Home
Land Pride ZRP52 User's Manual
Contents
1. Deck Top View Bottom View Maintenance Locations Figure 4 1 22 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Table of Contents Section 4 Maintenance and Lubrication Maintenance Schedule Service at Intervals Indi Weekly or Monthly or Annually or cated every 50 Hours every 100 Hours every 500 Hours Verify Safety Start Interlock System Visually Inspect Unit for loose hardware and or damaged parts Visually Inspect Tires Daily Check Oil Level Engine 1 Daily or every 4 hours Clean Air Intake Screen 5 Daily or every 4 hours Clean Oil Heat Exchanger 5 Daily or every 4 hours Check Fuel Level Daily Blades Sharpen amp Securely Fastened Daily Discharge Chute Securely In Place amp Daily In Lowest Position Replace Remote Air Cleaner paper As needed element 5 Grease Deck Pusher Arms Grease Pump Idler Grease Deck Height Pivots Grease Gauge Wheel Bearings Change Engine Oil amp Filter 1 4 Clean Cylinder And Head Fins 8 Check Battery Connections Check Tire Pressure With A Gauge Check Hydraulic Oil Level Clean
2. Copyright 2008 All rights Reserved Land Pride provides this publication as is without warranty of any kind either expressed or implied While every precaution has been taken in the preparation of this manual Land Pride assumes no responsibility for errors or omissions Neither is any liability assumed for damages resulting from the use of the information contained herein Land Pride reserves the right to revise and improve its products as it sees fit This publication describes the state of this product at the time of its publication and may not reflect re product in ne future The illustrations in this manual are not intended for safe and proper assembly or disassembly of equipment The illustrations are intended for ordering parts only Land Pride and Accu Z Razor are registered trademarks All other brands and product names are trademarks or registered trademarks of their respective holders Printed in the United States of America ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Important Safety Information Table of Contents These are common practices that may or may not be applicable to the products described in this manual Be Aware of Signal Words A signal word designates a degree or level of hazard seriousness The signal words are DANGER Indicates an imminently hazardous situation which if not avoided will result in death or serious injury This signal word is limi
3. Ae A ROTATING BLADE HAZARD o Keep Away Rotating Blades o To prevent serious injury or death from thrown object e defie d er terngricetletine den 838 308C animals or buildings when operating 7 e Do not place hands or feet under deck when Warning Rotating Blade operating or when engine is running Hazard Both S id es Sw800 Warning General 838 399C Warning Fuel Imbedded in Fuel Tank 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 5 Table of Contents Introduction Land Pride Land Pride welcomes you to the growing family of new product owners This mower has been designed with care and built by skilled workers using quality materials Proper assembly maintenance and safe operating practices will help you get years of satisfactory use from this mower Application The Accu Z Razor Pro Mowers from Land Pride are compact in size and ideal for homeowner and light duty commercial grass maintenance The Razor Pro is a true zero turn mower When mowing alongside a building or landscaping the Razor Pro turns within its own width allowing you to turn away and not hit anything with the rear end Also the steering lever heights are adjustable making the mower comfortable to handle Using This Manual e This Operator s Manual is designed to help familiarize you with safety assembly operation adjustments troubleshooting and maintenance Read this manual entirely pri
4. N m ftHb mm x pitch 1 4 28 6 13 M6X1 5 16 18 15 11 24 M8 X 1 25 5 16 24 3 8 16 pae aa M10X1 5 33 24 52 17 13 26 19 3 8 31 22 47 35 M10 X 0 75 39 29 61 7 16 14 43 32 67 49 M12 X 1 75 58 42 91 7 16 20 49 36 M12 X 1 5 60 44 95 70 5 55 1 2 13 e e 145 105 M12X1 90 66 105 145 105 1 2 20 T 115 165 120 M14 X2 92 68 145 105 9 16 12 95 70 150 110 210 155 M14 X 1 5 99 73 155 115 215 160 9 16 18 105 79 165 120 235 170 M16 X2 145 105 225 165 315 230 mos sis f ao eo 05 as 5 8 18 150 110 M18 X 2 5 195 145 3 4 10 235 170 M18 X 1 5 220 165 3 4 16 260 190 M20 X 2 5 280 Dienas f ee zo eso a e ee M24 X 3 1050 780 1230 910 M24 X 2 830 610 1150 845 1350 995 M30 X 3 5 1510 1120 2100 1550 aer a e e r e 1 1 8 12 1210 1960 1440 M36 X 3 5 1730 1270 2650 1950 3660 2700 1 1 4 1520 1120 2460 1820 1880 1380 2960 2190 4100 3220 1 1 4 1680 1240 2730 2010 ae eae ea 1 in tpi nominal thread dia in inches threads per inch 1 3 8 1010 745 2270 1670 3680 2710 2 N m newton meters 11 2 6 1180 870 2640 1950 4290 3160 3 ft lb foot pounds a 2a 1330 980 2970 2190 4820 3560 4mm x pitch nominal thread dia in millimeters x thread pitch Torque tolerance 0 15 of torquing values Unless otherwise specified use torque values listed above Tire Inflation Chart Inflation PSI Drive Wheels 8 12 Gauge Wheels 8 12 7 14 08 ZRP44
5. be placed ao labels to be affixed to the replaced component as specified by Land Pride When ordering new components make sure the correct safety labels are included in the request To order new labels go to your Land Pride dealer To install new labels a Clean the area the label is to be placed Peel backing from label Press firmly onto the surface Squeeze out air bubbles with the edge of a credit card 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 3 Table of Contents Land Pride Important Safety Information 838 303C Danger Battery Beneath Seat ULE E CARIN V A NAL a V4 M WNL Vl gt 1 pam AEE S P EE E 838 305C Warning Rollover Hazard Beneath Bumper on Back of Frame 838 306C Warning Do not operate without deflector Hr ADI ams AV GUARD MISSING When this is visible DO NOT OPERATE ENTANGLEMENT HAZARD con cause Serious Injury or Death Si no entiende ingles se prefiere que busque a alguien que interprete las instrucciones para usted PHDC 6 818 543C Danger Guard is missing Beneath foot pan on mower deck 4 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Table of Contents Important Safety Information Warning Moving Parts Both Sides AF ska a
6. 9 Store mower in a clean dry place Preparation of Engine for Storage When engine is to be unused for long periods proceed as follows 1 Run engine for a minimum of 15 minutes 2 Drain oil from crankcase while engine is still warm 3 Refill with fresh oil of proper viscosity 4 Drain fuel tank and run the engine until it stops from lack of fuel Gasoline evaporates if left in carburetor for long periods forming gum and varnish deposits in carburetor These deposits will cause engine flooding and loss of power 5 Remove and replace fuel filter if not done in previous 100 hours 6 Remove spark plugs and pour a tablespoon of engine oil into each spark plug hole Install plugs but do not reconnect plug leads 7 Crank engine with starter at least a dozen revolutions to distribute oil over cylinder walls and valve mechanism 8 Clean exterior surface of engine Spread a light film of oil over any exposed metal surfaces of engine that are subject to corrosion 9 Clean dirt and chaff from cylinders and fins blower housing and muffler 10 Check oil filler cap and fuel tank cap to make certain they are securely in place New Season Preparation Before starting the mower following post season storage the following servicing is required 1 Clean mower removing trash and dirt accumulation 2 Check engine oil level 3 Fill fuel tank with fresh gasoline Run machine at half speed for 5 minutes checking operat
7. Engine Exterior 8 X X X X X XxX OKT OK Xx Clean And Re gap Spark Plugs 8 Check Pump Belt and Deck Belt for Tension and Condition 6 Check Fuel And Hydraulic Lines 7 Check Fuel Valve And Grommet 7 Tighten Lug Nuts On Wheels 2 Change Fuel Filter Clean or Replace Hydraulic Fill Cap Change Hydraulic Filter And Oil 3 Replace Spark Plugs NOTES 1 Initial oil change is after 5 hours of operation Thereafter change oil after every 40 hours of operation Change more often under dusty or dirty conditions and during hot weather periods 2 Torque initially and retorque after first 2 hours of operation Perform initial hydraulic filter change after 50 hours one week of operation 4 Change engine oil filter per the engine manufacturer s recommendations Refer to Engine Owner s Manual for recommendations and other maintenance items 5 Service more often under dusty or dirty conditions Use caution when servicing to prevent dust contamination in the engine Do not clean filter element Replace with a new one 6 Inspect every 100 hours and replace if worn or cracking is noticed Otherwise replace every 1000 hours or 2 years whichever comes first 7 Check fuel line hoses fuel valve and grommet for any cracks or leaks 8 Refer to Engine Owners Manual o 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 23 Table of Contents Section 4 Maintena
8. Figure 3 6 2 Raise and block the tractor up so the drive wheels are off of the floor 3 Refer to Figure 3 7 Open the hydraulic pumps bypass valve on the side that is being adjusted by turning bypass valve counter clockwise one half to one revolution The valve stems on each hydraulic pump are located near the top and are identified as a hex stud Figure 3 7 4 Rotate the tire The tire should rotate Remember hydraulic oil resistance will prevent the tire from rotating freely even with the bypass valves open There should be no resistance from the brakes at this point 5 Refer to Figure 3 8 Move the control lever to where it is just inside 1 8 the park brake slot Park Brake Control Lever 21070 Control Lever Position Figure 3 8 NOTE Refer to Figure 3 9 When the control lever is against the outside edge of the slot the brakes should not be engaged Park Brake Slot Outside Edge 21071 E Control Lever Position Figure 3 9 6 Rotate the tire If the brake is adjusted properly the tire will still rotate but friction will start to become noticeable here However if no brake resistance is noticed the brake needs adjusted as follows Actual body and frame colors may be different than what is represented in the picture 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 17 Table of Contents Section 3 Adjustments Land Pride 7 Refer to Figure 3 10 Lo
9. Figure 4 8B The fuel filter is installed in the fuel line between fuel tanks and engine fuel pump Replace filter Land Pride Part No 831 031C annually or after every 500 hours of operation whichever occurs first When replacing the fuel filter check the fuel line hoses and fuel shut off valve grommet for any cracks or leaks A fuel shut off valve is located on each fuel tank Figure 4 7 Close these valves to prevent fuel flow to the engine Kawasaki Engine Fuel Filter Figure 4 8A Honda Engine Fuel Filter Figure 4 8B 28 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Section 4 Maintenance and Lubrication Table of Contents Engine Oil and Filter Refer to Figure 4 9A and Figure 4 9B Check engine oil daily and after every 4 hours of operation Crankcase dipstick and oil filler tube are located at the rear of the machine Mower must be sitting level when checking oil Refer to engine manual and maintenance schedule for oil recommendation and capacities Change engine oil and filter after the first 5 hours of operation and after that per the engine manufacturer s recommendations It is recommended oil be changed more frequently if the mower is operated in extremely dirty conditions The oil drain and oil filter are located at the rear of the engine Bumper Removed for Clarity Do not Operate without Bumper Oil Filter Engine Oil Filler Tube Kawasaki Engine Oil Filte
10. Starting motor does not crank Control handles not in park brake position out or switch not adjusted Blade Engagement switch engaged Place control handle in park brake position or re adjust switch Disengage blade switch Weak or dead battery Recharge or replace For additional causes See engine manual Engine cranks but does not start Engine Runs with continuous misfiring or engine runs unevenly or erratically Loss of power or system will not operate in either direction No fuel or line plugged Numerous One fuel tank is empty Numerous Restrictions in air cleaner Fill f or replace line See engine manual Switch Left Right tank valve Open shut off valves on bottom of tanks by turning counter clockwise See Figure 4 7 on page 28 See engine manual Service air cleaner Internal interference or leakage in Hydro Drive Internal interference or leakage in wheel motor See your dealer See your dealer Insufficient hydraulic oil supply Check oil level in reservoir Have dealer check hydraulic drive Poor compression Steering linkage needs adjustment Air in system For additional causes See your dealer Adjust linkage Check filter amp fittings See engine manual Overheating Low oil pressure Air intake screen or cleaning fins clogged For additional causes Low oil level Oil diluted or too light Clean screen and fin See engine manual Add oil
