Land Pride Power Screwdriver Powered Ditchers User's Manual
Contents
1. WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury and includes hazards that are exposed when guards are removed It may also be used to alert against unsafe practices A CAUTION Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices Shutdown and Storage A Lower machine to ground put tractor in park turn off engine and remove the key A Detach and store implements in a area where children normally do not play Secure implement by using blocks and supports 3 17 08 DT55 amp DTM55 Powered Ditchers 324 053M 1 Table of Contents Land Pride Important Safety Information These are common practices that may or may not be applicable to the products described in this manual Use Safety Lights and Devices A Slow moving tractors self propelled equipment and towed implements can create a hazard when driven on public roads They are difficult to see especially at night A Flashing warning lights and turn signals are recommended Transport Machinery Safely A Comply with state and local laws A Maximum transport speed for implement is 20 mph DO NOT EXCEED Never travel at a speed which does not allow adequate control of steering and stopping Some rough terrain require a slower speed A Use the following maximum spee2. 0 18 Section 1 Assembly and Set Up 8 Output Shaft Bearings 18 Tractor Requirements 000000 8 Drive Chain L ccs ease cig cree teeny 18 oie ui E gt aeeewarsraey arate Driveline Shafts astelas sass Ys ace dete 19 Checking Driveline Minimum Length 8 Driveline U Joints Zerks Both Ens 19 Driveline Maximum Allowable Length 9 PG NSLP HOMES AMINE inci deand nara grt r Manual Chute Option Assembly 10 Section 5 Specifications amp Capacities 20 Hydraulic Chute Option Assembly 10 Section 6 Features amp Benefits 21 Ripper Option Assembly 5 11 i A Skid Shoe Option Assembly 11 section 1 Troubiesnoonng eo 22 Gauge Wheel Option Assembly 41 Section 8 Appendix 23 k Torque Values Chart For Common Bolt Size 23 Section 2 Operating Instructions 12 ee oA Transporting 00 cece eee eee 12 Warranty 0 0 cece cece cece eee e eres 25 Operating Checklist 2 00000 12 Operating Instructions 00000e 12 General Operating Instructions 12 Copyright 2008 All rights Reserved Land Pride provides this publication as is without warranty of any kind either expressed or implied While every precaution has been taken in the preparation of this manual Land Pride assumes no responsibility for errors or omissions Nei
3. Ditchers 324 053M 9 Table of Contents Section 1 Assembly and Set Up IMPORTANT A small chain is supplied with the driveline This chain must be attached to the inner driveline shield and to the Powered Ditcher to restrict shield rotation 6 Hook driveline safety chain in the hole in the inner driveline guard Attach the other end to the Powered Ditcher s main frame Start tractor and raise Powered Ditcher just enough to remove support blocks Slowly engage tractor s 3 point controls to lower Powered Ditcher Check for sufficient drawbar clearance Move drawbar ahead aside or remove if required Raise and lower implement to find the maximum possible extended driveline length Check to make certain that the driveline has not extended beyond the maximum allowable length recorded in step 3 on page 9 Manual Chute Option Assembly Refer to Figure 1 4 1 Assemble Chute 1 to the main frame with hinge pin 3 and cotter pins 4 Bend one leg of each cotter pin to keep cotter pin from falling out Attach ratchet jack 5 to the chute and frame lugs as shown with clevis pins provided Secure clevis pins with hair pin cotters Manual Chute Option Assembly Figure 1 4 Land Pride Hydraulic Chute Option Assembly Refer to Figure 1 5 Assemble Chute 1 to the main frame with hinge pin 2 and cotter pins 3 Bend one leg of each cotter pin to keep cotter pin from falling out Attach
4. Land Pride s judgment shall have been misused or damaged by accident or lack of normal maintenance or care or which has been repaired or altered in a way which adversely affects its performance or reliability or which has been used for a purpose for which the product is not designed Misuse also specifically includes failure to properly maintain oil levels grease points and driveline shafts Claims under this Warranty should be made to the dealer which originally sold the product and all warranty adjustments must be made through an authorized Land Pride dealer Land Pride reserves the right to make changes in materials or design of the product at any time without notice This Warranty shall not be interpreted to render Land Pride liable for damages of any kind direct consequential or contingent to property Furthermore Land Pride shall not be liable for damages resulting from any cause beyond its reasonable control This Warranty does not extend to loss of crops any expense or loss for labor supplies rental machinery or for any other reason No other warranty of any kind whatsoever express or implied is made with respect to this sale and all implied warranties of merchantability and fitness for a particular purpose which exceed the obligations set forth in this written warranty are hereby disclaimed and excluded from this sale This Warranty is not valid unless registered with Land Pride within 30 days from the date of purchase b
5. Table of Contents Section 1 Assembly and Set Up Tractor Requirements This Powered Ditcher is designed with a Category 2 and 3 3 point hitch The maximum horsepower rating for the tractor is 120 HP depending on lift capacity and field conditions Front tractor weights and or ballast to tires may be required to offset weight of unit Consult your tractor manual for details Ay CAUTION Your Ditcher must be mounted only on a tractor equipped with a Category 2 or 3 hitch Failure to do so may result in serious injury Tractor Hook Up A DANGER Tractor hook up to equipment is dangerous and can result in serious injury or death Do not allow anyone to stand between the Powered Ditcher and tractor during hook up operations Do not operate the hydraulic 3 point lift controls while someone is directly behind the tractor or near the implement A DANGER Hydraulic fluid under pressure can penetrate skin Wear protective gloves and safety glasses or goggles when working with hydraulic systems Use a piece of cardboard or wood rather than hands when searching for hydraulic leaks If hydraulic fluid is injected into the skin it must be treated by a doctor within a few hours or gangrene may result 1 Slowly back tractor up to the Powered Ditcher while using the tractor s 3 point hydraulic control to align the lower hitch link holes with the clevis lug holes on the implement 2 Engage tractor park brake shut tractor engine of
