KoldFront KIM202W User's Manual
Contents
1. unit should be located on a firm and level surface that is able to support the ice maker s total weight with water There must be at least 4 inches of space around the back and sides of the unit for proper air circulation Water Requirements Only use potable water or water suitable for drinking temperature of the water should be between 51 and 90 F e Change the water in the water reservoir every 24 hours to ensure a reasonable hygiene level Note The add water light uses an electronic sensor that may not detect purified filtered reverse osmosis or distilled water You may need to add a pinch of salt to the water to increase the mineral content Electrical Requirements Read all safety precautions listed at the beginning of this manual It is recommended that a separate circuit serving only your ice maker be provided Use receptacles that cannot be turned off by a switch or pull chain The ice maker is equipped with a power supply cord having a 3 prong grounding plug To minimize possible shock hazard the cord must be plugged into a mating 3 pronged and grounding type wall receptacle providing 110 120V 60Hz grounded in accordance with the National Electrical Code and local codes and ordinances If a mating wall receptacle is not available it is the personal responsibility of the customer to have a properly grounded 3 prong wall receptacle installed by a certified electrician IMPORTANT Discard th2. 5 aee e ee a ea ae eda aee a 1 PARTS IDENTIFICATION ii ccstcccceccccecet 2 QUTER VIEW aaa e an g na ai 2 INSIDE VIEW uriia nyiyani a aa Mae ai eee 2 BEFORE YOU BEGIN PREPARING THE ICE MAKER FOR USE 3 UNPACKING THE ICE 3 CLEANING THE ICE MAKER 4 4 24 41 1 11 4441 410001 3 INSTALLATION REQUIREMENTS ccccccceeeeeeseeeeeeeeceeeeecaaeeeeaaeeeeeeeseaeeesaaeeeeaaeseeeeeeeas 3 Clearance and Environment 1 2 10 0 000000000040 3 Water ROQUIFCINGIIS adinan 3 Electrical Re guir me mS aoig a oa r 3 OPERATIONS a ct eee macerated 4 USING YOUR ICE MAKER si iiaii iaaa dadina iaia 4 USING THE GONTROL PANEL 2 5 a ANa aA REAA in iena taraia aade i naai 5 ice SIZE Selot 5 HOW THE PORTABLE ICE MAKER PRODUCES 2 2 4 4 1 4 00 6 DRAINING THE UNIT aerae 6 NORMAL SOUNDS A 6 CLEANING AND 7 TROUBLESHOOTING
3. or exchange the defective product with a new refurbished or remanufactured product If a product is replaced it will carry the remaining warranty of the original product After the ninety 90 day period EdgeStar will no longer be responsible for labor charges incurred All defective products and parts covered by this warranty will be repaired or replaced on a mail in basis to an EdgeStar authorized repair facility PARTS For a period of ONE 1 YEAR from the date of original purchase EdgeStar will supply new rebuilt or refurbished parts free of charge EdgeStar may request a defective part be returned in exchange for the replacement part All replacement parts or products will be new remanufactured or refurbished All products and parts replaced by EdgeStar under warranty service become the property of EdgeStar This warranty applies to the original purchaser only and only covers defects in workmanship experienced during operation of the product under normal service maintenance and usage conditions This warranty applies to the purchase and use of this product in residential settings within the United States of America WHAT IS NOT COVERED The following limitations apply to the coverage of this warranty This warranty does not cover e Labor charges for installation setup or training to use the product e Shipping damage and any damage caused by improper packaging for shipment to an authorized service center and any damaged caused by
4. 8 SPECIFICATIONS weiss feos cc 9 22 200 0 10 This owner s manual is provided for reference use only Specifications change without prior notice Refer to the product label on the back of your ice maker for the latest technical information Introduction Thank you for purchasing this KoldFront ice maker We are glad you chose us We believe that your purchase of this product opens a relationship between you and KoldFront We will provide the customer support needed to nurture that relationship This manual contains important information regarding the proper installation use and maintenance of your ice maker Following this manual will ensure that your product will work at its peak performance and efficiency Please save the original product packaging in case you need to safely transport your portable ice maker For Your Records Please write down the model number and serial number below for future reference Both numbers are located on the ratings label on the back of your unit and are needed to obtain warranty service You may also want to staple your receipt to this manual as it is the proof of your purchase and is also needed for service under your warranty Model Number Serial Number Date of Purchase To better serve you please do the following before contacting custo