11. deck lift pedal is used to raise or lower the deck Push on the pedal to raise the deck and then place the deck height locking pin into the desired cutting height hole Push the deck lift pedal to raise the deck when going over obstructions Deck Lift Deck Lift Pedal Figure 2 6 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 9 Table of Contents Section 2 Operating Land Pride Instrumentation Oil Pressure Light Refer to Figure 2 2 This light comes on when the ignition switch is placed in the RUN position and stays lit until the engine is running and a safe oil pressure is developed If light comes on during operation shut engine off immediately locate and correct the problem Electronic Hour Meter Refer to Figure 2 7 The hour meter is located on the right side behind the seat and registers in 1 10 hour increments up to 9 999 9 total hours Connected to the ignition switch the meter records the accumulative time while the ignition key is switched to the RUN position and the operator is on the seat Electronic Hour Meter Figure 2 7 Safety Start Interlock System The mower is equipped with a safety start interlock system consisting of park brake switches seat switch and blade engagement switch Check mower safety start interlock system each day prior to operation This system is an important mower safety feature and should be repaired immediately if it is malfunctioning Th
12. down in 1 2 increments using the different axle mount holes in the roller mount bracket When adjusting the rear anti scalp wheels the wheel should be in the lower axle mount hole when the front antiscalp wheels are in the lower or middle axle mount holes When the front wheels are in the upper axle mount hole the rear wheels should be in the upper axle mount hole as well NOTE When the anti scalp rollers are installed the minimum cutting height is 1 1 2 with the anti scalp rollers set at 3 4 Adjusting Holes Anti Scalp Rollers Anti Scalp Roller Adjustment Figure 3 21 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 21 Table of Contents Land Pride Section 4 Maintenance and Lubrication Engine Oil Fill amp Dipstick Fuel Filter Kawasaki Fuel Filter Honda Engine Air Cleaner Engine Oil Drain Plug Battery Fuel Tanks Hydraulic Oil Reservoir Deck Pusher Arms Zerks 2 Hydraulic Oil Filter 13 W gt OSNDAPWNY N 10 Gauge Wheel Bearing Zerks 2 11 Engine Oil Filter 12 Deck Height Pivot Zerks 4 13 Park Brake Switch 14 Drive Tire 15 Pump Idler Zerk 1 16 Deck Belt 17 Pump Belt 18 Blades 19 Hydraulic Oil Heat Exchanger
13. foot rest per the Maintenance Schedule Use SAE multi purpose grease 3 Grease the deck idler per the Maintenance Schedule Use SAE multi purpose grease 4 Grease the pump idler per the Maintenance Schedule Use SAE multi purpose grease 5 Grease the two deck pusher arm pivots per the Maintenance Schedule Use SAE multi purpose grease Electrical System Refer to Figure 4 2 NOTE The mower is shipped with negative ground cable disconnected from the battery The battery should be charged slowly 5 to 6 hours before connecting the ground cable to the battery and operating the mower The electrical system is 12 volt negative ground with the battery located under the seat Recommended battery is a maintenance free garden mower BCI group U1R with 225 or better cranking AMP rating Otherwise follow battery manufacturer s maintenance safety storing and charging specifications Negative Connection Battery and Hour Meter Figure 4 2 Ay warnine Shorts caused by battery terminals or metal tools touching metal tractor components can cause sparks Sparks can cause a battery gas explosion which will result in personal injury Prevent the battery terminals from touching any metal tractor parts when removing or installing the battery Do not allow metal tools to short between the battery terminals and metal tractor parts Ay warnine Avoid skin contact with battery acid Always wear eye protection when checking the b
14. is in the down OFF position Place control levers in the park brake position Disconnect negative battery cable Place the deck in the lowest position Remove the deck belt covers and floor panel Release the deck belt tension by pulling on the belt tension chain and sliding the chain out of the anchor bracket slot This will relieve the tension on the deck belt idler spring Refer to Figure 4 11 Pull the idler to the left of the machine to provide maximum belt clearance Remove the existing belt and replace with a new belt Route the new belt per Figure 4 11 Re tension the deck belt idler per the deck drive belt adjustment section on page 18 Re install the deck belt covers 10 Re attach the negative battery cable and floor panel Deck Belt Drive Layout 1 Spindle drive belt 2 Deck blade spindle pulley 3 Spindle belt tension idler 4 Spindle belt tension idler spring 9 0 at operation 5 Deck belt idler 6 Idler arm Deck Belt Drive Layout Figure 4 11 Integrated Pump Motor Drive Belt Refer to Figure 4 11 Figure 4 12 and Figure 4 13 Replace hydraulic pump motor drive belt as follows 1 Park the unit on a flat surface Stop the engine and remove the ignition key Make sure blade engagement switch is in the down OFF position Place control levers in the park brake position Disconnect negative battery cable 2 Place the deck in the lowest position 3 Refer F
15. of any defective part by Land Pride and the installation by the dealer of any such replacement part and does not cover common wear items such as blades belts tines etc Land Pride reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship This Warranty does not apply to any part or product which in Land Pride s judgment shall have been misused or damaged by accident or lack of normal maintenance or care or which has been repaired or altered in a way which adversely affects its performance or reliability or which has been used for a purpose for which the product is not designed Misuse also specifically includes failure to properly maintain oil levels grease points and driveline shafts Claims under this Warranty must be made to the dealer which originally sold the product and all warranty adjustments must be made through such dealer Any action for breach of warranty must be commenced within 25 months following delivery in non rented application and within 120 days following delivery in rented application This Warranty shall not be interpreted to render Land Pride liable for damages of any kind direct consequential or contingent to property Furthermore Land Pride shall not be liable for damages resulting from any cause beyond its reasonable control This Warranty does not extend to loss of crops any expense or loss for labor supplies rental machinery or for any other rea
16. the chain If not loosen the two nuts on the block holding the threaded rod until there is slack in the deck lift chain 21 Tighten the appropriate nut until the chain just becomes tight making sure that the deck stays tight against the 3 block 22 Tighten the other nut on the opposite side of the block and jam them tightly together against the block 23 Go to the left rear of the mower 24 Refer to Figure 3 17 Make sure that there is still slack in the chain If not loosen the two nuts on the block holding the threaded rod until there is slack in the deck lift chain 25 Tighten the appropriate nut until the chain just becomes tight 26 Tighten the other nut on the opposite side of the block and jam them tightly together against the block 27 Refer to Figure 3 20 Compress the deck lift assist springs so that there is 1 of space between the front nut and on the spring and the rear nut on the deck lift block Typical both sides 28 When completed all chains will be tight and deck cutting height will be set to the deck height indicator Deck Cutting Height Adjustment Refer to Figure 3 16 Deck height is adjustable from 1 1 2 to 4 1 2 in 1 4 increments The holes in the height adjusting bar are spaced at 1 2 intervals By turning the height adjusting stop around 1 4 increments can be attained due to the 1 4 plate that is part of the stop EXAMPLE When the height adjusting stop is plac
17. the fuel line between fuel tanks and engine fuel pump on the rear left side of the engine Replace filter annually or after every 100 hours of operation whichever occurs first For fuel filter removal refer to the engine owner s manual When replacing the fuel filter check the fuel line hoses for any cracks or leaks Replace as needed Refer to Figure 4 7 A fuel shut off valve is located on the outlet port of each fuel tank Close these valves turn clockwise to prevent fuel flow to the engine i Shut off Valve ee Fuel Shut Off Valve Figure 4 7 Draining the fuel tank 1 Park the unit on a flat surface Stop the engine and remove the ignition key Make sure blade engagement switch is in the down OFF position Place control levers in the park brake position Disconnect negative battery cable 2 Close the fuel shut off valve on the fuel tank to be drained 3 Trace the fuel line from the shut off valve to the Left Right Fuel Tank Valve Refer to Figure 2 3 on page 9 Loosen the hose clamp and remove the fuel line from the tee 4 Place the end of the fuel line into a gas can or a drain pan and open the fuel shut off valve to drain the fuel from the fuel tank 5 When fuel tank is drained re route the fuel line to the Left Right Fuel Tank Valve and attach to the valve Clamp fuel line to valve 6 Fill fuel tank with proper grade of gasoline and open shut off valve Changing fuel filters Refer to Figure 4 8A and
18. 3 Access to Engine amp Hydraulic Pumps Refer to Figure 4 5 The pump units are accessed under the seat platform Raise the seat platform by releasing the seat latch and tilting the seat platform up and forward about its hinged front A seat platform catch will prevent the seat from going all the way over Release the seat platform catch if more room under the seat is needed and pivot the seat further forward IMPORTANT Make certain to place the control arms in the park brake position and pivot the arm rests upward before placing the seat platform in the forward position Seat Platform Latch Seat Platform Latch Figure 4 4 Seat Platform Catch Access to Integrated Pump Motor Figure 4 5 Ay warnine Always wear adequate eye protection when servicing the hydraulic system and battery Hydraulic System Refer to Figure 4 6 Ay warnine Hydraulic oil escaping under pressure can penetrate skin Hydraulic oil may cause infection in a minor cut or opening in the skin If exposed to hydraulic fluid see a doctor at once Before applying pressure to hydraulic system make sure all connections are tight and all hoses and lines are in good condition To find a leak under pressure use a piece of cardboard or wood never use your hands Relieve all pressure in the system before disconnecting or working on hydraulic lines To relieve pressure lower all attachments and shut off engine 26 ZRP44 amp ZRP52 Zero Turning
19. 7 Control Lever Figure 3 3 To keep the pumps from bottoming out internally use the following procedure 1 To make the first adjustment the tractor engine must NOT be running 2 Check to make sure the control levers are against the stops before the pumps are bottomed outinternally To do this gently and slowly move the control levers forward and feel if there is some resistance on the pump lever before the control levers hit the stops Check one side at a time If you sense that the pump arms are stopping the forward motion of the control arms loosen the jam nut on the adjustable stop of the corresponding side and turn the stop set screw inward to stop the control levers slightly before the pump bottoms out Lock in place when the adjustment is correct by re tightening the jam nut 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 15 Table of Contents Section 3 Adjustments Land Pride 3 Do this for each side Refer to Figure 3 3 on page 15 To adjust the stops for driving straight when control levers are against the stops during operation 4 Determine which drive tire is rotating too fast when both control levers are against the stops Then stop the tractor and loosen the lock nut on the side which is rotating too fast and turn the stop set screw inward to stop the control lever sooner Tighten the lock nut on the stop and test again Repeat this procedure until unit drives straight NOTE S
