Kidde KN-COB-IC User's Manual
Contents
1. N SIGNALING LISTED Carbon Monoxide Alarm User s Guide Models KN COB IC and KN COP IC KN COB IC le KN COP IC imme with Digital Display Kidde eee e 120V AC Wire In e 9V Battery Backup Interconnectable with other Kidde alarms Ne J ATTENTION Please take a few minutes to thoroughly read this user s guide which should be saved for future reference and passed on to any subsequent owner Manual P N 820 1685 Rev B 10 12 2512 7213 00 What to do When the Alarm Sounds Carbon Monoxide Alarm Procedure WARNING Activation of the CO Alarm indicates the presence of Carbon Monoxide CO which can kill you Operate the Test Reset button Call your emergency services Fire Department or 911 PHONE NUMBER mmediately move to fresh air outdoors or by an open door window Do a head count to check that all persons are accounted for Do not reenter the premises nor move away from the open door window until the emergency services responders have arrived the premises have been aired out and your alarm remains in its normal condition After following steps 1 3 if the alarm reactivates within a 24 hour period repeat steps 1 3 and call a qualified appliance technician to investigate sources of CO from fuel burning equipment and appliances and to inspect for proper operati of equipment PHONE NUMBER If problems are identified during this inspection have th2. Memory Reset or power up The Peak Level display feature will display levels between 11 999 PPM Although the Peak Level feature will display levels below 30 PPM these levels will not result in an alarm no matter how long the device is exposed to these levels The Peak Level feature is helpful in identifying if you have had a CO reading since resetting the alarm Concentrations of CO between 1 and 30 PPM can often occur in nor mal everyday conditions Concentrations of CO below 30 PPM may be an indication of a transient condition that may appear today and never reappear Some CO conditions may start out as low level leaks but could develop into CO concentrations that may become harmful Peak Level Memory Reset Press the Peak Level button with the button still pressed press the Test Reset button for two seconds and release The number on the display will turn to 0 the memory will be cleared and the alarm will begin monitoring for CO The Peak Level memory is also reset when the unit loses power NOTE This unit is sealed The cover is not removable Due to the loudness of the alarm we suggest that you place your fingers over the sounder opening while testing your alarm CAUTION Continuous exposure to the high sound level of this alarm over an extended period of time may cause hearing loss Testing To test the alarm press the Test Reset button If the unit is operating properly you should hear 4 quick beeps follow
3. time to replace the unit at a more convenient time e between the the CO ppm reading and End to he unit right away This silence feature can only be used for a two days before it will no longer function and the beep cannot will still monitor and alarm for CO during this period ity will be lost ure has been activated refer to tamper resist feature description in section 4 direction of the OFF for removal instructions Remove the alarm from the mounting plate by rotating the alarm in the arrow on the cover To disconnect the AC Quick Connector harness squeeze the locking arms on the sides while pulling the i a eae connector away from see section 4 After the alarm has been removed you can and replace the battery ructions are provided he battery door open the battery door Battery installation ins on the inside of When installing as shown on unit labe down into the battery install the battery he bottom he battery orien compartment and of the alarm the battery battery tab Press the CAUTION If the battery tab is not held down in the battery compartment by the battery the battery door will not close the AC Quick Connector will not attach to the alarm and the alarm will not attach to the mounting plate After installing or changing the battery reinstall your alarm Test your alarm by using the Test Reset button and check that the green Power
4. LED is on Maintenance Tips To keep your alarm in good working order you must follow these simple steps e Test the alarm once a week by pressing the Test Reset button e Vacuum the alarm cover once a month to remove accumulated dust e Never use detergents or solvents to clean the alarm Chemicals can permanently damage or temporarily contaminate the sensor e Avoid spraying air fresheners hair spray paint or other aerosols near the alarm Do not paint the unit Paint will seal the vents and interfere with proper sensor operation Move the CO Alarm to a remote location to prevent possible damage or contamination of the sensor prior to performing any of the following Staining or stripping floors or furniture painting or wall papering e Using aerosols or adhesives ZX WARNING Reinstall the CO Alarm as soon as possible to assure continuous protection The following is a list of substances that at high levels can damage the sensor or cause temporary readings that are not CO readings e Ethylene ethanol alcohol iso propanol benzene toluene ethyl acetate hydrogen hydrogen sulfide and sulfur dioxide e Also most aerosol sprays alcohol based products paint thinner sol vent adhesive hair spray after shave perfume auto exhaust cold start and some cleaning agents FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15