6. breakdown A driveline that is operating must not exceed an angle of 25 degrees up or down while operating the 3 point lift See Figure 1 1 below DRIVELINE LEVEL Maximum Allowable Driveline Movement Figure 1 1 Checking Driveline Minimum Length IMPORTANT Always check driveline minimum length and maximum allowable length during initial setup and when connecting to a different tractor More than one driveline may be required to fit all applications 8 DT55 amp DTM55 Powered Ditchers 324 053M 3 17 08 Land Pride Section 1 Assembly and Set Up IMPORTANT It is necessary to align the tractor s PTO shaft level with the Powered Ditcher s drive shaft when checking driveline minimum length Too long a driveline can damage tractor driveline and Powered Ditcher 1 Start tractor and slowly engage tractor s hydraulic 3 point lever to move the lower arms up or down until the driveline shaft is approximately level Securely block the Powered Ditcher in this position Refer to Figure 1 2 on page 9 2 Place tractor gear selector in park shut tractor engine off set park brake and remove switch key IMPORTANT The inner shield half attaches to the Ditcher 3 Attach driveline to Powered Ditcher and tractor as follows a Slide inner universal joint of driveline over the Powered Ditcher s drive shaft and secure with locking collar b Slide outer universal joint driveline over the tractor s PTO
7. d Bolt idler assembly to inside of chain case with existing 3 8 16 hex flange lock nuts 15 Tighten 3 8 nuts to the correct torque Replace drive sprocket 20 and driven sprocket 21 as follows a Remove lock collars 31 from rear flange bearings 29 and front flange bearings 30 b Remove 5 8 11 x 1 1 2 GR5 hex cap screws 8 lock washers 18 rear flange bearings 29 and bearing gaskets 26 c Loosen set screws in sprockets 20 amp 21 There are 2 set screws for each sprocket d Pull upper drive shaft 25 and lower impeller shaft 4 towards front of implement while sliding sprockets 20 amp 21 off the shafts Be careful not to loose woodruff keys 7 e Install new sprockets 20 amp 21 and reassemble by reversing above process Install new chain from the top by using a pull line or wire to help guide chain around sprockets so you can add master link at top center Refer to Drive Chain Adjustment on page 14 to properly adjust roller chain tension Install rear inspection plate 2 and gasket 27 with lock washer 16 and 1 4 2 x 5 8 GR5 hex head cap screws 11 Table of Contents Install top cover plate 1 and cover gasket 28 with galvanized rubber clad washers 19 lock washers 17 and 3 8 16 x 1 1 4 GR5 hex head cap screws 12 Tighten cap screws to the correct torque IMPORTANT Make sure not to forget to install 3 8 galvan
8. shaft and secure with locking collar c Skip to Driveline Maximum Allowable Length if driveline fits m NV INNER DRIVEL Z Fi x1 INNER SHAFT INNER SHIELD IMPLEMENT EN UNIVERSAL _ JOINT SHIELD OUTER DRIVELINE ZY N ED a TRACTOR END a Pa OUTER SHAFT OUTER SHIELD 23758 Driveline Shortening Figure 1 2 4 The driveline will require shortening if it is too long to fit between the tractor and Powered Ditcher Shorten driveline as follows a Make sure the Powered Ditcher and tractor PTO shafts are level with each other and the implement is securely supported at this height with support blocks b Pull driveline profiles apart into two sections as Table of Contents gearbox shaft Pull on each driveline section to be sure universal joints are secured d Hold driveline sections parallel to each other to determine if they are too long The inner and outer shields on each section should end approximately 1 short of reaching the universal joint shield on the adjacent section see B dimension If they are too long measure 1 B dimension back from the universal joint shield and make a mark at this location on the inner and outer shields e Cut off inner shield at mark X dimension Cut same amount off inner shaft X1 dimension Repeat cut off procedure Y amp Y1 dimensions to cut oute
9. ITT LYELL POLL 4 ZAC 0 K Li Wy GoM AIZEG YH 1QYGIOYUS AG AW LEE LLL 838 112C Chute Option Both Sides Danger Pinching A WARNING HIGH PRESSURE FLUID HAZARD a eath e Relieve pressure on system before repairing or adjusting or disconnecting e Wear proper hand and eye protection when g or leaks Use e Keep all co w searchi wood or cardboard instead of hands onents in good repair 838 0946 838 094C Hydraulic Chute Option Warning Hydraulic Pressure 6 DT55 amp DTM55 Powered Ditchers 324 053M 3 17 08 Land Pride Introduction Table of Contents Land Pride welcomes you to the growing family of new product owners This Ditcher has been designed with care and built by skilled workers using quality materials Proper assembly maintenance and safe operating practices will help you get years of satisfactory use from the Powered Ditcher Application The DT55 Powered Ditcher is a versatile tool to use in many water control applications Cleaning water ditches along roadsides or in farm fields to drain standing water away from crops the DT55 makes it simple The 20 impeller leaves a clean and sculptured trough to keep water flowing freely from unwanted areas With the optional Material Control Chute in place dirt can be placed just next to the machine or thrown many feet away to reshape terraces An optional ripper gauge wheel and skid shoe can be attached to aid in re
