Klipsch Speaker SB-3 User's Manual
Contents
1. switch off turn down the volume on your electronics and wait ve minutes before restarting the system If you experience a noticeable hum when the SP 1 s subwoofer is connected to your system a system that includes video equipment disconnect the cable television line if present If the hum disappears consult your Klipsch dealer for a ground isolator for the cable line If this does not solve the problem contact your Klipsch dealer for further advise Regardless of your ampli er s rated capacity do not operate the system at the full output highest volume Ampli ers can create extremely high levels of distortion when operated at full output and can damage your loudspeakers Most ampli ers are at full power when the volume control is at or just above the 12 o clock position Position speaker connection wires so that they do not create a trip hazard If you have any questions regarding the installation or connection of your Klipsch Synergy speakers please contact your Klipsch dealer or contact us directly at 800 554 7724 Care and Cleaning of Your Klipsch Synergy Speakers Your speakers have a durable matte vinyl nish that should only require dry dusting or cleaning with a damp cloth Avoid the use of abrasive or solvent based cleaners and harsh detergents Klipsch Synergy Series Technology The Klipsch Synergy Series is a complete matched family of high performance loudspeakers that offers superi2. Enclosure Type Bass re ex via wide are rear ring port Drive Components Two way system using one 1 2 54cm K 101 S neodymium magnet aluminum dome compres sion driver with a 90 x 60 Tractrix Horn and one 6 5 16 51cm K 1075 SB magnetically shielded woofer featuring a polymer housing and IMG cone Net Weight 33 lbs 15kg Height 33 83 82cm Width 8 20 32cm Depth 13 6 34 54cm Cabinet Medium density ber board construction MDF Finish Woodgrain vinyl veneer SF 2 Sensitivity 96dB 1 watt 1 meter Bandwidth 35Hz 20kHz 3dB Nominal Impedance 8 ohms Crossover Frequency 2 8kHz Power Handling 100 watts maximum continuous 400 watts peak Enclosure Type Bass re ex via wide are rear ring port Drive Components Two way system using one 1 2 54cm K 101 S neodymium magnet aluminum dome compres sion driver with a 90 x 60 Tractrix Horn and two 6 5 16 51cm K 1078 SB magnetically shielded woofers featuring a polymer housings and IMG cones Net Weight 38 lbs 17 3kg Height 35 88 9cm Width 8 20 32cm Depth 13 6 34 54cm Cabinet Medium density ber board construction MDF Finish Woodgrain vinyl veneer SP 1 Sensitivity 94dB 1 watt 1 meter Bandwidth 30Hz 20kHz 3dB Nominal Impedance 8 ohms Crossover Frequencies 2 3kHz and 125Hz Power Handling 100 watts maximum continuous 400 watts peak Enclosure Type Tweeter and Mid Bass Sealed Enclosure Type Subwoofer Ba
3. Allow at least 11 2 of clearance space above the top screw Check the vertical orientation of the marked hole locations with a torpedo level before drilling Use a 10 or 12 21 2 3 long pan head wood screw to mount into the wall stud Check the t of the screw head in the keyhole tting before installation as screw head sizes do vary Drill the proper size pilot holes at the marked positions and install the screws into the wall stud Leave the back surface of the screw head protruding about 1 4 inch from the wall surface This will facilitate hooking the keyhole bracket over the screw head with the rubber feet installed The clearance between the wall and the screw head may need to be adjusted to achieve a proper t If a stud is not available use the proper type and weight rating of drywall or masonry anchor appropriate for the wall construction Please consult your dealer custom installer or a building contractor in this situation Do not use the keyhole mounting brackets for ceiling installations How to Connect the Synergy Series Speakers AC POWER SP 1 ONLY Since your SP 1 has an internal subwoofer power ampli er it must be plugged into a nearby AC wall outlet The SP 1 should be unplugged from the AC power with the power switch in the OFF position during hook up and installation To eliminate a tripping hazard all connections should be unplugged from the back panel of the speaker if it is being moved
4. and IMG cones Net Weight 15 lbs 6 78kg Height 6 5 16 5cm Width 18 45 72cm Depth 7 5 19 1cm Cabinet Medium density ber board construction MDF Finish Black matte vinyl SS 1 Sensitivity 94dB 1 watt 1 meter equivalent sound energy Bandwidth 60Hz 20kHz 3dB Nominal Impedance 8 ohms Crossover Frequency 2kHz Power Handling 100 watts maximum continuous 400 watts peak Enclosure Type Sealed Drive Components Two way system using two 1 2 54cm K 101 S neodymium magnet aluminum dome compres sion drivers with 90 x 60 Tractrix Horns and one 5 25 13 3cm K 1076 S woofer featuring a polymer housing and IMG cone Net Weight 8 5 lbs 3 9kg Height 6 75 17 15cm Width 15 38 1cm Depth 6 15 24cm Cabinet Medium density ber board construction MDF Finish Black or white CE This product complies with the essential requirements of EMC direc tives 89 336 EEC and 73 23 EEC inclusive of 93 68 EEC and carries the CE mark accordingly Wall Mounting Install the four rubber stick on bumpers one on each corner of the rear panel of the speaker to provide clearance for the speaker wire between the wall and cabinet This will also prevent the speaker from marring the wall Cut out the template on the back cover of the owner s manual to assist in obtaining proper spacing of the two mounting holes If the template is not available space the mounting screws 49 16 apart on a vertical line