5. Test Reset Alarm for test function Green and amber _ silence button is pressed purposes only LED s on repeated once End of RED LED flashes Two quick End of unit life See End of Life unit life two times every beeps every Notification in indicator 30 seconds 30 seconds Maintenance Section 7 Model KN COP IC with digital display Operating Characteristics Whenever the alarm is operating the green Power LED is illuminated and the digital display will display O to indicate the unit is monitoring for CO If the alarm senses dangerous levels of CO the red Alarm LED will flash the digital display will indicate the CO concentration in parts per million PPM and the alarm will emit an audible alarm pattern This alarm will display a O if CO concentrations between 0 and 30 PPM have been detected within the last 15 seconds When the unit is first powered up the digital display will show three eights indicating the alarm is in the start up mode The three eights will remain for approximately 20 seconds After 20 seconds the alarm should display O and begin monitoring the air for CO and will continue to do so as long as it receives power The following table illustrates the possible digital displays describes the audible alarm patterns and the recommended actions to take Operating and Alarm Characteristics LED Display Shows Alarm Sound Unit Status Recommendation falalan Grief 8
6. of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment gener ates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful inter ference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that o which the receiver is connected Consult the dealer or an experienced radio TV technician for help TEN YEAR LIMITED WARRANTY Warranty Coverage The manufacturer warrants to the original consumer purchaser that this product except battery will be free of defects in material and workmanship for a period of ten 10 years from date of purchase The manufacturer s liability hereunder is limited to replacement of the product repair of the product or replacement of the product with repaired product at the discretion of the manufacturer This warranty is void if the product has been damaged by
7. 88 along 4 quick beeps Self checking when None CO has not 8685 with any number 5 seconds AC powered Test been detected between 100 and 300 silence button was pressed Numbers shown for Red LED flashes with beeps repeated once or unit was first test purposes only Green and amber LED s on powered fam Steady 0 None Normal AC None E Green LED operation sensing constantly on no CO and with a good battery tk Lb flashes One quick AC powered and Install or replace 9V SSS alternately with beep every low or missing battery any number 60 seconds battery Red LED flashes every 60 seconds Eelam A steady display of 4 quick beeps Alarm condition Refer to What to do fee CO concentration 5 seconds Dangerous When the Alarm from 30 999 Red silence concentrations of Sounds inside front LED flashes with beeps Amber repeating CO detected cover LED shows initiating alarm fla Steady CO 4 quick beeps Another Refer to What to do EIS Red LED flashes with 5 seconds interconnected CO When the Alarm beeps Amber LED silence alarm is warning of Sounds inside front NOT illuminated repeating a CO condition cover en Fire 3 long beeps Interconnected Evacuate by your Uae Red LED flashes 1 secon smoke alarm escape plan with beeps silence repeat warning of a ing smoke fire condition 7 Model KN COP IC with digital display Operating Characteristics LED Display Shows Alarm
8. AC Quick Connector through the center hole in the mounting plate and secure the bracket making sure that the mounting screws are positioned in the small ends of the keyholes before tightening e Plug the AC Quick Connector into the back of the alarm making sure hat the locks on the connector snap into the unit Push the excess wire back into the electrical box through he hole in the center of the mounting plate e Install the alarm on the mounting plate and twist the alarm in the direction of he ON arrow on the cover until the alarm ratchets into place this ratcheting unction allows for aesthetic alignment ote The alarm will mount to the AC Quick Connector bracket in 4 positions every 90 degrees Turn on the AC power The green AC Power On Indicator should be lit when he alarm is operating from AC power Pull the Battery Pull Tab yellow tab pro ruding from unit completely out of unit This will automatically connect the battery Post Locations 4 Installation Instructions Tamper Resist Feature To make this CO alarm somewhat tamper resistant a tamper resist feature has been provided Activate the feature by breaking off the four posts in the square holes in the mounting plate When the posts are broken off the tamper resist tab on the base is allowed to engage the mounting plate Rotate the alarm onto the mounting plate until you hear the tamper resist tab snap into place loc