5. corresponds to small ice while the L indicator light corresponds to large ice WARNING Do not tip the unit over while there is water in the reservoir KoldFront Portable Ice Maker How the Portable Ice Maker Produces Ice After the unit is powered on the ice maker begins with rotating the ice case into a horizontal water fill position under the evaporator The water pump is engaged and fills the ice case with water Water overflows for a few seconds before the compressor turns on The compressor then pumps refrigerant and the fan will turn on automatically after the condenser heats up The unit will be producing bullet shaped ice around the stainless steel evaporator When the batch of ice has been fully formed the ice maker stops the freeze cycle and begins the harvest cycle A valve opens diverting hot refrigerant gas into the evaporator The gas heats the evaporator causing the ice cube bullets to slide off the evaporator The ice shovel will automatically push the newly formed ice into the ice basket and will move the ice case back into the water fill position for the next batch of ice The ice maker will produce ice until ice reaches the ice full sensor or until the unit is out of water The ice bin compartment is insulated but not refrigerated and the ice in the bin will slowly melt and the water will be reused Once enough of the ice has melted the ice maker will automatically start making more ice Draining the unit Fol
6. of your unit free This unit is not intended to be used by children and should be supervised to ensure that they do not play with this product Never allow children to crawl inside the ice maker Do not use this appliance near flammable gas or combustibles such as gasoline benzene thinner etc Do not place the unit near heat sources such as ovens and grills Only use in an upright position on a flat level surface and provide proper ventilation Discard the first batch of cubes produced by the ice maker If the unit has not been used for an extended period thoroughly clean it before using it Do not leave any cleaning solutions in or on the unit Do not use solvent based cleaning agents or abrasive solutions on the interior as they may transmit taste to the ice cubes and damage the interior Do not clean the unit with flammable fluids The fumes can create a fire hazard or cause an explosion Other than water do not use other types of liquid to make ice This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities unless they have been given supervision or instruction concerning the use of the appliance by the person s responsible for their safety KoldFront Portable Ice Maker Table of Contents IMPORTANT SAFETY
7. section of this owner s manual A loud knocking or metallic pinging noise may be caused by a damaged compressor Contact EdgeStar support Unit goes through the ice making process but no ice is produced or ice cubes are very thin and small The room temperature or water may be too hot The unit is designed to work in a room that is above 50 F and below 90 F If the unit is run in a room that is particularly warm such as a sunroom or laundry room please move the unit to a cooler room and try again The fan may not be turning on to cool down the condenser coils Contact EdgeStar support Ice case moves back and forth repeatedly and the water pump does not turn on The unit may have a problem with a micro switch Contact EdgeStar support The Add Water light is on even though the unit is full of water The type of water may not have enough impurities i e distilled reverse osmosis RO purified etc Add a pinch of salt to the water This will add minerals to the water which will allow the unit to detect the water The water filter may be clogged Use a brush with plastic bristles to clean the filter at the bottom of the water reservoir The unit has a strange smell or the ice being produced has an unappealing taste The unit may need to be cleaned Read the Cleaning and Maintenance section of this manual KoldFront Portable Ice Maker Specificati
8. Koldfront Portable Ice Maker KIM202W Owner s Manual Important Safety Information Improper handling can cause serious damage to the KoldFront ice maker and or injury to the user This ice maker is designed for domestic indoor use only Do not use the unit for industrial or commercial use Any other use may invalidate the warranty Please review the ratings label located on the rear panel of the unit for electrical and other technical data related to this unit The unit must be used in a properly grounded wall outlet Please read and follow the safety information listed below to reduce the risk of fire electric shock or injury Electrical Safety Do not exceed the power outlet ratings It is recommended that the ice maker be connected on its own circuit A standard electrical supply 115 V 60 2 that is properly grounded in accordance with the National Electrical Code and local codes and ordinances is required Use outlets that cannot be turned off by a switch or pull chain Always turn the unit off and unplug it from the outlet when cleaning Unplug the unit if it is not going to be used for an extended period of time Do not operate the unit with a power plug that is missing the ground plug a damaged cord ora loose socket Be sure the ice maker is properly grounded Never plug or unplug the unit with wet hands Do not bypass cut or remove the grounding plug Do not use extension cords or power strips with
