La Crosse Technology WT-5432 User's Manual
Contents
1. 3 In addition to or instead of inserting batteries the AC adapter can be used Simply insert the adapter into the N gt receptacle on the underneath of the alarm clock and then plug the adapter into the wall socket 4 Replace the battery cover The projector will activate and remain on if the alarm clock is plugged in If only batteries are used the projector will only be activated when a button is pressed The projection is a red light not harmful under normal usage although care should be taken to not look directly into the light Note After the batteries have been installed a tone will sound and the LCD Liquid Crystal Display will activate The indoor temperature and the remote temperature will be displayed within three minutes Also the time will appear as The WWVB search is automatically initiated and a tower icon appears and flashes with the time colon no tower icon will appear if the WWVB is too weak to be detected and the time display will remain on While 4 the WWVB search is being conducted various numbers will appear in the time display After 10 minutes the projection alarm will either display the WWVB time or discontinue the search if the time is not found If the search is cancelled will remain in the time LCD The projection alarm will conduct a WWVB search every hour until the first signal is found Once the WWVB time is found a search is a2. Press and release the button to select the appropriate time zone There are 13 time zones to choose from based relative to the international time standard of GMT Greenwich Mean Time D 4h Atlantic Time 5h Eastern Time default setting 6h Central Time 7h Mountain Time 8h Pacific Time 9h Alaskan Time 10h Hawaiian Time 11h 12h Next two time zones West of HAW Oh Greenwich Mean Time 1h 2h 3h Three time zones West of GMT 4 From 5h to 8h a US map with the highlighted time zone will also be displayed to the right of the time display 5 Press and release the SET button to confirm the time zone setting and to advance to DST Daylight saving time setting DST Daylight Saving Time Setting Note The DST default is On meaning that the WWVB will automatically change the time according to Daylight Saving Time in the spring and fall For areas that do not recognize DST changes Arizona and parts of Indiana turn the DST OFF 1 Press and release the button to turn the DST off as will be indicated by the display of OFF in the time LCD 2 Press and release the SET button to confirm the DST setting and to advance to select the length of the snooze Adjustable Snooze Time Note The snooze length can be adjusted from I minute to 59 minutes This duration refers to the length of time the alarm will be disabled when
3. date remote temperature 1 2 Press and release the MODE button The display will now show month day year remote temperature Press and release the MODE button again and the display will now show seconds remote temperature Press and release the MODE button again and the display will now show alarml time remote temperature Press and release the MODE button again and the display will now show alarm2 time remote temperature Press and release the MODE button again and the display will now show indoor temperature remote temperature Press and release the MODE button again and the display will now show day month date remote temperature IV Mounting the Remote Temperature Sensor The remote temperature sensor can be mounted in two ways 1 with the use of screws 2 using the adhesive tape A Mounting with Screws 1 UR Remove the mounting bracket from the remote temperature sensor The bracket should snap off easily Place the mounting bracket over the desired location Through the three screw holes of the bracket mark the mounting surface with a pencil Where marked start the screw holes into the mounting surface Screw mounting bracket onto the mounting surface Ensure that the screws are flush with the bracket Snap the remote temperature sensor onto the mounted bracket B Mounting with Adhesive Tape 1 With a nonabrasive solution clean and dry the back o
4. minute The time will display PM a H Jp if set to PM and nothing if set to TENDENCY a The projection alarm will revert to normal operation when no buttons are pressed for 15 seconds Activating Deactivating the Alarm a b After entering the alarm setting mode the alarm is activated either ALM1 or ALM2 To toggle between activating and deactivating the alarm press either the ALM1 or ALM2 buttons briefly 1 or 2 will be displayed to the right of the time display when the alarm is activated When the snooze bar is pressed the display will scroll through the alarm 1 and alarm 2 times in the lower left ee the Alarm Off While Sounding While either alarm is sounding press and release the SNOOZE bar to disable the alarm for the set duration See Section II D If the duration is set to 0 the alarm will be disabled for 24 hours After the SNOOZE bar is pressed the lower left will display the time remaining on the snooze The SNOOZE bar may be pressed at any time to restart the snooze duration 11 c To disable the alarm for 24 hours press and release any button other than the SNOOZE bar or projection keys H Changing the Display Mode Day Seconds and Temperature There are six possible display modes to view the day seconds and temperature remote temperature is constantly displayed To change the display starting at the default of day month