9. Sound Unit Status Recommendation Er p Steady E One quick Unit malfunction Repare battery If Err con Er Red LED flashes every beep every oues unit has malfunrtiongd 30 seconds 30 seconds ana MUL De repacen immed ately Unit will not respond to CO Press the Peak Level but ton while unit is in Err mode to obtain error code and call Product Support line No display alternating 4 quick beeps Alarm condition Refer to What to do with display of CO 5 seconds powered on battery When the Alarm concentration every 60 silence backup Dangerous Sounds inside front seconds Red LED repeating concentrations of cover flashes with beeps every 60 secs CO detected Replace battery No display alternating None with 0 every 60 seconds Green LED flashes every 30 seconds End displayed Two quick beeps Red LED flashes two every 30 sec times every 30 seconds onds JI70 Cao G eee ENO Normal operation Verify AC power is after first 4 minutes restored as soon as of 9 V battery possible to conserve operation Unit battery monitoring for CO Replace battery End of unit life See End of Life Notification in Maintenance Section 7 Model KN COP IC with digital display Operating Characteristics Peak Level Memory model KN COP IC only When the Peak Level button is pressed and held the display shows the highest CO reading taken by the CO alarm since its last Peak Level
10. accident unreasonable use neglect tampering or other causes not arising from defects in material or workmanship This warranty extends to the original consumer purchaser of the product only Warranty Disclaimers Any implied warranties arising out of this sale including but not limited to the implied warranties of description merchantability and fitness for a particular purpose are limited in duration to the above warranty period In no event shall the Manufacturer be liable for loss of use of this product or for any indirect special incidental or consequential damages or costs or expenses incurred by the consumer or any other user of this product whether due to a breach of contract negligence strict liability in tort or otherwise The Manufacturer shall have no liability for any personal injury property damage or any special incidental contingent or consequential damage of any kind resulting from gas leakage fire or explosion Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Some states do not allow the exclusion or limitation of consequential or incidental damages so the above limitations or exclusions may not apply to you Legal Remedies This warranty gives you specific legal rights and you may also have other rights that vary from state to state Warranty Performance During the above warranty period your product will be replaced with a comparable product i
11. ackup battery if equipped is low or missing or if the unit malfunctions it will display other readings and alarm differently to alert you of specific conditions Please familiarize yourself and other family members to the difference between a CO reading and and indication signifying a problem with the unit itself A WARNING If at any time you test the alarm and it does not perform as described have it replaced immediately Smoke Alarm Indicator interconnected with CO Alarms When an interconnected Kidde smoke alarm detects smoke the Kidde CO alarm will sound a smoke fire alarm pattern of 3 long beeps fol lowed by 1 second of silence This cycle repeats as long as smoke signal persists to alert you of the condition For model KN COP IC with digi tal display The word Fire will scroll across the digital display If this happens leave the premises immediately by your escape plan and call your local fire department A WARNING This unit is not a smoke alarm and will not detect smoke or fire It will only alarm for smoke fire if it receives a signal from an interconnected Kidde smoke alarm NOTE A smoke fire alarm will override a CO alarm condition 6 Model KN COB IC Operating Characteristics Whenever the alarm is operating the green Power LED is illuminated to indicate the unit is monitoring for CO If the alarm senses dangerous lev els of CO the red Alarm LED will flash and the alarm will emit an audi ble alarm
12. dde recommends you take action to eliminate the source of CO See What to do When the Alarm Sounds inside front cover IMPORTANT Model KN COB IC does not have a digital display and does not display carbon monoxide levels in PPM If the alarm sounds it should be treated as a potentially serious condition See What to do When the Alarm Sounds inside front cover Possible Sources of Carbon Monoxide Inside your home appliances used for heating and cooking are the most likely sources of CO Vehicles running in attached garages can also produce dangerous levels of CO CO can be produced when burning any fossil fuel such as gasoline propane natural gas oil and wood It can be produced by any fuel burning appliance that is malfunctioning improperly installed or not ventilated correctly such as e Automobiles furnaces gas ranges stoves gas clothes dryers water heaters portable fuel burning space heaters and generators fireplaces wood burning stoves and certain swimming pool heaters 1 Information About Carbon Monoxide e Blocked chimneys or flues back drafts and changes in air pressure corroded or disconnected vent pipes loose or cracked furnace exchangers e Vehicles and other combustion engines running in an open or closed garage attached or near a home e Burning charcoal or fuel in grills and hibachis in an enclosed area Conditions That Can Produce Carbon Monoxide The following conditions can