10. Land Pride dealer A dealer has trained personnel repair parts and equipment needed to service the Powered Ditcher The parts on your Powered Ditcher have been specially designed and should only be replaced with genuine Land Pride parts Therefore should your Ditcher require replacement parts go to your Land Pride Dealer Serial Number Plate For prompt service always use the serial number and model number when ordering parts from your Land Pride dealer Be sure to include your serial and model numbers in correspondence also Refer to Figure 1 for the location of your serial number plate Serial Number Plate Location Figure 1 Further Assistance Your dealer wants you to be satisfied with your new Powered Ditcher If for any reason you do not understand any part of this manual or are not satisfied with the service received the following actions are suggested 1 Discuss the matter with your dealership service manager making sure he is aware of any problems you may have and that he has had the opportunity to assist you 2 Ifyou are still not satisfied seek out the owner or general manager of the dealership explain the problem and request assistance 3 For further assistance write to Land Pride Service Department 1525 East North Street P O Box 5060 Salina Ks 67402 5060 E mail address lpservicedept landpride com 3 17 08 DT55 amp DTM55 Powered Ditchers 324 053M 7
11. Table of Contents Powered Ditchers DT55 amp DTM55 25751 324 053M Operator s Manual Read the Operator s manual entirely When you see this symbol the subsequent instructions and warnings are serious follow without exception Your life and the lives of others depend on it Copyright 2008 Printed 3 17 08 Cover photo may show optional equipment not supplied with standard unit Table of Contents Important Safety Information 1 Section 3 Adjustments 14 Safety at All Times 2 000 00055 1 Drive Chain Adjustment 14 Look For The Safety Alert Symbol 1 Gauge Wheel 6 06 ade eae ee a eee 14 Safety Labels sc ccwciw eect eewieewie eee ees 4 Manual Chute Adjustment 14 Introduction 7 Hydraulic Chute Adjustment 15 ies ee ee Ripper Depth Adjustment 15 Application 0 00 ee 7 Using This Manual 0 00 00000 7 Section 4 Maintenance amp Lubrication 16 Terminology Sree Ge oe ee ee ee ee ee 7 Maintenance 0 cee eee 16 Defis icc forse a T T EE 7 Storage eee eee 16 Owner Assistance ccc ccc cccecccecccees 7 Drive Chain Maintenance 16 Serial Number Plate 22 7 Drive Sprocket and Drive Chain Replacement 17 Further Assistance L L L L LLL 7 Lubrication Peete etna 18 Input Shaft Bearing 0 0
12. You will also want to make sure that there are no people animals pets valuable property and or equipment in the immediate vicinity that could be harmed by flying rocks dirt or debris once you engage the Powered Ditcher 12 DT55 amp DTM55 Powered Ditchers 324 053M 3 17 08 Land Pride Table of Contents Section 2 Operating Instructions If your unit has an optional depth controlling skid shoe and if you have not already set it to the desired depth you should set the tractor s park brake shut tractor engine off remove switch key and then make that setting You are now ready to begin operation Make sure the unit is lifted just barely off of the ground raise the tractor engine rpm slightly above idle and engage the PTO The best ditching performance is usually achieved at forward speeds of approximately 3 to 5 mph so make the proper gear selection and then raise engine rpm to full PTO speed Begin forward motion while gently lowering the Powered Ditcher into working position You will immediately begin to see a generous stream of dirt being rapidly ejected off to the left side If you are not using a deflector shield the dirt will usually be ejected outward and will spread evenly over the ground 20 to 50 out If you are using a deflector shield to form a burm or terrace now is the time to make sure your chute is correctly adjusted to achieve the desired results After you have traveled approximately 50 it is a goo
13. and Pride Important Safety Information Safety Labels specified by Land Pride When ordering new components make sure the correct safety labels are included in the Your Ditcher comes equipped with all safety labels in place request They were designed to help you safely operate your implement 4 Refer to this section for proper label placement Read and follow their directions To install new labels 1 Keep all safety labels clean and legible a Clean the area the label is to be placed 2 Replace all damaged or missing labels To order new b Spray soapy water on the surface where the label is to labels go to your nearest Land Pride dealer or visit our be placed dealer locator at landpride com 3 Some new equipment installed during repair requires safety labels to be affixed to the replaced component as c Peel backing from label Press firmly onto the surface Squeeze out air bubbles with the edge of a credit card ACAUTION To avoid Injury or Machine Damage Operate only wit 540 rpm 818 1300 Rev B 818 130C DT55 Caution 540 RPM 818 240C DTM55 Caution 1000 RPM YW eT gs W ef lt alay ROTATING DRIVELINE CONTACT CAN CAUSE DEATH KEEP AWAY DO NOT OPERATE WITHOUT All driveline guards tractor and equipment shields in place 81 8 552C Drivelines securely attached at both A F 3 j ends Caution Rotating Driveline Driveline guards t
14. cations amp Capacities DT M 55 Series Powered Ditcher DT55 DTM55 Tractor PTO 540 RPM 1000 RPM Hitch Category 2 amp Category 3 Quick Hitch Adaptable Machine Weight Without Options 900 Ibs 850 Ibs Impeller Blades 6 ea 3 8 thick steel with replaceable hardened cutting edges Chain Case Oil Shell Alvania EP 00 Gear Lube Land Pride Part 821 045C 32 oz bottle Input Output Shafts 2 1 4 ID ball type bearings Driveline Cat 5 with shear bolt Material Control Chute Optional Manual or with 2 X 8 hydraulic cylinder and hoses Depth Control Wheel Optional 16 5 X 6 50 8 pneumatic tire Adjustable from cutting edge to 10 below Ripper Shank Optional 3 height adjustments from cutting edge depth to 5 below Spring tine tip Skid Shoe Optional 3 8 thick replaceable 20 DT55 amp DTM55 Powered Ditchers 324 053M 3 17 08 Land Pride Section 6 Features amp Benefits Table of Contents DT M 55 Series Powered Ditcher eS FE SE 70 120 HP HP range Cat 2 amp 3 Quick Hitch adaptable Fits wide variety of tractors Quickly and easily attach Ditcher to tractor with one person Formed tubing hitch Formed tubing with 1 4 wall offers greater strength vs plate steel hitch 540 amp 1000 rpm models 20 Impeller Allows fitting larger tractors that are 1000 rpm only Driveline available in 1 3 8 or 1 3 4 20 Impeller digs a nice
