Klipsch Palladium P-312W User's Manual
Contents
1. function described under the Save Settings feature described in this section of the manual Lowpass This screen is used to adjust the subwoofer s upper frequency limit to achieve a proper blend with your system s main speakers A higher frequency Hz is typically used with smaller bass limited main speakers and a lower frequency setting is customarily used with larger Koorstanding models This filter can be adjusted from 40Hz to 120Hz as required or defeated if the low pass filter function is being performed by your system s electronics Use the Left Right touch keys to adjust the lowpass filter To defeat this filter press and hold the Right touch key until Lowpass Off LFE Mode is displayed Refer to your surround processor s owner s manual for more Bass Management information From this screen press the Down or Up touch key to access other control settings Lowpass Slope This screen is used to adjust how aggressively the subwoofer rejects frequencies above the low pass filter s set ting This screen is not visible if the Lowpass Alter above is set to Lowpass Off LFE Mode There are four settings to choose from 18 24 36 amp 48dB octave The higher the number the more the upper frequencies are removed from the subwoofer s output Use the Left Right touch keys to select the desired filter slope Start with either the 24 or 36dB octave setting and adjust from there if required Adjustment of this parameter can help t2. Music Night User 1 and User 2 This allows for global recall of all of the above settings to tailor the subwoofer s performance to compensate for differing source material and uses The display backlighting will turn off if no keypad inputs are made for 10 seconds The display will return to the Volume screen if no keypad inputs are made for 10 seconds If the display is in standby mode or on the default volume menu during normal operation the initial key press will turn on the display backlighting The second key press will initiate a control adjustment or the selection of another mode In periods of low humidity it is possible that a static electricity discharge to the subwoofer may cause a momentary interruption in the subwoofers output or changes to the LCD display content Any display content errors will be corrected when the screen changes modes Volume Use the left and right touch keys to adjust the subwoofer s volume level to match the output of your main speakers Press and hold or press and release the Left touch key to decrease the subwoofer s volume Press and hold or press and release the Right touch key to increase the subwoofer s volume to the desired level From this screen press the Down touch key to access other control settings Recall Settings This screen is used to select any one of five user defined memory presets titled Movie Music Night User 1 and User 2 Use the Lef
3. The Klipsch Palladium Series has drawn on engineering design and manufacturing resources from all over the world In addition to our formidable team in the USA we have used European industrial designers British theoreti cal physicists and manufacturing and production specialists from China The Palladium Series is the culmination of over 60 years of research and engineering advancements having been designed with the most advanced computer aided design CAD tools available rigorously evaluated using our own in house proprietary software built to the most stringent quality standards and voiced by a panel of our most experienced listeners No Klipsch loudspeaker has ever had more care and attention to every detail lavished on it than your Palladium Series subwoofer Although building one subwoofer is relatively straightforward building hundreds of subwoofers is challenging Measurements play an important role in analyzing subwoofer characteristics but the human ear is the ultimate test gear for evaluating its reproduction quality At Klipsch every design is strictly evaluated using listening tests designed to expose even the very smallest weakness All final voicing is performed under blind conditions using trained listeners and standard audio sound tracks selected based on their particular area of auditory excellence All information is tabulated and reported back to the designer for analysis In almost all cases Klipsch products are evaluated
4. installation or attempted repair by anyone other than KLIPSCH or a KLIPSCH dealer which is authorized to do KLIPSCH warranty work Any unauthorized repair will void this Warranty This Warranty does not cover product sold AS IS or WITH ALL FAULTS REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER KLIPSCH SHALL NOT BE LIABLE FOR ANY INCIDEN TAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT EXCEPT TO THE EXTENT PROHIBITED BY LAW THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRAN TIES WHATSOEVER INCLUDING BUT NOT LIMITED TO THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL PURPOSE Some states do not allow the exclusion of incidental or consequential damages or implied warranties so the above exclusions may not apply to you This Warranty gives you specific legal rights and you may have other rights which vary from state to state Warranty Outside The United States and Canada The warranty on this product if it is sold to a consumer outside of the United States or Canada shall comply with applicable law and shall be the sole responsibility of the distributor that supplied this product To obtain any applicable warranty service please contact the dealer from which you purchased this product or the distributor that supplied this product Page 15
