Home

Kathrein UFS 710si User's Manual

1. a 80 SHORT TECHNICAL GUIDE sis een 84 EED A A 86 TROUBLE SOO TING nennen 87 frs u 87 DANGER 4 WARNING CAUTION SAFETY INSTRUCTIONS IMPORTANT NOTES This page contains important information about the operation installation location and connection of the unit Read these instructions carefully before starting to use the unit Mains cable Make sure that the mains cable power supply cable is not damaged Units with a damaged mains cable must be disconnected from the mains disconnect mains connector and repaired by a qualified engineer before setup Only use the power pack supplied if available Risk of death due to electric shock Cleaning Disconnect the mains connector before cleaning the unit Only use a dry cloth for cleaning and only clean the outer surface Never open the unit Touching the parts inside the unit carries a risk of death due to electric shock Playing children Make sure that children do not push any objects into the ventilation slots Risk of death due to electric shock Earth connection The antenna system must be earthed as specified or equipotentially bonded EN 60728 11 and any national regulations must be complied with Danger due to surge voltages lightning strikes Mains voltage Only operate the unit
2. 57 SEARCH CHANNELS CHANNEL SEARCHN T T 58 AUTOMATIC CHANNEL SEARCH nennen 58 MANUAL CHANNEL SEARCH ernennen 60 CHANNEL SCAN WITH SERVIC END ans 62 PARENTAL CONTROL 64 LOCK mls ernennen nee REEN ae 64 LOCK SET TOP BOX ee ea 64 DEFINE NEVW PINCODE U ee en ne ee 65 SETTINGS u u a EEE Era 66 DD ee 67 CUSTOMIZE SCREEN MEN ee ae nes 68 DATE NDO TIME ee en Eee a ee ee sen 70 COMMON INTERFACE ee ee 70 ANTENNA CONFIGURATION ee re 70 SERVICE MENU ae EIER 71 UPDATE SOFTWARE uuu uu ne a En 71 RESTORE FACTORY DEFAULT SEEN Se a ee 73 CONNECTING UP THE VIDEO PVR 74 REC ORDIN en na ne ert 74 BA 74 USING THE FRONT PANEL ul IILI uuu 75 TECHNICAL APPENDIK uuu aaa na a nee Renee Tune EEE RUNTER 76 FEAIUPES nee nen near iMd nenn Teen 76 SCART SOCKET ASSIGNMENT zen ee ren 78 VHS S VHS SWITCHING aa nase 78 CONNECTION EXAMPLE 79 EXAMPLES single cable systems
3. 35 CHANNEL MESSAGES cccccecececcsseceecececeecececsecececsevacecavaceesavaceecavacsecavaceecsvcesvstisesvavesesvatereess 35 PROGRAMME INFORMATION cssesecccsececcsceceecececeeseeeceesececsecaceceecateceavaceccevatrcevatersavacereeees 35 CALLING UP THE OPTIONS CHANNEL cccccecececeecececcececeecececeecececcereceacsvecessetecertsvereseateteres 35 OPTION SELECTION 36 ERROR SIGNALLING 36 CHANNEL LIST TV RADIO 0 ccceccscecececcececeecececeevecececececcavececcevaceacavaceesavecestatesestatesessatererss 36 EPG ELECTRONIC PROGRAMME GUIDE U U a 38 CALLING UP THE EPG cccccececcccececeecsseceecececcecacecsevacecsecaceccavaceecavacsecavacescavcestatisestateteseatereess 38 CURRENT VIEW ann aaa 39 PREVIEW VIEW PROGRAMME LISTINGS aI aaa 40 CATEGORIES VIEW cccccccccscececcecececcecececcececcacecsesaceceacasecsacansceacanseeacacscacceeeaesestatesescaneseces 41 SEARCH FUNCTION cceccccesececcsceceecsceceecececsesacecsevaceecavaceesavacsecevacecevecescavacessatesestatetesvavereees 42 ADDITIONAL INFORMATION i BUTTON tnter retten 43 RECORDING TIMER 2 c cececcececescosececsececeescececeesececsesacecsevarecsecaceccesaceccevaceecevaceecsvateecevaceseetes 44 RECORD ONCE iriserai na aa eE EEEE uci petebant ri a utt o tc IR bete ive ptas Ee qaraqna 45 RECORD DAILY CRM 9 45 RECORD WEEK
4. Current affairs Berlin Hotel Adlon feiert Geburtstag Rheinland Pfalz Wanderarbeiter aus Sachsen Harz Urlaub f r Naturliebhaber Duisburg Zoopraktikum f r Jedermann EB Vorherige N chste Sendung F Weitere intormationen zur ck Record The additional information available for a programme is displayed its own window pressing the v button if available you can call up further additional information on the selected programme The buttons enable you to display the additional information for the preceding or following programmes in the order of the previously selected list see header This always assumes that the data has been supplied by the channel provider Using the red dot button you can load the selected programme into the recording settings see item Recording Press the 3 button or the button to exit the additional information 43 EPG ELECTRONIC PROGRAMME GUIDE RECORDING TIMER The red dot button allows you to set up programme at any time for recording on an external recorder The programme to be recorded can be selected in any ofthe EPG views provided the red dot button appears at the bottom of the screen display Programme present in the EPG Select the desired programme and press the red dot button The following display appears example Programme not present in the EPG Select any programme on the channe
5. buttons to set the brightness of the receiver front display Select the most comfortable setting for the ambient lighting FRONT DISPLAY IN STANDBY Use the buttons to set whether the receiver front display should be switched on or off in stand by mode display of time ADJUST MENU ON TV Press the button to align the on screen displays on the TV screen Now you can use the cursor buttons o to determine the position of the on screen display When you have achieved the desired position press the button to fix the desired position EXIT 69 SETTINGS DATE AND TIME Wednesday 06 06 2007 5 15 51 06 06 2007 15 51 Clock Local time offset Use the buttons to set the time zone variation from UTC formerly GMT e g for Germany 1 hour Use the Av buttons to switch to the Automatic clock change field Automatic clock change Use the o0 buttons to select whether the receiver should automatically change over to and from summer and winter time If On is selected the receiver automatically sets itself to the right time If Off is selected the field for manual selection of summer and winter time is displayed below Press the buttons to perform the setting Press the button to exit menu again COMMON INTERFACE See Common Interface section ANTENNA CONFIGURATION See First Installation section pages 14ff 70 SERVICE MENU Sel
6. ERA 14 ERA 14 AxESU 34 The receiver must be programmed for single cable commands Overvoltage protection KAZ 11 KAZ 12 81 TECHNICAL APPENDIX EXR 1581 2581 Single cable matrices Sat IF 950 2150 MHz KATHREIN Twin Single Single ESU 33 ge Sai C ESU 33 9 Twin Single Single ESU 33 Eee 6 ESU 33 9 Twin Single Single ESU 33 Eee CE ESU 33 i Twin Single Single ESU 33 ge 9 ESU 33 Gi ERA 14 ERA 14 The receiver must be programmed for single cable commands Overvoltage protection KAZ 11 KAZ 12 82 TECHNICAL APPENDIX 908 Single cable matrix IN IN Sat IF lt 950 2150 MHz eee ESU 33 ESU 33 ESU 33 ESU 33 ERA 14 1 1 Single Single Single Single ELS ESU 33 ESU 33 ERA 14 2 Twin Twin The receiver must be programmed for single cable commands Overvoltage protection KAZ 11 KAZ 12 83 SHORT TECHNICAL GUIDE CHANNEL PACKAGE The channel package for a digital transponder normally includes several TV and radio channels Each channel package has a fixed assignment for the transponder transmission frequency for polarisation horizontal or vertical for the symbol rate and for the Viterbi rate or error rate DISEQC DISEqC M Digital Satellite Equipment Control is a communication system between a satellite receiver master and the peripheral
7. When all settings have been made press the button to save the recording settings You can view the recoding schedule in the Timer List view of the EPG see item Plan recording 44 EPG ELECTRONIC PROGRAMME GUIDE RECORD ONCE Use the gt buttons to select the recording mode once see screenshot item Recording Timer Use the Av buttons to switch to the selection field Date and use the buttons to select the desired recording date Use the Av buttons to switch to the selection field Start and use the GP buttons or the numeric pad to select the desired recording starting time Use the Av buttons to switch to the selection field End and use the buttons or the numeric pad to select the desired recording ending time When all settings have been made press the button to save the recording settings You can view the scheduled recording in the Timer List view ofthe EPG see item Plan recording RECORD DAILY Use the gt buttons to select the recording mode daily see screenshot below Use the 4 buttons to switch to the selection field Start and use the 4 gt buttons or the numeric pad to select the desired recording starting time Use the Av buttons to switch to the selection field End and use the o0 buttons or the numeric pad to select the desired recording ending time p Mon 10 00 f 50 Das Erste When all settings have been ma
8. buttons to select Yes save changes and confirm by pressing the button Now press the 8 green button The receiver will automatically display the selection menu for the channel search Continue by selecting the item Execute Channel search connection to the single cable system could be established you will receive the message Registration was abortive Check your settings and if necessary call for expert help 27 FIRST INSTALLATION Single cable system Manual Selection 4 subscriber When the 4 subscriber single cable switching matrix is being used it is essential that the LNB is set to Universal Transmission channel Use the o0 buttons to select a free available transmission channel A maximum of four transmission channels are available 1284 1400 1516 and 1632 MHz Test connection When you have set a free transmission channel press the a buttons to switch to the Test Connection selection field and press the button The receiver now tests whether a connection to the single cable system can be established or not As soon as the receiver has established a connection to the single cable system you will see the following display Press the button to acknowledge this display Then press the button You will be asked whether you wish to save the changes Use the AYv buttons to select Yes save changes and confirm by pressing the but
9. Stop recording The button symbols shown here can also be found playback stop in the description of the operating steps 11 REMOTE CONTROL REMOTE CONTROL RC 660 The RC 660 remote control supports up to four devices which are supplied with the RC 660 as standard as well as the receivers of the UFD 5xx not UFD 552 554 558 and UFD 4xx families First switch all receivers off at the power switch To configure a receiver to an infrared code Switch on the relevant receiver On the remote control simultaneously press address 1 en 9 O Then switch the receiver off again at the power switch and do the same for the other units em 9 2 for the second receiver 9 3 for the third receiver and 9 4 for the fourth receiver Make sure only one receiver is on at a time To switch the remote control to an infrared code When you have configured all receivers to their infrared code do the following to switch between units on the remote control For operating the first receiver address 1 press m for the second receiver for the third receiver and for the fourth receiver is red Kathrein UFD 5xx code for remote control RC 400 The 600 and RC 650 remote controls are not interchangeable 12 FIRST INSTALLATION General Before using your unit for the first time read the Safety Instructions and Connection and Setup sections The Connect
10. and use the lt J gt buttons to enter the desired recording day Press the button to fix the selection the day will be shown in red letters If necessary the receiver will suggest some days to you you can accept these suggestions or deactivate them again using the cursor buttons and pressing the button once Use the Av buttons to switch to the selection field Start and use the GP buttons or the numeric pad to select the desired recording starting time 46 EPG ELECTRONIC PROGRAMME GUIDE Use the Av buttons to switch to the selection field End and use the buttons or the numeric pad to select the desired recording ending time TV Program Guide O ID d 10 00 10 03 external recorder Mon Tue Wed Thu Fri 09 58 10 08 Recording mode i Pian recording When all settings have been made press the button to save the recording settings You can view the recording in the Timer List view of the EPG see item Plan recording SERIES RECORDING Series recording depends on the EPG data being kept up to date at all times This depends on the receiver being automatically updated at 03 00 see section Important Information Switching off the receiver and updating the EPG Updating is important because it enables the receiver to recognise for purposes of recording any changes to scheduled transmission times of the series provided these were incorporated in the E