15. d tow load weight ratios as a guideline 20 mph when weight is less than or equal to the weight of tractor 10 mph when weight is double the weight of tractor IMPORTANT Do not tow a load that is more than double the weight of tractor whenever driving on public roads A Sudden braking can cause a towed load to swerve and upset Reduce speed if towed load is not equipped with brakes A Allow implement to cool completely A Do not grease or oil implement while it is in operation Practice Safe Maintenance A Understand procedure before doing work Use proper tools and equipment refer to Operator s A Ins A pect all parts Make sure parts Manual for additional information are in good condition amp installed A Workina clean dry area properly A Lower the implement to the A Remove buildup of grease oil or ground put tractor in park turn off debris engine and remove key before performing maintenance A Remove all tools and unused parts from implement before operation 2 DT55 amp DTM55 Powered Ditchers 324 053M 3 17 08 Land Pride Important Safety Information Table of Contents These are common practices that may or may not be applicable to the products described in this manual Prepare for Emergencies A Be prepared if a fire starts A Keep a first aid kit and fire extinguisher handy A Keep emergency numbers for doctor ambulance hospital and fire department near phone a P
16. d idea to lift the Powered Ditcher out of working position or soil contact safely shut your equipment down and go back to inspect the results Then make required adjustments before continuing on If your ground conditions are extremely hard you may find it necessary to employ an optional ripper attachment If your ground conditions are too wet you shouldn t run at all until drier conditions prevail Remember to look back often With a little practice you will gain the required experience you need to help you achieve the desired results you expect from your Land Pride 55 Series Powered Ditcher When you are done ditching need to take a break or just need to make a few adjustments to the Powered Ditcher always remember to do the following e Raise the Powered Ditcher up and out of soil contact e Reduce the tractor s engine rpm e Disengage the PTO e Stop on level ground e Set the park brake e Turn off the engine e Remove the key See Features and Benefits section or Product Specifications for additional information and performance enhancing options 3 17 08 DT55 amp DTM55 Powered Ditchers 324 053M 13 Table of Contents Section 3 Adjustments A CAUTION BEFORE any adjustments are performed lower the Ditcher to the ground slowly stop tractor engine and remove switch key DO NOT attempt to make adjustments while tractor is running NOTE For corrrect torque values refer to Torqu
17. e Values Chart For Common Bolt Size on page 23 Drive Chain Adjustment Refer to Figure 3 1 1 Unbolt and remove inspection cover 1 Be careful not to damage gasket 7 while removing the cover 2 Check roller chain for tightness by pressing on the chain between top and bottom sprockets Chain should have approximately 1 2 movement IMPORTANT Do Not over tighten drive chain A tight chain will have high wear 3 Ifthe chain is loose loosen jam nut 5 and turn chain adjusting bolt 3 until excess chain slack is removed Tighten jam nut 5 and recheck chain tension Replace gasket 7 if damaged during removal of inspection cover oOo IMPORTANT Loctite is required on all bolts 4 and silicone is required on gasket 7 before installation 6 Attach inspection cover 1 to the main frame with 1 4 20 x 5 8 GR5 hex head cap screw 4 and lock washer 6 Tighten cap screw to the correct torque VY Idler Spring Adjustment Figure 3 1 Gauge Wheel Refer to Figure 3 2 The Gauge Wheel can be adjusted by removing 3 4 hitch pin 3 and moving gauge wheel 1 up or down to desired depth Be sure to secure hitch pin with hair pin cotter 4 when reinstalling Ripper Depth Adjustment Refer to Figure 3 2 The Ripper option is designed to tear up hard ground for easier ditching Adjust ripper to desired depth by removing p
18. ents Section 2 Operating Instructions Transporting IMPORTANT ALWAYS disengage PTO before raising the Powered Ditcher to transport position 1 When raising the Powered Ditcher to the transport position be sure that the powershaft does not contact tractor or implement 2 Be sure to reduce tractor ground speed when turning Leave enough clearance so the Powered Ditcher does not contact obstacles such as buildings trees or fences 3 Select a safe ground travel speed when transporting from one area to another When traveling on roadways transport in such a way that faster moving vehicles may pass you Safely 4 When traveling over rough or hilly terrain shift tractor to a lower gear A CAUTION When traveling on public roads whether at night or during the day use accessory lights and devices for adequate warning to operators of other vehicles Comply with all federal state and local laws Operating Checklist Check chain tension Refer to Drive Section 3 Chain Adjustment page 14 Check oil level in chaincase Refer to Section 4 Lubrication page 18 Check that all plugs have been replaced Section 4 properly in the chaincase page 18 Check that all bolts and nuts are tight Operator s Manual Be certain all guards and shields are in place and secure Operator s Manual Grease driveline shaft and all other grease Section 4 fittings Refer to Lub