5. Klips PALLADIUM y 4 NR 2 P 312W Owner s Manual Page 2 ty Instructions READ these instructions KEEP these instructions HEED all warnings FOLLOW all instructions DO NOT use this apparatus near water CLEAN ONLY with dry cloth DO NOT block any ventilation openings Install in accordance with the manufacturer s instructions DO NOT install near any heat sources such as ra diators heat registers stoves or other apparatus including amplifiers that produce heat ONLY USE attachments accessories specihed by the manufacturer USE only with a cart stand tripod bracket or table specifiedby the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over UNPLUG this apparatus during lightning storms or when unused for long periods of time REFER all servicing to qualified service person nel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped When making or changing any connections to your system switch all the electronics OFF Do NOT listen to music for long periods at extreme volume settings Doing so can perma nently damage your hearing When run
6. accurate response If the second subwoofer is connected directly to your system the Palladium subwoofer s ARC will react to rather than control the response of the other subwoofer As a result we recommend the following procedure when connecting a second sub woofer to these outputs Play a signal such as one of the Palladium subwoofer s two demo tracks and set the volume control of the second subwoofer to approximately match that of the Palladium subwoofer Defeat the secondary subwoofer s lowpass setting by selecting the Bypass or LFE mode or set the lowpass control to its highest frequency if these options are not present Set the secondary subwoofer s phase control to 0 Run the Room Correction function on the Palladium subwoofer As with the initial setup of your Palladium subwoofer listen to a track with a repeating bass line in your listen ing position Experiment with alternate phase settings on the secondary sub while repeating this track If one of these alternate settings yields an increased amount of bass choose that setting and run the Palladium subwoofer s room correction function again Please note that if either the volume or phase settings on the secondary sub are changed after running the ARC function you will have to either reset them to the location they were at when the room correction was performed or run the ARC calibration again to compensate Page 11 This section describes th
7. against similarly priced competitive models It is only in this manner that Klipsch can truly rely on the quality of feedback received eliminating skewed data that may result due to inXuences caused by price brand recognition or visual appeal Design The P 312W is a triple driver subwoofer with high output and extremely low distortion The three drivers of the P 312W are comprised of an active front firing 12 inch alumi num fiber composite hybrid cone and a pair of side firing 12 inch aluminum fiber composite hybrid cone passive radiators These drivers are mated with an internal BASH digital hybrid amplifier and Klipsch s advanced Digitally Controlled Subwoofer DCS operating system All features and functions of the DCS system are accessed via a touch panel located on top of the subwoofer Inputs and outputs are located on a panel below the amplifier heatsink on the rear of the enclosure This arrangement locates cabling behind the subwoofer for a clean installation and keeps all of the controls up front readily accessible for the user When not in use the touch panel control lighting turns off leaving nothing but the elegant appearance of the aluminum trim and black glass panel juxtaposed against the striking zebra grain veneer The superior components used in the P 312W are complemented by the unique enclosure design and highlighted by the elemental performance of the industrial design The massive laminated MDF enclosure is bas
8. e factory and should not be removed The Accessories box contains remote control calibration microphone with storage bag microphone tripod and microphone cable There isa pair of gloves located in a pocket in the side of the packing carton under the Owner s manual Identify all the components If any item is missing or damaged report this immediately to your Klipsch dealer and the transport contractor for action Page 3 1e Loudspeaker Connection Procedure There is a specific procedure to be followed Switch off and unplug the amplifier s and all source electronics from the mains power Place the subwoofer in the general area where you want it Connect the subwoofer following the instructions under the connecting the subwoofer section of this manual Finalize the position of the loudspeakers Fit the front grille if desired TAKE CARE NOT TO TOUCH THE DRIVE UNITS WHEN YOU MOVE THE SUBWOOFER AROUND TO PRESERVE THE FINISH WHEN HANDLING YOUR SUBWOOFER USE THE GLOVES THAT ARE PROVIDED Fitting and Removing the Grilles To fit the front grille align the posts on the grille with the post cups on the front of the subwoofer and gently press on the grille Use care to ensure that the grille clears the aluminum control panel extrusion area around the logo Do not strike or forcibly press on the grille or grille posts as damage to the grille or finish of your subwoofer could occur The round side gril
