La Crosse Technology WS-9117U User's Manual
Contents
1. North facing wall The sending range is 80ft obstacles such as walls concrete and large metal objects will reduce the range Place both units in their desired location before permanently mounting A REMOTE TEMPERATURE SENSOR 1 Remove the mounting bracket from the remote temperature sensor 2 Mount using either screws or adhesive tape 3 Reattach the remote temperature sensor to the mounting bracket B THE TEMPERATURE STATION 1 The indoor temperature station comes with the table stand already mounted If you wish to use the table stand all 17 that is required is to place the indoor temperature station in an appropriate location 2 To wall mount remove the table stand To do this pull down on the stand from the rear and rotate forward a Fix a screw not included into the desired wall and place the indoor temperature station onto the screw using the hanging hole on the backside Gently pull the indoor temperature station down to lock the screw into place 18 TROUBLESHOOTING NOTE For problems not solved please contact La Crosse Technology via e mail or phone or visit our website www lacrossetechnology com Problem The LCD is faint Solution Replace batteries Problem No outdoor temperature is displayed Solution 1 Remove all batteries reinsert into remote temperature sensor first and then into the indoor temperature station 2 Place remote temperature sensor closer to the indoor te2. SET CH button once 2 Degree Fahrenheit will now show a To change between Fahrenheit and Celsius press and release the MIN MAX button When you have your choice shown on the display press and release the SET CH button once 3 An hour will now be flashing a Press and release the MIN MAX button until the correct hour is shown Note When in the 12h mode there is PM displayed under the word TIME when in the PM hours During the AM hours this area will be blank b When the correct hour is shown press and release the SET CH button once 4 A minute will now be flashing a Press and release the MIN MAX button until the correct minutes are displayed Press and release the SET CH button once more and you are done DETAILED SETUP GUIDE I BATTERY INSTALLATION A REMOTE TEMPERATURE SENSOR 1 Remove the mounting bracket 2 Remove battery cover 3 Observing the correct polarity install 2 AA batteries make sure they do not spring free or start up problems may occur Replace cover B INDOOR TEMPERATURE STATION Note After the batteries are installed DO NOT press any buttons This may interfere with the signals causing temperatures to register incorrectly 1 Remove the battery cover on the backside 2 Observing the correct polarity install 2 AAA batteries 3 Replace battery cover 4 Wait 15 minutes p A before pre
3. owner of the product to a USA address only Your La Crosse Technology Ltd warranty covers all defects in material and workmanship with the following specified exceptions 1 damage caused by accident unreasonable use or neglect including the lack of reasonable and necessary maintenance 2 damage occurring during shipment claims must 24 be presented to the carrier 3 damage to or deterioration of any accessory or decorative surface 4 damage resulting from failure to follow instructions contained in your owner s manual 5 damage resulting from the performance of repairs or alterations by someone other than an authorized La Crosse Technology Ltd authorized service center 6 units used for other than home use 7 applications and uses that this product was not intended or 8 the products inability to receive a signal due to any source of interference This warranty covers only actual defects within the product itself and does not cover the cost of installation or removal from a fixed installation normal set up or adjustments claims based on misrepresentation by the seller or performance variations resulting from installation related circumstances LA CROSSE TECHNOLOGY LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL CONSEQUENTIAL PUNITIVE OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION THIS PRO
4. BUTTONS FOR 15 MINUTES In this time the indoor temperature station and remote temperature sensor will start to talk to each other and the display will show both the indoor temperature and an outdoor temperature If the indoor temperature station does not display both temperatures after the 10 minutes please retry the set up as stated above After both indoor and outdoor temperatures are displayed for 15 minutes you can place your remote temperature sensor outdoors and set your time The remote temperature sensor should be placed in a dry shaded area The remote temperature sensor has a range of 80 feet Any walls that the signal will have to pass through will reduce distance An outdoor wall or window will have up to 20 feet of resistance and an interior wall will have up to 10 feet of resistance Your distance plus resistance should not exceed 80 ft in a straight line NOTE Fog and mist will not harm your remote temperature sensor but direct rain must be avoided To complete the set up of your indoor temperature station after the 15 minutes have passed please follow the steps below 1 Press and hold the SET CH button for 5 seconds Note A 12h or 24h will appear to the left of the time 12h for AM PM 24h for military time a To change between 12h and 24h press and release the MIN MAX button When you have your choice shown on the display press and release the