9. The Power Indicator The ice maker power switch is OFF light should be on Try a different power outlet If the unit works on No Power Power outlet does not work a different circuit you may need to contact a certified electrician to resolve the power issue Insufficient power Hardware malfunction Connect the ice maker on a circuit that is able to provide enough power Check the product label for power requirements Contact EdgeStar support Power and ice size indicators are on but the unit does respond to the control panel The unit is in standby mode and the power light may be blinking on and off Press the On Off button until the Power light turns on and is no longer blinking The circuit board may need to be reset Unplug the unit for one hour Plug the unit in and press the power button If after resetting the unit the control panel does not respond you may have a faulty control panel Contact EdgeStar support Water is leaking out the unit Noise during operation The bottom drain plug is not attached Make sure the drain plug is firmly attached If the drain plug has been lost you may need to contact EdgeStar to purchase a replacement plug An internal hose may have been dislodged or disconnected The unit may not be level Certain sounds are normal Contact EdgeStar support Make sure the unit is level and not at an incline See the Normal Sounds
10. ar authorized representative has confirmed that your product is defective and eligible for warranty service the product must be returned to an EdgeStar repair facility The purchaser is solely responsible for prepaying all shipping related costs to and from the repair facility EdgeStar is not responsible for damage resulting from shipper mishandling or improper packaging Do not return a defective product to the place of purchase Products received without a return authorization number will be refused THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY EXPRESSED OR IMPLIED INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE NEITHER THE MANUFACTURER NOR ITS DISTRIBUTORS SHALL BE LIABLE FOR ANY INCIDENTAL CONSEQUENTIAL INDIRECT SPECIAL OR PUNITIVE DAMAGES OF ANY NATURE INCLUDING WITHOUT LIMITATION LOST REVENUES OR PROFITS OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT TORT OR OTHERWISE SOME STATES DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE KoldFront Portable Ice Maker 10 ront Kold EdgeStar Products Box 81336 Austin TX 78708 1336 Toll Free 1 866 319 5473 Web http www edgestar com E
11. e first batch of ice produced by the portable ice maker CAUTION Direct sunlight may cause the ice full infrared sensor to malfunction If the unit continues to produce ice even though the basket is full you may need to move the unit away from the sunlight KoldFront Portable Ice Maker Operation Using Your Ice Maker Before using your ice maker it is strongly recommended to clean it thoroughly Read and follow the Cleaning and Maintenance section of the manual before proceeding Follow the steps below to start using your ice maker 1 Open the top cover and remove any packaging tape that may be holding down the ice case ice shovel ice basket and ice scoop Remove the ice scoop 2 Remove the ice basket and clean it 3 Clean the water reservoir 4 Pour water into the water reservoir Keep the water level below the MAX water mark 5 Insert the ice basket into the water reservoir 6 Close the lid 7 Plug the ice maker s power plug to a grounded outlet 8 Press the On Off button on the Control Panel 9 Press the Select button on the Control Panel to choose between small and large sized cubes If the room temperature is lower than 60 F it is best to select the small size setting otherwise the ice cubes may stick together The ice making cycle may take up to thirteen minutes for a single batch of ice Notes If the water pump is unable to detect or pump water the unit will stop automaticall
12. improper voltage or any other misuse including abnormal service handling or usage Cosmetic damage such as scratches and dents Normal wear and tear on parts or replacement of parts designed to be replaced e g filters cartridges batteries Service trips to deliver pick up or repair install the product or to instruct in proper usage of the product Damages or operating problems resulting from misuse abuse operation outside environmental specifications uses contrary to instructions provided in the owner s manual accidents acts of God vermin fire flood improper installation unauthorized service maintenance negligence unauthorized installation or modification or commercial use Labor charges incurred 91 days or more after the date of original purchase The use of EdgeStar products in commercial settings Optional accessories attachments and appearance items Products that have been modified to perform outside of specifications without the prior written permission of EdgeStar Products lost in shipment or theft Products sold AS IS or from an unauthorized reseller Products that have had their serial numbers removed or defaced Products with serial numbers that have been invalidated OBTAINING WARRANTY SERVICE If you believe your product is defective contact EdgeStar Customer Support for troubleshooting assistance and warranty service at 1 866 319 5473 Please have your serial number and proof of purchase available Once an EdgeSt