9. e features found on the supplied remote control for your Palladium P 312W subwoofer The remote control works via infrared and as such will need a clear line of sight to the infrared receiver located on the lower right quadrant of the front panel The remote will work with or without the front panel grille installed The codes from the remote can be programmed into any standard learning remote control if your system includes such a device Volume These buttons adjust the level of the sub woofer up and down as described in the Volume control section of this manual X over These buttons adjust the frequency of the lowpass filter up and down as described in the Lowpass control section of this manual PALLADIUM Phase These buttons adjust the phase control up ip ps pe and down as described in the Phase control section of this manual a O ARC On Off This button toggles the ARC feature on and ru D er off as described in the Room Correction EG MODE control section of this manual EO Mode Klipsch d These buttons provide direct access to any of the three EQ modes as described in the EQ Mode control section of this manual Presets These buttons provide direct access to any of the five presets as described in the Recall Settings and Save Set tings control sections of this manual Page 12 About Your Loudspeaker An International Project
10. ed on a curved non parallel wall structure for minimal resonance and maximum structural rigidity Page 13 Page 14 Care and Maintenance Very little maintenance is required To maintain the finish of the loudspeakers wipe them carefully with a soft lint free polishing cloth Occasionally and to remove fingermarks etc wipe the cabinets with a barely damp clean soft cloth and finish with a lint free polishing cloth NEVER use any form of spray furniture polish saturated polishing cloth or the like Doing so will dull and streak the fine finish of the cabinets Do NOT use a vacuum cleaner to clean the grilles while they are installed on the cabinet To clean the grilles remove them brush them out by hand with a soft brush and replace them Never touch the drive units either with your hands or with any tool or other object This may damage the drive units irreparably Do NOT store the microphone in a high humidity environment Also avoid shocks and drops Warranty The Warranty below is valid only for sales to consumers in the United States and Canada KLIPSCH L L C KLIPSCH warrants this product to be free from defects in materials or workmanship subject to the terms set forth below for a period of five 5 years from the date of purchase During the Warranty period Klipsch will repair or replace at KLIPSCH option this product or any defective parts excluding electronics and amplifiers For products that have electr
11. ings to find the one that best suits your particular room and preferences When choosing your subwoofer s location keep in mind that you will need to connect the subwoofer s built in amplifier to an AC power outlet The Palladium Series subwoofer features Klipsch s proprietary Adaptive Room Correction This patent pending technology will identify the major acoustic anomalies in the low frequency range of your listening room s acoustics and compensate for them automatically While the corrected response may at first sound like a reduction in bass quantity the benefit is a much higher quality bass reproduction featuring audibly faster tran sient response and more noticeable extension of extremely low frequency program material See the Adap tive Room Correction section of this manual for further information on this feature Page 5 onnecting the Subwoofer Caution Turn off your preamplifier receiver and your subwoofer before making any connections Inputs and Outputs Line In Your Palladium Series powered sub woofer is connected via line level connections only RCA type and XLR inputs are provided and either may be used Do not connect both at the same time Use the Subwoofer LFE or Pre amp outputs of your systems electronics to connect to the LINE IN input connections of your subwoofer Use high quality a J CAUTION shielded line level cables for these ON a AGAINST RISK OF FIRE connec
12. les cover the two passive radiators and come pre installed from the factory They are attached via rubber capture posts to special fasteners on the passive radiators If these grilles should ever need to be re installed make sure you orient them properly so that the curve of the grille follows the curve of the subwoofer side panel and gently press them back into place Although operating the P 312W subwoofer with the front grille on or off is a matter of personal taste moving or connecting the subwoofer should always be done with the front grille removed Be especially careful not to touch the drive unit Page 4 Positioning Subwoofers Never allow objects or furniture to impede the subwoofer or place objects on top of it 6 16 CENTER Positioning your Palladium Series subwoofer Klipsch powered subwoofers are designed to reproduce deep bass and deliver the impact that makes your movies and music come alive Typically optimum performance will result if you place your subwoofer in a corner of the room on the same wall as your front channel speakers Please note that room placement can have a dramatic effect upon the performance of your powered subwoofer Corner placement as suggested above will increase the amount of bass output placing the subwoofer along the middle of a wall or out in the room will decrease the amount of bass output Experiment with a number of different placement options and control sett
13. ning loudspeaker cables do not trail them over open Koor spaces where they could cause an accident Cover them or route them around potential troublespots This symbol indicates that there are important operating and maintenance instructions in the literature accompany ing this unit This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit WARNING To reduce the risk of fire or electrical shock do not expose this ap paratus to rain or moisture WARNING Voltages in this equipment are hazard ous to life No user serviceable parts inside Refer all servicing to qualified service personnel CAUTION Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Before switching on your sound system turn the volume level down After switching the system on turn the level up gradually Do not use extreme settings of Treble Bass or EO Ideally set the tone controls Mat and turn any EQ off These loudspeakers are extremely heavy Do not move them by yourself Always get help Getting Started Unpacking This subwoofer is heavy Do not lift or move this subwoofer by yourself Always have someone help you What s in the box e Powercord The grille box contains one grille for the front of the subwoofer The side grilles are installed at th