13. e a house fire and a CO problem are two distinctly different situations If your smoke alarm were to alarm you would quickly be able to judge the level of danger you were in with your senses You can see and smell the smoke feel the heat see and possibly hear the fire burning You can also readily see if your smoke alarm is alarming in a non emergency situation Because your sense of sight smell hearing and touch give you information you can almost instantly judge what action to take if you hear your smoke alarm CO is an invisible odorless tasteless and non irritating gas completely undetectable to your senses That s why it is important to your safety that you have a CO alarm ts Important Warning State IMPORTANT This carbon monoxide alarm is designed to detect carbon monoxide from ANY source of combustion It is NOT designed to detect smoke fire or any other gas A WARNING Carbon monoxide alarms are not smoke alarms This carbon monoxide alarm is not a substitute for installing and maintaining an appropriate number of smoke alarms in your home This carbon monoxide alarm will not sense smoke fire or any poisonous gas other than carbon monoxide even though carbon monoxide can be generated by fire For this reason you must install smoke alarms to provide early warning of fire and to pro tect you and your family from fire and its related hazards CAUTION This alarm will only indicate the presence of carbon mo
14. e equip ment serviced immediately Note any combustion equipment no inspected by the technician and consult the manufacturer s instruc tions or contact the manufacturer s directly for more information about CO safety and the equipment Make sure that motor vehicles are not or have not been operating in a garage attached or adja cent to the residence Never restart the source of a CO problem until it has been corrected Never ignore the sound of the alarm If the alarm is sounding pressing the test reset button will terminate the alarm If the CO condition that caused the alert in the first place continues the alarm will reactivate If the unit alarms again within six minutes it is sensing high levels of CO which can quickly become a dangerous situation Welcome Note Many times throughout this User s Guide we will refer to Carbon Monoxide as CO This Kidde carbon monoxide CO alarm is an important part of your family s home safety plan This alarm has been designed and tested to detect CO buildup in a residential environment Your alarm is for use specifically in the home As an owner of a CO alarm there are some basic facts you should know about for your protection Many people think that CO alarms operate like smoke alarms Like smoke alarms CO alarms monitor the air in your home and sound a loud alarm to warn you of trouble The way you respond to a CO alarm is quite different than a smoke alarm That s becaus
15. ecifications Installation Locations Installation Instructions Alarm Characteristics KN COB IC Operating Characteristics KN COP IC with digital display Operating Characteristics Maintenance oO oan nau FW DN Limited Warranty 1 Information About Carbon Monoxide General Carbon Monoxide Information Carbon monoxide is a colorless odorless and tasteless poison gas that can be fatal when inhaled CO inhibits the blood s capacity to carry oxy gen Periodically review this user s guide and discuss your CO alarm emer gency procedure with all the members of your family Never ignore a CO alarm A true alarm is an indication of potentially dangerous levels of CO CO alarms are designed to alert you to the presence of CO before an emergency before most people would experience symptoms of CO poisoning giving you time to resolve the problem calmly Determine if anyone in the household is experiencing symptoms of CO poisoning Many cases of reported CO poisoning indicate that while victims are aware they are not well they become so disoriented they are unable to save themselves by either exiting the building or calling for assistance Also young children and household pets may be the first affected You should take extra precautions to protect high risk persons from CO exposure because they may experience ill effects from CO at levels that would not ordinarily affect a healthy adult Symptoms of CO Poisoning The following co