5. 8900 Keystone Crossing Suite 1220 Indianapolis Indiana 46240 1 800 KLIPSCH www klipsch com Make sure you return your warranty card so that we may keep you up to date on new Klipsch products and promo tions As always if you have any questions contact your local authorized Klipsch dealer For your records Model Serial Number Date Purchased Dealer Name 193110 15M1199 O w n e r s Manual amp Wa rranty SP 1 SF 2 SF 1 SB 3 SB 2 SC 1 amp SS 1 L O U D S P E A K E R S CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To reduce the risk of electric shock and re do not remove the cover or back plate of this device There are no user serviceable parts inside Refer repairs to a Klipsch authorized service center AVIS Risque de choc electricque ne pas ouvrir CAUTION The international symbol of a lightning bolt inside a triangle is intended to caution you to uninsulated dangerous voltage within the device s enclosure The international symbol of an exclama tion point inside a triangle is intended to alert you to the presence of important operating maintenance and servicing information in the manual accompanying the device CAUTION To prevent electrical shock match the wide blade of the plug on the power cord to the wide slot on the power outlet and insert fully ATTENTION Pour eviter les chocs electriques introduire la lame la plus large de la che dans la borne correspondante de l
6. Avoid extremely long extension cords of small gauge since they can impair the performance of the subwoofer ampli er and present a potential re hazard If the SP 1 will not be used for an extended period of time unplug the power cord from the AC power outlet Note 230 volt models are not supplied with an AC power cord but are equipped with an IEC type power cord socket CAUTION Since your Klipsch SP 1 has built in electronics do not place it near sources of heat or moisture Take care to route the power cord so that it will not be cut damaged or pinched SPEAKER WIRE CONNECTIONS Switch your electronics OFF when making all connections When making any type of speaker wire connection be sure to observe proper polarity to and to Most speaker wire is insulated two conductor stranded construction and is color coded or has some distinguishing feature differen tiating the two conductors Speaker wire connectors on most loudspeakers and ampli ers are also color coded Typically RED is positive and BLACK is negative or ground It does not matter which conductor is connected to the positive or negative terminals of your equipment as long as you are consistent Be sure that the connections from all of the ampli er channels to all of the speakers in your system are connected in a like manner If not the quantity of bass will be reduced and the stereo image will be compromised Be careful not to have excess bare wire or loose
7. BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT EXCEPT TO THE EXTENT PROHIBITED BY LAW THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSO EVER INCLUDING BUT NOT LIMITED TO THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL PURPOSE Some states do not allow the exclusion or limitation of incidental or consequential damages or implied warranties so the above exclusions may not apply to you This Warranty gives you speci c legal rights and you may have other rights which vary from state to state 15 Dangerous Entry Care should be taken that no foreign objects or liquids fall or are spilled inside the device 16 Damage Requiring Service The device should be serviced by a Klipsch authorized service center when The plug or power supply cord has been damaged Objects have fallen or liquid spilled inside of the device The device has been exposed to moisture The device does not appear to be operating properly or exhibits a marked change in performance The device has been dropped or the cabinet has been damaged 17 Service The user should not attempt to service the device beyond what is described in the operating instructions All other servicing should be referred to quali ed personnel If dealer service is not available contact Klipsch customer service for a return authorization RA number before shipping Klipsch Customer Service 800 554 7724 All return shipments sho