5. DUCT IS NOT A TOY KEEP OUT OF CHILDREN S REACH This warranty gives you specific legal rights You may also have other rights specific to your State Some States do no allow the exclusion of 25 consequential or incidental damages therefore the above exclusion of limitation may not apply to you For warranty work technical support or information contact La Crosse Technology 2809 Losey Blvd S La Crosse WI 54601 Phone 608 782 1610 Fax 608 796 1020 e mail support lacrossetechnology com warranty work sales lacrossetechnology com information on other products web www lacrossetechnology com FCC DISCLAIMER This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 26 Freq 433 92 MHz La Crosse Technology Made in China WS 9117U FCC ID OMO 01RX Receiver OMO 01TX sensor THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION 27
6. North America and only to the original purchaser of this product To receive warranty service the purchaser must contact La Crosse Technology Ltd for problem determination and service procedures Warranty service can only be performed by a La Crosse Technology Ltd authorized service center The original dated bill of sale must be presented upon request as proof of 23 purchase to La Crosse Technology Ltd or La Crosse Technology Ltd s authorized service center La Crosse Technology Ltd will repair or replace this product at our option and at no charge as stipulated herein with new or reconditioned parts or products if found to be defective during the limited warranty period specified above All replaced parts and products become the property of La Crosse Technology Ltd and must be returned to La Crosse Technology Ltd Replacement parts and products assume the remaining original warranty or ninety 90 days whichever is longer La Crosse Technology Ltd will pay all expenses for labor and materials for all repairs covered by this warranty If necessary repairs are not covered by this warranty or if a product is examined which is not in need or repair you will be charged for the repairs or examination The owner must pay any shipping charges incurred in getting your La Crosse Technology Ltd product to a La Crosse Technology Ltd authorized service center La Crosse Technology Ltd will pay ground return shipping charges to the
7. WS 9117U Wireless 433 MHz Temperature Station Instruction Manual LA CROSSE technology tools TECHNOLOGY for home amp office TABLE OF CONTENTS Topic Inventory of Contents Quick Setup Detailed Setup Guide an Battery Installation Setting the Time Selecting Units of Measurement 8 Features 3 1 Resetting Minimum and 13 14 Maximum Temperatures Minimum and Maximum 1 Temperatures Additional remote 14 16 temperature sensors optional Mounting Troubleshooting Maintenance and Care Specifications Warranty Information 24 28 INVENTORY OF CONTENTS 1 The indoor temperature station Figure 1 2 The remote temperature sensor TX6U and mounting bracket Figure 2 3 3 each 1 2 Philips screws 4 One strip of double sided adhesive tape 5 Instruction Manual and Warranty Card Figure 1 Figure 2 ADDITIONAL EQUIPMENT not included 1 1 Philips screwdriver 2 2 Fresh AAA 1 5V batteries 3 2 Fresh AA 1 5V batteries QUICK SETUP Hint Use good quality Alkaline Batteries and avoid rechargeable batteries 1 Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart 2 Batteries should be out of both units for 10 minutes 3 Place the batteries into the remote temperature sensor first then into the indoor temperature station All remote temperature sensors must be started before the indoor temperature station 4 DO NOT PRESS ANY
8. ents or scouring agents they may mark the displays and casings e Do not submerge in water e Do not subject the units to unnecessary heat or cold by placing them in the oven or freezer e Opening the casings invalidates the warranty Do not try to repair the unit Contact La Crosse Technology for repairs 21 SPECIFICATIONS Transmitting 433MHz Frequency Measuring Temperatures Indoor 32 F to 140 F with 0 2 F Temperature resolution Station Indoor 0 C to 69 0 C with 0 1 C resolution 21 8 F to 156 2 F with 0 2 F resolution 29 9 C to 69 0 C with 0 1 C resolution 1 F_ 4 5 C Transmitting Maximum 80 feet 25m range open space Temperature check Indoor Every 10 seconds Outdoor Two times in 10 minutes Batteries Alkaline recommended Remote 2x AA 1 5V Temperature Sensor Indoor Indoor Temperature Station Outdoor Temp accuracy 2 x AAA 1 5V 22 Temperature Station Dimensions H x W x D Indoor 5x 2 25 x lin Temperature excluding table stand Station 125 x 58 x 23 mm Remote 5x 15x lin Temperature 128 x 40 x 23 mm Sensor Battery life Approximately 1 year WARRANTY INFORMATION La Crosse Technology Ltd provides a 1 year limited warranty on this product against manufacturing defects in materials and workmanship This limited warranty begins on the original date of purchase is valid only on products purchased and used in