16. ed by 5 seconds of silence followed by 4 quick beeps For model KN COP IC with digi tal display The display will show three eights and then show a num ber usually around 200 The red LED will flash along with the beeps and the amber LED will illuminate Within several seconds the unit will return to monitor for CO If interconnected to Kidde smoke alarms pressing the Test Reset button on the CO alarm will have no effect on the smoke alarms The smoke alarms will not be tested and will not alarm However when pressing the Test button on an interconnected smoke alarm the CO alarm will emit a Smoke Fire audible and visual alarm pattern of 3 long beeps 1 second of silence repeated NOTE You do not need to press the Test button to take a CO reading Low Battery HUSH CONTROL When the battery needs to be replaced the unit will produce a low battery chirp once per minute The Low Battery HUSH feature allows you to press the button on the alarm producing the warning and disable the chirp for a random period of up to 12 hours This gives you a chance to replace the battery at a more convenient time without sacrificing your safety by disconnecting the alarm from power During this Low Battery HUSH period your alarm is performing normally and is not desensitized Battery Replacement These CO alarms are not battery operated However these alarms are equipped with 9 volt battery backup the 9 volt battery is
17. f the defective product is returned in a postage paid package to the following address Kidde Customer Service Department 1016 Corporate Park Drive Mebane NC 27302 USA together with proof of purchase date Please include a note describing the problem when you return the unit The replacement product will be in warranty for the remainder of the original warranty period or for six months whichever is longer Other than the cost of postage no charge will be made for replacement of the defective product In many cases the quickest way to exchange your alarm is to return it to the original place of purchase If you have questions call Kidde customer service department IMPORTANT Do not remove unit back cover Back cover removal will void warranty Your Kidde Carbon Monoxide Alarm is not a substitute for property disability life or other insurance of any kind Appropriate insurance coverage is your responsibility Consult your insurance agent Also Kidde makes no warranty express or implied written or oral including that of merchantability or fitness for any particular purpose with respect to the battery The above warranty may not be altered except in writing signed by both parties hereto QUESTIONS OR FOR MORE INFORMATION Call our Product Support Line at 1 800 880 6788 or contact us at our website at www kidde com Kidde Kidde 1016 Corporate Park Drive Mebane NC 27302
18. han 100 F 37 8 C such as crawl spaces attics porches and garages e Do not install within 5 ft of heating or cooking appliances Kidde recommends 15 ft to prevent nuisance alarms e Do not install near vents flues chimneys or any forced unforced air ventilation openings e Do not install near ceiling fans doors windows or areas directly exposed to the weather e Do not install in dead air spaces such as peaks of vaulted ceilings or gabled roofs where CO may not reach the sensor in time to provide early warning e Do not install on a switched or dimmer controlled outlet e Do not install this unit near deep cell large batteries Large batteries have emissions that can cause the alarm to perform at less than opti mum performance 3 Installation Locations e Do not obstruct the vents located on the alarm Do not place the alarm where drapes furniture or other objects block the flow of air to the vents 4 Installation Instructions Interconnecting CAUTION Kidde Fyrnetics Lifesaver Kidde Nighthawk Pyrene alarms and accessories can only be interconnected with other Kidde alarms and accessories Connection of these devices to another manufactures interconnect system or connection with equipment from another manufacturer into an existing Kidde interconnect system could result in nuisance alarming failure to alarm or damage to one or all of the devices in the interconnect system e When compatib
19. ile in an error condition CO alarms can only sense CO that reaches the unit s sensor It s possible that CO may be present in other areas without reaching the alarm The rate and ability that which CO reaches the alarm may be affected by e Doors or other obstructions e Fresh air from a vent an open window or other source e CO being present on one level of the home and not reach a CO alarm installed on a different level For example CO in the basement may not reach an alarm on the second level near the bedrooms For these reasons we recommend you provide complete coverage by placing a CO alarm on every level of the home Please carefully read all information in sections 2 and 3 on properly installing this CO alarm CO alarms should not be used to detect the presence of natural gas methane propane butane or other combustible fuels Instruct children never to touch unplug or otherwise interfere with the alarm Warn children of the dangers of CO poisoning 2 Product Features and Specifications Amber Initiating Green Alarm LED Power LED Red Alarm LED Green Power LED Amber Initiating Alarm LED Test Reset Button Test Reset Button Peak Level Button Digital Display AC Connector Pins Tamper Resist Battery Feature Compartment IMPORTANT Ten 10 years after the initial power up this alarm will beep two times every 30 seconds to indicate that