13. low the steps below to drain the unit 1 Carefully move the unit towards a sink or other suitable location for draining 2 Remove the rubber drain plug from the bottom of the water reservoir to drain all the water 3 Firmly install the rubber drain plug into the drain port Normal Sounds Your new ice maker may make sounds that are not familiar to you Most of the new sounds are normal Hard surfaces like the floor walls can make the sounds seem louder than they actually are The following describes the kinds of sounds that might be new to you and what may be making them e The ice case motor will make a whirling noise when the ice case and shovel are moving Rattling noises may be produced from the flow of the refrigerant The compressor may make a pulsating or high pitched sound The compressor may also produce a low tone humming sound Water that is being pumped into the ice case will make trickling dripping or splashing sounds As each cycle ends you may hear a gurgling sound due to the refrigerant flowing e You may hear fan noise and air being forced over the condenser by the condenser fan e During the harvest cycle you may hear the sound of ice cubes falling into the ice basket e If the ice maker is run without water the water pump will make screeching noise Note Do not run the unit without water The icemaker must be thoroughly cleaned if it has been left unused for a long time Follow carefully any i
14. mail service edgestar com Register your product download owner s manuals access additional troubleshooting resources and obtain more information on other great EdgeStar amp KoldFront products on the web at http www edgestar com Product contents and specifications may change without notice Copyright 2009 2010 Living Direct Inc
15. mer service If you received a damaged product immediately contact the dealer that sold you the product Read and follow this instruction manual carefully to help you install use and maintain your ice maker Read the troubleshooting section of this manual as it will help you diagnose and solve common issues Visit us on the web at http www edgestar com to register your product download product manuals and access additional troubleshooting resources and up to date information If you need warranty service our friendly customer service representatives are available via email at service edgestar com or by telephone at 1 866 319 5473 Parts Identification Inside View Cover with Control Panel and Window Ice Case Bowl Evaporator Ice Shovel e Ice Full Sensor 225 Ice Basket ae Ice Scoop Outer View Control Panel Air Outlet KoldFront Portable Ice Maker IMPORTANT Do not remove any safety warning or product information labels from your ice maker Note If the room temperature is lower than 60 F it is best to select the small size setting otherwise the ice cubes may stick together WARNING Do not under any circumstances cut or remove the third ground prong from the power cord Before you Begin Preparing the Ice Maker for Use Before you plug the ice maker in to a power supply be sure to let it stand upright for at least 24 hours
16. nstructions provided for cleaning or use of sanitizing solution Do not leave any solution inside the icemaker after cleaning CLEANING AND MAINTENANCE Periodic cleaning and proper maintenance will ensure efficiency top performance and long life Never use a solvent based cleaning agent These cleaners may transmit taste to the ice cubes or damage and discolor the interior Unplug the unit before cleaning the exterior and interior Before using your ice maker you are strongly recommended to clean it thoroughly This process should clean the unit of any impurities that may have been left behind during the manufacturing process 1 Take out the ice basket 2 Clean the interior with a diluted cleaning solution warm water and a soft cloth DO NOT use any caustic or abrasive solutions Do not clean your ice maker with flammable fluids 3 The outside of the ice maker should be cleaned regularly with a mild detergent and warm water 4 Dry the interior and exterior with a soft cloth If the ice has a strange taste If the ice has an unappealing taste or the unit develops a musty odor try running a few cycles of the ice maker with a mild white vinegar solution or lemon juice Then empty out all the vinegar or lemon juice solution and run a few cycles with plain water to eliminate all traces of the vinegar or lemon juice If you find the bad taste remains after this procedure use a solution of 2 tablespoons of baking soda t
17. o a full water reservoir of water left in the unit overnight to absorb any remaining odors tastes Drain the solution rinse the water reservoir and dry the interior Routine maintenance 1 Take out the ice basket 2 Add a mild cleaning solution mixture to the water reservoir Use a 10 1 ratio of water to either white vinegar or lemon juice 3 Run the ice maker to make a couple of batches of ice at least 2 Discard the ice 4 Drain the cleaning solution from the water reservoir 5 Add fresh water to the water reservoir up to the water level mark 6 Run the ice maker to make a few batches of ice Discard the ice 7 Drain the water 8 Add fresh water to the water reservoir to make ice or dry the interior and exterior with a clean soft cloth to store the machine 9 The ice scoop should be washed regularly Wash it just like any other utensil If the ice maker will not be used for an extended period of time you should unplug the unit from power drain the water from the reservoir and dry the interior with a clean soft cloth not touch the power plug when your hands are wet Never unplug the unit by pulling on the plug TROUBLESHOOTING Before Calling for Service If the unit appears to be malfunctioning the issue could be solved by following the suggestions in the Solution column Issue Possible Cause Solution The ice maker is unplugged Plug the ice maker in l Press the power button