20. Change oil and check for source of contamination High oil consumption Numerous See your dealer Mower jerky when starting or operates in one direction only Steering control linkage needs adjustment Hydraulic pump or wheel motors faulty Adjust linkage See your dealer Continued on next page 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 37 Table of Contents Land Pride Section 7 Troubleshooting Symptoms Probable Causes Suggested Remedies Hydraulic system operates hot Low hydraulic oil level Fill reservoir Oil in reservoir smells rancid Hydraulic pump faulty See your dealer Mower creeps when steering control Steering linkage needs adjustment Adjust linkage levers are in neutral Mower circles or veers in one Steering linkage needs adjustment Adjust linkage direction Wheel motors faulty See your dealer Hydraulic pump faulty See your dealer Mower creeps when parking brake Steering linkage needs adjustment Adjust steering linkage engaged Brakes need adjustment Adjust parking brakes Oil Light is on when engine is Engine oil level low Fill engine oil to required level running 38 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Table of Contents Section 8 Appendix Torque Values Chart for Common Bolt Sizes Bolt Head Identification Bolt Head Identification O en Inches Grade 8 Metric io m
21. Radius Mowers 356 117M 7 14 08 Land Pride Section 4 Maintenance and Lubrication Table of Contents IMPORTANT Never use hydraulic or automatic transmission fluid in this system use only motor oil as specified Remember dirt is the primary enemy of any hydraulic system IMPORTANT Each hydraulic pump is equipped with a bypass valve For additional information refer to Operating Section Moving Mower with Stalled Engine page 11 Refer to Figure 4 6 The 1 0 U S gallon 3 79 liter hydraulic reservoir is located in front of the engine and under the operator s platform i r Hydraulic Reservoir Filler Cap Hydraulic Reservoir Figure 4 6 Check oil level in hydraulic system after every 50 hours of operation or weekly whichever occurs first Check more often if system appears to be leaking or otherwise malfunctioning Fluid level should be 1 from top of reservoir Use only SAE 10W40 SG SF CC CD service motor oil Refer to Figure 4 6 Change hydraulic system filter element Land Pride P N 831 030C after first 50 hours of tractor operation then replace filter and oil in reservoir every 500 hours thereafter When changing hydraulic oil use 1 2 unit approximately 3 5 oz of Lubrizol additive Land Pride P N 821 041C This additive available from your Land Pride dealer will increase the performance life of the hydraulic system components The system filter is located to the right of the hydraulic reserv
22. Release the ignition key and push the choke to down off position Allow the engine to warm up momentarily If your mower has just been running and the engine is already warm using the choke is usually not necessary With the engine at half throttle reach forward and bring both steering levers equally together in the neutral position just in front of you It s now time to test your steering skills Gently push both steering levers equally forward The farther forward you push the levers the faster you will go Pull back equally and you will slow down coming to a stop when you reach the neutral position Now slowly pull the levers back toward your body past neutral position The mower will reverse direction and increase in speed as you pull further back If you push one lever forward and pull one lever back the mower will do a Zero turn in the direction of the steering lever closest to your body Now take a few moments in a safe area to practice steering your mower with the engine still at half throttle Gradually increase your throttle speed until you feel totally confident in your mower steering and handling ability It s now time to cut the grass Hopefully you have already removed any obstacles from the lawn that you do not want run over With your mower at half throttle place your right foot on the deck lift pedal and release and lower the deck to your preset cutting height With your right hand pull up on the cutting blade engage
23. Table of Contents Accu Z Razor Pro ZRP44 amp ZRP52 Zero Turning Radius Mowers x VA z A D a 5 eee Ne S NO YS IN PIP KAT N 356 117M Operator s Manual Operator s Manual entirely When his symbol the subsequent ns and warnings are serious follow xception Your life and the lives of o oo O03 n 7 14 08 D E x Qo 8 S N lt 2 S S S supplied y show optional equipment not r photo ma with standard unit Cove Land Pride Table of Contents Important Safety Information 1 Deck Leveling and Height Adjustment 19 Safety Labels 0000000 e ee eeee 3 Deck Level Adjustments 19 Introduction eceecccccuccuuus 6 Tire Inflation Chart 000 000 eee 19 Application 0 0 0 00 ccc eee eee 6 Deck Cutting Height Adjustment 21 Using This Manual 000000004 6 Anti Scalp Rollers 0000 eee 21 Terminology on nunana nanne 6 Section 4 Maintenance and Lubrication 22 BefNtUONS eea ee pe a ak eg 6 Maintenance 2h rei o ciate etree wen veea Meee eee 24 Owner Assistance 0 0c eee eens 6 Torque Values 000 c eee eee 24 Further Assistance 00005 6 TIES cue wake Mae io oS awawowlawuewewoules 24 Section 1 Assembly and Set Up 7 Tire Inflation Chart naana wih a ed aed OS 24 Co
24. Wheels 8 10 2 Park the unit on a flat surface 3 Refer to Figure 3 15 Raise deck and place 3 of blocking under all 4 corners of the deck This will set the cutting height at 3 1 4 NOTE Back of deck will automatically be set 1 4 higher eo Blocks Blocking up Deck Figure 3 15 Refer to Figure 3 16 Set cutting height at 3 1 4 on the height indicator by placing the height adjusting stop in the 3 hole and turning the height stop so that the flat side is against the stop handle 5 Clamp the height adjusting stop against the stop handle This will assure that the height will not move during the setting process Otherwise spring pressure from the deck lift springs will tend to pull the stop away from the handle Stop Height Adjusting Stop Handle Cutting Height Figure 3 16 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 19 Table of Contents Land Pride Section 3 Adjustments 6 Refer to Figure 3 17 amp Figure 3 18 Loosen all nuts on the deck lift threaded rods and the hardware on the adjuster on the right front until all the deck lift chains are loose and the deck is sitting tightly on all four blocks Foot Pedal Deck Lift threaded Rod 3 Deck Level Adjustment Foot Pedal Deck Level Adjustment Figure 3 19 Figure 3 17 8 Start the leveling process on the left front of the mower 9 Refer to Figure 3 20 Set the amount of threads protrudin
25. ade type Seat Neutral Kawasaki engine 5 Amp blade type Honda engine 10 Amp blade type Before attempting any failure diagnosis of the electrical system use a test light or voltmeter to check the battery voltage If the battery voltage is satisfactory check the cleanliness and tightness of the terminals and ground connections A general understanding of electrical servicing and use of basic test equipment is necessary for troubleshooting and repair Major overhaul or repair of the starting motor or alternator should be performed by trained technicians only 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 25 Section 4 Maintenance and Lubrication Land Pride Burnishing the Electric Clutch Refer to Figure 4 3 Ay warnine Figure 4 3WARNING To insure maximum performance and life it is necessary to burnish the clutch Burnishing the electric clutch Fig 4 4 will develop better contact between the armature and rotor helping to develop higher torque capabilities without slipping The warranty on the new clutch will be voided if it is not burnished properly Use the following procedure to burnish the clutch 1 Check the air gap between armature and rotor Gap should be 012 to 024 2 Cycle the clutch on and off 10 times 15 seconds on and 15 seconds off with the engine operating at half throttles approximately 1500 rpm EL LES Electric Clutch x t Electric Clutch Figure 4
26. ades ia 19074 Resharpening Pattern Do not sharpen to original pattern below It is easier to get a straight cutting edge following the resharpening pattern shown above riginal Edge 19075 Blade Resharpening Figure 4 16 Ay warnine When mounting blades rotate them after installation to ensure blade tips do not touch each other or sides of the mower Ay warnine Failure to correctly torque the bolt may result in the loss of the blade which can cause serious injury STORAGE When storing the unit at the end of the mowing season the following steps should be taken to ensure readiness for the next mowing season 1 Remove all grass dirt and trash Clean and touch up all scrapes with Land Pride spray paint 2 Clean paper air filter Replace if necessary Wash and re oil foam pre cleaner 3 Check thoroughly for any worn or damaged parts that need replacing and order them from your dealer 4 Thoroughly lubricate machine according to lubrication instructions 5 Check hydraulic oil level Add oil if necessary Change oil and filter if not done in last 500 hours Lubrizol additive is required Refer to Maintenance section 6 Block mower up so weight is off tires NOTE Do not deflate tires 7 Protect battery from freezing temperatures Occasionally recharging battery during storage will extend battery life 8 Perform separate engine preparation as listed below
27. ades sharp Many problems with incorrect cutting patterns are due to dull blades or blades which have been sharpened incorrectly Information on sharpening blades is listed in this manual s maintenance section In addition most communities have individuals or companies which specialize in sharpening mower blades Blade sharpness should be checked daily Often professional mowing companies have an additional set of blades and change blades twice a day once in the morning and again at noon Use high blade speed Your Razor Pro is designed to operate at full throttle The throttle setting directly controls blade speed The highest blade speed generally gives the best cut Direct grass discharge away from unmown area Refer to Figure 2 9 on page 13 Select a mowing pattern that directs grass discharge away from uncut grass Generally this means using a pattern utilizing left turns because grass side discharge is to the right Grass discharged onto an unmowed area will be mowed twice Mowing grass twice puts an unnecessary load on the mower and reduces mowing efficiency 12 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Section 2 Operating Table of Contents Discharge Chute Discharge Chute Figure 2 9 Ay warnina Never direct discharge of material from mower deck towards bystanders Ay warnine Never operate the mower deck with discharge chute removed or in raised position Ay war
28. amp ZRP52 Zero Turning Radius Mowers 356 117M 39 Table of Contents Land Pride Section 8 Appendix NOTES 40 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Table of Contents Section 8 Appendix Warranty Land Pride warrants to the original purchaser that this Land Pride product will be free from defects in material and workmanship beginning on the date of purchase by the end user according to the following schedule when used as intended and under normal service and conditions for personal use Overall unit 2 years or 1200 hours limited warranty on parts and labor whichever comes first Engine 2 years limited warranty through Engine manufacturer Hydraulic Wheel Motors and Pumps 2 years on Parts and Labor Front Edge of Mower Deck Limited warranty against all defects in the deck which results in the front edge of the deck being bent into the blades for the entire length of ownership by the original purchaser Frame Frame breakage through the entire length of ownership by the original purchaser Blade Spindle 3 years or 1200 hours Parts and Labor Front Gauge Wheel Yoke Bearings 3 years or 1200 hours Parts and Labor Battery 1 year limited warranty Rental Units Limited warranty on all materials and workmanship for a period of 90 days Belts blades and tires are considered wear items Filters and Plugs are considered maintenance items This Warranty is limited to the replacement
29. ands 2 Position the control levers in the neutral position Disengage the blades 3 Start the engine and observe which way the wheels are rotating 4 lfwheel s are rotating forward loosen the jam nuts on the pump linkage rods and rotate the rod to lengthen the steering control linkage until the wheel s come to a stop Repeat for the opposite side if necessary NOTE The left linkage controls the right hydraulic pump and the right linkage controls the left hydraulic pump 5 If wheel s are rotating in reverse then loosen the jam nuts on the pump linkage rods and rotate the rod to shorten the steering control linkage until the wheel s come to a stop Repeat for the opposite side if necessary 6 When both wheels remain in neutral tighten the jam nuts to lock the turnbuckle in place 7 Test again by moving the control levers forward and backward before returning them to the neutral position If the tires are in neutral the unit is now ready for operation 8 After adjusting for neutral it may be necessary to readjust the steering dampener and or the control lever stop Fig 5 3 or Fig 5 4 Control lever stops Refer to Figure 3 3 The control lever stops are designed to do two things First and most important they must keep the pumps from bottoming out internally Secondly the stops may be adjusted to help drive straight when the control levers are pushed forward against the stops Jam Nut 2106