8. a prise et pousser jusqu au fond CAUTION To reduce the risk of electrical shock do not expose this equipment to rain or moisture 1 Read Instructions All safety and operating instructions should be read before operating the device 2 Retain Instructions The safety and operating instructions should be retained for future reference 3 Heed Warnings All warnings on the device and in the operating instructions should be adhered to 4 Follow Instructions All operating and safety instructions should be followed 5 Water and Moisture The device should never be used in on or near water due to risk of fatal shock 6 Carts and Stands The device should only be used on carts or stands recommended by the manufacturer 7 Wall and Ceiling Mounting The device should be mounted on a wall or ceiling only as recommended by the manufacturer 8 Ventilation The device should always be located in such a way that it maintains proper ventilation It should never be placed in a built in installation or anywhere that may impede the ow of air through its heat sink or ventilation openings 9 Heat Never locate the device near heat sources such as a radiator oor register stove or other heat generating device 10 Power Supply The device should only be connected to a power supply of the type described in the operating instructions or as marked on the device 11 Polarization This product is equipped with a polarized line plug that
9. ers When placing the speaker below the television invert the speaker so that it rests on the angled top portion of its cabinet This will direct the sound up to compensate for a low placement height The grille may be installed in an inverted position so the Klipsch logo is properly oriented Four stick on rubber feet are included for attachment to the speaker bottom to prevent vibration and scratching of the television cabinet or shelf SYNERGY SS 1 WDST SURROUND SPEAKER One of the principle advantages of Klipsch s unique Wide Dispersion Surround Technology is greater placement exibility Due to their full 180 coverage pattern the SS 1s will perform well in a variety of locations The most common placement for home theater rooms is on the side walls adjacent to or behind the listening area or on the rear walls near the corners of the room A height of approximately ve to seven feet from the oor to the base of the speaker is recommended Your Klipsch surround speaker may be wall mounted by using the supplied keyhole brackets on the rear of the cabinet These two brackets are vertically oriented to attach to a pair of screws secured into a wall stud
10. g If one or both SP 1 subwoofers have little or no output Double check your power AC and system connections Make sure that the power switch on the rear control panels of both units is set to the ON or AUTO position Check that the power light on the front of the SP 1 is lit If not check the AC fuse When changing the AC main s power fuse unplug the power cord rst To access the fuse use the appropriate screwdriver to unscrew the cap on the fuse receptacle If the fuse is blown the lament inside the glass tube is burned through replace it with the same type and value as is printed on the ampli er panel next to the fuse holder NEVER INSTALL A LARGER FUSE THAN THE VALUE INDICATED ON THE AMPLIFIER PANEL If the fuse blows again when the subwoofer is powered up return the unit to your authorized Klipsch dealer for servicing by quali ed personnel If dealer service is not available contact Klipsch customer service for a Return Authorization number before shipping REQUIRED Klipsch Customer Service 800 554 7724 All return shipments should be made to Klipsch L L C 137 County Road 278 Hope AR 71801 RA return authorization number required The SP 1 s powered subwoofer ampli er is protected by a thermal sensor If the unit is run for extended periods beyond its designated power rating the thermal sensor will engage and shut down the subwoofer If this occurs turn the POWER
11. has one blade wider than the other To prevent electrical shock match the wide blade of the plug with the wide blade slot of the receptacle and insert fully 12 Power Cord Protection Power cables should be routed so they are unlikely to be stepped on or crushed by items placed on or against them Pay special attention to where the plug enters a socket or fused strip and to where the cord enters the device 13 Cleaning The device should be cleaned in accordance with the manufacturer s instructions 14 Periods of Non Use The device should be unplugged from the wall outlet when it is not in use for extended periods IF YOU PREFER YOU CAN REGISTER ONLINE AT WWW KLIPSCH COM For multiple speaker purchases please ll out only one warranty card Name Street Address City State Zip Home Phone Work Phone E mail Address Would you like to receive the latest product updates and news via e mail q Yes q No Product Purchase Model and serial number must be included to honor your warranty card For multiple speaker purchases please ll out only one warranty card Model Serial Number Model Serial Number Model Serial Number Model Serial Number Model Serial Number Model Serial Number What store did you purchase your Klipsch products from Store Name State How did you hear about Klipsch q Audio Home Theater Magazine q Other Magazine q TV q Radio q Newspaper q Trade S