11. O yv I x W lt 4 10 When fitting connector make sure that no wires from braid are touching the inner conductor so no short circuit can occur The quality of the reception signal depends on this connection RECEPTION REQUIREMENTS Make sure that your own satellite antenna system is equipped at least with a universal LNB for digital reception in the high band range RECEPTION SYSTEM PRESETS The presets for the control signals have been made for standard reception systems i e 14 18 V for polarity reversal and 22 kHz switching signal for low high band changeover on multi feed reception systems CONNECTION AND SET UP TV AND VIDEO RECORDER CONNECTION Connect the satellite receiver TV Scart socket and the TV set using a Scart cable see Connection Example If your TV has a stereo feature you can receive the sound in stereo via the Scart connection Use a further Scart cable to connect the satellite receiver VCR Scart socket to the video recorder PVR For system reasons the same video signals are to be found at the TV Scart socket as at the video cinch output If you are recording using an external video recorder remember not to operate the receiver during recording otherwise all the on screen displays will appear on your recording AUDIO CONNECTION If you want to play the sound on your hi fi system connect the audio cinch sockets to the input sockets on the
12. X Video earth 17 X X Blanking signal earth 18 X X Video output FBAS Y 19 X X Video input 20 X Connector shield 21 X X VHS S VHS SWITCHING The Scart sockets are switchable between VHS and S VHS The switch is made by selecting Mainmenu Settings TV Video and Audio VHS RGB The red signal is connected to terminal 15 the composite colour output to terminal 19 S VHS The Y output is connected to pin 19 the output to pin 15 78 TECHNICAL APPENDIX CONNECTION EXAMPLE Dolby Digital system Digital audio AC 3 s Cinch Scart Elektroschock Gefahr KATHREIN IF OUTPUT 1 DATA 230V 50Hz z H max 25W PVR VCR Cinch Infra red receiver optional Hi fi system 79 TECHNICAL APPENDIX EXAMPLES single cable systems EXR 501 551 552 Single cable switching matrices UAS Sat IF 950 2150 MHz 4 X single ESIEXR 551 2 x twin receivers ESU 33 ESU 33 ESU 33 ESU 33 ERA 14 Single Single Single Single mm Cm Erma ESU 33 ESU 33 ERA 14 C 9 a nc Twin Twin Ss ee war The receiver must be programmed for single cable commands Overvoltage protection KAZ 11 KAZ 12 80 D TECHNICAL APPENDIX UAS 481 Single cable feed system
13. by selecting the item Execute Channel search no connection to the single cable system could be established the following display appears Check your settings and if necessary call for expert help 25 FIRST INSTALLATION Single cable system Manual Selection EXR 552 When the EXR 552 single cable switching matrix is being used it is essential that the LNB is set to Universal Transmission channel Use the buttons to select free available transmission channel A maximum of two transmission channels are available 1400 and 1516 MHz Test connection When you have set a free transmission channel press the a buttons to switch to the Test Connection selection field and press the button The receiver now tests whether a connection to the single cable system can be established or not As soon as the receiver has established a connection to the single cable system you will see the following display Press the button to acknowledge this display Then press the button You will be asked whether you wish to save the changes Use the AYv buttons to select Yes save changes and confirm by pressing the button Now press the green button The receiver will automatically display the selection menu for the channel search Continue by selecting the item Execute Channel search If no connection to the single cable system could be established you will receive t
14. connection to the single cable system could be established the following display appears Check your settings frequency and transmission channel and if necessary call for expert help 24 FIRST INSTALLATION Single cable system Manual Selection UAS 481 or 551 When the UAS 481 single cable feed system is being used it is essential that the LNB is set to Wideband When the EXR 551 single cable switching matrix is being used it is essential that the LNB is set to Universal Transmission channel Use the GP buttons to select a free available transmission channel A maximum of four transmission channels are available 1400 1516 1632 and 1748 MHz Test connection When you have set a free transmission channel press the N buttons to switch to the Test connection selection field and press the button The receiver now tests whether a connection to the single cable system can be established or not As soon as the receiver has established a connection to the single cable system you will see the following display Press the button to acknowledge this display Then press the button You will be asked whether you wish to save the changes Use the N buttons to select Yes save changes and confirm by pressing PIP the button Now press the green button The receiver will automatically display the selection menu for the channel search Continue
15. found channels are identified with the designation new after the channel name After completion of the search you will see the following message example 61 SEARCH CHANNELS CHANNEL SEARCH Wednesday 06 06 2007 15 43 New TV Channels 334 New Radio Channels 179 Press the button You will be asked whether you wish to save the changes or not Selection is performed using the Av buttons and is confirmed using the button If you select Yes save changes the newly found channels will be added to the end of the channel list Then press the button to exit the menu The channel list is called up on to the TV screen by pressing the button see also section On screen displays Channel list TV Radio CHANNEL SCAN WITH SERVICE ID The Av buttons allow you to select different sets of parameters for the search Satellite Use the oo buttons to select the satellite that is transmitting the channels to be scanned Make sure your reception system is aligned to the selected satellite 62 SEARCH CHANNELS CHANNEL SEARCH Press the v button to move to the next selection item Transponder Frequency Use the GP buttons or the numeric keypad to select the transponder frequency on which the channel being sought is transmitted At the bottom right of the screen display the receiver shows the current signal strength and signal quality of the selected transponder Press the v button to move to
16. hi fi system using an appropriate cable see Connection Example OPTICAL ELECTRICAL DIGITAL OUTPUT The fibre optic output and the electrical digital output are intended for the connection of a Dolby Digital system see Connection Example INSERTING BATTERIES INTO THE REMOTE CONTROL Remove the cover on the rear of the remote control Insert the two supplied batteries into the remote control Ensure correct polarity of the batteries the and markings are indicated inside the battery compartment Slide the cover back into the housing until it locks in place 10 REMOTE CONTROL Sound on off Switch on input digits for channels timer etc Standby Videotext Teletext yellow Call up Channel Options sound subtitles selection S blue Switch between TV radio 1 Access Channel Notification Info AV mode Channel selection up down Input confirmation call up Channel List 9181016 Cursor buttons Access EPG Electronic Programme Guide Call up Main Menu exit the menu and return to the TV picture Call up favorites selection m PIP B green Current view in the EPG Volume Exit menu step by step Changing channel in the programme guide EPG Transparent videotext Currently not used Changing channel in the programme guide EPG red Recording in EPG editing KATHREIN in channel list
17. order of the overall channel list the channels can also be selected by inputting digits with the keypad you remain however in Preview The 6 button allows you to scroll backwards and forwards a day at a time Using the red dot button you can load the selected programme into the recording settings see item Recording 40 EPG ELECTRONIC PROGRAMME GUIDE CATEGORIES VIEW The Categories view can be called up at any time in EPG by pressing the 9 blue button Wednesday 06 06 2007 15 02 Movie gt L 06 06 07 14 45 16 15 Movie In the Categories view you can see all programmes sorted by category and starting time The following categories are available for selection Movies Series Sport Children s programmes Chat shows News Magazines Reportage Art Culture Science Education Music Leisure and Adult programmes Programmes can be assigned to the above categories only if the EPG data has been supplied by the channel provider Select the required category using the buttons You can then use the cursor buttons Jv 906 to select the desired category and if available you can use the 3 button within each category to call up further information on the desired programme The 6 button allows you to scroll backwards and forwards day at a time Using the red dot button you can load the selected programme into the recording settings see it
18. radio programmes simultaneously on a single transmission frequency If a programme provider is broadcasting several TV channels via a digital transponder we refer to the provider s channel package The terms digital transponder and channel package have the same meaning VIDEO BIT RATE The video bit rate describes the quantity of data from the digitised video signal that is transmitted per second VITERBI RATE The Viterbi rate code rate error rate characterizes the error protection used by the programme provider The DVB standard provides the following values 1 2 2 3 3 4 5 6 7 8 85 SHORT TECHNICAL GUIDE GLOSSARY Output for Dolby Digital signal Audio output Sound output on the receiver AV programme pos Preferred programme position on TV set for Scart input LED display Display on receiver Low Noise Block Converter On Screen Display Eb No ratio Digital signal to noise ratio Analogue TV standard Muting of sound PD Short technical guide PIN Personal Identification Number RGB Video signal made up of three individual colour signals red green blue Smartcard Card from Pay TV provider to decode its channels Time shifted playback See Short technical guide UFO micro and Kathrein specific satellite signal processing systems UFO mini VCR connection Video recorder connection Viterbi rate See Short technical guide Condition
19. satellite components slaves such as LNBs multi switches rotating antenna systems It is a single master multi slave system i e there is only ever one master in the satellite system All activities start from the master DISEQC COMPONENTS If DISEGC switching matrices are cascaded the master receiver must transmit the DISEqC M signal several times so that all DISEqCTM multi switches in the cascade receive their commands These days DISEQC components slaves must be reverse compatible i e respond to the analogue switching criteria from receivers that are only equipped with H V and 22 kHz control signals A DiSEqC M switching matrix will work with analogue switching criteria until the DiSEqC M command from the master is received All analogue switching criteria are then ignored DVB MPEG 2 DVB is the abbreviation for Digital Video Broadcasting DVB S refers to the transmission method S satellite MPEG is the abbreviation for Moving Picture Experts Group a working group that formulates internationally applicable standards for the digital compression of video and audio MPEG 2 has established itself as the standard for compression of digital TV signals MPEG 2 works up to a data rate of 100 Mbit s EB NO RATIO The Eb No ratio is a measure of the signal to noise ratio of a digital signal The value is not identical to the C N value familiar from analogue reception technology At Eb No values below 5 dB reception is not
20. scanned using the buttons or the numeric keypad At the bottom right of the screen display the receiver shows the current signal strength and signal quality of the selected transponder Press the v button to move to the next selection item Channel Search Mode Use the oo buttons to select whether you wish to scan only free and scrambled only free or only scrambled channels To view scrambled channels you need the appropriate CA Conditional Access module and a valid smart card together with a valid subscription to the relevant Pay TV provider Press the v button to move to the next selection item Network Search Use the buttons On Off to select whether a network search should be performed If you set the network search to Off only the factory stored transponders of the satellites you previously selected will be scanned for new as yet unlisted channels If you set the network search to On the transponder network enables additional transponders that have not yet been stored to be located They are then stored and scanned for new channels in the same way as the existing transponders When you have made your settings use the Av buttons to select Start Search and press the button to start the search You can cancel the search at any time by pressing the button During the search you will see a display that shows you the progress of the search and the channels found so far Newly