30. arts go to your Land Pride Dealer IMPORTANT For parts and service for your engine contact your nearest dealer or Call Customer Service Hotline Honda Engine Information Service Manual P N 612ZJ410Z Owner s Manual P N 31ZJ4620 Service Hotline 1 770 497 6400 Kawasaki Engine Information Service Manual P N 99924 2045 02 Owner s Manual P N 99920 2145 02 Service Hotline 1 800 433 5640 Serial Number Plate Refer to the Figure 1 for the location of your serial number i Serial Number Location Figure 1 Further Assistance Your dealer wants you to be satisfied with your new mower If for any reason you do not understand any part of this manual or are not satisfied with the service received the following actions are suggested 1 Discuss the matter with your dealership service manager making sure he is aware of any problems you may have and that he has had the opportunity to assist you 2 If you are still not satisfied seek out the owner or general manager of the dealership explain the problem and request assistance 3 For further assistance write or E mail to Land Pride Service Department P O Box 5060 Salina KS 674022 5060 E mail address lIpservicedept landpride com 6 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Section 1 Assembly and Set Up Table of Contents Control Lever amp Seat Assembly Refer to Figure 1 1 The seat 1 is shipped l
31. attery acid can cause serious injury to skin and eyes If contact occurs flush area with clean water and call physician immediately Acid will also damage clothing Do not allow open flame near the battery when charging Hydrogen gas forms inside the battery This gas is both toxic and flammable and may cause an explosion if exposed to flame Always remove the negative ground first and replace it last Do not overfill battery Electrolyte may overflow and damage paint wiring or structure When cleaning the battery use soap and water Be careful not to get soap and water into the battery Use soda mixed in water to clean corrosion off the terminals Ay warnine Incorrect battery cable routing can cause damage to the tractor and battery cables This can cause sparks which can cause a battery gas explosion which will result in personal injury Always disconnect the negative black battery cable before disconnecting the positive red cable Always connect the positive red battery cable before connecting the negative black cable Common circuit failures are usually caused by shorting corroded or dirty terminals loose connections defective wire insulation or broken wires Switches solenoids and ignition components may also fail causing a shorted or open circuit The electrical system is protected by fuses located on the right fuel tank instrument panel The fuses are as follows Main 20 Amp blade type Clutch Aux 10 Amp bl
32. e mower incorporates a separate seat switch which will stop the engine whenever the operator is unseated while the mower is moving or the blades are engaged This safety feature is designed to prevent runaway or accidental entanglement Inspect the system as follows 1 The operator must be on the seat when testing the seat switch 2 Set both control levers in the park brake position 3 Start the engine and allow it to warm up to operating temperature 4 Aperson should be able to slowly raise off the seat without the engine stopping if the blade engagement switch is down and the control levers are in the park brake position 5 The engine should stop within two seconds if a person raises slowly off the seat and either the blade engagement switch is up or the control levers are in neutral position 6 Check the function of the seat switch If the engine fails to stop when the blade engagement switch is up or if one or both of the control levers are in and the operator is off the seat Replace the seat switch If the seat switch is not operating properly i e switch is not opening and or closing If the problem cannot be located contact your Land Pride Dealer Ay warnine The safety interlock system should always function per steps 4 and 5 If it does not function properly it should be corrected immediately Do not operate machine without a properly functioning seat safety switch Engine Starting The Razor Pro safety s
33. e running or while engine is hot Clean up any gasoline spills Allow engine to cool before storing machine inside a building Keep fuel away from open flame or spark and store machine away from open flame or spark if there is fuel in the tank Use extra caution when handling gasoline and other fuels They are flammable and vapors are explosive A fire or explosion from gasoline can burn you and others and can damage property Refuel outdoors preferably or in well ventilated areas Never attempt to start engine when there is a strong odor of gasoline fumes present Locate and correct cause Store gasoline in an approved container and keep it out of the reach of children Never buy more than a 30 day supply of gasoline Do not fill gasoline containers inside a vehicle or on a truck or trailer as interior carpets or plastic truck bed liners may insulate the container and slow the loss of any static charge When practical remove equipment from the truck or trailer and refuel the equipment with its wheels on the ground If this is not possible then refuel the equipment on the truck or trailer using a portable container and not a gasoline dispenser nozzle If a gasoline dispenser nozzle must be used keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete Ay warnine Gasoline is harmful or fatal if swallowed Long term exposure to vapors can cause serious injury and illness Avoid p
34. ecified in the engine operator s manual Please refer to this manual for engine servicing lubricating oil levels with quality and viscosity recommendations bolt torques etc The engine warranty is backed by the engine manufacturer Special attention should be paid to applicable data which will not be duplicated here Belt Replacement Refer to Figure 4 11 and Figure 4 12 Replace belts which show signs of severe cuts tears excessive weather checking and cracking or burns caused by slipping Slight raveling of belt covering does not indicate failure trim ravelings with a sharp knife Inspect the belt pulley grooves and flanges for wear A new belt or one in good condition should never run against the bottom of the groove Replace the pulley when this is the case otherwise belt will lose power and slip excessively Never pry a belt to get it on a pulley as this will cut or damage the fibers of the belt covering Keep oil and grease away from belts and never use belt dressings Any of these will destroy the belt composition in a very short time Ay warnine If the pump belt fails loss of control may occur when operating on a Slope 30 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Table of Contents Section 4 Maintenance and Lubrication Deck Drive Belt 1 p 9 Park the unit on a flat surface Stop the engine and remove the ignition key Make sure blade engagement switch
35. ecting the problem as quickly as possible is the best insurance Ay warnine Keep your machine clean and remove heavy deposits of trash and clippings They can cause engine fires and hydraulic overheating as well as excessive belt wear Clear away heavy build up of grease oil and dirt especially in the area of oil fuel and engine combustion air minute dust particles are abrasive to close tolerance engine and hydraulic assemblies Some repairs require the assistance of a trained service mechanic and should not be attempted by unskilled personnel Consult your Land Pride service center when assistance is needed Torque Values Ay warnine Particular attention must be given to tightening the drive wheel lug nuts and blade spindle bolts Failure to correctly torque these items may result in the loss of a wheel or blade which can cause serious damage or personal injury Torque Values FT Ibs N m Wheel lug nuts 65 75 88 14 101 7 Wheel motor nut 290 310 393 2 420 4 Blade spindle bolts top 118 and bottom 160 01 It is recommended that the following be checked after the first 2 hours of initial operation and every 50 hours following removal for repair or replacement e Wheel lug nuts e Wheel motor nut e Blade spindle bolts top and bottom e For engine torque values see engine owner s manual e For all other torques refer to Torque Values Chart for Common Bolt Sizes on page 39 S
36. ed in the 1 1 2 hole with the 1 4 plate facing to the front of the unit the cutting height is at 1 1 2 When the height adjusting stop is placed in the 1 1 2 hole with the 1 4 plate on the operator s side of the hole the cutting height is at 1 3 4 When the height adjusting stop is placed in one of the holes with the 1 4 plate on the operator s side of the hole the deck height will be set at one of the following 1 3 4 2 1 4 2 3 4 3 1 4 3 3 4 or 4 1 4 When the height adjusting stop is placed in one of the holes with the 1 4 plate facing to the front of the unit the deck height will be set at one of the following 1 1 2 2 2 1 2 3 3 1 2 4 or 4 1 2 The notch located at the rear of the right height adjusting bar 4 1 2 height is to used when the deck is placed in the transport mode Anti Scalp Rollers Refer to Refer to Figure 3 21 Anti scalp rollers are standard on the Razor Pro These anti scalp rollers are designed to minimize scalping when mowing on rough uneven terrain After setting the cutting height adjust the front anti scalp rollers so they extend below the deck but do not contact the ground They should always be at least 1 4 to 3 4 below the deck With the unit sitting on a flat level surface the front wheel position can be adjusted up or down as needed from 3 4 to 1 3 4 below the blade surface Move the front wheels up or
37. eed forward reverse brake and turns Steering Turning Radius True zero degree Turns within its own length with counter rotating independent drive wheels Brake Service Hydrostatic dynamic braking Parking Automotive style drum brakes Integral park brakes are automatically engaged When steering levers are placed in neutral Mower Drive Single V belt with electric clutch and spring tension idler pulley Safety Features Operator presence system connected to deck and drive clutches Stabilizer rollers rear of tractor Seat Mainframe Construction Drive Motor Mount Molded viny seat with armrests and fore and aft adjustment Optional deluxe cushion seat 1 1 2 x 2 x 1 8 rectangular steel tubing 179 welded steel Caster Wheels Front Caster Forks Deck Thickness Mounted with roller bearings on each wheel 3 8 steel 11 Gauge with 11 gauge doubler deck plate Deck Trim Edges Deck Lift Hand Operated Controls 1 x 3 8 Foot operated deck height adjustment Pin for setting height transport position choke throttle ignition switch electric mower clutch and Integrated parking brakes Indicators Cup Holder Cutting Heights Hour meter engine warning light Two cup holders molded into the left side fuel tank Accommodates nearly any cup size including Big Gulp Foot operated deck height adjustment Pin for setting height transport position Height adjustment in 1 4
38. et Installed spring length should be 9 0 3 22 8 cm 76 cm originally with adjustments of 60 15 2 mm per chain link sma Drive Belt Adjustment Figure 3 13 Actual body and frame colors may be different than what is represented in the picture 18 2ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Section 3 Adjustments Table of Contents IMPORTANT Refer to Figure 3 14 Do not over tension the spring to compensate for a badly worn belt or pulley Maximum Spring Extension o Normal Spring Length 7 Spring Tension Figure 3 14 Engine RPM Setting The Razor Pro is designed so that the engine will run at 3600 rpm static pump load only At this speed the hydraulic pumps are running at their maximum rated speed Deck Leveling and Height Adjustment The mower deck has three areas that may need to be checked and adjusted periodically Before considering any mower deck leveling adjustments check that the tire air pressure is within the specified range A warnine Stop engine Make sure deck clutch switch is in the down OFF position Place control levers in the brake position before leaving machine Deck Level Adjustments Leveling the deck must be done in the following manner and order 1 Check tire pressures to make certain they are properly inflated before starting to level deck Tire Inflation Chart Tire Inflation PSI Drive Wheels 8 10 Gauge