19. ers 3 ft Ib foot pounds 4mm x pitch nominal thread diameter in millimeters x thread pitch T tolerance TA 15 of ANT values TA otherwise specified use torque values listed above Tire Inflation Chart TireSize Inflation PSI 16 5 x 6 50 8 Pneumatic Tire 45 3 17 08 DT55 amp DTM55 Powered Ditchers 324 053M 23 Table of Contents Land Pride Section 8 Appendix Notes 24 DT55 amp DTM55 Powered Ditchers 324 053M 3 17 08 Land Pride Table of Contents Section 8 Appendix Warranty Land Pride warrants to the original purchaser that this Land Pride product will be free from defects in material and workmanship beginning on the date of purchase by the end user according to the following schedule when used as intended and under normal service and conditions for personal use Overall Unit One year Parts and Labor Driveline One year Parts and Labor Impeller One year Parts and Labor Hydraulic Cylinder If equipped One year Parts and Labor Impeller cutting edges blade cutting edge and ripper shank Considered wear items This Warranty is limited to the replacement of any defective part by Land Pride and the installation by the dealer of any such replacement part and does not cover common wear items Land Pride reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship This Warranty does not apply to any part or product which in
20. f and remove key before dismounting from tractor 3 With tractor s lower hitch arms aligned and positioned in the clevises attach the lower arms to the clevises with hitch pins and secure with linch pins 4 Connect top center link to the upper pivot hitch using customer supplied clevis pin and linch pin 5 Ensure that the lower hitch arms are blocked to prevent excessive side movement 6 Return to the tractor and slowly operate the 3 point controls up and down to check for clearance between the implement and tractor Move or remove the drawbar if it interferes with the Powered Ditcher 7 Manually adjust one of the two lower lift arms up or down to level the Powered Ditcher from left to right Manually adjust the length of the top link to level the Powered Ditcher from front to rear Driveline Set Up If the Ditcher is to be used on more than one tractor an additional driveline may be required especially if a quick hitch is used Do not use a PTO adaptor with a quick hitch A PTO adapter will increase the strain on the tractor s PTO shaft and can damage the PTO shaft and tiller driveline warnine Damaged drivelines can cause serious injury or death Tractor PTO shield and all Ditcher guards must be in place at all times during operation IMPORTANT Some tractors are equipped with multispeed PTO ranges Be certain your tractor s PTO is set for the correct PTO speed IMPORTANT Avoid premature driveline
21. hat turn freely on Driveline 838 111C Danger Moving Parts 4 DT55 amp DTM55 Powered Ditchers 324 053M 3 17 08 Land Pride Table of Contents Important Safety Information A O To prevent injury or death Read and understand Operator s Manual before using e Lower implement stop tractor engine set park brake and remove ignition key before servicing adjusting repairing or unplugging Do not allow riders e Keep others away during operation Safely support and secure implement before repairs are made s1a 718c 818 719C Caution General Instructions DANGER D ROTATING BLADE HAZARD To prevent serious injury or death from rotating blade o Do not go under frame when blades are tuming or engine is running Keep others away o Disconnect and lockout power source before adjusting or servicing o Keep hands feet hair and clothing away from 838 2 9 5 C moving parts Danger Rotating Blade S407 O fo a X THROWN OB 838 287C Danger Thrown Object 838 381C Danger 3 17 08 DT55 amp DTM55 Powered Ditchers 324 053M 5 Table of Contents Land Pride Important Safety Information 818 229C Chute Option Amber Reflector 818 230C Chute Option Red Reflector hf yy L
22. he Ditcher lowered completely to the ground or folded with the transport boom lock engaged and the tractor engine shut off with ignition key removed e After using the Ditcher for several hours check all bolts to be sure they are tight For corrrect torque values refer to Torque Values Chart For Common Bolt Size on page 23 Lubricate items as listed under Lubrication in this section starting on page 18 Replace any worn damaged or illegible safety labels by obtaining new labels from your Land Pride Dealer Information about labels is located under Safety Labels in the Important Safety Information section starting on page 1 Storage For short periods coat all exposed cylinder shafts with grease or a corrosion preventive Install dust caps on the quick couplers if equipped to prevent dirt contamination of the hydraulic system Or if possible connect the quick couplers together At the end of the working season or when the Ditcher will not be used for a long period it is good practice to clean off any dirt or grease that may have accumulated on the Ditcher and any of the moving parts It may be necessary to scrape off compacted dirt from the rotor blades then use a garden hose to thoroughly clean the surface Inspect the Ditcher for loose damaged or worn parts and adjust or replace if needed Lubricate as noted in the Lubrication portion of this section starting on page 18 Repaint parts where paint is wo
23. hydraulic cylinder to the chute and frame lugs as shown with clevis pins 4 Secure clevis pins with hair pin cotters Route hydraulic hoses through hose guide 5 as shown Hydraulic Chute Option Assembly Figure 1 5 10 DT55 amp DTM55 Powered Ditchers 324 053M 3 17 08 Land Pride Table of Contents Section 1 Assembly and Set Up Ripper Option Assembly Refer to Figure 1 6 1 Assemble ripper Assembly 1 to the main frame with four 3 4 u bolts 2 lock washers 3 and 3 4 nuts 4 Tighten nuts to 170 ft lbs of torque Skid Shoe Option Assembly Figure 1 7 GLD Ripper Option Assembly Figure 1 6 Skid Shoe Option Assembly Refer to Figure 1 7 1 Attach Skid Shoe 1 to the main frame with 3 8 16 x 1 1 4 GR5 round head square neck bolt s 2 and lock nuts 3 Draw lock nuts up snug do not tighten 2 Attach one end of turnbuckle 5 to the main frame lug with clevis pin 6 and cotter pin 4 3 Attach other end of turnbuckle 5 to the lug on the skid shoe 1 lug with clevis pin 6 and cotter pin 4 4 Bend one leg of each cotter pin to keep cotter pin from falling out Gauge Wheel Option Assembly Refer to Figure 1 8 1 Assemble Gauge Wheel Assembly 1 with hitch pin 2 and hair pin 3 Gauge Wheel Option Assembly Figure 1 8 3 17 08 DT55 amp DTM55 Powered Ditchers 324 053M 11 Table of Cont