21. sought see also Operating instructions Alphanumeric input Press the button to start the search Info on Press the 3 button to view additional items of information on a channel Signal Strength 4 C am 755 Press the 3 button to view the following additional items of information I Signal strength oo Signal quality Transmitting satellite ASTRA 19 2E Frequency MHz 11836 MHz Polarisation Horizontal If you press the 3 button twice instead of the signal strength and signal quality the following identification numbers IDs for the current signal are displa TSID Transponder identification number OID Network identification number Audio PID Program related service identification number ASTRA 19 2E PCRPID Identification number for the synchronisation signal 11836 MHz Video PID Identification number for video signals Horizontal Audio PID Identification number for audio signals 27 500 MS s You can hide the additional information by pressing the 3 button again The cursor buttons QJ 906 are used to navigate within the respective channel list view to select the desired channel The selection of the desired channel is confirmed by pressing the button You will now hear and view the currently selected channel in the small window at the top right To exit the channel list and return to the TV picture press the button again or press the button 37 EPG
22. these this device is only to be used by end customers for private non commercial purposes and for licensed content Use for commercial purposes is not authorised Utilisation of products or proce dures sold or used with this device are not comprehended With reference to licensed technologies applica tion of reversible procedures as well as dismantling of the device are both not permitted CONTENTS PREFACE I I I 2 IMPORTANT INFORMATION I I I I u u 3 ele Hz ERR 4 SAFETY INSTRUCTIONS IMPORTANT NOTES centres estre sette stems 6 RECEIVER FEATURES SCOPE OF SUPPLY J I 7 CONTROLS DISPLAYS AND CONNECTIONS J I 8 CONNECTION AND SET UP I I I 9 REMOTE CONTROL I I I I I U u 11 FIRST INSTALLATION I I I I U se sp ss sss sss 13 OPERATING INSTRUCTIONS I I I I u 32 MENU CONCEPT 32 33 ALPHANUMERIC INPUTS c cccececescecescececescececeecececsececeesevscecsecaceecevaceecevaceesatcessaveneavateeenvaten 34 LANGUAGE SETTING I n Ia sse aaa aa 34 KEY TO RECEIVER DISPLAY SYMBOLS I I I tret aT 34 ON SCREEN DISPLAYS OSD U
23. to the TV picture You will see information on the current or next following programmes in the EPG only if it is supplied by the channel provider If no EPG data are available the receiver instead of showing information on the current programme shows the message No data available CURRENT VIEW The Current view can be called up at any time in EPG by pressing the green button This is then automatically displayed every time the EPG is started see screenshot Calling up EPG In the Current view you see all channels displayed in the order of the overall channel list Provided that EPG data has been supplied by the channel provider the receiver shows for each channel the current programme being shown with start time finish time and progression bar You can use the cursor buttons 8000 or the keypad buttons to select the desired channel and if 39 EPG ELECTRONIC PROGRAMME GUIDE available you can use the 3 button to call up further information on the desired programme The gt button allows you to look ahead in 15 minute steps to future programmes for the channels press the button to return to the current time If you wish to view the programme currently being shown a channel you need not exit the EPG just select the desired channel and press the button At the top right of the screen you will see the current TV picture for the selected channel The picture however only appears o
24. with the specified mains voltage marked on the rear of the unit or on the external power pack The unit may only be connected to the mains and turned on once it has been connected to the antenna and to the TV set or the cable network and PC If the mains voltage is too high there is a risk of fire Repairs Ensure that any repairs to your unit are carried out by qualified personnel Opening the unit and attempting to repair it yourself voids all warranty claims Improper work on the unit can jeopardise the electrical safety of the unit The manufacturer accepts no liability for accidents caused by the user opening the unit Connections Incorrect wiring of the connections can lead to malfunctions or defects on the unit Long periods of absence storms accessibility of the mains connector Always turn off the unit at the mains switch if you will be absent for a long time or there is a storm Disconnect it from the mains by unplugging the mains connector This also applies to the other equipment connected to the unit Isolation from the cable network is also recommended Note any timer programs receiver and turn the unit on again promptly before the recording time Ensure the mains connector is accessible at all times Installation location All electronic equipment generates heat However the heating of this unit lies within the permissible range Sensitive furniture surfaces and veneers may become discoloured by the effects of constant he
25. your reception position is aligned to the desired satellite s Number of Satellites Use the GP buttons to select how many satellites max 4 you would like to receive with your reception system The following display appears example r Use the OD buttons to select the first satellite slot Press CJ to access the menu for the satellite settings The following display appears example Satellite and Position Use the o0 buttons to set the desired satellite selection from 17 pre programmed options 16 FIRST INSTALLATION DiSEqC M1 0 LNB Type Here use the oo buttons to select the LNB type used in your system The choice is between Universal and User defined Universal No further input is required since all necessary frequency ranges are covered by a universal LNB User defined If you choose not to use a universal LNB you must here set the frequency ranges for which your LNB was configured Use the Av buttons to select the frequency range to be changed low high or limit frequency Use the lt gt buttons or the digital input buttons to set the exact frequency for which your LNB was configured Test transponder To check whether the settings that you have made are correct use the Av buttons to move to the Test transponder field Use the oo buttons to select the required transponder from the various ones listed If your settings are correct you will see at the top right of
26. ELECTRONIC PROGRAMME GUIDE CALLING UP THE EPG The EPG is called up by pressing the button Each time the EPG is called up you will automatically be shown the Current view irrespective of which view you were shown the last time you exited the EPG The following display appears example Today s date Selected EPG view and time Wednesday 06 06 2007 14 59 Current picture Current on the selected Channel channel number from Das Erste lie LU Rote Rosen the overall list channel Wunderbare Welt name current 3 SAT 1 programme no data avallable with progress 4 RTL Television Day of the week and period of time in which the 01 MI 0 Fr Se ONCCNUCNICNEB ee ete EAR Bot bed cd no data available CN bar 5 RTL2 06 06 07 14 10 15 00 highlighted no data avallable Zain programme 6 is showing no data available 7 ProSieben no data available 50 Mi Timer list Later Preview Category time of the v2 1 24Hours Exit EPG Record 12 Search highlighted programme with category duration and picture format At this place you will be shown the age limitation of the highlighted programme if this is supplied by the channel provider Note If you had selected a favorites list before calling up the EPG you will see in the EPG only the data for the channels that are included in your channel list Press the b
27. Lock Channel can be viewed only by inputting a PIN Rename Favorites List The Favorites List can be renamed Start Blockselection Several channels can be selected at the same time and edited together REMOVE FROM THE FAVORITES LIST Use the Av buttons to select the channel to be removed from the Favorites List you have selected Press the button to up the edit menu and use the Gj buttons to select the Remove from Favorites List function Confirm the command by pressing the button The channel you previously selected is now removed from the Favorites List but not deleted from the overall satellite list 56 EDIT CHANNEL LIST LOCK CHANNELS Use the OD buttons to select the channel to be locked from the Favorites List you have selected Press the button to up the edit menu and use the N buttons to select the Lock function Confirm the command by pressing the button You are now prompted to enter the PIN code factory default setting 0000 The channel you previously selected is now shown with a padlock to its right In future this channel can be viewed only by inputting the four digit PIN code The channel is also locked on all other channel lists You need not additionally access the other channel lists to lock the channel This function can be restored again using the edit menu select Remove lock RENAME FAVORITES LIST Use the OS buttons to select the Favorites List to be ren
28. Operating manual englisch DVB Satellite Receiver UFS 710si 710sw KATHREINMN KATHREIN Antennen Electronic PREFACE Dear customer this operating manual is intended to help you make the fullest use of the extensive range of functions offered by your new satellite receiver We have tried to make the operating instructions as easy as possible to understand and to keep them as concise as possible To help you understand particular specialist terms that cannot be translated we have added a short glossary the end of the manual The power switch is an environmentally friendly feature If you will not be using your receiver for an extended period you should use the power switch to disconnect it from the power supply and save energy For shorter breaks you can use the remote control to switch the receiver to standby which uses only a minimal amount of energy We wish you good reception and much pleasure using your new DVB satellite receiver Your KATHREIN Team DISPOSAL INSTRUCTIONS Electronic equipment is not domestic waste in accordance with directive 2002 96 EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL dated 27 January 2003 on used electrical and electronic appliances it must be disposed of properly At the end of its service life take this unit for disposal to an appropriate official collection point Used batteries are special waste Do not throw spent batteries into your domestic waste take them t
29. PG data supplied by the channel providers in advance of the latest EPG update Use the buttons to select the recording mode Series recording In series recording the start and finish of recording are taken automatically by the receiver from the EPG data You can specify only a single value for the lead in and run on time to be sure to record the complete programme even if transmission times may vary slightly The setting of lead in and run on time is done using the buttons or the keypad When all settings have been made press the button to save the recording settings You can view the recoding schedule in the Timer List view of the EPG see item Plan recording 47 EPG ELECTRONIC PROGRAMME GUIDE PLAN RECORDING FAV The Timer List view can be called up at any time in EPG by pressing the 8 red button The timer list view shows you all the recordings that are scheduled The IO buttons allow the recordings to be sorted into once only recording or Repeating recordings The cursor buttons 851060 allow you to select recording The button allows you to switch to the channel on which the recording is scheduled The red dot button allows you to delete a recording that had been scheduled If this is a series recording you will additionally be asked whether you wish to cancel the recording of only one episode or whether you wish to record no further episodes of this series s