39. formation A Work in aclean dry area A Do not grease or oil while in operation A Inspect all parts Make sure parts are in good condition amp installed properly A Remove build up of grease oil or debris A Remove all tools and unused parts before operation k y Le Safety at All Times Thoroughly read and understand the instructions given in this manual before operation Refer to the Safety Label section read all instructions noted on them A Operator should be familiar with all functions of the unit A Operate mower from the driver s seat only A Do not leave mower unattended with engine running A Dismounting from a moving mower could cause serious injury or death A Keep hands feet and clothing away from power driven parts A Wear snug fitting clothing to avoid entanglement with moving parts A Make sure all persons are clear of working area 2 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Important Safety Information These are common practices that may or may not be applicable to the products described in this manual Table of Contents Prepare for Emergencies A Be prepared if a fire starts A Keep a first aid kit and fire extinguisher handy A Keep emergency numbers for doctor ambulance hospital and fire department near phone 5 Wear Protective Equipment A Protective clo
40. g on the deck lift rod from the lift block at approximately 1 5 16 Bolt Jam Nut Adjuster S A E Deck Lift Assist Hardware f Springs Deck Level Adjustment Left je ee Threads Figure 3 18 gu 7 Refer to Figure 3 19 Loosen the two nuts on the front 10 Jam both nuts against the lift block of height indicator so that the foot pedal is free 11 Push or pull on the deck lift foot pedal until the chain on the left front just becomes tight making sure that the deck stays tight against the 3 block 20 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Section 3 Adjustments Table of Contents 12 Refer to Figure 3 19 While keeping the chain tight tighten the nuts against the deck lift block on the height indicator rod 13 Go to the right front of the mower 14 Refer to Figure 3 18 Loosen the 5 16 jam nut on the adjuster lift chain and back the adjuster bolt out to allow the adjuster to move up and down freely 15 Be sure that adjuster is free to move up and down 16 Tighten the adjuster bolt until the chain just becomes tight making sure that the deck stays tight against the 3 block 17 Refer to Figure 3 18 Tighten the adjuster bolt jam nut to prevent the adjuster bolt from moving 18 Tighten the hardware holding the chain and adjuster onto the deck lift arm 19 Go to the right rear of the mower 20 Refer to Figure 3 17 Make sure that there is still slack in
41. idth Height Length 44 53 40 72 985 Weight Drive Tires Front Tires bs 1000 20 x 10 00 10 turf tread 13 x 5 00 6 no tread Starter 12 volt 8 KW solenoid shift positive engagement Ignition Charging System Electronic 12 volt 15 amp Governor Fuel Fuel Capacities Mechanical Unleaded gasoline with octane rating of 87 or higher 12 2 US GAL Traction Drive Type Dual Hydrostatic Transmission Hydraulic Drive Oil 10W40 Motor oil Hydraulic Oil Capacity 2 US GAL 7 57 L Hydraulic Pumps Two variable displacement axial piston type Hydraulic Lines Stainless steel high pressure lines with Parker Seal Lok O Ring Face Seal Fittings Hydraulic Filter 40m icron Replaceable spin on type Part No 831 030C Final Drive White CE 12 direct drive high torque wheel motors for each drive wheel 34 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Table of Contents Section 5 Specifications and Capacities ZRP44 amp ZRP52 Razor Pro Riding Mowers General Specifications ZRP44 ZRP52 Hydraulic Pump Drive V belt drive from engine crankshaft Ground Speed Steering Type Forward Transport 0 13 MPH 0 20 92 KPH Forward Mowing 0 10 MPH 0 16 09 KPH Reverse Movement 0 7 MPH 0 11 27 KPH Twin lever steering provides independent control of each drive wheel Twin Lever Steering Controls Sp
42. igure 3 13 on page 18 and Figure 4 110n this page Release the deck belt tension by pulling on the belt tension chain and sliding the chain out of the anchor bracket slot 4 Remove deck drive belt from the electric clutch pulley mounted to the engine This belt does not need to be removed from any of the other pulleys 5 Release the tension from the integrated pump motor belt by pulling on the idler pulley extension spring carefully until the belt can be slide over the idler pulley Use caution when releasing the idler pulley as there is still tension on it and it will snap back into position Pump Belt Layout 1 Pump belt 2 Engine pulley 3 Pump idler pulley 4 Pump idler arm 5 Pump pulley 6 Electric Deck Clutch 7 Pump idler spring Mower Viewed from Bottom Deck Figure 4 12 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 31 Table of Contents Section 4 Maintenance and Lubrication Land Pride 6 Slide the belt off and above the engine pulley to allow the belt to be removed from the pump motor pulleys Hydraulic Drive Pulley Clutch Drive Pump Motor Belt Removal Figure 4 13 7 Slide the belt over and off the integrated pump motor pulleys 8 Remove the belt from above the engine pulley 9 Install new belt by sliding it up and over the engine pulley Make certain it is not in the pulley groove at this time but is above the pulley 10 Slide the belt over the integrated pump
43. ince this is a hydrostatic drive variables such as temperature of oil efficiency of pumps and motors tire pressure etc may effect the consistency of the ability to rely on the stops to drive straight without the operator making minor steering adjustments with the control arms Steering Dampener Refer to Figure 3 4 The steering dampeners one for each control lever are spring loaded to return the control levers to neutral position from reverse position This gives the operator a sense of neutral during operation Set the steering dampeners in the correct operating position as follows 1 Place control lever in the neutral position 2 Loosen steering dampener s front ball stud 3 Pull the dampener spring housing to the front past the point that the internal spring is engaged 4 Release the dampener spring housing and allow the internal spring to bring the housing back to the neutral position 5 Tighten the nut on the steering dampener s front ball stud 6 To check move the control lever to the reverse position and release The control lever should return to the neutral position If not repeat steps 1 through 6 Steering Dampener Figure 3 4 NOTE The dampener must not bottom out when the pump lever is fully stroked in either direction Control Lever Adjustment Refer to Figure 3 5 The control levers may be adjusted vertically and pivoted forward or backward for operator comfort Adjust the contr
44. increments from 1 1 2 to 4 1 2 Mowing Blades Blade Tip Speed Blade Drive Heavy duty heat treated high lift steel blades 20 x 2 1 2 x 15 7 20 x 2 1 2 x 18 3 16 100 FPM 18 300 FPM Single V belt drive to all three spindles with spring tension idler pulleys and electric clutch Spindles Flotation ACCESSORIES Mulch Kit Machine aluminum housing 1 diameter high carbon steel shafts and sealed ball bearings Suspended mower floats on four spring assisted chains 4 anti scalp wheels are standard Recycles clippings under deck allowing clippings to be cut and recut then discharged down into the grass Reduces handling of clippings improves appearance and recycles nutrients back to the soil 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 35 Table of Contents Section 6 Features and Benefits ZRP44 amp ZRP52 Razor Pro Riding Mowers Features Benefits 44 or 52 Cutting width Sized and priced right for residential owners Mid mount deck design Mid mount design puts the deck closer to the operator s line of sight for a more efficient and precise operation Compact size Drive tire stance Steering levers Reinforced Deck Enhances mowing maneuverability as well as fitting on trailers or storing more efficiently Narrow width ZRP44 44 ZRP52 53 allows for tight turns in corners yet gives a very stable platform for the
45. ion of steering control levers Stop engine and check for oil leaks loose fittings and so forth 4 Tighten any bolts that have loosened and make sure all hair pins cotter pins and clevis pins are in place 5 Install all safety shields and review safety precautions listed in this manual Check and inflate tires to 8 10 psi Reconnect spark plug leads to spark plug N amp 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 33 Table of Contents Section 5 Specifications and Capacities CellHeadCol Land Pride ZRP44 amp ZRP52 Razor Pro Riding Mowers Engine Specifications ZRP44 ZRP52 ZRP52 Engine Type Kawasaki Kawasaki Honda Horsepower 19 23 24 2 No of Cylinders 2 2 Displacement 41 2 cu in 675cc 4 1 2 cu in 675cc 40 9 cu in 670cc Compression 8 1 1 8 Ratio Max Torque 37 0 FT LBS 2400 RPM 3 1 1 8 3 1 7 0 FT LBS 2400 RPM 37 5 FT LBS 2500 RPM Oil Capacity 2 US quarts 2 US quarts 1 8 US quarts Oil Filter Fuel Filter Part No 831 034C Replaceable Automotive Type Land Pride Part No Part No 831 038C Replaceable Automotive Type 831 031C Land Pride Part No 831 035C Cooling Air cooled Fly wheel fan Air cooled Fly wheel fan with oil cooler ZRP44 amp ZRP52 Razor Pro Riding Mowers General Specifications o ZAP4A ZAP52 Width of Cut 44 Trim Capacity left side pA ooo S O Overall width Tire to tire w
46. itch Figure 2 3 Blade Engagement Switch Refer to Figure 2 2 The Blade engagement switch engages the blade clutch which engages deck blades Pull the switch up to engage and push switch down to disengage the blades IMPORTANT Never engage blades with engine running at high rpm or when the deck is under load Clutch belts or deck could be damaged Control Levers Refer to Figure 2 4 These levers control the mower s speed direction neutral lock and park brake Levers are used to steer accelerate decelerate and change direction The mower will not move when the engine is on drive pumps are operating and the control levers are in the park brake position out Figure 2 5 Control Levers Figure 2 4 The Parking Brakes are applied by moving the control levers from the Neutral Position Figure 2 4 to an outward position Figure 2 5 Each rear wheel brake operates independently of the other Ay warnine In the event of a system failure while mowing engage both parking brakes to stop or slow mower Ay warnine The parking brake is not designed to hold the mower on steep Slopes Control Levers in Parking Brake Position Figure 2 5 Deck Lift Pedal Refer to Figure 2 6 The
47. king brakes are engaged when steering levers are placed in neutral does not require a separate operation to place in neutral One less thing to look for if mower does not start Drive Each rear drive wheel has an integrated hydrostatic pump amp drive motor Electric start Integrated fan blades Easily starts with the turn of a key Pumps stay cool 12 2 gallon fuel capacity Less down time Easy engine maintenance Engine is mounted so that all of the maintenance items can be serviced from the rear of the mower vs the side Seat Options Adjustable molded seat incorporates a high back and armrests to give adequate comfort for the long jobs or Deluxe Cushion seat for additional suspension over rough terrain Molded in cup holders Easy to reach cup holders fit a wide variety of cups and are in easy access to driver 36 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M Land Pride 7 14 08 Land Pride Section 7 Troubleshooting Table of Contents The majority of operating problems that occur with a system can be traced to improper adjustments or delayed service A consistently applied preventative maintenance program as outlined in the maintenance section of this manual will prevent many problems The following chart is designed to help you locate a problem by suggesting probable causes and the recommended solutions Symptoms Probable Causes Suggested Remedies
48. l lug nuts and blade spindle nuts Failure to correctly torque these items may result in the loss of a wheel or blade which can cause serious damage or personal injury Torque Values Wheel lug nuts 65 75 88 14 101 7 Wheel motor nut 290 310 393 2 420 4 Blade spindle bolts top 118 160 01 and bottom It is recommended that these be checked after the first 2 hours of initial operation and every 50 hours following removal for repair or replacement For all other torques refer to Torque Values Chart page 39 For engine torque values see engine owner s manual Tires It is important for level mowing that the tires have the same amount of air pressure Tire Inflation Chart Tire Inflation PSI Drive Wheels 8 12 Gauge Wheels 8 12 Solid fill tires are not to be used on the Razor Pro mowers 24 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Section 4 Maintenance and Lubrication Table of Contents Hour Meter Refer to Figure 4 2 To recognize when your machine needs servicing check the hour meter and the maintenance schedule The hour meter shows the number of hours the engine has run and the maintenance schedule lists the service intervals Lubrication 1 Grease the front gauge wheel bearings per the Maintenance Schedule Use SAE multi purpose grease 2 Grease the four deck lift pivots located to the side of the operator s