12. how q Friend q Retail Dealer q Direct Mail Have you purchased Klipsch products before q Yes q No If yes what products Product Name s When do you hope to purchase additional loudspeakers q 6 mos 1 yr q 1 2 yrs How likely are you to consider Klipsch products for your upcoming purchases q Very likely q Somewhat likely q Doubtful If doubtful why q Don t carry product I m looking for q Too expensive q Klipsch dealer too far away q Other Please tell us about you q Married q Single q Student q Male q Female Age q 15 17 q 18 24 q 25 35 q 36 45 q 46 55 q 55 64 q 65 Annual Household Income q Under 25 000 q 25 35 000 q 35 50 000 q 75 100 000 q 100 000 Cut along dotted line and mail 4 9 16 SS 1 Wall Mount Hole Marking Template Klipsch Limited Warranty KLIPSCH L L C KLIPSCH warrants this product to be free from defects in materials and work manship subject to the terms set forth below For a period of ve 5 years from the date of purchase KLIPSCH will repair or replace at KLIPSCH s option this product or any defective parts excluding electronics and ampli ers in this product For products that have electronics or ampli ers the warranty on those parts is for a period of two 2 years from the date of purchase To obtain warranty service please contact the KLIPSCH authorized dealer from which you purchased this product If your dealer is not equ
13. ics Note You can bass lter the bookshelf models if a Klipsch powered subwoofer is used with them This will reduce distortion and increase dynamic range during passages that contain high levels of deep bass information Con gure your surround processor s main channels for the Small setting and connect the subwoofer to the line level subwoofer output on your electronics If speaker level hookups are used to connect the subwoofer set the processor s main channels to the Large setting and connect the SB 2s or SB 3s to the high pass ltered speaker output terminals on the powered subwoofer CONTROLS SP 1 ONLY Bass Contour This control adjusts the volume of the subwoofer relative to the mid and high frequency drivers Use this control to compensate for room acoustics and speaker placement This control only affects the level of the powered subwoofer in the SP 1 For initial setup try the FLAT position full counter clockwise and then increase as desired Power This switch has conventional ON and OFF positions as well as an AUTO setting In the AUTO position the subwoofer will turn itself on when it receives a signal from your system If no signal is sent for a period of 15 minutes the sub will turn itself off A red power light indicates a standby mode in which the ampli er will turn on when it senses a signal Green indicates the sub woofer is on and receiving a signal Troubleshootin
14. ipped to perform the repair of your KLIPSCH product it can be returned freight paid to KLIPSCH for repair Please call KLIPSCH at 1 800 KLIPSCH for instructions You will need to ship this product in either its original packaging or packaging affording an equal degree of protection Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that this product is within the warranty period must be presented to obtain warranty service This Warranty is invalid if a the factory applied serial number has been altered or removed from this product or b this product was not purchased from a KLIPSCH authorized dealer You may call 1 800 KLIPSCH to con rm that you have an unaltered serial number and or you purchased from a KLIPSCH authorized dealer This Warranty does not cover cosmetic damage or damage due to acts of God accident misuse abuse negligence commercial use or modi cation of or to any part of the product This Warranty does not cover damage due to improper operation maintenance or installation or attempted repair by anyone other than KLIPSCH or a KLIPSCH dealer which is authorized to do KLIPSCH warranty work Any unauthorized repairs will void this Warranty This Warranty does not cover products sold AS IS or WITH ALL FAULTS REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER KLIPSCH SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR
15. lectronics subwoofer or LFE output Do not connect this input to a full range un ltered pre amp output It is typically used with the newest 5 1 six channel surround sound systems The LFE channel contains a different bass signal than the bass frequencies present in the other channels This information can be up to 10 decibels louder than the main channel bass signals so caution should be exercised when connecting to this output and initially adjusting the SP 1 s BASS CONTOUR control The LFE IN must not be the only connection to the SP 1 The SPEAKER IN terminals are the primary connection for the SP 1 LFE OUT SP 1 Only optional This output is provided to feed the LFE signal to the other SP 1 if it is dif cult or inconvenient to connect it directly to the LFE output on your electronics BASS MANAGEMENT Most surround sound electronics are equipped with a bass management system that permits the selec tion of a full or limited range ltered operation for each speaker You will normally con gure the main channels of your surround processor to the Large or Full Range setting and the center and surround channels to the Small or Limited Range setting The subwoofer or LFE channel of your electronics should have its low pass lter engaged when connecting to the optional LFE IN input on the SP 1 Consult your Klipsch dealer for more speci cs on the bass management con guration of your electron