30. S NDS MDR FERNSEHEN Gsetectrist Select saten rv Radio Press the button to access the channel list CD ext EQ search channet into Calling this up displays the channel selection sorting list from which you selected the last channel At the top right you will see the selected channel list TV or radio channels displayed Press the 9 blue button to switch between the TV and radio channel lists 36 ON SCREEN DISPLAYS OSD To the right of it you see the current channel list sort order as selected by you The channel list can show channels sorted by various selection and sorting criteria Selection and sorting options Press the red button to call up the favorites list selection The OS buttons allow you to scroll through the existing favorites lists Press the 8 green button to return to the overall list all satellites Use the OS buttons to choose between the received satellites display all channels from a satellite and the list of New channels provided by channel search Press the 8 yellow button to see an alphabetic listing This shows all the channels sorted alphabetically or the ones beginning with the selected initial letter Use the OS buttons to make the selection Search function Press the button to start the search The numeric pad buttons allow you to input the desired search 2 11 expression for the channel that is
31. Y a uu s e E E a saa 46 RECORD USER DEFINED aan EM CERE EV S 46 SERIES RECORDING 47 PLAN RECORDING cececcccececessececsesececsececseseveceesececsasacecsasatecsecaceccevateccatateucavateecsvatessattereeees 48 COMMON INTERFACE erret th I I U u 49 IMPORTANT INFORMATION ccecccsececcecececcesececcececeesececeecececsesaceceecateccavateccavatecevatercevecereeees 49 INSERTING THE SMARTCARD AND THE CA MODULE 49 VIDEOTEXT TELETEXT I I I u u 51 EDIT CHANNEL AI MM 52 SELECTION OF THE LIST CHANNELS TO BE EDITED 52 EDITING LISTS CHANNELS eee ttt tnter tad 53 4 CONTENTS LAS TEEUNGTION MEMORN u lu sia 88 85 a ee ee 54 MOVEIOHIANNELES uuu ee era area ee en 54 DELETE ERANNELS 54 ORA NNEE e ae 54 CIH TL 55 COPY CHANNELS IO THE FAVORITES LIST esse aan ee 55 START BLOCKSELECTION SELECTING SEVERAL CHANNELS 55 EDIT FAVORITES LIGT u u a ee 56 REMOVE PRON THE FAV OR TES OS TI au anne ante ee een 56 Eat GAIN en ee ee ee 57 RENAME FAVORITES LIST aussen ea ee een 57 START BLOCKSELECTION HIGHLIGHTING SEVERAL CHANNELS
32. akula Patienten ilie das Wi Julia Wege zum Gl ck 0 heute Wetter Inhalt A Z 101 Service Wetter 170 Stau Prognose Sport 200 Der WISO Tipp Promi News 801 Spendenkonten When the search is finished the videotext Teletext being broadcast by the relevant encrypted provider appears You have several options for calling up the desired pages Input with the numeric pad Scroll through using the AYv buttons Select the options shown at the bottom end by pressing the respective coloured button red PIP OPT green yellow and m blue By pressing the button you can double the size of the displayed text Pressing the button once enlarges the upper part of the display pressing the button twice enlarges the lower part of the display pressing the button again returns the display to normal size Press the or button to exit Videotext 51 EDIT CHANNEL LIST Select the Edit TV Channellist menu using menu button the Av buttons on the main menu and Mainmenu gt Edit TV Channellist f All Satellites ZDF SAT 1 RTL Television RTL2 VOX ProSieben kabel eins Bayerisches FS S d WDR K ln Also pay attention to the bars at the bottom of the on zeanousuwn screen display These provide information on what to do next tist Aiphabeticaiy v Radio Deu cuit search 2 When the menu is called up th
33. al Access for decoding of encrypted programmes 86 TROUBLESHOOTING Inthe event of a malfunction first check all the cable connections and operating states Receiver and TV set power plugs are connected to the wall socket Antenna cables are located on the receiver input Receiver and TV set correctly interconnected by a Scart or cinch cable Receiver and TV set Hi Fi Dolby Digital system are switched on check power indicators Receiver is responding to remote control 4 2 3 4 Audio connections are made to Hi Fi or Dolby Digital system as appropriate 5 6 A selection of troubleshooting tips is offered below or bad signal warning appears on some or all channels Remote control responding no longer Wrong time being displayed The following channels cut out or Bad or no signal appears PRO 7 SAT1 Kabel 1 DSF N 24 Tele 5 9 Live HSE 24 and Sonnenklar TV Black or blue screen no on screen displays SERVICE Antenna signal of satellite reception system missing or faulty Incorrect LNB frequencies set in the Antenna Configuration menu Receiver or remote control command set may have been unintentionally changed The Summer Time setting is wrong An incorrect time was imported from the signal reception DECT telephones are operating on the same frequency as these channels Interference may occur due to inadequate level or poor shielding of cable Scar
34. all up the edit menu You have the following edit options Move Channel can be moved within the current list to another channel slot Delete Delete the channel from the current list Skip Channel will be skipped when zapping through the channels Lock Channel can be viewed only by inputting a PIN To Favorite A channel can be assigned to any Favorites List Start Blockselection Several channels can be selected at the same time and edited together As soon as you exit the menu under which you made the changes you will be asked if you N wish to save the changes Use the Av buttons to select either Yes save changes or NO discard changes Confirm your selection with the button o3 EDIT CHANNEL LIST LAST FUNCTION MEMORY The last editing action performed is saved on the button so by pressing the button for other channels you will repeat the action without having to call up the edit menu again As soon as you leave the current display this option lapses and becomes available again only after the edit menu has been called up and an action selected MOVE CHANNELS Use the Av buttons to select the channel to be moved from the current channel list use the green button to switch to the overall list use the 8 yellow button to switch to the alphabetically sorted list Press the button to up the edit menu and use the A buttons to select the Move function Confirm the comman
35. ally sets itself to the right time If Off is selected the field for manual selection of summer and winter time is displayed below Press the gt buttons to perform the setting Press the 9 green button to close First Installation and return to the picture 31 OPERATING INSTRUCTIONS MENU CONCEPT The structure of the menu concept is based on logical operating sequences The programme showing on the current selected channel always appears in the top right hand corner of the screen You will find detailed descriptions of the selected menu items in the relevant sections of the operating manual Note The selected menus sub menus and positions well as the parameters to be set are each highlighted in colour The menus are self explanatory Wednesday 06 06 2007 w l 2 JAL t T Pay attention to the bar at the bottom of the on screen display These provide information on what to do next Press 4 MENU EXIT Press the button to call up the main menu and press the N buttons to call up the sub menus Press the button to access the sub menus Press the N buttons to select items within the sub menus The settings under the various options are made either by pressing the GP buttons or by using the numeric pad You can exit the main menu and sub menus and the various options step by step by pressing the button the settings changes you made ar
36. amed Press the button to up the edit menu and use the Av buttons to select the Rename Favorites List function Confirm the command by pressing the button A keypad will now be displayed with which you can enter the desired name alphanumerically using the numeric pad on the remote control See also the section Operating instructions Alphanumeric input START BLOCKSELECTION HIGHLIGHTING SEVERAL CHANNELS Use the Av buttons to select the channel as the start point from which you want to select further channels You can only select channels that are listed in succession in your selected Favorites List Press the button to call up the edit menu and use the Av buttons to select the Start Blockselection function Use the Av buttons to select the desired channels starting from the previously selected channel and working upwards or downwards The selected channels will be highlighted in yellow and marked with a tick at the left side When you have highlighted the channels that you wish to select press the button to up the edit menu once again and use the 4 buttons to select the desired function Remove from Favorites List or Remove lock The selected function can now be used in the same way as described for the respective items in this section for a single channel 57 SEARCH CHANNELS CHANNEL SEARCH Select the Search Channels menu using the menu button the 4
37. at over time The feet of the unit can also cause colour changes to treated furniture surfaces If necessary place the unit on a suitable stable and flat base Ventilation The heat generated in this unit is adequately dissipated However the unit should never be installed in a cupboard or on shelves with inadequate ventilation Never cover the cooling slots on the unit e g with other equipment magazines tablecloths or curtains Do not place any objects on top of the unit and maintain a clearance of at least 10 cm above the unit so that the heat generated can be dissipated with no obstructions Moisture sunlight heat naked flames Protect the unit against moisture dripping and splashed water do not place any filled objects such as vases on top of the unit Do not place the unit close to a heater or expose it to direct sunlight and do not operate it in damp locations Only use the unit in a moderate climate not in tropical conditions Do not expose the unit to any naked flame such as from a candle This constitutes a fire hazard RECEIVER FEATURES SCOPE OF SUPPLY The UFS 710si and UFS 710sw receivers are suitable for receiving digital satellite TV and radio channels The built in Common Interface offers space for two CA modules for pay TV channels and ensures a guaranteed future The receiver indicates the channel name on the 16 character alphanumeric display The display also has 16 icons that provide information on specific
38. button to call up the edit menu and use the Av buttons to select the Start Blockselection function Use the Av buttons to select the desired channels starting from the previously selected channel and working upwards or downwards The selected channels will be highlighted in yellow and marked with a tick at the left side When you have highlighted the channels that you wish to select press the button to up the edit menu once again and use the Av buttons to select the desired function Move Delete Skip Lock or To Favorite The selected function can now be used in the same way as described for the respective items in this section for a single channel 55 EDIT CHANNEL LIST EDIT FAVORITES LISTS Wednesday 06 06 2007 15 23 Mainmenu gt Edit TV Channellist Fav5 Kultur f 22 arte Fass 34 EinsFestival 37 ZDFtheaterkanal Fats Signal Strength Cu 76 Signal Quality C 2 100 ASTRA 19 2E 11953 MHz horizontally 27 500 MS s DS Select List Alphabeticaiy TV Radio ext cuit 9 search FAV When you have selected the Favorites List to be edited called up using the red button and selected using the OS buttons press the red dot button to up the edit menu You have the following edit options Remove from the Favorites List The channel will be removed from the Favorites List
39. buttons on the main menu and eg Wednesday 06 06 2007 9 15 2 5 Also pay attention to the bars at the bottom of the on screen display These provide information on what to do next You have three options for a channel scan Automatic Channel Search all transponders for the satellite you selected will be scanned Manual Channel Search only the selected transponder for the satellite you selected will be scanned Search with Service ID Search for specific channel using its service ID Use the Av buttons to select the search mode you require and confirm with the button AUTOMATIC CHANNEL SEARCH Wednesday 06 06 2007 The OD buttons allow you to select different sets of parameters for the search 58 SEARCH CHANNELS CHANNEL SEARCH Satellite Select the satellite t0 be scanned using the GE buttons Make sure your reception system is aligned to the selected satellite You can scan only one satellite at a time If you have connected a multi feed reception system e g reception of ASTRA 19 2 East and HOTBIRD 13 East you must repeat this procedure once for each satellite You can however start the first installation again in the course of which a channel search of all the satellites you selected is performed Press the v button to move to the next selection item Channel Search Mode Use the oo buttons to select whether you wish to scan only free and scrambled only free or only scramble