20. it is time to replace the alarm Replace the alarm immediately It will not detect CO in this condition See Maintenance Section for more information regarding End of Life Notification To help identify the date to replace the alarm a label has been affixed to the side of the alarm Write the replace by date ten years from power up in a permanent marker on this label 2 Product Features and Specifications Temperature Operating Range 40 F 4 4 C to 100 F 37 8 C Humidity Operating range 10 95 non condensing Audible Alarm 85 dB at 10 3 4 0 5 KHz pulsing alarm Sensor Electrochemical Power 120 volts AC 60 Hz 60 mA max 9 volt battery back up Accuracy of Digital Display Model KN COP IC only 30 999 PPM 30 when measured in conditions of 80 F 10 F atmospheric pressure 10 and 40 3 relative humidity Display readings may vary slightly depending on changes in the ambient condition temperature humidity and the condition of the sensor Alarm Response Times 70 PPM 60 240 min 150 PPM 10 50 min 400 PPM 4 15 min Interconnection with Other Alarms This Kidde CO alarm can be used as a single station alarm or intercon nected with other Kidde alarms This alarm can be interconnected direct ly with these Kidde models lon smoke alarm models 1235 1235CA 1275 1275CA 1276 1276CA 1285 1285CA 112020 i12040 i12060 i12080 i12020CA i112040CA i12060CA Photo s
21. ix remote signaling devices and or relay modules e The maximum wire run distance between the first and last unit in an interconnected system is 1000 305 m e Make certain alarms are wired to a continuous non switched power line NOTE Use standard UL Listed household wire as required by local codes available at all electrical supply stores and most hardware stores FUSE OR CIRCUIT BREAKER CONNECTOR Optional Accessory First CO Alarm Additional See list of compatible CO Alarm Kidde devices Interconnect Wiring Diagram Wiring The diagram above illustrates interconnection wiring Improper connec tion will result in damage to the alarm failure to operate or a shock hazard CAUTION Turn off the main power to the circuit before wiring the alarm Wires on the AC Quick Connector Alarm Harness Black Connected to live L side of AC line White Connected to neutral N side of AC line Red Connected to interconnect lines red wires of other units in a multiple station set up 4 Installation Instructions Mounting e After selecting the proper location for your CO Alarm and wiring the AC Quick Connector harness attach the mounting plate to the elec rical box To ensure aesthetic alignment of the alarm with the hall way or wall the A line on the mounting plate must be parallel with he hallway when ceiling mounted or horizontal when wall mounted Pull the
22. king the alarm Using the tamper resist feature will deter children and others from removing the alarm To remove the alarm press on the tamper resist tab and rotate the alarm off of the mounting plate Tamper Resist Tab Important Labels Provided Two labels have been provided that have important information on what to do in case of an alarm Add the phone number of your emergency service provider in the space provided Place one label next to the alarm after it is mounted and one label near a fresh air source such as a door or window 5 Alarm Characteristics Carbon Monoxide Alarm Indicator When the alarm senses a dangerous level of CO the unit will emit a loud alarm pattern The alarm pattern is 4 quick beeps followed by 5 seconds of silence This cycle repeats as long as a dangerous CO condi tions exist The red Alarm LED will flash the same pattern and the PPM will be displayed on alarms with digital displays AN WARNING When powered by battery backup only after four minutes the alarm will sound and flash only once every minute until the alarm is reset or the CO is eliminated If this unit is interconnected with other Kidde CO alarms the amber LED Initiating Alarm of the unit which first detected the CO will light and remain on until reset The other interconnected CO alarms will also alarm to warn you that CO was detected 5 Alarm Characteristics If interconnected to other Kidde alarms and the b
23. le Kidde smoke alarms and heat alarms are interconnected to your CO alarm they will only respond to a smoke or heat related event e When mixing Kidde alarms which have battery back up with models without battery back up be advised that the models without battery back up will not function during an AC power failure e For alarms that are being used as single station alarms do not connect the red wire to anything Leave the red wire insulating cap in place to make certain that the red wire cannot contact any metal parts or the electrical box e The appropriate power source is 120 Volt AC Single Phase supplied rom a non switchable circuit which is not protected by a ground ault interrupter e All interconnectable alarms should be installed on a UL Listed or recognized junction box All connections should be made by a qualified electrician and must conform to article 760 of the U S ational Electrical Code NFPA 72 and or any other codes having jurisdiction in your area e When alarms are interconnected all interconnected units must be powered from a single circuit e A maximum of 24 Kidde devices may be interconnected in a multiple station arrangement The interconnect system should not exceed the NFPA interconnect limit of 12 smoke alarms and or 18 alarms total smoke CO smoke CO combination heat etc 4 Installation Instructions e With 18 alarms interconnected it is still possible to interconnect up to a total of s