24. ins 6 and moving the ripper shank 2 up or down Replace retaining pins and secure with hair pin cotters 5 Gauge Wheel Adjustment Figure 3 2 14 DT55 amp DTM55 Powered Ditchers 324 053M 3 17 08 Land Pride Section 3 Adjustments Manual Chute Adjustment Refer to Figure 3 3 The Chute controls how far and how high debris will be dispersed Raise the chute to disperse debris farther and higher Lower the chute to limit how far and how high debris is dispersed Raise or lower the chute by setting the ratchet mechanism on the jack and then pumping the jack handle Manual Chute Adjustment Figure 3 3 Table of Contents Hydraulic Chute Adjustment A CAUTION BEFORE any adjustments are performed lower the Ditcher to the ground stop tractor engine and remove switch key DO NOT attempt to make adjustments while tractor is running Refer to Figure 3 4 The Chute can be adjusted hydraulically to the desired height by adjusting tractor hydraulics Hydraulic Chute Adjustment Figure 3 4 3 17 08 DT55 amp DTM55 Powered Ditchers 324 053M 15 Table of Contents Section 4 Maintenance amp Lubrication Maintenance Proper servicing and adjustment is the key to the long life of any implement With careful and systematic inspection you can avoid costly maintenance time and repair A CAUTION For safety reasons each maintenance operation must be performed with t
25. ized rubber clad washers 19 If not replaced oil could leak out during operation Kp Ss ie ES f ti i k Li JK eo lA Ks n Drive Sprocket and Drive Chain Replacement Figure 4 1 3 17 08 DT55 amp DTM55 Powered Ditchers 324 053M 17 Table of Contents Land Pride Section 4 Maintenance amp Lubrication Lubrication Input Shaft Bearing Type of Lubrication Multi purpose Grease Quantity As required Output Shaft Bearings Type of Lubrication Multi purpose Grease Quantity As required As Required Drive Chain Oil should escape from Oil Level plug hole in chain case when the level plug is removed If oil is needed remove top fill plug and add oil until it escapes from Oil level plug hole Type of Lubrication Shell Alvania EP00 Gear Lube Land Pride Part 821 045C 32 oz bottle 18 DT55 amp DTM55 Powered Ditchers 324 053M 3 17 08 Land Pride Table of Contents Section 4 Maintenance amp Lubrication umm dics Driveline Shafts Type of Lubrication Multi purpose Grease Quantity As required CNES Driveline U Joints Zerks Both Ends Type of Lubrication Multi purpose Grease Quantity As required Gauge Wheel Option Bearing Type of Lubrication Multi purpose Grease Quantity As required 3 17 08 DT55 amp DTM55 Powered Ditchers 324 053M 19 Table of Contents Section 5 Specifi
26. nd between the tractor and implement during hitching A Keep hands feet and clothing away from power driven parts A Wear snug fitting clothing to avoid entanglement with moving parts A Watch out for wires trees etc when raising implement Make sure all persons are clear of working area A Turning tractor too tight may cause implement to ride up on wheels This could result in injury or equipment damage Look For The Safety Alert Symbol The SAFETY ALERT SYMBOL indicates there is a potential hazard to personal safety involved and extra safety precaution must be taken When you see this symbol be alert and carefully read the message that follows it In addition to design and configuration of equipment hazard control and accident prevention are dependent upon the awareness concern prudence and proper training of personnel involved in the operation transport maintenance and storage of equipment Be Aware of Signal Words A Signal word designates a degree or level of hazard seriousness The signal words are amp DANGER Indicates an imminently hazardous situation which if not avoided will result in death or serious injury This signal word is limited to the most extreme situations typically for machine components that for functional purposes cannot be guarded For Your Protection A Thoroughly read and understand the Safety Label section read all instructions noted on them
27. ort Avoid High Pressure Fluids Hazard A Escaping fluid under pressure can penetrate the skin causing serious injury A Avoid the hazard by relieving pressure before disconnecting hydraulic lines or performing work on the system A Make sure all hydraulic fluid connections are tight and all hydraulic hoses and lines are in good condition before aqpplying pressure to the system A Use a piece of paper or cardboard NOT BODY PARTS to check for suspected leaks A Wear protective gloves and safety glasses or goggles when working with hydraulic systems A If an accident occurs see a doctor immediately Any fluid injected into the skin must be treated within a few hours or gangrene may result Wear Protective Equipment A Protective clothing and equipment should be worn A Wear clothing and equipment appropriate for the job Avoid loose fitting clothing A Prolonged exposure to loud noise can cause hearing impairment or hearing loss Wear suitable hearing protection such as earmuffs or earplugs A Operating equipment safely requires the full attention of the operator Avoid wearing radio headphones while operating machinery Keep Riders Off Machinery A Riders obstruct the operator s view they could be struck by foreign objects or thrown from the machine A Never allow children to operate equipment 3 17 08 DT55 amp DTM55 Powered Ditchers 324 053M 3 Table of Contents L