9. is not done correctly and if the total time for set up exceeds 6 minutes 2 It is necessary to remove the batteries from all units currently in operation 3 Remove the battery covers to all remote temperature sensor units 4 Place all remote temperature sensor units in a numeric sequential order 5 In sequential order install batteries follow the same battery installation procedures seen in section I of the Detailed Set Up Guide 6 Install batteries into the indoor temperature station 7 Follow the Detailed Set Up Guide for programming and operating instructions 15 D VIEWING AND OPERATING WITH MULTIPLE REMOTE TEMPERATURE SENSOR UNITS 1 To view the temperature of a different remote temperature sensor unit press and release the SET CH button A shift from one boxed number to the next should be observed in the OUTDOOR LCD 2 To view the Minimum Maximum temperature first select from which remote temperature sensor to read data indicated by the boxed number Pressing and releasing the MIN MAX button will toggle through the minimum and maximum indoor temperature and the minimum and maximum outdoor temperature 3 To reset the Minimum Maximum readings press and hold the MIN MAX button for four seconds 16 V MOUNTING Note To achieve a true temperature reading avoid mounting in direct sunlight We recommend that you mount the remote temperature sensor on an outside
10. mperature station 3 Be sure all batteries are fresh 4 Place remote temperature sensor and indoor temperature station in position so the straight line signal is not passing through more than two or three walls 19 Problem Temperatures do not match if units are placed next to each other Solution Each temperature sensor is manufactured to be accurate to within 1 degree plus or minus and under normal conditions so two temperature sensors could be as much as 2 degrees different However the difference can be exaggerated further because the temperature sensors are designed for different working environments The indoor sensor is less responsive to ambient air currents because of the shielding effect of the display s case In addition the case can act as a heat sink to absorb and store heat from external sources i e handling of the case or radiant heat In addition the much greater range of the outdoor temperature sensor requires a different calibration curve than the indoor range Error is usually greater at the extreme ends of a range making it harder to compare different ranges with different curves Under non laboratory conditions it is difficult to compensate for the above factors and obtain an accurate comparison 20 MAINTENANCE AND CARE INSTRUCTIONS e Extreme temperatures vibration and shock should be avoided to prevent damage to the units e Clean displays and units with a soft damp cloth Do not use solv
11. ssing any buttons i 10 5 The indoor temperature station should now show in the er TIME LCD and EH temperatures in the Jk INDOOR and 10 OUTDOOR LCD s i 2 II TIME A SETTING THE TIME 1 Press and hold the SET CH button for 5 second 12h will appear in the TIME LCD 2 Press and release the MIN MAX button to select either 12h time am pm or 24h time 3 Press and release the SET CH button 2 times the hour will flash in the upper left corner 4 Press and release the MIN MAX button to set the hours 11 5 Press and release the SET CH button to move to the minute setting 6 Press and release the MIN MAX button to set the minutes 7 Press and release the SET CH button to activate the clock Note When in 12h mode there is only a PM display which appears under TIME If there is no display here it is AM Make sure you set the time accordingly III UNITS OF TEMPERATURE MEASURE A SELECTING UNITS OF MEASUREMENT 1 Press and hold the SET CH button for 5 second until 12h or 24h appears in the TIME LCD 2 Press and release the SET CH button again F will appear in the TIME LCD 12 3 Press and release the MIN MAX button to shift between F and C 4 Press and release the SET CH button twice to activate se
12. ttings IV FEATURES A MINIMUM AND MAXIMUM TEMPERATURES 1 Press and release the MIN MAX button MIN appears in the temperature LCD s and the recorded minimum temperatures are displayed 2 Press and release the MIN MAX button to toggle to the maximum temperatures The time of occurrence of the value for outdoor temperature will also flash B RESETTING THE MINIMUM AND MAXIMUM TEMPERATURES 1 To reset both the minimum and maximum temperatures press and hold the RESET button for 4 13 seconds C ADDING ADDITIONAL REMOTE TEMPERATURE SENSORS OPTIONAL 1 The WS 9117U is able to receive signals from 3 different remote temperature sensors Following are some brief instructions for the basic set up of remote temperature sensor units with the WS 9117U These extra sensors can be purchased through the same dealer as this unit or by contacting La Crosse Technology directly A TX6 will monitor temperature only a TX3U will monitor temperature and display the temperature on its LCD and the TX3UP will monitor the temperature via a probe for use in pools spas etc Note When setting up multiple units it is important to remove the batteries from all existing units in operation then to insert batteries first into all the 14 remote temperature sensor units and in numeric sequence Second install batteries into the indoor temperature station Transmission problems will arise if this
Download Pdf Manuals
Related Search