49. ld follow on a routine basis Remain alert for unusual noises they could be signaling a problem Visually inspect the machine for any abnormal wear or damage A good time to detect potential problems is while performing scheduled maintenance service Correcting the problem as quickly as possible is the best insurance Ay warnine Keep your machine clean and remove any deposits of trash and clippings which can cause engine fires and hydraulic overheating as well as excessive belt wear Clear away heavy build up of grease oil and dirt especially in the engine and under the seat platform area minute dust particles are abrasive to close tolerance engine and hydraulic assemblies Daily inspect mower for grass clippings and wire and string tangles The underside of the mower deck will collect a build up of grass clippings and dirt especially when grass is wet or has high moisture content This build up will harden restricting blade and air movement and will probably show a poorer quality of cutting Therefore it should be removed routinely To do this it will be necessary to raise and block the deck in the full up position and scrape the build up from underneath Some repairs require the assistance of a trained service mechanic and should not be attempted by unskilled personnel Consult your Land Pride dealer when assistance is needed Torque Values Ay warnine Particular attention must be given to tightening the drive whee
50. ment knob and increase the engine speed to full throttle You may now begin mowing When you are done mowing or just want to take a break make sure you do all of the following Park on level ground disengage the cutting blade throttle back leave the steering levers in wide open parking brake position turn the engine off remove the key and step carefully off the front of the machine 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 13 Table of Contents Section 3 Adjustments Land Pride Introduction Ay warnine Unless specifically required DO NOT have engine running when servicing or making adjustments to the mower Place control levers in the park brake position and remove ignition switch key Repairs or maintenance requiring engine power should be performed by trained personnel only To prevent carbon monoxide poisoning be sure proper ventilation is available when engine must be operated in an enclosed area Read and observe safety warnings in front of manual Your Razor Pro was adjusted before it left the factory and was checked during pre delivery set up However after start up and continued use a certain amount of break in wear will cause some adjustments to change Remain alert for unusual noises they could be signaling a problem Visually inspect the machine for any abnormal wear or damage A good time to detect potential problems is while performing scheduled maintenance service Corr
51. motor pulleys 11 Slide the belt onto the engine pulley 12 Pullthe spring tensioned idler pulley over and slide the belt onto it Make certain to keep fingers from getting between the belt and the pulley when the pulley is released and tension is re established 13 Re install the deck drive belt on the engine electric clutch pulley and make sure it is routed properly on all of the deck pulleys 14 Re tension the deck belt idler per the Deck Drive Belt Adjustment instructions on page 18 15 Re attach the negative battery cable Mower Blade Maintenance Refer to Figure 4 14 and Figure 4 15 on page 32 Ay warnine Never attempt to straighten a bent blade by heating or weld a cracked or broken blade as the blade may break and cause serious injury A DANGER Never work with blades while engine is running or blade engagement is engaged Always place blade engagement switch in the down Off position place control levers in park position and turn engine off Block up mower when you must work under it Wear gloves when handling blades Always check for blade damage if mower strikes rock branch or other foreign object during mowing Check the mower blades daily they are the key to power efficiency and well groomed turf Keep them sharp a dull blade will tear rather than cut the grass leaving a brown ragged top on the grass within a few hours A dull blade also requires more power from the engine Replace any blade which i
52. nce and Lubrication Land Pride Maintenance Ay warnine Unless specifically required DO NOT have engine running when servicing or making adjustments to mower Place control levers in the neutral position disengage blade engagement and remove ignition switch key Repairs or maintenance requiring engine power should be performed by trained personnel only To prevent carbon monoxide poisoning be sure proper ventilation is available when engine must be operated in an enclosed area Read and observe safety warnings in front of manual Ay DANGER Before working on or under the deck make certain engine cannot be accidentally started Shut engine off and remove ignition switch key for maximum safety Repairs or maintenance requiring engine power should be performed by trained personnel only A DANGER Exercise caution when working under the deck as the mower blades are extremely sharp Wearing gloves is advisable when working around or with the blades Ay warnine Except when changing or checking belt always keep belt covers on mower for safety as well as cleanliness Ay warnine When possible clean under mower using a stick or similar instrument making sure that no part of the body especially arms and hands are under mower Regular maintenance is the best prevention for costly downtime or expensive premature repair The following pages contain suggested maintenance information and schedules which the operator shou
53. nine Always check area to be mowed for rocks and other debris before mowing Mower Deck Operation A DANGER Never attempt to make any adjustments to the mower deck while the engine is running or when the blades are engaged Mower blades cannot be seen and are located very close to deck housing Fingers and toes can be cut off instantly With the engine running engage the blades Refer to Figure 2 10 and advance engine throttle to full rpm NOTE Engaging the blades at high engine rpm or when under heavy load in tall grass for example can cause belts to slip resulting in premature wear or possible damage p EN AS Blade Engagement Switch Blade Engagement Switch Figure 2 10 Operating Instructions After thoroughly familiarizing yourself with the Operator s Manual and completing the Operator s Checklist you are almost ready to begin mowing Approach the mower from the front Spread the steering levers fully apart if they aren t already in the wide open parking brake position Taking care not to step on either side of the mower deck step up on the operators platform and comfortably seat yourself With both steering levers still wide apart now reach for the throttle and choke control to your right side Position the throttle control at half throttle and pull the choke to the up on position Insert your ignition key and rotate the ignition key clockwise until you hear the engine begin to start
54. ntrol Lever amp Seat Assembly 7 Bois ees eee eee Heli ecole et eee ee ee eee etree eee eee one Operating E tae a gle eae 7 Electrical System i cucnene ooo se so eu eur ene 25 Ignition Switch 0 eceeceeeeeeeeee 8 Burnishing the Electric Clutch 26 Throttle Control d eee 8 Access to Engine amp Hydraulic Pumps 26 Choke Control cc cul wives cel fee tes oa ean 8 Hydraulic System 0 0 0 0c cee 26 Left Right Fuel Tank Valve 0 20 00 g FHGLSYSION oyang A Blade Engagement Switch 9 Draining ine wal TAN abate cha a 28 Control Levers aana aaa aAA adsense 9 Changing fuel filters 02 6 2 see eee 28 Deck Lift Pedal sock ce secs ame merce nanan 9 Engine Oil and Filter 005 29 Instrumentation 000002 eee 10 Engine Air Filter SAE NE AS SN SANG gs Neg Gg 29 Oil Pressure Light 000000s 10 Over Servicing Payee ter patie Selene pee Se panes 29 Electronic Hour Meter 10 Improper Misi ananon a RM ye a en eng ee 30 Safety Start Interlock System 10 Damaged iter Seals Of CANNET ns sste ae 30 ENGINE StAntinG veivey wevev eek a MENEK E KEREKERE 10 Incorrect Air Filter Element Fee Nie a ie Cena 30 Moving Mower with Stalled Engine 11 Engine Air Filter Service Procedure 30 Driving the Mower 0 0ececeeeeeee 11 General Engine Maintenance 30 S
55. oir A standard oil filter wrench is used to change filter threads are right handed Use Land Pride approved filter element P N 831 030C only IMPORTANT Prefill the filter element with clean oil before installing to prevent drawing air into the system pump Replace filter element as follows 1 Fill the filter element with clean system oil Smear a light coating of oil on upper surface of rubber seal 2 Install the filter element on base Tighten the oil filter by hand until the filter seal makes contact with the filter head then tighten an additional 3 4 turn with a an oil filter wrench DO NOT OVERTIGHTEN 3 Start tractor engine and let run at approximately 2 3 throttle for a few minutes to work any trapped air out of the system before engaging the steering control lever 4 Stop the engine and check the filter and connections for leaks 5 Check the hydraulic reservoir for specified oil level Add clean oil as necessary Clean or replace hydraulic reservoir cap annually Cap may be cleaned by dipping in or flushing with cleaning solvent Follow manufacturer s instructions and warnings for application of solvent type selected NOTE The hydraulic pumps are equipped with bypass valves Refer to Moving Mower with Stalled Engine on page 11 for more information Fuel System Refer to Figure 4 7 A DANGER Observe usual fuel handling precautions do not smoke while refueling do not fill tank with engin
56. ol levers vertically by removing the capscrews flat washers and locknuts that attach the upper control levers to the lower control levers Reposition the upper control levers to a height that fits the operator s personal preference Reassemble the capscrews flat washers and locknuts in the same order they were removed without tightening them Pivot the upper control levers forward or backward to again fit the operator s personal preference Verify that the control levers align with each other when in the neutral position and tighten the locknuts to correct torque Upper Control Lever Capscrews with Flat Washers Lower Control Lever Control Lever Adjustment Figure 3 5 Park Brake Adjustment Occasionally check the park brakes and adjustment using the following method 1 Position the control levers in the neutral position Disengage the deck clutch Ay warnine Make certain machine is secure when it is raised and placed on the jack stands The jack stands should not allow the machine to move when the engine is running and the drive wheels are rotating Use only certified jack stands Actual body and frame colors may be different than what is represented in the picture 16 2ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Section 3 Adjustments Table of Contents NOTE Refer to Figure 3 6 The front brake link is not adjustable Front brake link right side
57. oose for ease in shipping The control lever s upper bolts 4 and nuts 5 are removed and the levers are rotated down 1 Refer to Access to Engine amp Hydraulic Pumps on page 26 The seat platform is hinged at the front To raise it release seat platform latch and tilt the seat platform up and forward The seat platform catch will prevent it from going all the way over Mount seat 1 in the operating position to the seat l platform with four 5 16 nuts 3 and four 5 16 flat washers 2 Connect the switch wires on the mower with the switch wires on the seat Return seat platform to normal operating position Rotate the control levers up until the holes line up and replace the bolts and flat washers as shown Control Lever amp Seat Assembly 21053 Figure 1 1 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 Table of Contents Section 2 Operating Ignition Switch Throttle Lever Control Levers Blade Engagement Switch Deck Lift Pedal Hour Meter Oil Pressure Light Fuel Tanks Hydraulic reservoir Land Pride Left Deck Cover Right Deck Cover Deck Height Control Park Brake Switch Choke Lever 10 Battery 11 Deck Adjusting Rod 12 Anti Scalp Wheels 13 Discharge Chute Razor Pro Controls Figure 2 1 Ay warnine Do not operate mower while smoking Controls Refer to Figure 2 2 IMPORTANT When access i
58. operator Dual steering levers which control each drive wheel have a shape and position that is very user friendly hand and arm fatigue are greatly minimized Reinforced front edge where most of the punishment happens Frame Extra strong welded and formed frame design with 1 1 2 x 2 x 125 tubing Floating deck design Deck height adjustment Anti scalp rollers 4 Deck has chain suspension which offers excellent flotation over uneven terrain Height is changed by a spring loaded foot operated lever and pin Easier than hand levers to push and faster than waiting on an electric actuation Front middle and front corners to keep scalping to a minimum Cutting height 1 1 2 to 4 1 2 Range in 1 4 increments to cut any type of turf grass Tires High blade tip speed Wide tires offer excellent ground flotation Heavy wheel forks take abuse 44 16 100 fom 52 18 300 fom Assures a good finish cut High lift blades Heavy duty high lift blades are 25 thick to handle the wear with a high lift design to stand the grass up before cutting 1 Blade spindles 1 Blades spindles with sealed ball bearings handle heavy shock loads Single belt drive Single belt design offers easier maintenance over multiple belt designs less expensive to maintain Electric clutch control Parking Brake amp Safety Lockout Easy and smooth engagement of the mower blade drive system Par