28. placeable 3 8 thick skid shoe for long life and uniform depth control Material control chute allows the operator to place material just outside the tractor path to as far away as the Ditcher will throw it Control the throwing distance by raising or lowering the chute with either a 2 x 8 hydraulic cylinder or ratchet jack Depth control wheel optional Ripper shank optional 16 5 x 6 50 8 Pneumatic gauge wheel keeps digging depth constant from just skimming the ground to 10 deep For hard packed soils the Shank rips up the ground just ahead of the impeller allowing the impeller to take in the soil vs bouncing on hard packed soil Shank has 3 height adjustments from cutting edge depth to 5 below cutting edge 3 17 08 DT55 amp DTM55 Powered Ditchers 324 053M 21 Table of Contents Section 7 Troubleshooting Problem Cause Solution Driveline Vibrates Worn Universal Joint Replace Universal Joint Cutting Depth Insufficient Machine carried by tractor Lower 3 Point arms 3 Point top link too long Shorten top link Ground hard enough to require Install Ripper Ripper Depth control set too low Adjust to depth required Skid Shoe or Gauge Wheel Rotor will not turn Driveline not engaged Engage driveline Shear bolt in clutch broken Replace shear bolt in clutch Chain separated in case Repair drive chain Excessive noise in chain Chain loose Adjust spring idler tension case S
29. procket to chain alignment Adjust sprocket to chain alignment Spring loose from idler Re Hook spring to idler amp adjust Ground cut insufficient Worn cutting edges Rotate or replace cutting edges 22 DT55 amp DTM55 Powered Ditchers 324 053M 3 17 08 Land Pride Section 8 Appendix Bolt Size Inches 1 4 20 Table of Contents 1 4 28 11 T T 5 16 18 17 11 EE frre fs efor or TE 1 27 a 42 I z 32 67 7 F 3 8 zne 20 fa9 fse rs ss fios re M10 X 1 5 33 24 39 29 58 42 M10 X 0 75 Me a a a 105 7 16 14 1 2 13 68 9 105 145 105 1 2 20 115 165 120 T 150 I aer ee 9 16 12 210 155 5 8 130 me 150 M12 X 1 75 a 105 145 x z 155 115 oe 160 5 8 18 150 a 170 170 a ae a T 7 3 4 10 235 265 165 155 115 4240 hi E T E T 195 145 4310 185 z 5 250 z ET 7 220 165 350 a w 665 1050 780 z T T 7 3 1150 845 M30xs 5 960 f7o5 1510 1120 2100 1550 1 1 8 E T 795 1750 a 1210 890 1960 1440 T oe 1520 1120 2460 1820 1 1 8 1 1 4 1 3 8 K 890 an 1990 1470 3230 2380 1010 745 2270 1180 870 2640 1 3 8 1670 3680 2710 11 2 6 1950 4290 3160 1060 785 1680 1240 2320 1710 1730 1270 2650 1950 3660 2700 1880 1380 2960 2190 4100 3220 1 in tpi nominal thread diameter in inches threads per inch 2 N m newton met
30. r driveline half f Remove all burrs and cuttings Driveline Maximum Allowable Length Be sure to check driveline minimum length before checking driveline maximum allowable length Refer to Figure 1 3 Driveline maximum allowable length when fully extended must have a minimum overlap of profile tubes by not less than 1 2 the free length with both inner and outer profile tubes being of equal length 24804 A FREE LENGTH IMPLEMENT END 1 2 1 2 1 2 OVERLAP ee Er OUTER PROFILE INNER PROFILE TRACTOR END FREE LENGTH MAXIMUM ALLOWABLE LENGTH Outer Shielding has been removed for clarity Driveline Maximum Length Figure 1 3 1 Pull inner and outer profiles apart Measure and record free length of both profiles They should be the same 2 With driveline profiles pulled apart apply multi purpose grease to the inside of the outer profile and reassemble the two profiles 3 Move driveline halves together until profile tubes overlap by 1 2 the free length Measure and record maximum allowable length shown in Figure 1 3 Attach inner driveline yoke to drive shaft and outer driveline yoke to tractor s PTO shaft The driveline should now be moved back and forth to insure that both ends are secured Reattach any end shown in Figure 1 2 that is loose c Attach outer driveline universal joint to tractor PTO shaft and inner driveline universal joint to 3 17 08 DT55 amp DTM55 Powered
31. rication page 18 Check air pressure in gauge wheel tire Refer Section 8 to Tire Inflation Chart for tire pressure page 23 Operating Instructions 1 Operate with 540 rpm PTO tractor on the DT55 and 1000 rpm PTO on the DTM55 2 Engage PTO at approximately 200 RPM and slowly increase to proper PTO RPM 3 Ditching should not be done in wet conditions as soil will stick to the blades and reduce the digging ability of the Ditcher 4 DONOT make sharp turns or attempt to back up while Ditcher is in the ground 5 DONOT engage PTOwith machine in the fully raised position 6 DO NOT drop 3 point hitch Lower the Powered Ditcher slowly to the ground 7 Ground speed should be between 3 and 5 mph for normal conditions Under extreme rocky conditions ground speed may have to be reduced for satisfactory performance In general the slower the ground speed the better job Proper operating depth and ground speed are interrelated and performance of the Powered Ditcher will improve with operator experience 9 Periodically check for foreign objects wrapped around the blades and remove them after disengaging PTO turning off tractor and removing ignition key General Operating Instructions Now that you have familiarized yourself with the Operator s Manual completed the Operator s Checklist and properly attached your Powered Ditcher to your tractor you are almost ready to begin using your Land Pride 55 Se
32. ries Powered Ditcher It is now time to do a running operational safety check If at any time during this safety check if you detect a malfunction in either the Powered Ditcher or tractor shut tractor off immediately remove switch key and make necessary repairs or adjustments before continuing on Make sure the tractor s park brake is engaged the tractor s PTO is disengaged the Powered Ditcher is slightly off of the ground and the power shaft is not ina bind Start the tractor and then back the tractor throttle off until the engine is at low idle With the tractor running at an idle speed make sure if equiped that the optional hydraulically controlled material deflector chute is operating properly for on the go adjustment with the tractor s hydraulic controls This is also the time to make sure that the rear hydraulic control arms will lower the Powered Ditcher from transport to working position and back without putting the power shaft into a bind Again lift the Powered Ditcher slightly off of the ground and raise the engine rpm slightly Engage the PTO drive and check to make sure everything is running smoothly If not safely shut the tractor down and make the necessary corrections If everything is in proper working condition you are ready to move to the work site You should inspect the area where you intend to work making sure that there are no obvious debris large rocks or other materials that are in your working path