5. the SNOOZE bar is pressed If set to 0 activating the snooze will turn off the alarm for 24 hours 1 Press and release the button to advance the snooze time from 0 off to 59 minutes 2 Press and release the SET button to confirm the snooze setting and to advance to manually set the time Time Setting Note When the WWVB signal is found that time will over ride the manually set time 1 Press and release the button to select the hour Note when setting the hour PM will appear to the left of the hour display if it is AM nothing will be displayed 2 3 4 Press and release the SET button to confirm the hour setting and to shift to select the minutes Press and release the button to select the minutes Press and release the SET button to confirm the time setting and to advance to manually set the date G Date Setting Note When the WWVB signal is found that date will over ride the manually set date Ne Press and release the button to select the year Press and release the SET button to confirm the year and to set the month The month will flash Press and release the button to select the appropriate month Press and release the SET button to confirm the month and to set the date The date will flash Press and release the button to select the appropriate date Press and release the SET button to confi
6. Time and Frequency Division WWVB radio station is located in Ft Collins Colorado and transmits the exact time signal continuously throughout the United States at 60 kHz The signal can be received up to 2 000 miles away through the internal antenna in the projection alarm However due to the nature of the Earth s Ionosphere reception is very limited during daylight hours The projection alarm will search for a signal every night when reception is best The WWVB radio station derives its signal from the NIST Atomic clock in Boulder Colorado A team of atomic physicists is continually measuring every second of every day to an accuracy of ten billionths of a second per day These physicists have created an international standard measuring a second as 9 192 631 770 vibrations of a Cesium 133 atom in a vacuum For more information about WWVB please see the NIST website at http www boulder nist gov timefreq stations wwvb htm QUICK SET UP GUIDE Hint Use good quality Alkaline Batteries and avoid rechargeable batteries 1 Have the indoor station and outdoor remote 3 to 5 apart 2 Batteries should be out of both units for 10 minutes 3 Place the batteries into the outdoor remote first then into the indoor station All outdoor remotes must be started before the indoor station 4 DONOT PRESS ANY BUTTONS FOR 10 MINUTES In this time the display and sensor will start to talk to each other and the display will show both the indoor tempera
7. WT 5432 433 MHz Radio Controlled Projection Alarm Instruction Manual I l I IL RADIO CONTROLLED OUTDOOR TEMP TENDENCY PROJECTION LA CROSSE vok and technology TECHNOLOGY for home and office TABLE OF CONTENTS Topic Page Inventory of Contents Additional Equipment 3 About WWVB 3 Quick Set Up Guide 4 Detailed Set Up Guide Battery Installation 5 6 Program Mode Programming Sequence 6 Function Buttons 6 Time Zone Setting 6 7 DST Daylight Saving Time Setting 7 Adjustable Snooze 7 Time Setting 8 Date Setting 8 12 24 Hour Setting Selecting F or C 8 Features amp Operations Features 9 Radio Controlled Time 9 Projection of time and or remote temperature 10 Forecast Icon 11 EL Backlight 11 Indoor Temperature 12 Remote Temperature 12 Time Alarm 13 Changing Display Mode viewing seconds 14 Mounting 15 Maintenance amp Care 16 Troubleshooting 17 Specifications 18 Warranty and Contact Information 19 20 INVENTORY OF CONTENTS 1 WT 5432 projection alarm 2 TX6U remote temperature sensor 3 AC adapter transformer 6V 4 Instruction manual and warranty card ADDITIONAL EQUIPMENT not included 1 Three fresh 1 5V AA batteries optional for alarm clock 2 Two fresh 1 5V AA batteries for remote transmitter ABOUT WWVB Radio Controlled Time The NIST National Institute of Standards and Technology
8. an AC outlet the projection alarm can continuously project the time and or remote temperature When operating on batteries alone the projection alarm will only project when a button is pressed The projection will auto focus for display from three to six feet away A dark surrounding will be necessary to clearly see the projection The default is projecting time Hour and Minutes The projection alarm can be se to project the time MO remote temperature M1 or alternating 8 12 13 14 between time and remote temperature M2 by pressing the DISPL button The selected display mode will flash on the lower left as MO M1 or M2 The direction of the display can also be rotated 360 in 90 increments by pressing the directional button There is no display on the LCD that signifies the direction The projector case can be rotated 180 to further help orient the projected display The intensity of the projection can be adjusted to three different settings as well as turned off by pressing the light Intensity button When turned off the projection will only come on when a button is pressed The intensity cannot be set for the projected display when set to off When only batteries are used the intensity setting is set to off with no other options ALMI HR DSP ALM2 MIN SET 438 MHz MODE Light intensity Display Mode Display Direction C F