40. by pressing the 9 blue button m This symbol indicates that an encrypted channel has been selected This symbol appears whilst the receiver is recording under a program control the signal is forwarded from the receiver via the VCR Scart socket to an external recorder 34 ON SCREEN DISPLAYS OSD CHANNEL MESSAGES TV CHANNEL MESSAGES 14 10 Wie wir alle Amis wurden 15 15 Kalimera Mr Marshall Channel information is shown for a few seconds each time the channel is changed this can be changed under Settings Adjust Displays or displayed continuously by pressing the 3 button RADIO CHANNEL MESSAGES The information for the current radio channel has the same layout PROGRAMME INFORMATION Press the 3 button twice to view information on the current programme if transmitted by the channel provider Use the Av buttons to scroll Folge 1 131 Jule w rde nichts lieber tun als sich nur um Kodjo zu k mmern der weiterhin von der Abschiebung bedroht ist Doch stattdessen muss sie den vom Gericht through the pages By pressing the buttons vernangten Sozialdienst im Traumazentrum antreten you can obtain information on the next following 5 on the current channel Press the 3 or button to exit the display CALLING UP THE OPTIONS CHANNEL If the Channel Information displays the following icon this is a Portal Channel Pressing the 8 yell
41. ch other You can find the necessary information transmission frequencies in the documentation supplied with your system Secure channel with PIN If your single cable system allows the transmission frequency to be protected by inputting a PIN this is the menu where that can be done No other receiver can then use that transmission frequency unless the PIN is input Use the buttons to select the setting Yes A line with the text Password PIN is then displayed Press the Av buttons to select this line You can now use the numeric pad to input a PIN 0 255 23 FIRST INSTALLATION Single cable system Manual Test connection When you have completed all the settings press the 4 buttons to switch to the Test connection selection field and press the button The receiver now tests whether a connection to the single cable system can be established or not As soon as the receiver has established a connection to the single cable system you will see the following display Press the 0X button to acknowledge this display Then press the button You will be asked whether I AI connection 18 you wish to save the changes Use the N buttons to select Yes save changes and confirm by pressing the button Now press the green button The receiver will automatically display the selection menu for the channel search Continue by selecting the item Execute Channel search no
42. d channels To view scrambled channels you need the appropriate CA Conditional Access module and a valid smart card together with a valid subscription to the respective Pay TV provider Press the v button to move to the next selection item Network Search Use the buttons On Off to select whether a network search should be performed If you set the network search to Off only the factory stored transponders of the satellites you previously selected will be scanned for new as yet unlisted channels If you set the network search to On the transponder network enables additional transponders that have not yet been stored to be located They are then stored and scanned for new channels in the same way as the existing transponders When you have made your settings use the OD buttons to select Start Search and press the button to start the search You can cancel the search at any time by pressing the button During the search you will see the following message example Wednesda 06 06 20 7 5 15 29 59 SEARCH CHANNELS CHANNEL SEARCH Newly found channels are identified with the designation new after the channel name After completion of the search you will see the following message example Wednesday 06 06 2007 15 43 Mainmenu gt Search Channels 2 Automatic Channel Search New TV Channels 334 New Radio Channels 179 Press the button You will be asked whether yo
43. d by pressing the button The channel you previously selected will now be shown inset slightly from the left Now use the cursor buttons 0000 or the numeric keypad to select the new desired position for the channel and confirm the new channel slot by pressing the button DELETE CHANNELS Use the OD buttons to select the channel to be deleted from the current channel list Press the button to call up the edit menu and use the OD buttons to select the Delete function Confirm the command by pressing the button A deleted channel can be recovered only by performing another channel search see section Channel Search The channel you previously selected will be deleted from the Favorites Lists also SKIP CHANNELS Use the OD buttons to select the channel to be skipped from the current channel list Press the button to call up the edit menu and use the Av buttons to select the Skip function Confirm the command by pressing the button The channel you previously selected is now shown in grey text When zapping the channels this channel will in future be skipped and no longer shown in the channel list called up using the button This function can be restored again using the edit menu select Restore to zap list 54 EDIT CHANNEL LIST LOCK CHANNELS Use the Av buttons to select the channel to be locked in the current channel list Press the button to call up the edit menu and use the A
44. de press the button to save the recording settings You can view the recording in the Timer List view of the EPG see item Plan recording 45 EPG ELECTRONIC PROGRAMME GUIDE RECORD WEEKLY Remember that the day of the week for the desired programme is loaded in the recording schedule and you can make no further manual corrections to it Therefore before pressing the red dot button select the programme on the day of the week that in future you will wish to make the weekly recording Use the gt buttons to select the recording mode weekly see screenshot below Use the Av buttons to switch to the selection field Start and use the buttons or the numeric pad to select the desired recording starting time Use the Av buttons to switch to the selection field End and use the buttons or the numeric pad to select the desired recording ending time TV Program Guide f Mon 10 00 Das Erste a i X 10 00 10 03 10 08 qe Recording mode 3 Plan recording A When all settings have been made press the button to save the recording settings You can view the recording in the Timer List view of the EPG see item Plan recording RECORD USER DEFINED Use the J buttons to select the recording mode user defined see screenshot on next page Use the 4 buttons to switch to the selection field Day
45. deo resolution CCIR 601 720 x 576 lines Input data rate MSymb s 2 45 Video decoding MPEG 1 and 2 compatible Bit rate MBit s 1 5 15 Frequency range MHz 0 02 5 Output voltage Vss 1 S N dB 558 TV system audio Audio decoding MPEG 1 and 2 layer 1 and 2 Sampling rate kHz 32 44 1 48 Frequency range kHz 0 04 20 Output voltage mVss Type 770 S N dB gt 65 Memory Flash RAM DDR RAM MB 4 16 Processor clock speed MHz 200 Power Supply Power supply voltage VAC Hz 230 15 50 Power consumption power standby W lt 26 lt 3 5 LNB supply vert horiz V mA 14 18 Max 400 Control signal kHz 22 DISEqC M1 0 SCR single cable system Connections Sat IF input output loop through 2 x F sockets TV VCR output 2 x Scart sockets Video output Cinch socket Audio output analogue 2 x Cinch sockets Audio digital output electrical optical Cinch socket Standard fibre optic Data interface RJ 11 socket Common Interface 2 General Permissible ambient temperature 5 to 40 Unit dimensions weight mm kg 280 x 49 x 190 lt 2 11 TECHNICAL APPENDIX SCART SOCKET ASSIGNMENT Signal TV VCR AUX Right audio output 1 X X Right audio input 2 X Left audio output 3 X X Audio earth 4 X X Blue earth 5 X X Audio left input 6 X Blue signal 7 X X Switching voltage 8 X X Green earth 9 X X Data signal 10 Green signal 11 X X Data signal 12 Red earth 13 X X Data earth 14 Red signal C 19 X X Blanking signal 16 X
46. e saved Press the button to return directly from one of the menus to the TV picture the settings changes you made are saved 32 OPERATING INSTRUCTIONS MENU TREE Main Menu Call up the Main Menu by pressing the button Mainmenu Mainmenu Das Erste 5 1 RTL Television RTL2 VOX ProSieben kabel eins Bayerisches FS S d WDR K ln Selact List oOo Select Stel Alphabetically TV Radio Peach naw channalz on satellite Exit Edit tor Search Co Exit mainmenu Back 4 Swen ow pb u nfe Mamana 2 Parental Control First Installation Prat lt gt to lock untock tha malnmanu Press execute the First Installation mainmenu Ct mainmenu Ce r Mainmenu Mainmenu Service Menu Das Erste EN T un English Software version V2 12 WI Fran ais Hardware version V2 0 Italiano Date of the channel list 24 06 2008 Espanol Cestina Nederlands Date of last update 14 11 2008 3 Turkce Press 7 to update the software and or the chasnellist Exit mainmenu back Coco Exit mainmenu 33 OPERATING INSTRUCTIONS ALPHANUMERIC INPUTS Use the displayed keypad see figure to the right for entry of favorites names or search expressions by s
47. e standard setting is for the receiver to show the All Satellites channel list with all channels available on the satellites that are being received SELECTION OF THE LIST CHANNELS TO BE EDITED Press the 9 blue button to switch between the TV and radio channel lists Radio channels are edited in the same way as TV channels Editing Favorites Lists is explained as a separate item Selection options TR blue button Switch between radio and TV channels green button Call up satellite channel lists 2 yellow button Call up the channel lists sorted alphabetically button Search for a specific channel input the search expression using the Numeric pad on the remote control see also section Operating instructions Alphanumeric input The channel list chosen is generally sorted by categories satellites favorites and alphabetic using the OS buttons the standard list shown on calling up is the All Satellites channel list Selection of channels in the list is performed using the cursor buttons MMA The Av buttons allow you to select individual channels and the buttons allow you to scroll from page to page of the currently selected list 52 EDIT CHANNEL LIST EDITING LISTS CHANNELS Wednesday 06 06 2007 EST All Satellites When you have selected the channel or channel list to be edited press the red dot button to c
48. e the First Installation Exit mainmenu Back Press to access the TV Video and Audio menu The following display appears see next page Use the Av buttons to select further options If there is another sub menu layer press the button to open it If there are no more sub menus make the settings using the Gea or numeric pad Press the button to save your settings and return to the previous menu Press the button to return directly to the TV picture the changes will also be saved 66 TV ASPECT RATIO Here you can use the buttons to select the format for your Either 4 3 16 9 format PICTURE FORMAT Here press the J gt buttons to select the screen display mode e Pan Scan Letter Box e Automatic only if the 16 9 TV format was selected e Always 16 9 only if the 16 9 TV format was selected TV SCART OUTPUT Here you can use the oo buttons to select the type of video signal at the TV Scart socket Select the signal that your TV set can process When doing this refer to the operating instructions for your TV set e CVBS Composite colour baseband signal colour picture blanking synchronization signal e RGB Red Green Blue signal or e Y C S Video signal luminance chrominance 67 VCR SCART OUTPUT Here you can use the oo buttons to select the type of video signal at the VCR Scart socket Select the signal that your external recorder can proc
49. ect the Service menu using the menu button the N buttons on the main menu and The following display appears f MEE Eee Mainmenu gt Service Menu ERBE IN Current software version Hardware version V2 12 V2 0 24 06 2008 Software version Hardware version Date of the channel list Channel list status Date OT last update 14 11 2005 Press 23 to update the software and or the channellist C Exit mainmenu CI Back 4 Last update run UPDATE SOFTWARE The receiver checks in standby mode whether a new software version is available and if it is displays the following message the next time the receiver is started up GENERE J Use the OD buttons to select from the displayed options and press to confirm your selection e Load in standby When the receiver is switched to standby mode the new software is loaded Remind later The message reappears the next time the receiver is started up e Don t load The software is not loaded and the download must be launched manually To load the software manually Use the Av buttons to switch to Software Update and then press The following display appears next page 71 SERVICE MENU New software available 2 12212 Date of the channel list 04 07 2008 The existing order will remain unaffected Also pay attention to the bars at the bottom of the on screen display The