33. rn or scratched to prevent rust Aerosol touch up paint is available from your Land Pride dealer Order Land Pride part 821 002C for Black or 821 011C for beige Store Ditcher in a clean dry place Drive Chain Maintenance The operator should check periodically to make sure that the drive chain is tight If adjustment is needed refer to Drive Chain Adjustment on page 14 16 DT55 amp DTM55 Powered Ditchers 324 053M 3 17 08 Land Pride Section 4 Maintenance amp Lubrication Drive Sprocket and Drive Chain Replacement Refer to Figure 4 1 1 Remove top cover plate 1 and rear inspection plate 2 Loosen jam nut 14 and idler adjustment bolt 10 Roll master link 23 in dual 80 roller chain to top center and remove Remove chain by pulling chain from the top IMPORTANT Loctite is required on all installed bolts and silicone is required on all installed gaskets Replace idler sprockets 22 by removing tightener assembly 3 from inside the chain case a Unscrew 3 8 nuts 15 and remove tightener assembly 3 b Remove cap screw 9 spacers 5 amp 6 and sprockets 22 Keep cap screw and spacers for reuse c Install new sprockets 22 by inserting 3 4 10 x 3 1 2 GR5 hex head cap screw threw idler bracket 3 spacer 6 sprocket 22 sprocket spacer 5 sprocket 22 spacer 6 and out through idler bracket 3 Secure with lock nut 13
34. shaping terraces and grader ditches See Features and Benefits Section 6 for additional information Using This Manual e This Operator s Manual is designed to help familiarize you with safety assembly operation adjustments troubleshooting and maintenance Read this manual and follow the recommendations to help ensure safe and efficient operation e The information contained within this manual was current at the time of printing Some parts may change slightly to assure you of the best performance e To order a new Operator s or Parts Manual contact your authorized dealer Manuals can also be downloaded free of charge from our website at www landpride com or printed from the Land Pride Service amp Support Center by your dealer Terminology Right or Left as used in this manual is determined by facing the direction the machine will operate while in use unless otherwise stated Definitions NOTE A special point of information that the operator must be aware of before continuing IMPORTANT A special point of information related to its preceding topic Land Pride s intention is that this information should be read and noted before continuing Owner Assistance The Warranty Registration card should be filled out by the dealer at the time of purchase This information is necessary to provide you with quality customer service If customer service or repair parts are required contact a
35. size drainage or irrigation ditch 6 Blades on impeller 6 Blades make digging easier and smoother than fewer blades 3 8 Blades 3 8 Hardened cutting edge Heavy duty blades for long life Impeller blades feature a replaceable hardened edge to take on rough and rocky conditions Easier and more cost effective to replace edge vs using hard faced material on impeller Double 80 chain Spring loaded chain idler Double 80 high tensile roller chain keeps stretching to a minimum and has the strength needed to take shock loads posed by extreme digging conditions Chain idler is spring loaded to keep constant tension on chain during tough digging conditions which also makes for smoother digging operations Hardened tooth sprockets 2Greasable flange bearings Hardened tooth sprockets have the strength needed to take the load of the double 80 chain and rigorous digging conditions Input and output shafts feature 2 1 4 ID ball type bearings Ball bearings offer smooth and quiet operation Bearings are greasable to keep properly lubricated and purge dirt out 4 Bolt cast iron flanges Cat 5 Shear bolt driveline Bearings are housed in a heavy duty 4 bolt cast iron flange Heavy duty casting offers full protection under extreme use Heavy duty driveline with shear bolt protects the unit when obstructions are encountered Depth controlling skid shoe optional Material control chute optional Re
36. ther is any liability assumed for damages resulting from the use of the information contained herein Land Pride reserves the right to revise and improve its products as it sees fit This publication describes the state of this product at the time of its publication and may not reflect the product in the future Land Pride is a registered trademark All other brands and product names are trademarks or registered trademarks of their respective holders Printed in the United States of America DT55 amp DTM55 Powered Ditchers 324 053M 3 17 08 Land Pride Important Safety Information Table of Contents These are common practices that may or may not be applicable to the products described in this manual Safety at All Times Thoroughly read and understand the instructions given in this manual before operation Refer to the Safety Label section read all instructions noted on them Do not allow anyone to operate this equipment who has not fully read and comprehended this manual and who has not been properly trained in the safe operation of the equipment A Operator should be familiar with all functions of the unit A Operate implement from the driver s seat only A Make sure all guards and shields are in place and secured before operating the implement A Do not leave tractor or implement unattended with engine running A Dismounting from a moving tractor could cause serious injury or death A Do not sta
37. y the end user 3 17 08 DT55 amp DTM55 Powered Ditchers 324 053M 25 Corporate Office PO Box 5060 Salina Kansas 67402 5060 USA www landpride com
Download Pdf Manuals
Related Search