9. ature is desired simply mount the remote temperature sensor outside It is recommended to mount the remote temperature sensor on the North side of the house away from sources of heat or cold away from direct sunlight windows vents etc The range of the transmitter is 80 feet in open space While the signal is able to penetrate walls it will decrease the range Concrete and metal structures offer the most resistance 10 The transmitter should not be mounted on a metal surface The transmitter and projection alarm should be kept away from other sources of possible interference including cordless appliances telephones baby monitors microwave ovens and other strong electrical appliances The remote temperature is displayed in F or C depending on the time format 12 or 24 hour mode When in 12 hour format the temperature will be in F When in 24 hour mode the temperature will be in C G Time Alarm The projection alarm has two separate alarms for time ALM1 and ALM2 The alarms have a different sound ALM1 increases in volume after 25 seconds and again after 50 seconds ALM is a constant volume The total duration is 96 seconds for each alarm 1 Setting the Alarm a Press and hold ALM or ALM2 for two seconds until the Alarm 2 activated alarm time is flashing Press and release ALMJ HOUR Q l w to advance the hour and ALM2 MIN to advance the OUTDOOR bes
10. eive a signal due to any source of interference LA CROSSE TECHNOLOGY WILL NOT ASSUME LIABILITY FOR INCIDENTAL CONSEQUENTIAL PUNITIVE OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PROJECTION ALARM THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION THIS PRODUCT IS NOT A TOY KEEP OUT OF CHILDRENS REACH This warranty gives you specific legal rights You may also have other rights specific to your State Some States do not allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you For warranty work technical support or information contact La Crosse Technology 2809 Losey Blvd S La Crosse WI 54601 Phone 608 782 1610 Fax 608 796 1020 e mail support lacrossetechnology com warranty work sales lacrossetechnology com information on other products web www lacrossetechnology com 15 FCC ID OMO 01RX receiver OMO 01TX transmitter THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION 16
11. f the mounting bracket and the mounting surface to ensure a secure hold The mounting surface should be smooth and flat Remove the protective strip from one side of the tape 12 i D Adhere the tape to the designated area on the back of the mounting bracket Remove the protective strip from the other side of the tape Position the remote temperature sensor in the desired location ensuring that the projection alarm can receive the signal V Maintenance and Care A Extreme temperatures vibrations and shock should be avoided to prevent damage to the units B Clean displays and units with a soft damp cloth Do not use solvents or scouring agents they may mark and damage the displays and casings C Do not submerge in water D Immediately remove all low powered batteries to avoid leakage and damage E Replace with new batteries only and of recommended size F Opening the casings invalidates the warranty Do not try to repair the units Contact La Crosse Technology for Repairs TROUBLESHOOTING Problem The projection is faint Solution 1 Change intensity setting 2 Use AC adapter 3 Darken surroundings 4 Use fresh batteries if AC is not used Problem The LCD is faint Solution 1 Replace the batteries Problem OFL appears in the indoor temperature LCD Solution 1 Move unit to an area with warmer or cooler surrounding temperature Current surrounding temperatures are outside measu
12. in Ft Collins Colorado and transmits the exact time signal continuously throughout the United States at 60 kHz The signal can be received up to 2 000 miles away through the internal antenna in the projection alarm Due to the nature of the Earth s Ionosphere reception is very limited during daylight hours The projection alarm will search for a signal every night when reception is best The WWVB radio station receives the time data from the NIST Atomic clock in Boulder Colorado A team of atomic physicists 1s continually measuring every second of every day to an accuracy of ten billionths of a second per day These physicists have created an international standard measuring a second as 9 192 631 770 vibrations of a Cesium 133 atom in a vacuum For more detail visit http www boulder nist gov timefreq htm To listen to the NIST time call 303 499 7111 This number will connect you to an automated time announced at the top of the minute in Coordinated Universal Time which is also known as Greenwich Mean Time GMT This time does not follow Daylight Saving Time changes After the top of the minute a tone will sound for every second It is possible that your projection alarm may not be exactly on the second due to the variance in the quartz However the clock will adjust the quartz timing over the course of several days to be very accurate under 0 10 seconds per day Projection of Time and or Remote Temperature When plugged into