14. o optimize the acoustic blend with your main speakers The proper setting will depend on room acoustics your main speaker s performance the placement of the speakers and the subwoofer in the room From this screen press the Down or Up touch key to access other control settings Phase This screen is used to adjust the subwoofer s acoustic phase to match that of your main speakers Use the Left Right touch keys to adjust the subwoofer s phase from O to 180 The proper setting of this control is highly dependant on room acoustics and the position of your subwoofer in the room After setting the volume and lowpass controls adjust the phase to 0 and listen to a recording with a prominent repeating bass line in your intended listening position Repeat this process with the 180 setting and use the setting that yields the greatest amount of bass output If neither of these settings is better than the other experiment with intermediate set tings From this screen press the Down or Up touch key to access other control settings Features and Controls 3 Room Correction This screen is used to activate the automatic Adaptive Room Correction ARC feature Plug the supplied microphone into the MIC IN jack on the subwoofer s rear panel and place it in the intended listening position Press the Enter key to activate the calibration sequence Calibrate will be displayed along with the ascending frequency of the test tone and a bar gra
15. onics or amplifiers the Warranty period on those parts is for a period of two 2 years from the date of purchase To obtain Warranty service please contact the KLIPSCH authorized dealer from which you purchased this product If your dealer is not equipped to perform the repair of your KLIPSCH product it can be returned freight paid to KLIPSCH for repair Please call KLIPSCH at 1 800 KLIPSCH for instruc tions You will need to ship this product in either its original packaging or packaging affording an equal degree of protection Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that this product is within the Warranty period must be presented or indicated to obtain Warranty service This Warranty is invalid if a the factory applied serial num ber has been altered or removed from this product or b this product was not purchased from a KLIPSCH authorized dealer You may call 1 800 KLIPSCH to confirm that you have an unaltered serial number and or you purchased from a KLIPSCH authorized dealer This Warranty is valid only for the original purchaser and will automatically terminate prior to expiration if this product is sold or otherwise transferred to another party This Warranty does not cover cosmetic damage or damage due to misuse abuse negligence acts of God accident commercial use or modification of or to any part of the product This Warranty does not cover damage due to improper operation maintenance or
16. ph of the sound level loudness The subwoofer will measure the rooms acoustic effect and compensate for it When the calibration sequence is complete Calibration Successful will be displayed If the subwoofer s volume level is too low or the microphone was either disconnected or improp erly connected Calibration Unsuccessful will be displayed From this screen press the Down or Up touch key to access other control settings Save Settings nu This screen is used to store all of the above control settings in one of five memory presets Movie Music Night User 1 and User 2 Use the Left Right touch keys to select the desired preset and press the Enter key to store your current control settings Settings Saved will be displayed After the settings are stored in memory the display will return to the default Volume adjustment screen All of the user settings in the five presets can be erased and restored to their default values by scrolling down to the last System Info screen Press the Right touch key twice to get to the System Reset screen Press the Enter key and all user settings will be replaced with the default settings Reset Complete will be displayed From this screen press the Down or Up touch key to access other control settings Disp Brightness This screen is used to adjust the brightness level of the display screen when the backlighting is on Use the Left Right
17. t Right touch keys to select the desired group of stored control settings and press the Enter key to apply them Settings Recalled will then be displayed During initial setup skip this screen until all other initial control adjustments have been made If nothing has been saved in the selected preset the display will read Preset Empty From this screen press the Down or Up touch key to access other control settings Page7 Page 8 ures and Controls 2 EQ Mode This screen is used to select two different bass emphasis settings titled Punch and Depth They are designed to complement different types of program material such as movie soundtracks or music The Punch setting emphasizes the 55Hz region while the Depth setting boosts the 30Hz range A third setting is titled Flat which defeats these two settings Use the Left Right touch keys to select the desired EQ setting From this screen press the Down or Up touch key to access other control settings Room Correction On Off This screen indicates whether the Room Correction filter is engaged See the section on Room Correction for more information Press either the Left or Right touch keys to turn this function on or off This screen will not appear if the Room Correction function has not been activated the Room Correction calibration was unsuc cessful or the user memories have been erased using the System Reset