24. mmon symptoms are related to CO poisoning and should be discussed with ALL members of the household Mild Exposure Slight headache nausea vomiting fatigue often described as flu like symptoms Medium Exposure Severe throbbing headache drowsiness confusion fast heart rate Extreme Exposure Unconsciousness convulsions cardio respiratory failure death If you experience even mild symptoms of CO poisoning consult your doctor immediately 1 Information About Carbon Monoxide Carbon Monoxide PPM Levels model KN COP IC with digital display only Model KN COP IC is equipped with a digital display that shows levels of CO displayed in PPM parts per million Learn the difference between dangerous high mid and low levels Dangerous Levels When someone is experiencing symptoms of CO poisoning and CO readings are generally above 100 PPM Anytime someone is experiencing the symptoms of CO poisoning this should be treated as an emergency See What to do When the Alarm Sounds inside front cover High Levels Generally above 100 PPM with no one experiencing symptoms This should be treated as an urgent situation See What to do When the Alarm Sounds inside front cover Mid Levels Generally between 50 PPM to 100 PPM This should be cause for concern and should not be ignored or dismissed See What to do When the Alarm Sounds inside front cover Low Levels Generally below 50 PPM Ki
25. moke alarm models PE120 PE120CA Photo lon combination alarms PI2010 PIZ010CA Heat alarm models HD135F HD135FCA Carbon monoxide lon smoke alarm models KN COSM IB KN COSM IBCA Carbon monoxide alarm models KN COB IC KN COP IC KN COB ICB KN COP ICB Relay models CO120X SM120X Strobe Light models SL1771 3 Installation Locations Recommended Installation Locations CO alarms should be mounted in or near bedrooms and living areas It is recommended that you install a Kidde CO alarm on each level of your home When choosing your installation loca stoned tions make sure you can hear the alarm from all sleeping areas If you install only one CO alarm in your home install it near bedrooms not in the basement or furnace room Recommended Locations e When wall mounting place out of reach of children Under no cir cumstances should children be allowed to handle the CO alarm Placing the alarm at eye level allows for optimum monitoring of the digital display Locations To Avoid IMPORTANT Improper location can affect the sensitive electronic com ponents in this alarm To avoid causing damage to the unit to provide optimum performance and to prevent unnecessary nuisance alarms e Do not install in kitchens garages or furnace rooms that may expose the sensor to substances that could damage or contaminate it e Do not install in areas where the temperature is colder than 40 F 4 4 C or hotter t
26. noxide at the sensor Carbon monoxide may be present in other areas Important Warning State ts A WARNING This product is intended for use in ordinary indoor locations of family living units It is not designed to measure compliance with Occupational Safety and Health Administration OSHA commercial or industrial standards It is not suitable for installation in hazardous locations as defined in the National Electric Code The installation of this device should not be used as a substitute for proper installation use and maintenance of fuel burning appliances including appropriate ventilation and exhaust sys tems It does not prevent CO from occurring nor can it solve an existing CO problem A WARNING This device is designed to protect individuals from acute effects of carbon monoxide exposure It may not fully safe guard individuals with specific medical conditions If in doubt consult a medical practitioner Individuals with medical problems may consider using warning devices which provide audible and visual signals for carbon monoxide concentrations under 30 PPM This carbon monoxide alarm requires a continuous supply of elec trical power it will not work without power Models without battery backup will not operate during power failure This alarm has not been investigated for carbon monoxide detec tion below 70 PPM Contents of This User s Guide 1 Information About Carbon Monoxide Product Features and Sp