13. n alarm has an EL backlight designed for night viewing This will light up for 2 seconds whenever a button is pressed The EL backlight cannot be turned on constantly as this would drain the batteries and burn out the EL light E Indoor Temperature 1 The projection alarm measures indoor temperature with an internal sensor This temperature is displayed in F or C depending on the time format 12 or 24 hour mode When in 12 hour format the temperature will be in F When in 24 hour mode the temperature will be in C The indoor temperature will take time to adjust to the surrounding temperature as the sensor is inside the case If the remote temperature is placed next to the projection alarm more often than not the temperature will not be exact with one another This is not a defect but simply reflects the difference in measuring methods The remote temperature is designed for changing temperature at a wide range F Remote Temperature 1 The projection alarm comes with a remote temperature sensor When set up properly the projection alarm will receive and display the remote temperature It is important to power up the transmitter first then the projection alarm If batteries are removed in the remote temperature sensor the projection alarm MUST be re set by removing power sources and re starting The remote temperature is measured within the remote temperature sensor and transmitted to the projection alarm If outdoor temper
14. nd of this instructional manual SPECIFICATIONS Temperature Measuring range 32 F to 122 F with 0 2 F resolution indoor 21 8 F to 140 F with 0 2 F resolution outdoor 0 C to 50 C with 0 1 C resolution Checking intervals Every 10 seconds indoor 3 times in 10 minutes for remote temperature Power source AC Adapter included Input 120VAC 60Hz Output DC 6V 100MA Battery type Station 3 x AA 1 5V Alkaline optional Transmitter 2 x AA 1 5V Alkaline Battery life Approximately 12 months depending on projection and backlight use Dimensions L x W x H 5 25 W x 3 5 H x 1 25 L 14 WARRANTY INFORMATION La Crosse Technology provides a 1 year warranty on this projection alarm Contact La Crosse Technology immediately upon discovery of any defects covered by this warranty Before sending the projection alarm in for repairs contact La Crosse Technology for a return authorization Be sure to keep a copy of your receipt for proof of purchase and warranty The projection alarm will be repaired or replaced with the same or similar model We cannot offer refunds of money or credit toward a different unit For service other than a replacement please contact your vendor retailer from where you purchased the unit This warranty does not cover any defects resulting from improper use unauthorized repairs faulty batteries or the projection alarm s inability to rec
15. orecast Icon 1 2 The weather forecasting feature is estimated to be 75 accurate The weather forecast is based solely upon the change of air pressure over time The WT 5432 averages past air pressure readings to provide an accurate forecast creating a necessity to disregard all weather forecasting for 12 24 hours after the unit has been set up reset or moved from one altitude to another i e from one floor of a building to another floor In areas where the weather is not affected by the change of air pressure this feature will be less accurate Weather Icons There are 3 possible weather icons that will be displayed in the FORECAST LCD FORECAST FORECAST cas lt Som Sunny indicates that the weather is expected to improve not that the weather will be sunny Sun with Clouds indicates that the weather is expected to be fair not that the weather will be sunny with clouds 9 Clouds with Rain indicates that the weather is expected to get worse not that the weather will be rainy The weather icons change when the unit detects a change in air pressure The icons change in order from sunny to partly sunny to cloudy or the reverse It will not change from sunny directly to rainy although it is possible for the change to occur quickly If the symbols do not change then the weather has not changed or the change has been slow and gradual D EL Backlight 1 2 The projectio