50. ee screenshot Selection is performed using the A buttons and is confirmed using the button Y tert 4 FERE Discontinue daily recording Ne Ln The 5 button allows you to skip backwards and forwards through the future timer lists a day at a time 48 COMMON INTERFACE IMPORTANT INFORMATION Always follow the operating instructions from your Pay TV provider and the instructions supplied with the Smartcard and the CA module Smartcards and CA modules are not included with this product The cards and modules are issued by the respective Pay TV providers and contain the subscriber data and details of the channels for which the subscriber has paid These channels are always encrypted Contact the Pay TV provider if you are interested in subscribing to a particular Pay TV channel You are responsible for the use of the Smartcard in the CA The Smartcard sold by the Pay TV provider specific to a particular encryption technology is inserted into the CA module Store your card and PIN code securely when not in use INSERTING THE SMARTCARD AND THE CA MODULE The Common Interface 3 of the UFS 710 is suitable for the use of two CA Conditional Access modules These two Cl slots are on the front right behind the display The CA module 2 accepts the SmartCard chip contacts pointing upwards and towards socket strip and is then inserted into one of the two Cl slot
51. elect whether the main menu should be locked If the menu is locked changes can be made only by entering the four digit PIN code Use the oo buttons On Off to select whether the receiver should be locked If the receiver is locked it can be operated only by entering the four digit PIN code after it is switched on factory setting 0000 Press the button to exit the menu PARENTAL CONTROL DEFINE NEW PIN CODE Press the button to replace the old with new one Enter the new four digit PIN For security you must repeat the new PIN code once again Confirm the change of PIN code by pressing the button Keep your password in a safe place so that you always have access to your channels even if you might have forgotten it If you have forgotten your password you must contact your dealer who will be able to unlock your receiver for you 65 SETTINGS The selected menus sub menus and positions as well as the parameters to be set are each highlighted in colour The menus are to a large extent self explanatory Wednesday 06 06 2007 15 48 Mainmenu 3 Settings Pay attention to the bar at the bottom of the on screen display These provide information on what to do next 1 2 Select the Settings menu using the menu button the 4 buttons on the main menu and gt armenu Settings 20 Das Erste h First Installation Press 2 to execut
52. electing numerals for the desired letters digits You can choose between upper or lower case letters button Use the numeric pad to select the desired character About two seconds after selection of the character the cursor moves automatically to the next position The button allows you to delete your entry character by character When you have selected all the characters press the button to save your entry and start a scan to find the desired expression LANGUAGE SETTING OSD The language for the on screen display is set as follows gt Av Language Setting gt Av English gt Available options German English Italian French Dutch Spanish Czech and Turkish After you have performed the settings press the or the button to exit the Main Menu You will then return to the TV picture KEY TO RECEIVER DISPLAY SYMBOLS Various symbols are occasionally shown in the receiver display above the normal display channel name These are not shown permanently they are shown only for specific functions procedures or channel features This symbol indicates that a Dolby Digital soundtrack is available on the currently selected channel call up by pressing the 8 yellow button and select by pressing the Av buttons This symbol appears after pressing the button mute and disappears when the button is pressed again sound on This symbol indicates that you are receiving in radio mode call up
53. em Recording 41 EPG ELECTRONIC PROGRAMME GUIDE SEARCH FUNCTION The search function can be called up at any time in EPG by pressing the button Wednesday 06 06 2007 ae TV Program Guide Current The search function allows you to search for programmes based on their additional information or their name Use the keypad to input the desired search expression see also Operating Instructions Alphanumeric Input When you have input the desired search expression press the button to start the search You can use the cursor buttons APGE to select the desired programme and if available you can use the 3 button to call up further information on the desired programme Wednesday 06 06 2007 15 05 TV Program Guide Search Urlaub Mil A mm il 7 m un IET I I Using the red dot button you can load the selected programme into the recording settings see item Recording 42 EPG ELECTRONIC PROGRAMME GUIDE ADDITIONAL INFORMATION i BUTTON The additional information can always be called up by pressing the 3 button whenever the i symbol appears in front of the 1 program name see screenshot on the right First however the channel must be selected The following display appears example Wednesday 06 06 2007 15 06 po Guide Wed 06 06 07 Isat 17 15 17 46 Bilder aus Deutschland
54. erating manual is a registered trade mark of the European Telecommunication Satellite Organisation EUTELSAT SWITCHING OFF THE RECEIVER AND UPDATING THE EPG By pressing the 5 button you can switch the receiver out of mode and into standby mode Pressing any of the numeric buttons returns it from standby mode into operating mode Every night at 03 00 the receiver automatically starts to update the EPG data This updates the EPG data for the first 25 channels of the overall channel list This update happens however only if the receiver is in standby mode If the receiver is completely switched off the mains or if it is in operation the update will be delayed The receiver will update the EPG data when it is next switched from operating mode into standby mode After updating the data the receiver automatically switches back to standby You can however by pressing the button break off the update before it is finished the receiver then switches immediately into standby mode REFERENCE NOTE ON AUDIO MPEG INC AND S 1 SV EL S P A This device employs legally protected technologies which are protected by patents in the USA as well as by intangible property laws in other countries Audio MPEG Inc and Societa Italiana per lo sviluppo dell elettronica S 1 SV EL S P A have granted KATHREIN Werke KG rights of use which are subject to certain restrictions These restrictions must also be observed by you as a customer According to
55. ere to select the settings for your TV set When doing this refer to the operating instructions for your TV set TV aspect ratio Here you select the TV format Either 4 3 or 16 9 14 FIRST INSTALLATION General Picture format Here you select the type of screen display depending on the setting of your TV format TV format 4 3 Pan amp Scan or Letterbox TV format 16 9 Always 16 9 or automatic TV SCART Output Select the type of video signal at the TV Scart socket here Select the signal that your TV set can process CVBS Colour Video Baseband Signal Red Green Blue signal Y C S Video signal luminance chrominance Press the O green button to move to the next menu The following display appears System Select the setting here to match your reception system using the GP buttons You have the following options DiSEqC M1 0 One Cable Simple LNB If your reception system is DiSEqC capable at System select DiSEqC M1 0 allows switch over from receiving one satellite to receiving another one If your reception system is not DISEqC capable select the setting Simple LNB If your receiver is connected to a single cable system select One Cable Press the v button to move to the next menu item Continue with the relevant section of First Installation 15 FIRST INSTALLATION DiSEqC 1 0 When selecting the satellite s make sure that
56. ess When doing this refer to the operating instructions for your recorder e CVBS Composite colour baseband signal colour picture blanking synchronization signal e Y C S Video signal luminance chrominance TELEVISION SYSTEM Here you can use the oo buttons to specify whether your TV is a e e NTSC set AUTO DOLBY DIGITAL OUTPUT Here you can use the buttons to select whether the receiver should automatically output the Dolby Digital signal if this is transmitted 68 SETTINGS FUNCTIONAL RANGE Here you can configure the functional range of your receiver You can choose between Complete Simple and Medium The following table shows which functions are available at each configuration step FAV OPT TVR red button yellow button blue button Complete Select favorites Select options TV Radio AV changeover Channel List Not assigned Not assigned Not assigned Not assigned Programme Guide Select favorites Select options TV Radio Not assigned Programme Guide CHANNEL OSD DURATION Use the buttons to select the time after which you want the on screen channel notification display to be automatically cancelled The options available are Off 1 2 3 4 5 or 6 seconds DISPLAY VOLUME BAR Use the buttons On Off to specify whether the volume bar is displayed when adjusting the volume FRONT DISPLAY BRIGHTNESS Use the
57. ess module and a valid smart card together with a valid subscription to a Pay TV provider Press the v button to move to the next selection item Network Search If you set the network search to Off only the factory stored transponders of the satellites you previously selected will be scanned for new and as yet unlisted channels If you set the network search to On the transponder network enables additional transponders that have not yet been stored to be located They are then stored and scanned for new channels in the same way as the existing transponders PIP Press the green button to start channel search or if you set the channel search to No you are guided straight to the next item in the First Installation process When the search has been completed you will see the following message example 30 New TV Channels 711 New Radio Channels 108 Use the button to move to the next step of the First Installation The following display appears Local time offset 1 Hour 09 02 2009 081581 Wintertime ee Local time offset Use the buttons to set the time zone variation from UTC formerly GMT e g for Germany 1 hour Use the Av buttons to switch to the Automatic clock change field Use the oo buttons to select whether the receiver should automatically change over to and from summer and winter time If On is selected the receiver automatic
58. he exact frequency for which your LNB was configured Test transponder To check whether the settings that you have made are correct use the AYv buttons to move to the Test transponder field Use the buttons to select the required transponder from the various ones listed If your settings are correct you will see at the top right of the screen the live signal of a channel for the currently selected transponder If you are not receiving a signal check your settings again and if necessary call for expert help When you have finished configuring the satellite press the green button The receiver then automatically calls up the selection menu for the channel search Continue by selecting the item Execute Channel search 19 FIRST INSTALLATION Single cable system Use the lt J gt buttons here to select One Cable as the System Press the Y button to move to the next menu item The following display appears n Antenna Configuration The various options for a single cable system with Kathrein components are summarised at the end of this manual in the Technical Appendix section under Examples of single cable systems Press m select the connected antenna system cance Broreara to the next step 4 Number of Satellites Use the buttons to select how many satellites max 2 you would like to receive with your receptio