59. or to operation and follow the recommenda tions to help ensure safe and efficient operation The information contained within this manual was current at the time of printing Some parts may change slightly to assure you of the best performance To order a new Operator s or Parts Manual contact your authorized dealer Manuals can also be downloaded free of charge from our website at www landpride com or printed by your dealer from the Land Pride Service amp Support Center CD Rom Terminology Right or Left as used in this manual is determined by facing the direction the machine will operate while in use unless otherwise stated Definitions NOTE A special point of information that the operator must be aware of before continuing IMPORTANT A special point of information related to its preceding topic Land Pride s intention is that this information should be read and noted before continuing Owner Assistance The Warranty Registration card should be filled out by the dealer at the time of purchase This information is necessary to provide you with quality customer service If customer service or repair parts are required contact a Land Pride dealer A dealer has trained personnel repair parts and equipment needed to service the mower The parts on your Razor Pro Mower have been specially designed and should only be replaced with genuine Land Pride parts Therefore should your Razor Pro require replacement p
60. osen the brake linkage jam nuts Figure 3 10 8 Rotate the tire and at the same time rotate the turnbuckle to shorten the length of the brake linkage to increase the brake pressure When you feel the brake begin to engage stop adjusting the turnbuckle Retighten the jam nuts on the turnbuckle 9 Refer to Figure 3 11 Place the control lever in the park brake slot The tire should not rotate when the control lever is in the park brake position Control Lever in Park Brake Position i Control Lever Position Figure 3 11 10 Place the control lever in the neutral position The tire should rotate freely 11 Close the hydraulic pumps bypass valve 12 Repeat steps 3 thru 11 for the other side 13 Remove the jack stands and lower the unit It is now ready to operate Hydro Drive Belt Adjustment Refer to Figure 3 12 The pump drive belt tension remains constant by means of a tension idler and spring There is no tension adjustment of this belt Pump Drive Belt Figure 3 12 Deck Drive Belt Adjustment Refer to Figure 3 13 The spindle belt tension remains constant by means of a tension idler and spring The spring tension should be such that the belt does not slip under normal operating load conditions assuming the belt is not excessively worn or damaged As belt stretches and wears in adjustment may become necessary To increase belt tension move the spring chain one or more link s at the anchor brack
61. r Drain amp Filler Tube Figure 4 9A Engine Oil Filler Tube Oil Cooler 24 HP Only Oil Filter Drain Plug 21064 Honda Engine Oil Filter Drain amp Filler Tube Figure 4 9B Engine Air Filter Refer to Figure 4 10 Perform engine air filter maintenance per Maintenance Schedule on page 23 A specially designed dry filter is standard equipment on the Razor Pro and supplies clean combustion air to the engine Figure 4 10 Many engine failures can be attributed to improper air cleaner servicing Ingested dust and dirt will cause cylinder piston and bearing damage in a few hours Dusted engines will result from 1 Over servicing the air filter element 2 Improper installation of an air filter element 3 Damaged filter seals or canister 4 Incorrect air filter element size and or use of poorly designed aftermarket air filter elements Air cleaner servicing is an inexpensive maintenance check that can prevent costly non warrantable premature engine damage Over Servicing Over servicing occurs when an air filter element is removed for cleaning or replacement before it is necessary Each time the filter is removed a small amount of dirt and dust could fall in the intake system This accumulated dirt can cause a dusted engine It only takes a few grams of ingested dirt over the normal service life of an engine to cause a dusted engine Do not clean element replace with a new element only Cleaning
62. ration Of course at some point the filter media becomes too clogged to allow air to pass The mowing conditions will determine the frequency of air filter element changing Improper Installation Dust must not leak past the seals on each end of the air filter element The filter must be aligned within the canister and properly seated for an effective seal so that no dirt can enter the engine Damaged filter Seals or Canister Never bang or bump the filter element against the tire or any solid object as dust and dirt particles will be forced through the media causing continual passing of dirt into the engine Visually inspect the outside of the air cleaner canister periodically for external damage and replace if necessary Incorrect Air Filter Element Use only the correct Donaldson air filter element Land Pride part number 839 312C which is designed to fit the canister properly Land Pride air filter elements have the correct media composition filter area micron size and dimensions Always use genuine Land Pride filters Many aftermarket filters have been found to be incompatible with Land Pride s canisters and engines The air filter must remain intact to block passage of dirt and foreign particles from entering the engine Being inclined to disbelieve the need for more expensive air filter elements used on gasoline engines may cause some individuals to opt for a less expensive part The filter element must be sufficient
63. rienced operator should not mow on slopes or on uneven terrain Ay warnine The mower s control levers are very responsive Easy does it For smooth operation move lever slowly avoid sudden movement Skill and ease of operation come with practice and experience Inexperienced operators may have a tendency to over steer and lose control Slow moving practice maneuvers are recommended to become familiar with these characteristics before attempting normal speed operation Ay warnine Sharp depressions or raised obstacles such as gutters or curbs should not be directly approached at high speed in an attempt to jump them as the operator could be thrown from the mower Approach at a slow speed and angle one drive wheel at the obstruction Continue at an angle until the wheel clears and then pivot the opposite wheel around When turning on soft wet turf keep both wheels rolling either forward or backward Pivoting on one stopped wheel can damage turf This is especially important when mowing Peak mowing performance is maintained when the throttle is set at full rom This gives maximum power to the drive wheels and deck when needed Use the control levers to control ground speed rather than engine rpm Ay warnine Do not operate the equipment while wearing sandals tennis shoes sneakers shorts or any type of loose fitting clothing Always wear long pants safety glasses and safety shoes when operating this machine Keep bl
64. rolonged breathing of vapors Keep face away from nozzle and gas tank or conditioner opening Keep gas away from eyes and skin 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 27 Table of Contents Section 4 Maintenance and Lubrication Land Pride The fuel tanks are located in the tractor s fenders Total capacity for the fuel tanks is 12 2 U S gallons When filling the fuel tanks disengage blade engagement place control levers in park brake position and stop tractor engine Clean around the fuel tank cap and remove the cap and begin filling When finished screw the cap on securely and wipe up any spilled gasoline Use regular unleaded gasoline with an octane rating of 87 or higher IMPORTANT Never use methanol gasoline containing methanol or gasohol containing more than 10 ethanol because the fuel system could be damaged Do not mix oil with gasoline Using a fuel stabilizer conditioner in the tractor can provide benefits such as 1 Keeps gasoline fresh during storage of 90 days or less For longer storage drain the fuel tanks 2 Cleans the engine during operation 3 Eliminates gum like varnish build up in the fuel system IMPORTANT Do not use fuel additives containing methanol or ethanol Add the correct amount of gas stabilizer conditioner to the gas Follow the gas stabilizer conditioner manufacturer s directions for best results The fuel filter Figure 4 8A is installed in
65. s bent cracked or broken Warped Blade Replace Cutting Plane 19076 Straight Blade Comparison of Warped and Straight Blades Figure 4 14 Cutting Edge Twisted Blade Edge Replace Cutting Plane Cutting Edge 19077 Straight Blade Edge End View of Blades Twisted amp Straight Blades Figure 4 15 Mower Blade Removal and Sharpening Refer to Figure 4 16 Use a 15 16 wrench to remove the 5 8 cap screw holding blade to spindle saddle from underneath Sharpen the blades on a grinder following resharpening pattern as shown in Figure 4 16 Touch up sharpening can be done with a file Check the blades for balance following grinding A commercial balancing tool is available through most hardware supply stores or balancing can be done by placing the blade on an inverted line punch or 5 8 bolt Blade should not lean or tilt Spin the blade slowly blade should not wobble If blade is out of balance true it up before reinstalling Lay the blade on a flat surface and check for distortion Replace any distorted blade Refer Figure 4 14 and Figure 4 15 on this page 32 2ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Section 4 Maintenance and Lubrication Table of Contents Do not re use spindle bolts which have stripped worn or undercut threads Do not re use spindle bolts which have stripped worn or undercut threads Torque bolts to 118 foot pounds when reinstalling bl
66. s required under the seat platform make certain to place the control arms in the park brake position out and pivot the arm rests upward before placing the seat platform in the full forward position to prevent arm rest damage For general location of controls described in this section refer to Figure 2 1 Ignition Switch A three position switch off run and start With key inserted rotate it clockwise to START position release key when engine starts and switch will automatically return to the RUN position Throttle Control A cable is linked to engine throttle for controlling engine speed Move lever forward to increase engine rom move lever rearward to decrease engine rpm Choke Control A cable is linked to manually operate the engine choke When the lever is in the down position the choke is in the off run position When the lever is pulled up the choke is in the on start position DO NOT operate the machine with the choke in the on start position Switch Control Panel Figure 2 2 8 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Section 2 Operating Table of Contents Left Right Fuel Tank Valve Refer to Figure 2 3 The mower is equipped with a Left Right Fuel Tank Valve located on the right side behind the seat It determines which fuel tank the mower is operating from It is not important which fuel tank the mower is using Left Right Fuel Tank Sw
67. s to stop or slow mower Refer to Figure 2 5 A DANGER When going in reverse push forward gently on control levers and avoid sudden movement Any sudden movement could cause the front of the mower to come off of the ground resulting in possible loss of control To Stop or decrease speed Move control levers to neutral When going forward pull back gently on control levers When going in reverse push forward gently on control levers To Increase Speed Increase control levers equal distance from neutral The farther forward control levers are from neutral the faster the mower will travel forward The farther back the control levers are from neutral the faster the mower will go in reverse 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 11 Table of Contents Section 2 Operating Land Pride Front of Mower Faces This Direction Forward Travel Pivot Right Turn N Neutral Position Direction of arrows indicate direction of mower movement Forward Travel Right Turn N a j Reverse Travel Reverse Travel Right Turn Steering Figure 2 8 Operating Suggestions DANGER Prior to operating the mower the operator should be thoroughly familiar with the proper use and operation of the equipment should read the manual completely and thoroughly and should have attempted slow moving maneuvers to become familiar with the operation of the equipment before attempting normal speed operation An inexpe