16. ring range Problem No reception of WWVB signal Solution 1 It may help reception to face the front of the projection alarm in the general direction of Ft Collins Colorado 2 Wait overnight for signal 3 Be sure the projection alarm is at least 6 feet from any electrical devices i e TV sets computers or other radio controlled clocks 4 Remove batteries for five minutes reinsert and leave the unit alone overnight without pressing buttons 5 Try leaving batteries in unit but unplug the AC adapter overnight The first signal is most difficult to receive clearly and even a slight interference may cause failure of WWVB 13 reception 6 If problems persist contact La Crosse Technology Problem Hour is incorrect minute and date are correct Solution 1 Be sure correct time zone and daylight saving time are selected Problem appears in outdoor temperature LCD Solution 1 Check batteries in remote 2 If batteries are replaced in remote the unit must be re started Remove all batteries and then follow start up procedure Problem OFL appears in the outdoor temperature LCD Solution 1 Remote temperature is out of range move closer 2 Check batteries 3 Interference from an outside source cordless telephone etc 4 Contact La Crosse Technology Note For any questions not answered contact La Crosse Technology with the contact information found at the e
17. rm the date and to set the weekday The weekday will flash Press and release the button to select the appropriate weekday Press and release the SET button to confirm the calendar settings and to advance to select either 12 or 24 hour time display H 12 24 Hour Setting Selecting F or C Note Setting to the 24 hour mode also known as Military Time will also change the temperature to display in C instead of F 1 2 Press and release the button to toggle between 12 and 24 hour time Press and release the SET button to confirm the 12 24 hour time display and to return to normal operation HI Features and Operations A Features bor eit ata Radio controlled time and date Projection of time and or remote temperature Forecast icon based on changing air pressure EL backlight 7 OID Ra 1 10 Six modes of date seconds temperature display Indoor temperature Remote outdoor temperature Dual alarms Adjustable snooze dio Controlled Time and Date The projection alarm will automatically search for the time signal upon initial set up and every night When the signal is being received there will be a tower icon flashing to the left of the time display When the time signal has been received successfully the tower icon will remain steady until midnight The NIST National Institute of Standards and Technology Time and Frequency Division WWVB radio station is located
18. ture and an outdoor temperature If the station does not display both temperatures after the 10 minutes please retry the set up as stated above After both indoor and outdoor temperatures are displayed for 10 minutes you can place your sensor outdoors and set your time The remote sensor should be placed in a dry shaded area The remote sensor has a range of 80 feet Any walls that the signal will have to pass through will reduce distance An outdoor wall or window will have 20 to 30 feet of resistance and an interior wall will have 10 to 20 feet of resistance Your distance plus resistance should not exceed 80 ft in a Straight line NOTE Fog and mist will not harm your remote sensor but direct rain must be avoided To complete the set up of your temperature station after the 10 minutes have passed please follow the steps starting on page 6 DETAILED SET UP GUIDE Important Insert batteries into the transmitter first then into the alarm clock Do not press any buttons until remote temperature is displayed I BATTERY INSTALLATION A Remote Temperature Sensor 1 Remove the battery cover vt 2 Observing the correct polarity install 2 AA batteries J O 3 The batteries will fit tightly to avoid start up c problems make sure that they do not spring free during installation 4 Replace the battery cover B Projection Alarm Remove the battery cover 2 Observe the correct polarity and install 3 AA batteries
19. utomatically conducted nightly at midnight If the signal is found at midnight the tower icon will remain If the signal is not found another search will take place every hour until 6 00 am until the signal is found successfully If no signal is found during this period the tower icon will not appear and the clock will search again at 12 00 am the next night Il Program Mode To enter the program mode hold down the SET button for 1 second until the time zone 5 which is the default setting flashes in the lower left Press and release the SNOOZE button at any time to exit the program mode or wait approximately 15 seconds for the projection alarm to automatically return to normal operation A Programming Sequence 1 Time Zone Setting Aes 2 Daylight Saving Time ON OFF sani SewrnorcEn 3 Adjustable Snooze 4 Hour Setting ic JH 5 Minute Setting 2 6 Year Setting q 7 Month Setting ae EA AEE T pap ECTON 8 Date Setting s 9 Day Setting 10 12 24 hour Mode B Function Buttons There are 7 function buttons located on the front of the projection alarm and one on the top The function buttons are labeled ALMI HOUR ALM2 MIN light intensity icon DISPL light direction icon SET MODE and SNOOZE the top bar C Time Zone Setting 1 Hold down the SET button for 1 second 2 The time zone 5 default will flash in the Date LCD 3
Download Pdf Manuals
Related Search