18. ons Description of product Portable Ice Maker Model KIM202W Voltage Frequency AC 115V 60Hz Ice Making rated 1 5 2 0 current Color White Ice Storage capacity 1 5 Ibs capability 26 Ibs day Refrigerant R134a 64g Dimensions l 9 5 W x 14 1 D x 12 9 H Width x Depth x Height Weight 20 3 Ibs Note Technical data and performance information provided for reference only Specifications are subject to change Check the rating label on the ice maker for the most accurate information The actual quantity of ice produced in a 24hour period will vary with room and water conditions Notes on ice storage The ice maker will automatically shut off when the ice bin is full The ice bin compartment is insulated but not refrigerated and the ice in the bin will slowly melt and the water will be reused Once enough of the ice has melted the ice maker will automatically start making more ice Limited Warranty One 1 Year Parts amp Ninety 90 Days Labor This product is warranted by EdgeStar to be free from defective workmanship and materials subject to any conditions set forth as follows WHAT IS COVERED LABOR For a period of NINETY 90 DAYS from the date of original purchase labor will be performed free of charge at an authorized EdgeStar repair facility At its option EdgeStar will repair the product with new or remanufactured parts
19. this unit You may need to contact your electrician if it is necessary to use a longer cord or if you do not have a grounded outlet Do not modify the power cord s length or share the outlet with other appliances If you must use an extension cord use No 14AWG minimum size and rated no less than 1875 watts Do not start or stop the unit by switching the circuit s power on and off If the power cord is damaged it must be replaced by the manufacturer or a qualified technician Never repair the unit while it is plugged in Immediately unplug the unit if it makes strange sounds emits an odor or smoke comes out of it and contact customer service Do not remove any part of the casing unless instructed by an authorized technician You should never attempt to repair the unit yourself Contact EdgeStar Support if the unit needs repair service Do not tip the unit over while it has water in the reservoir General Safety Use at least two people to move and install the ice maker to prevent back and other types of injuries Install the ice maker in a well ventilated area where the ambient temperature is above 50 F and below 90 F This unit is designed to be installed indoors and protected from rain sleet snow etc Do not use your ice maker outdoors Place the ice maker away from direct sunlight and make sure that there is at least 4 inches of space between the back of your unit and wall Keep a minimum distance of 4 inches on each side
20. to allow the compressor s oils to settle Unpacking the Ice Maker Carefully remove the packaging materials Remove any shipping tape and glue from your ice maker before using Do not use sharp instruments rubbing alcohol flammable fluids or abrasive cleaners to remove tape or glue These products can damage the surface of your icemaker Check to make sure the ice basket and ice scoop are included If any parts are missing please contact our customer service Put the ice maker on a level and flat surface away from direct sunlight and other sources of heat such as a stove furnace radiator etc The appliance must be positioned so that the power plug is accessible Cleaning the Ice Maker Follow the Cleaning and Maintenance section to clean the ice maker Installation Requirements The ice maker has been designed for free standing installation which will allow you to install the unit in almost any place you desire provided you level the unit and follow the instructions for clearance water and electrical requirements Clearance and Environment Requirements Choose a well ventilated area with temperatures above 50 F and below 90 F Operation outside these temperatures may result in lowered production or may cause other adverse effects e This unit MUST be installed an area protected from the elements e g wind rain water spray or drips The icemaker should not be located next to ovens grills or other high heat sources
21. y and the Add Water indicator will be lit Add water to the unit and restart the unit by pressing the On Off button twice The ice maker will continue making ice until the ice basket is full When the ice basket is full Ice Full indicator will be lit Ice Full Indicator Add Water Indicator IMPORTANT Do not power on the unit without any water Using the Control Panel 5 ON OFF SELECT Power Indicator Ice Size Indicators PONER Ice Size Button Power Button Button Function ON OFF Powers the unit on or off Changes the ice size between Small and SELECT Large The indicator light will turn on next to the size you set Indicator Function ADD WATER The add water light will turn on if the unit does not have water in the reservoir ICE FULL ice full light will turn if the basket is POWER The power light will be solid green when the unit is powered on 5 5 indicates the unit will produce small ice L The L indicates the unit will produce large ice Power Use the On Off button to turn the portable ice maker on and off The Power Indicator light will be solid green when the unit is in the position If the power light is blinking on and off the unit is in standby mode and indicates the unit is plugged in Ice Size Selector Use the Select button to switch the ice size between small and large The S indicator light
Download Pdf Manuals
Related Search