27. pattern Operating and Alarm Characteristics Function LED Display Alarm Sound Unit Status Recommendation Norma Green LED None Normal AC None Operation constantly on operation sensing no CO and with a good battery Norma Green LED flashes None Normal DC Verify AC power is Operation every 30 seconds operation on 9V restored as soon as attery backup ossible to conserve attery Replace battery Carbon ed LED flashes 4 quick beeps Alarm condition efer to What to do monoxide with beeps 5 seconds Dangerous When the Alarm alarm Amber LED shows silence concentrations of Sounds inside front initiating alarm repeating CO detected cover Smoke ed LED flashes 3 long beeps Receiving signal Evacuate by your fire alarm with beeps 1 second rom an intercon escape plan silence nected smoke alarm repeating detecting smoke Low ed LED flashes One quick AC powered and nstall or replace 9V battery every 60 seconds beep every 60 low or missing battery seconds attery Error ed LED flashes One quick Unit is in error eplace battery service every 30 seconds beep every 30 condition if Error continues alarm seconds unit has malfunc tioned Replace Error ed LED Constant Very low battery or immediately Unit will constantly on alarm unit malfunction not respond CO Normal ed LED flashes 4 quick beeps Normal operation CO not detected Test Reset with beeps 5 seconds when
28. result in transient CO situations e Excessive spillage or reverse venting of fuel burning appliances caused by outdoor ambient conditions such as wind direction and or veloci ty including high gusts of wind heavy air in the vent pipes cold humid air with extended periods between cycles e Negative pressure resulting from the use of exhaust fans e Simultaneous operation of several fuel burning appliances competing for limited internal air e Vent pipe connections vibrating loose from clothes dryers furnaces or water heaters e Obstructions in or unconventional vent pipe designs which can amplify the above situations e Extended operation of unvented fuel burning devices range oven fireplace etc e Temperature inversions which can trap exhaust gases near the ground e Vehicle idling in an open or closed garage or near a home To be safe know the possible sources of CO in your home Keep fuel burning appliances and their chimneys and vents in good working condi tion Learn the early symptoms of exposure and if you suspect CO poi soning move outside to fresh air and get emergency help Your first line of defense is an annual inspection and regular maintenance of your appliances Contact a licensed contractor or call your local utility compa ny for assistance Information About Carbon Monoxide Alarms What They Can and Cannot Do CO alarms provide early warning of the presence of CO usually before a heal
29. thy adult would experience symptoms This early warning is possible however only if your CO alarm is located installed and maintained as described in this guide 1 Information About Carbon Monoxide Because carbon monoxide is a cumulative poison long term exposures o low levels may cause symptoms as well as short term exposures to high levels This Kidde unit has a time weighted alarm the higher the level of CO present the sooner the alarm will be triggered This CO alarm can only warn you of the presence of CO It does not prevent CO from occurring nor can it solve an existing CO problem If your unit has alarmed and you ve provided ventilation by leaving your windows and doors open the CO buildup may have dissipated by the ime help responds Although your problem may appear to be emporarily solved it s crucial that the source of the CO is determined and that the appropriate repairs are made This CO alarm is designed to act as a monitor it is not designed for use as a short term testing device to perform a quick check for the presence of CO CO alarms have limitations Like any other electronic device CO alarms are not fool proof CO alarms have a limited operational life You must test your CO alarm weekly because it could fail to operate at any time If your CO alarm fails to test properly or if its self diagnostic test reveals a malfunction immediately have the unit replaced This alarm will not monitor CO levels wh
30. to supply short term back up during a power outage When replacing the battery use one of the following approved brands e Duracell MN1604 or MX1604 e Energizer 522 e Goldpeak 1604A These batteries can be purchased where you bought the alarm or at a local hardware store Use of a different battery may have a detrimental effect on the alarm operation The 9 volt battery is not rechargeable If the 9 volt battery is missing disconnected or if the battery s power is low a red LED flash will occur once every 60 seconds accompanied by an audible beep If this happens the battery must be replaced For model KN COP IC with digital display Lb will be displayed alternately with the current CO reading once every second IMPORTANT Constant exposures to high or low humidity may reduce battery life A good safety measure is to replace the battery at least once a year or at the same time as you change your clocks for daylight saving time End of Life Notification Ten 10 years after uni pressing the Test Reset o two days giving you The display will alterna remind you to replace be silenced The alarm but all other functiona Alarm Removal f the tamper resist fea is first powered this alarm will beep two times every 30 seconds and display End on digital models to indicate that it is ime to replace the alarm see Alarm Removal section for instructions By button the audible notification will be silenced for up
Download Pdf Manuals
Related Search