59. he message Check your settings and if necessary call for expert help 26 FIRST INSTALLATION Single cable system Manual Selection EXU 908 When the 908 single cable N matrix is being used it is essential that the LNB is set to Universal Transmission channel Use the buttons to select a free available transmission channel A maximum of eight transmission channels are available 1284 1400 1516 1632 1748 1864 1980 and 2096 MHz Secure channel with PIN The 908 single cable matrix allows the transmission frequency to be protected by inputting a PIN No other receiver can then use that transmission frequency unless the PIN is input Use the buttons to select the setting Yes A line with the text Password PIN is then displayed Press the Av buttons to select this line You can now use the numeric pad to input a PIN 0 255 Test connection When you have set a free transmission channel press the buttons to switch to the Test connection selection field and press the button The receiver now tests whether a connection to the single cable system can be established or not As soon as the receiver has established a connection to the single cable system you will see the following display Press the button to acknowledge this display Then press the button You will be asked whether Connection is you wish to save the changes Use the 2
60. ically display the selection menu for the channel search Continue by selecting the item Execute Channel search If no connection to the single cable system could be established you will receive the message Check your settings and if necessary call for expert help 29 FIRST INSTALLATION Channel search rwr 2 Channel Search Execute Channel search No Channel Search Mode scrambled 5 Preassigned in List TV Channels 397 Radio Channels 191 Press 4 S to enable or disable the Channel search Cancel g Forward to the next step Execute Channel search Use the GP buttons to select yes or no whether you wish to start a channel search It is not essential to start a channel seach instead you can use the factory pre programmed channels However the channels do change from time to time e g their frequencies change which the receiver does not automatically detect and can then be found only by performing a channel search PIP If you selected No you can press the green button to skip directly to next item of the First Installation If you selected Yes you can press the v button to progress to the next selection item Channel Search Mode Use the o0 buttons to select whether you wish to scan only free and scrambled only free or only scrambled channels To view scrambled channels you need the appropriate CA Conditional Acc
61. in the next display the available transmission channels Use the Av buttons to select the transmission channel you want and confirm the selection with the button No frequency can be used by more than one receiver The receivers would interfere with each other The receiver now reads the existing system data for your single cable system and configures itself The receiver has been successfully registered on your single cable system Confirm the display PIP with the button Now press the green button The receiver automatically displays the selection menu for the channel search Continue by selecting the item Execute Channel search zZ ZZ Antenna Configuration ase Wait Search transmission channels Ca cancel Antenna Configuration te A Select channel Please choose the transmission channel Every receiver must have his own transmission channel to avoid disturbances 1 1980 MHz D information Registration was successful no connection to the single cable system could be established you will receive the message Registration was abortive Check your settings and if necessary call for expert help 22 FIRST INSTALLATION Single cable system Manual If one or more receivers are already present on the system and an additional receiver is to be connected you must assign the new receiver a transmis
62. ion examples section provides a sample configuration Do not connect the unit to the power supply until all installation work has been properly carried out The guidance given in the First Installation section assumes that the receiver has been properly connected as per the Safety Instructions and Connection and Set Up sections First switch your TV set on and select the AV channel slot Switch on your receiver at the power switch at the front of the unit The following display appears Also pay attention to the bars at the bottom of the on screen display These provide information on what to do next Select the menu language you want using the 904 buttons Available options German English French Italian Spanish Czech Dutch and Turkish Press the green button to move to the next menu Note If you are unsure whether you chose the right option from a previous menu you can back a step at any time during the First Installation process by pressing the 8 button The following display appears 13 FIRST INSTALLATION General Use the buttons to select whether to replace the default channel list with presorted for Germany Austria Switzerland or Italy If you want to use the default channel list choose No under Restore Channellist Press the 9 green button to move to the next menu The following display appears Use the OLODO buttons h
63. l on which the desired programme is to be transmitted at a later time and press the red dot button starting and finishing times together with the recording date must be input manually The following display appears example TV Program Guide Mon 10 00 X Das Erste Remember to program your external recorder in accordance with the timer list registered in the receiver 10 00 10 03 Plan recording Target In the first line Target select External recorder using Monday 09 02 2009 the cursor buttons 09 58 4X C96 10 08 GO Recording mode CJ Pian recording Use the oo buttons to select the desired recording mode The following recording mode options are available The recording will be performed once Daily The recording will be performed daily at a time specified by you Weekly The recording will be performed once a week on the same day and at the same time User defined The recording will be performed on days specified by you at times specified by you Series recording The selected programme will be set up by the EPG for recording every time it is transmitted may even be on different channels This function does however requires a daily update of the EPG data the data are updated automatically when switching off into stand by mode Use the cursor buttons A Y C9 to select the further items and use the keypad to complete the settings
64. lby Digital AC 3 audio 4 Ejection button for CA modules 3 LNB loop through input 4 Audio outputs L R cinch sockets In addition there are three further 5 Video output composite colour buttons on the front of the display 6 Electrical data stream output SPDIF TV R button for switching between Sony Philips Digital Interface Format TV and radio mode for Dolby Digital AC 3 audio Channel select buttons V A 7 Scart socket for TV connection 8 Scart socket for VCR AUX connection 9 RJ 11 data interface 10 Mains power cable CA modules and Pay TV cards Smartcards are not included CONNECTION AND SET UP The following section is intended specifically for specialist dealers You only need read this section if you are performing the installation yourself The Connection Examples section provides a sample configuration Do not connect the unit to the mains until all installation work has been properly carried out Refer to the information in the Safety Instructions section CONNECTING THE UNIT SAT IF CONNECTIONS Connect the Sat IF input on the receiver to the satellite reception system Use a coaxial cable with a standard F connector If the standard connectors are not yet fitted on the cable strip the insulation from the cable as shown in the following illustration and carefully twist the F standard connectors on to the ends of the cables until they are securely seated P XXX RR EIN a Q XA
65. n system Press the v button to move to the next menu item Configure satellites Press the button to call up the menu The following display appears F 2 Antenna Conf guration gt satellite 1 of 2 Signal Strength Cu LNE High Freauene 10600 MHz Signal Quality GG u r 1 al FE d CNE SAREH Precise 1 1700 MHz Press m to select satellite for reception Satellite and Position exit mainmenu mor Use the buttons to select the first satellite satellite 1 of 2 depending the setting as shown on the screen LNB Type Here use the buttons to select the LNB type used in your system The choice is between Universal Wideband and User defined If in your reception system you use a single cable LNB e g UAS 481 from Kathrein please select here the setting Wideband If you use a single cable matrix EXU 908 or a single cable switching matrix EXR 501 551 552 1581 or 2581 from Kathrein the LNB you use must be a Universal LNB 20 FIRST INSTALLATION Single cable system Universal No further input is required since all necessary frequency ranges are covered by a universal LNB Wideband No further input is necessary since all frequency ranges are set by the Wideband LNB User defined If you are not using a Universal Wideband system you must set the frequencies here You can find the
66. n next page New software available VV 2 12212 Date of the channel list 04 07 2008 The existing order will remain unaffected RESTORE FACTORY DEFAULT SETTINGS Select the Service menu using the menu button the 4 buttons on the main menu and Use the Av buttons to switch to Restore factory default settings and to call them up press the button The following display appears F OU Das Erste All settings will be restored Channellist will remain unaffected fc I 1 iE Press the button to load the factory default settings The channels and favorites lists remain unchanged 73 CONNECTING UP THE VIDEO PVR For details of how to connect your external recorder to the receiver refer to the connection diagram provided at the end of this manual and the instructions for the external recorder RECORDING In order to make a PVR recording Record the satellite receiver must be switched on or the timers must be pre programmed see EPG Recording timer section PLAYBACK For VCR PVR playback you must have previously set the UFS 710 Scart socket to VCR mode Scart changeover using the 0 button so that the signal path is set up from the VCR or PVR AUX Scart socket to the TV Scart socket In this setting the picture from the external recorder is switched through to the TV set during playback Pressing the 0 button again a second time
67. nce EPG with timer programming m Suitable for software download satellite and PC m 8 favourite channel lists for TV and 8 for radio m Automatic date and time generation via DVB data stream m On screen display OSD in 8 languages D GB F I E CZ NL TR m 1 000 timers series and interval timers m Language selection for multilingual broadcasts 1 CA modules and Smartcards not included in the delivery scope 2 Display of information only if broadcast by the programme provider 76 Optical and electrical audio output for Dolby Digital data stream AC 3 Composite colour Y C and RGB signal output programmable via the Scart socket Cinch sockets for AV signal Videotext decoder with 800 page memory capacity Automatic 4 3 and 16 9 format recognition choice of viewing format Channel search Programme position sort function DISEqC 1 0 SCR single cable system control signals Infrared remote control with command set switching Power switch An additional IR sensor can be connected TECHNICAL APPENDIX Type 5 710si UFS 710sw Order no colour 20210109 silver 20210110 black RF properties Input frequency range MHz 950 2150 Input level range dBuV 44 83 Reception threshold EB NO dB lt 4 5 system video Modulation FEC demultiplexer DVB S standard Vi
68. nce the button has been pressed Previously what you saw was the picture of the old channel that had previously been selected even though the EPG was no longer set to that channel PREVIEW VIEW PROGRAMME LISTINGS OPT The Preview view TV Program Guide can be called up at any time in EPG by pressing the O yellow W ay 06 06 200 5 01 Wednesday 06 00 2007 Sturm der Liebe 16 00 Tagesschau 16 10 Nashorn Zebra amp Co 17 00 Tagesschau um f nf 17 15 Brisant 17 47 Tagesschau 47 55 Verbotene Liebe 00 06 07 18 90 19710 18 20 Marienhof Current affairs 18 50 AUF NACH AFRIKA Tiere Wi Das Quiz mit J rg Pilawa Also pay attention to the bars at the bottom of the on Das Wetter im Ersten iimer list curent Channel 5 1 24 Hours Exit EPG screen display These provide information on what to do next button In the Preview view you will see all the programmes that will be shown in the previous Current list of selected channels Provided that EPG data has been supplied by the channel provider the receiver shows the programmes that will be shown on the selected channel for several days in advance You can use the cursor buttons MWAH to select the desired programme and if available you can use the 3 button to call up further information on the desired programme You can use the OS buttons to scroll through the channels in the