18. tions o REPLACE ONLY WITH SAME k E TYPE FUSE AND RATING p ATTENTION UTILISER UN FUSIBLE DE Line Out RECHANGE DE M ME TYPE O ET CALIBRE This jack can be used as an alternate method of connecting a second subwoofer to your system This second subwoofer can function as a slave to the primary subwoofer For more on this see the Back Pan el Features section of this manual RCA type and XLR inputs are pro vided and either may be used Do va O not connect both at the same time Use high quality shielded line level cables for these connections Page 6 Features and Controls Touch Panel Controls All ofthe subwoofer s controls and settings are accessed through the touch panel key pad and display located on the top of the subwoofer s cabinet The only exception to this is the main AC Volume is AO power switch which is located on the rear panel of the subwoofer Use the A Up or Y Down touch keys to scroll through the list of control options Use the 4 Left or Right touch keys to make adjustments to a given control setting Use the Enter touch key when the or Enter appears on the display to store and recall custom settings or to lock the keypad After adjusting the individual control param nu nu eters for Volume EQ Mode Lowpass Low pass Slope and Phase your settings can be stored in one of five user memories Movie
19. touch keys to select from the brightness intensities From this screen press the Down or Up touch key to access other control settings Power This screen is used to select the Auto On or the Always On power mode for the subwoofer s amplifier Use the Left Right touch keys to select between these two modes When Auto On is selected the subwoofer will auto matically turn on when it senses a signal It will automatically turn off after 20 minutes if no signal is present and the display screen will show Standby In the Always On setting the subwoofer will remain on as long as the main AC power switch on the subwoofer s rear panel is in the On position From this screen press the Down or Up touch key to access other control settings Play Demo Use this screen to activate either of two 12 second demonstration programs Use the Left Right touch keys to select the desired demo and press the Enter key to start playing the selection From this screen press the Down or Up touch key to access other control settings Page 9 Page 10 tures and Controls 4 Keypad Lock This screen is used to lock the keypad and prevent unintentional changes to your settings by other users After making all desired adjustments press the Enter key to lock the keypad Keypad Locked Hold gt to Unlock will be displayed The display will then return to the default Volume screen after about 20 seconds To unlock the ke
20. uto On feature to function Set this switch to the Off position if the subwoofer will not be used FOR CONTINUED PROTECTION for an extended period of time i e vacation or when mak ey ee 7 TYPE FUSE AND RATINO ing any connections to the subwoofer d Q ramen on ANALE pe RECHANGE DE MEME TYPE ET CALORE USB This USB computer interface allows access to additional advanced features within the subwoofer s ARC room correction software Optional proprietary Klipsch software and a higher level of technical knowledge are required to correctly utilize this capability This port can also function as an alternative control interface with A V control systems that can un O ue utilize a USB connection Please contact your authorized Klip N sch dealer or Klipsch Technical Support for more information Line Out There are both RCA type and XLR connections provided for line out signals Choose the one appropriate for your system Do not use both at the same time This connection can be used as an alternate connection point for a second subwoofer as opposed to connecting them both to your electronics Be aware that the signal output from these jacks is affected by the Volume EQ Lowpass Lowpass Slope Phase and Room Correction settings of your Palladium subwoofer The advantage of this is the ability of the Adaptive Room Correction ARC function to correct the response of the second subwoofer resulting in a more
21. ypad press and hold the Left and Right touch keys until the display returns to the Volume screen The keypad is now unlocked It is suggested that you write down all of your settings for future reference in case the keypad is unlocked and your settings are changed by another user From this screen press the Down or Up touch key to access other control settings System Info Press gt This screen is used to access the software Version number and System Reset function to clear all user settings and memories Refer to the Save Settings section of this manual If the System Reset function is activated all of the memory presets are erased and the subwoofer s controls are restored to the default settings of Volume Odb EQ Mode Flat Lowpass Off LFE Mode Phase 0 Disp Brightness highest level and Power Always On For more information on the controls mentioned in this manual and on the bass management settings of your electronics see your authorized Klipsch dealer or visit www klipsch com Back Panel Features This section describes the features and connections found on the amplifier on the back panel of the subwoofer It also describes the manner for connecting a second subwoofer as a slave unit to the primary subwoofer Power On Off This is the main AC power switch for the subwoofer This switch must be in the On position for the subwoofer to operate and for the A
Download Pdf Manuals
Related Search