16. mily the Klipsch Synergy Series was developed to provide optimal performance in either a home theater or music system For home theater use Klipsch engineers have developed voice matched center and rear surround speakers to complement the main channel speakers All Synergy models offer the accuracy dramatic imaging and high sensitivity that characterize the live Klipsch sound By utilizing our new Tractrix Horn technology the Synergy models offer the type of high quality performance normally found only in professional speakers ensur ing you a truly enjoyable listening experience If this is your rst Klipsch purchase welcome to the fold if this is an additional Klipsch purchase we thank you for your loyalty When it comes to the best in home entertainment Klipsch is a sound choice Please take the time to ll out the enclosed warranty registration card or if you prefer you can register your products online at www klipsch com This information helps us serve you better and assists our dealers in meeting your needs as a valued Klipsch customer Should you have any questions or need more information on Synergy or other Klipsch products please contact us We will be happy to assist you and welcome your feedback Thank you for choosing Klipsch loudspeakers Sincerely Fred S Klipsch Chairman amp CEO Component Speci cations SB 2 Sensitivity 93dB 1 watt 1 meter Bandwidth 54Hz 20kHz 3dB Nominal Impedance 8 oh
17. ms Crossover Frequency 2400Hz Power Handling 85 watts maximum continuous 340 watts peak Enclosure Type Bass re ex via wide are rear ring port Drive Components Two way system using one 1 2 54cm K 101 S neodymium magnet aluminum dome compres sion driver with a 90 x 60 Tractrix Horn and one 6 5 16 51cm K 1092 SB magnetically shielded woofer featuring a polymer housing and IMG cone Net Weight 13 lbs 5 9kg Height 15 38 1cm Width 7 3 18 5cm Depth 9 75 24 7cm Cabinet Medium density ber board construction MDF Finish Woodgrain vinyl veneer SB 3 Sensitivity 94dB 1 watt 1 meter Bandwidth 52Hz 20kHz 3dB Nominal Impedance 8 ohms Crossover Frequency 2700Hz Power Handling 100 watts maximum continuous 400 watts peak Enclosure Type Bass re ex via wide are rear ring port Drive Components Two way system using one 1 2 54cm K 101 S neodymium magnet aluminum dome compres sion driver with a 90 x 60 Tractrix Horn and one 8 20 3cm K 1093 SB magnetically shielded woofer featuring a polymer housing and IMG cone Net Weight 18 lbs 8 18kg Height 17 43 18cm Width 8 69 22 06cm Depth 11 25 28 57cm Cabinet Medium density ber board construction MDF Finish Woodgrain vinyl veneer SF 1 Sensitivity 94dB 1 watt 1 meter Bandwidth 40Hz 20kHz 3dB Nominal Impedance 8 ohms Crossover Frequency 2kHz Power Handling 100 watts maximum continuous 400 watts peak
18. or home theater and two channel performance This series offers a choice of two bookshelf speakers the SB 2 and SB 3 and three oorstanding main channel speakers the SF 1 and SF 2 and a model with a built in powered subwoofer the SP 1 The voice matched companion SC 1 center speaker and SS 1 surround speakers complete the family A smaller version of our newest square Tractrix Horn driven by an aluminum diaphragm tweeter is paired with high output woofers featuring glass ber reinforced cast polymer frames and graphite stiffened injection molded polypropylene cones All front channel models feature video shielding and a oating grille design that gives the speakers a handsome contemporary style with minimal sonic interference Flush mounted components and nar row front pro les are combined with time aligned drivers and simple minimum phase lter networks to provide truly extraordinary soundstaging The rear sound eld in a full surround system con gura tion is provided by the Klipsch SS 1 Wide Dispersion Surround Technology speakers These speakers contain an array of three drivers that ood the back of the listening room with high quality direct and re ected sound providing both pinpoint rear channel imaging and ambient envelopment Speaker Placement SYNERGY MAIN SPEAKERS Both speakers should be placed on the same wall facing the listening area Space the loudspeakers so they are between six and 15 feet apart Fo