68. size and construction to withstand stresses caused by rapid cycling of the air volume demanded by the engine without cracking or tearing under fatigue and pressure Therefore Land Pride and the engine manufacturers have carefully selected a reliable filter designed to fit the needs of the engines The filter specified is a Donaldson filter Land Pride part number 839 312C Owners should be reminded that failure to use original equipment replacement parts is an alteration and will not be considered for warranty in the event of engine damage Engine Air Filter Service Procedure 1 Release clamps and remove element Clean the canister with a damp cloth 2 Before installing anew element inspect it by placing a bright light inside and rotate the element slowly looking for any holes or tears in the paper Also check gaskets for cuts or tears Do not attempt to use a damaged element which will allow abrasive particles to enter the engine 3 Reinstall the dust cup Make sure it seals all the way around the air cleaner body then tighten the clamps 4 Check all fittings and clamps periodically for tightness and inspect hoses for holes or cracks 5 Periodically check the intake hose for signs of ingested dust Locate and repair the source of ingested dirt 6 Never operate a machine without an air filter installed General Engine Maintenance Detailed instructions and recommendations for break in and regular maintenance are sp
69. son No other warranty of any kind whatsoever express or implied is made with respect to this sale and all implied warranties of merchantability and fitness for a particular purpose which exceed the obligations set forth in this written warranty are hereby disclaimed and excluded from this sale This Warranty is not valid unless registered with Land Pride within 30 days from the date of purchase by the end user 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 41 Corporate Office PO Box 5060 Salina Kansas 67402 5060 USA www landpride com
70. tart interlock system is also designed to protect the operator and others from accidental injury due to unintentional engine starting The engine starting motor will not engage until the following two criteria are meet e Control levers are in the brake position Blade engagement switch is in the down OFF position Ay warnine The safety interlock system must not be disconnected or bypassed NOTE The operator s seat is equipped with a separate safety switch If for any reason the operator should become unseated when the neutral switches are disengaged or the blade engagement switch is engaged the engine will stop The following steps are the correct procedures for starting the engine If difficulty is encountered contact the Land Pride Dealer in your area 1 Before starting mower each day perform daily pre operation checking See Safety Start Interlock System on this page 2 Make sure the control levers are in the brake position and blade engagement switch is disengaged 3 Set throttle at approximately 1 2 open position NOTE Use choke position when engine is cold or if warm engine fails to start within 5 seconds of cranking Avoid flooding and operate engine without choking as soon as possible 4 Insert key in ignition switch and rotate clockwise to engage starting motor Release key when engine starts 10 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Sec
71. ted to the most extreme situations typically for machine components that for functional purposes cannot be guarded 4 WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury and includes hazards that are exposed when guards are removed It may also be used to alert against unsafe practices CAUTION Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices Keep Riders Off Machinery A Riders obstruct the operator s view they could be struck by foreign objects or thrown from the machine A Never allow children to operate equipment For Your Protection A Thoroughly read and understand the Safety Label section read all instructions noted on them Shutdown and Storage A Put mower in park turn off engine and remove the key A Store in an area where children normally do not play 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 1 Table of Contents Important Safety Information Land Pride These are common practices that may or may not be applicable to the products described in this manual Practice Safe Maintenance A Understand procedure before doing work Use proper tools and equipment refer to Operator s Manual for additional in
72. teering Linkage Refer to Figure 3 1 The neutral adjustment for the control levers in the neutral position is discussed in this section The steering has been factory adjusted to eliminate creeping when the control levers are in neutral position However should the mower begin to creep adjustments Figure 3 1 14 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 7 14 08 Land Pride Section 3 Adjustments Table of Contents Control Lever Neutral Adjustment Refer to Figure 3 2 Before considering any adjustment check the tire air pressure and make certain hydraulic system oil is at operating temperature Unequal tire pressure will cause the mower to drift to one side Refer to Tire Inflation Chart on page 19 and page 39 Fine adjustment to the steering is made with the adjustable pump linkage rods located between the control lever and pump arms a Steering Control Linkage Figure 3 2 Neutral is properly adjusted when the control levers are in the neutral position and the drive wheels are not turning If the mower creeps in the neutral position the control linkage may be adjusted as follows 1 Raise and block the mower up so the drive wheels are off of the floor Ay warnine Make certain mower is secure when it is raised and placed on the jack stands The jack stands should not allow the mower to move when the engine is running and the drive wheels are rotating Use only certified jack st
73. teering ee a A EE EEE O 11 Belt Replacement EEE E E E se aoa aunls 30 Controlling the Speed 0 0 11 Deck Drive Belt bette eens 31 To Stop or decrease speed 11 Integrated Pump Motor Drive Belt 31 To Increase Speed 0 000 eee 11 Deck Belt Drive Layout 31 Operating Suggestions 0005 12 Pump Belt Fayo es S yey O Sl Mower Deck Operation 00 000 13 Mower Blade Maintenance Fett t eee 32 Operating Instfuctions i6susewdtewsawawans 13 epee Removal and Sharpening Pen eee PEN PM a hee Fe n Preparation of Engine for Storage 33 Torque Values E E A Ee seer ee 14 New Season Preparation 0050 33 Steering Linkage 14 Section 5 Specifications and Capacities 34 Control Lever Neutral Adjustment 15 Section 6 Features and Benefits 36 Control lever StOPS 0 0 0 c eee eee 15 Section 7 Troubleshooting 37 Steering Dampener 220000 ee 16 Control Lever Adjustment 16 Section 8 Appendix 39 Park Brake Adjustment 0 16 Torque Values Chart for Common Bolt Sizes 39 Hydro Drive Belt Adjustment 18 Tire Inflation Chart 0000 00 eee 39 Deck Drive Belt Adjustment 18 NALIN tials ha ate ett tle te tia a oe tet al lel 41 Engine RPM Setting 20000 19
74. thing and equipment should be worn A Wear clothing and equipment appropriate for the job Avoid loose fitting clothing A Prolonged exposure to loud noise can cause hearing impairment or hearing loss Wear suitable hearing protection such as earmuffs or earplugs A Operating equipment safely requires the full attention of the operator Avoid wearing radio headphones while operating machinery Nak Ju Avoid High Pressure Fluids Hazard A Escaping fluid under pressure can penetrate the skin causing serious injury A Avoid the hazard by relieving pressure before disconnecting hydraulic lines A Use a piece of paper or cardboard NOT BODY PARTS to check for suspected leaks A Wear protective gloves and safety glasses or goggles when working with hydraulic systems A If an accident occurs see a doctor immediately Any fluid injected into the skin must be surgically removed within a few hours or gangrene may result WT Safety Labels 1 Your mower comes equipped with all safety labels in place They were designed to help you safely operate your mower Read and follow their directions 2 Keep all safety labels clean and legible 3 Replace all damaged or missing labels To order new labels go to your Land Pride dealer 4 Some new equipment installed during repair requires safety 5 Refer to this section for proper label placement b Spray soapy water on the surface where the label is to
75. tion 2 Operating Table of Contents IMPORTANT The engine starter should not be operated for periods longer then 30 seconds at atime An interval of at least two minutes should be allowed between such cranking periods to protect the starter from overheating and burn out 5 Perform test to make sure safety start interlock system is operating properly Refer to Safety Start Interlock System on page 10 6 As soon as engine begins to run check to make certain the oil warning light is off If not stop engine immediately and check for the cause Refer to Section 7 Troubleshooting on page 37 7 Allow the engine to idle a few minutes before advancing the throttle and or engaging the blade clutch 8 Before stopping the engine place the control levers in the brake position disengage the blade engagement and throttle back to low idle for a couple of minutes then rotate ignition key counter clockwise to the OFF position Remove the key from switch before leaving the seat Ay warnine Never leave the machine unattended with key in ignition switch Moving Mower with Stalled Engine Refer to Figure 2 7 The mower hydro drives are equipped with bypass valves for moving the mower when the engine is inoperable The valve stems to the bypass valves are located near the top of the hydraulic pumps and are identified as a hex stud Before moving the unit turn each bypass valve stem counter clockwise one half to one re
76. used air filter elements through improper cleaning procedures can get dust on the inside of the filter causing dirt ingestion and engine failure 7 14 08 ZRP44 amp ZRP52 Zero Turning Radius Mowers 356 117M 29 Table of Contents Section 4 Maintenance and Lubrication Land Pride It is important to note that whenever an air filter element is cleaned by any method the person or company performing the cleaning assumes responsibility for the integrity of the filter from then on The Donaldson warranty for air filters expires upon cleaning or servicing in any manner because the condition of the filter after servicing is completely out of their control Therefore on a dust ingested engine failure there will be no warranty consideration if the air filter element has been cleaned or serviced in any manner A partially dirty air filter element works better than a new element Therefore a dirty filter element is not bad for the engine unless it is excessively restricting the air flow and engine performance is affected The reason is the media in the filter must be porous to allow air to pass through it When dirty air passes through the filter the dirt plugs some of the holes in the media and actually acts as part of the filter media When the next round of dirt enters the first dirt helps filter out even smaller particles making the filter more efficient at stopping dirt from entering the engine This is referred to as barrier filt
77. volution and place the control levers in neutral position Do not tow the machine Move it by hand or use a winch to load it on a trailer for transporting When transporting on another vehicle the tractor should be facing forward and it must be secured Bypass Valve Figure 2 7 IMPORTANT Following repairs always make certain the two bypass valve stems are returned to their operating position before running the mower Driving the Mower A DANGER Never make sudden stops or sudden reversing of direction especially when going down a slope The steering is designed for sensitive response Rapid movement of the control levers in either direction could result in a reaction of the mower that can cause Serious injury Steering Refer to Figure 2 8 on page 12 After starting engine engage the control levers and steer as follows e To Go Forward Push control levers forward an equal distance e To Go in Reverse Pull control levers rearward an equal distance e To Turn Left Move the right control lever farther forward from neutral than the left control lever e To Turn Right Move the left control lever farther forward from neutral than the right control lever e To Pivot Turn Move one control lever forward and the other control lever back of neutral this will allow the drive wheels to counter rotate Controlling the Speed Ay warnine In the event of a system failure while mowing engage both parking brake
Download Pdf Manuals
Related Search
Related Contents
Hinweis zur Gebrauchsanweisung PIX-200 - Global Time Systems 取扱説明書 - M Oster CKSTPM5450 Instruction Manual Eli-LED Philips FXD58 Samsung SGH-X820 Benutzerhandbuch Product Specification Copyright © All rights reserved.
Failed to retrieve file