirt or excessive vibration DIN FRONT REAR MOUNT This unit can be properly installed either from Front conventional DIN Front mount or Rear DIN Rear mount installation utilizing threaded screw holes at the sides of the unit chassis For details refer to the following illustrated installation method
6. cides from touching the surface of the front panel Do not attempt to disassemble the front panel WIRING CONNECTION MAIN UNIT ANTENNA CONNECTOR T Ip SUBWOOFER CABLE atr p IGNITION RED qu SWITCH B l MEMORY YELLOW Ei BACK UP GREY BLACK GROUND B RCA CABLE Rch RED Lch WHITE POWER BLUE ANTENNA WHITE GREY FRONT Lch FRONT Rch SPEAKER WHITE BLACK GREY BLACK SPEAKER GREEN VIOLET REAR Lch REAR Rch SPEAKER ES GREEN BLACK VIOLET BLACK SPEAKER OPERATION GENERAL OPERATION ON OFF Switch on the unit by pressing any button except OPEN button 7 and EJECT button 4 When system is on press PWR button 9 to turn off the unit FACEPLATE RELEASE Press OPEN button 7 to detach the removable faceplate 7 SOUND ADJUSTMENT Press SEL button 11 to select the desired adjustment mode The adjustment mode will change in the following order r Volume Bass Treble Balance Fader By pressing VOLUME A button 12 or VOLUME Y button 13 it is possible to adjust the desired sound guality LOUDNESS Press LOU BND button 14 for several seconds to reinforce the bass output and display will show LOUD Pr
7. ess it for several seconds again to release this function e SET THE CLOCK Holding down the DSP button 16 until the clock is shown on the LCD display and flashed Then press the MAN SEK i button 18 to change hours MAN SEK te button 17 to change minutes SELECT MODE Press MOD button 6 to choose desired listening mode e g radio mode to CD mode SUBWOOFER Press MOD SW button 6 for several seconds to toggle subwoofer output When subwoofer on display will show SW Press it again for several seconds to release this mode MUTE Press MUT button 10 to silence the receiver Press it again to resume listening LIOUID CRYSTAL DISPLAY Exhibit current freguency and activated functions on the display 8 EGUALIZATION Press EG button 20 to turn on egualization function and to select desired audio mode There are five kinds of mode as below FLAT CLASSICS POP M ROCK M DSP OFF 4 REMOTE SENSOR Point the remote control handset to the remote sensor IR sensor 26 Press the function keys on the handset to control the system FLASHING LED If the front panel does not install in the unit the LED 25 will be flashing RESET Reset button 27 is placed on the front panel and must be activated with either a ball point pen or thin metal object The reset button is to be activated for the following reasons Initial installation of the unit when all wiring is completed
8. more than the threshold level of stop level the radio is holding at that preset number for several seconds with releasing mute then searches again STATION STORING Press any one of the preset buttons 15 M1 to M6 to select a station which had been stored in the memory Press this button for several seconds current station is stored into the number button MONO STEREO Press MON button 3 to select mono or stereo mode You can sometimes improve reception of distant stations by selection mono operation e SCAN Press SCAN button 1 to set the function to scan mode which scanning to higher frequency station with receivable signal and keep on each station for several seconds CD OPERATION e SELECT TRACKS Press MAN SEK button 17 or 18 to move to the previous track or the following track Track number shows on display Hold MAN SEK button 17 or 18 to fast reverse or fast forward CD play starts from when you release the button e STOP PLAYING Press PAU button 21 to pause CD player Press it again to resume play REPEAT THE SAME TRACK Press RPT button 23 to continuously repeat the same track Press again to stop repeat PREVIEW ALL TRACKS Press SCN button 22 to play first several seconds of each track on the current disc Press again to stop intro and listen to track PLAY ALL TRACKS IN RANDOM Press SHF button 24 to play all tracks on CD in random order Press again to cancel the function
9. onnection Press the RESET button keys do not is not operating properly Front panel is not properly fixed into Work due to noise its place Sound skips The installation angle is Adjust the installation angle to less more than 30 degrees than 30 degrees The disc is extremely dirty or defective disc Clean the compact disc Then try to play a new one The radio does not work The radio station automatic selection does not work The antenna cable is not connected Insert the antenna cable firmly The signals are too weak Select a station manually www lanzar com 88 C0660 22
10. s DIN FRONT MOUNT Method A Installation the unit 1 Dashboard 2 Holder After inserting the holder into the dashboard select the appropriate tab according to the thickness of the dashboard material and bend them inwards to secure the holder in place Fig 1 3 Screw DIN REAR MOUNT Method B o o wn Dashboard Nut 5mm Spring washer Screw 5 x 25mm Screw Strap Be sure to use the strap to secure the back of the unit in place The strap can be bent by hand to the desired angle Plain washer Frame Insert fingers into the groove in the front of frame and pull out to remove the frame When re attaching the frame point the side with a groove downwards and attach it Lever Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click Pulling the levers makes it possible to remove the unit from the dashboard Installation using the screw holes on the sides of the unit A OO N 3 Fastening the unit to the factory radio mounting bracket 1 Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned are fitted and tighten the screws at 2 places on each side Use either truss screws 5 x 6mm or flush surface screws 4 x 6mm depending on the shape of the screw holes in the bracket Screw Factory radio
Download Pdf Manuals
Related Search