19. r best results with the bookshelf models use a high quality rigid stand that places the speaker s horn tweeter at ear level when seated For a higher quality stereo image angle or toe in the speakers towards the listener The desired spread between the speakers may be different for a home theater application than it would be for a two channel audio system Some correlation between the size of the video and sonic image may dictate the nal placement of the speakers For best results bring the main speakers forward of the loca tion of the center speaker so that all three front speakers are equidistant from the central viewing posi tion Some surround electronics allow you to compensate for this electronically by inputting the dis tance from the viewing seat to each speaker Additional bass output will result if you place the speakers in a corner or near a wall due to the addi tional re ected energy from the walls and oor This may however degrade soundstage quality so these two attributes must be balanced depending upon your sonic priorities Room acoustics vary so experi ment with speci c placement within the listening area Four stick on rubber feet are included to attach to the speaker bottom for use on shelves or hard surface ooring SYNERGY SC 1 CENTER SPEAKER Place the center speaker on top of or just below the video screen centered This anchors center channel sounds to the on screen image particularly for off center view
20. ss re ex via wide are rear ring port Drive Components Three way system using one 1 2 54cm K 101 S neodymium magnet aluminum dome compres sion driver with a 90 x 60 Tractrix Horn one 5 25 13 33cm K 1076 SV magnetically shielded mid bass woofer featuring a polymer housing and IMG cone and one 8 20 32cm K 1077 SB magnetically shielded woofer featuring a polymer housing Subwoofer Ampli er Class A B MOSFET 225 watts FTC rated power 55 watts 4 ohms 22 125Hz 1 THD maximum Auto Power 2 second ON delay 15 minute OFF delay Inputs High level speaker terminals via ve way binding posts 1 Line level dedicated LFE input via RCA phono jack non ltered Outputs 1 Line level LFE output via RCA phono jacks pass through from LFE input Net Weight 47 lbs 21 36kg Height 37 93 98cm Width 9 22 86cm Depth 14 35 56cm Cabinet Medium density ber board construction MDF Finish Woodgrain vinyl veneer Voltage 110 120VAC 60Hz Export version 230VAC 50 60Hz SC 1 Sensitivity 95dB 1 watt 1 meter Bandwidth 60Hz 20kHz 3dB Nominal Impedance 8 ohms Crossover Frequency 2 2kHz Power Handling 100 watts maximum continuous 400 watts peak Enclosure Type Sealed Drive Components Two way system using one 1 2 54cm K 101 S neodymium magnet aluminum dome compres sion driver with a 90 x 60 Tractrix Horn and two 5 25 13 3cm K 1079 SV magnetically shielded woofers featuring polymer housings
21. strands of wire at the connections This could cause a short between adjacent positive and negative terminals dam aging your speakers and ampli er Eighteen gauge AWG wire is the minimum size recommended for short distances with larger gauges recommended for longer runs Consult your Klipsch dealer for speci c suggestions Connect the SB 2 SB 3 SF 1 SF 2 or SP 1 to the Front or Main channel speaker outputs of your system s power ampli er Connect the SC 1 to the Center channel speaker output of your system s power ampli er Connect the SS 1 to the Rear or Surround channel speaker outputs of your system s power ampli er When connecting surround speakers to the rear channels of a 5 1 channel system it is important that they are hooked up to the appropriate left and right rear channels as the surround effects are in stereo LINE LEVEL CONNECTIONS SP 1 ONLY Switch your electronics OFF when making all connections These connections should be made using high quality shielded interconnect cables terminated with RCA phono plugs These cables should be as short as possible and kept away from noise generating electrical equipment such as digital elec tronics or electric motors Consult your Klipsch dealer for speci c cable recommendations LFE IN SP 1 Only optional The LFE IN input on the SP 1 is a full range input that requires a low pass ltered signal from your surround e
22. uld be made to Klipsch L L C 137 County Road 278 Hope AR 71801 RA return authorization number required We Want Your Klipsch Product to Look and Sound as Good as When it Left the Factory Please Check Promptly for Transit Damage Each Klipsch product is individually tested for sonic quality and inspected for superior appearance before it leaves the Hope Arkansas factory Your loudspeaker left the factory in perfect condition in packaging carefully engineered to protect both the working parts and nish However in certain extreme circumstances the products may be damaged in transit To ensure that your loudspeaker is in its original condition please inspect it immediately If damage is discovered notify the authorized Klipsch dealer that the unit was purchased from or the trans portation company responsible for safe delivery In the latter case make a request for inspection from the transportation company and hold the product in its original shipping carton for the inspector After a joint inspection report is made le a claim with the transportation company Dear Klipsch Synergy Series Owner Congratulations on your purchase of Klipsch Synergy Series loudspeakers These products represent the best new thinking coupled with the Klipsch tradition of sonic excellence The Synergy Series was developed using the latest in materials and technology to deliver extraordinary sound from today s digital sources Designed as a fa
Download Pdf Manuals
Related Search