69. necessary information in the documentation supplied with your system Use the OD buttons to select the frequency range to be changed low high or limit frequency Use the buttons or the digital input buttons to set the exact frequency for which your LNB was configured When you have completed all settings for the currently selected satellite press the button If you have selected more than one satellite repeat the previous Satellite and Position and LNB Type processes for the number of satellites you selected When you have completed the settings for all the satellites the following display appears F par Bro Use the v button to select the next menu item New registration and press the button The following display appears Use the Av buttons to select the type of installation you want and confirm with the button For clarity we have split further details into two sections Firstly we give details of Automatic installation then details of Manual installation 21 FIRST INSTALLATION Single cable system Automatic If one or more receivers are already present on the system and additional receiver is to be connected when assigning the transmission frequency the new receiver make sure that no transmission frequencies are duplicated No frequency can be used by more than one receiver The receiver searches for the transmission channels on your single cable system and shows
70. nerated directly by the module Information for Conax SECA Viaccess and CryptoWorks users Note that with monthly activation intervals the programme providers have different procedures for activating pay TV cards Activation may therefore be a few days before or after the beginning of a new month During this activation period the CA module and card must be in the slot and the receiver must be turned on a set to the booked Pay TV channel Follow the instructions from the Pay TV provider If your Pay TV card is then still not enabled we recommend you briefly withdraw the CA module with the card out of the slot with the receiver switched on and then re insert it This information has nothing to do with the properties of the unit it is merely intended to assist you The various items can be selected using the Av buttons and called up using the button Press the button to exit the menu 50 VIDEOTEXT TELETEXT This symbol in the channel notification shows you whether Videotext Teletext is available for the selected channel When you press the button the receiver processes the broadcast Videotext Teletext service for your TV set to display even when the signal is encrypted During the search the page which is being searched for is displayed in the top left hand corner with the time and date displayed at the top right DF text Urteil Fluggastdaten sind tabu Java M ngel bei Erdbeben Hilfe Hoffnung f r M
71. normally possible FEC FEC is the abbreviation for Forward Error Correction The FEC error rate corresponds to the Viterbi rate 84 SHORT TECHNICAL GUIDE PID The PID Packet IDentification number is an identification number for video signals and audio signals in the digital data stream of DVB MPEG 2 signals The receiver uses the PID number to create a unique assignment for the video and audio data transmission The PCR PID is the identification number for the synchronization signal The PID PCR is normally identical to the video PID For programmes broadcast in multiple languages the audio PD can be entered manually to assign a different language to the TV programme After the PID is entered the digital receiver automatically selects the audio data identified by the PID number from the data stream and assigns it to the video signal SYMBOL RATE The symbol rate describes the quantity of data that is transmitted per second The symbol rate is measured in MSymbols s and is equal to the number of symbols received per second TRANSPONDER A transponder is a frequency converter which receives TV and radio signals broadcast from the earth converts them and then rebroadcasts them to the earth at a different frequency A satellite carries several transponders Analogue transponders transmit only one TV channel and possibly multiple radio channels on a single transmission frequency Digital transponders transmit several TV and several
72. o a collection point for old batteries lt IMPORTANT INFORMATION The channels available on the satellites and transponders are subject to continual change If changes do occur the new channels have to be set in the receiver because the factory preset programming corresponds to the status on the date of manufacture The information for these settings can be found on the Internet or in relevant magazines Your receiver was equipped in the factory with the latest software version at that time We are however constantly working on adapting the software to the wishes of our customers and to developments in technology The Software Update section provides more information on this aspect The information in this operating manual was correct at the time of going to press We reserve the right however to make changes at any time and without prior notice new software is released for your receiver and this affects the information in the operating manual e g changes to the menus and or functions if we believe it necessary we will make available a new operating manual for download under www kathrein de Please keep the original packaging in case you need to return the product at any time If the product is not properly packed the warranty claim is invalidated Make a note of the receiver s basic settings these are set during the first installation so you can restore them if necessary The term DiSEqC used in this op
73. ow button displays the channels available at this portal such as matches a specific day of play In this example three sub channels are available for selection within this portal channel Select 35 ON SCREEN DISPLAYS OSD the channels using the AYv and buttons You can also however select the sub channels of a portal channel directly using the Av buttons without having previously pressed the 8 yellow button OPTION SELECTION Press the 8 yellow button once twice for portal channels to view further soundtrack selection options if these are transmitted by the channel provider Use the Gj buttons to scroll through the available selection options Pressing the yellow button again or pressing the button exits this display again ERROR SIGNALLING No or bad signal indicates that an error has occurred in the reception system or in the receiver settings or that the transponder is not transmitting Check the Sat IF connection and the LNB configuration If you have changed settings compare them against the basic settings provided you had made note of them as suggested CHANNEL LIST TV RADIO TV Channel Wednesday 06 06 2007 14 57 Also pay attention to the bars at the bottom of the on ZDF SAT 1 RTL Television RTL2 screen display These provide information on what to do next ProSieben kabel eins Bayerisches FS WDR K ln NDR F
74. restores priority to the UFS 710 Scart Sat signal In the setting Scart TV TV mode the internal tuner of the TV set has priority and you cannot then see the signal from the receiver on the screen unless you switch the TV set to the AV channel The settings VCR mode and TV mode are shown in the display on the receiver 74 USING THE FRONT PANEL If you have misplaced your remote control or if the batteries are flat you can still operate your receiver from the front panel BACKUP OPERATION KATHREIN There are three buttons on the front of the receiver TV R button Pressing the TV R button switches the receiver from TV mode to radio mode Pressing the TV R button a second time switches the receiver from radio mode back into TV mode Y button The channel down button switches to the next channel down in the currently selected channel list button The channel up button switches to the next channel up in the currently selected channel list Because there are no numbered buttons no password PIN protected functions can be displayed 75 TECHNICAL APPENDIX FEATURES m Reception of digital TV and radio satellite programmes m 4 000 channel memory positions m 16 character alphanumeric display with status icons for indication of channel names and transmitter information m Common interface for two CA modules 1 m Kathrein Convenie
75. s 3 The Smartcard should be inserted into the CA module without excessive force This also applies to inserting the CA module into the Cl slot Do not use without excessive force and follow the instructions supplied with the Smartcard and the CA module To remove the module press the relevant eject button 2 49 COMMON INTERFACE You can find out which Conditional Access modules are in the Cl slots on the UFS 710 and which Smartcard is in which CA module from the Mainmenu under Settings and the Common Interface menu Confirmation is by pressing the button Use the N buttons to select one of the two slots in which the CA module is located Module inserted and then press the button You will then see the menu generated by the CA module The screenshots below depend on the specific module and card and so are only intended as examples Wednesday 06 06 2007 15 14 ntitlement w ww y 2 sb rt card management CE EE nn y m Ehe From this menu your card and your PIN code allow you to access various channels from your Pay TV provider CryptoWorks has been selected as an example here The details can be different for each CA module Always follow the instructions supplied by your Pay TV provider Note The module displays may be shown in English even if you have selected German as the menu language because the menu is ge
76. se provide information on what to do next Update Software If new software is available but only then use the o0 buttons No Yes to select whether you wish to load the new software that is available If you are unsure whether you wish to load the new software you can initially set the reply to No If you do agree to the changes you can then proceed to download the software Channel List Select the required activity using the buttons Available options only update Your existing list will only be updated any new channels found will be added at the end of the channel list The sort sequence of your channel list remains unchanged the only change is that the channel data transmission frequency etc are updated download Your existing list will not be edited nor updated nor overwritten overwrite Your existing channel list will be completely superseded by a new list of available channels Your personal channel sorting will be lost If you select overwrite you will additionally see displayed the line pre sorted for Use the Av buttons to switch to this line and use the J buttons to select the desired pre sorting Your available options are for instance Germany and Austria 72 SERVICE MENU When you have made your settings use the Av buttons to select Start Update and press the button to start the update The following display appears see example o
77. sion frequency that is not already in use otherwise the receivers will gt Antenna Configuration interfere with each other Depending on the system to which they are connected a maximum of four or eight receivers may be connected to a single cable system a twin receiver counts as two 3 ess amp to choose the connected equipment receivers mainmenu Cyn k Connected equipment Use the oo buttons to select the type of system to which they are connected or the single cable system components fitted refer to the manuals instructions and notes for the system and the system components Available options User defined KATHREIN UAS 481 KATHREIN EXR 551 KATHREIN 552 KATHREIN EXU 908 EXR 4 subscribers EXR 8 subscribers single cable feed system max four receivers single cable switching matrix max four receivers single cable switching matrix max two receivers single cable matrix max eight receivers for future Kathrein single cable switching matrices max four receivers for future Kathrein single cable switching matrices max eight receivers ON Selection user defined Transmission channel Use the gt buttons to select a free available transmission channel Transmission frequency Use the numeric pad to input the four digit transmission frequency No frequency can be used by more than one receiver The receivers would interfere with ea
78. states of the receiver at a glance e g Dolby Digital timer In addition to providing high quality pictures and sound series 710 receivers also feature an attractive design in a modern housing Despite their small size the receivers have a comprehensive set of features such as electrical and optical audio output for Dolby Digital AC 3 a video output and Videotext with memory These receivers are available in silver or black housings PRODUCT PACKAGE UFS 71051 silver or UFS 710sw black Remote control RC 660 Scart cable 2 Batteries AAA 1 5 V Power supply cable Operating manual CONTROLS DISPLAYS AND CONNECTIONS This section provides a brief description of all the controls displays and connections VIEW OF FRONT PANEL FLAP FOLDED DOWN DVB RECEIVER VIEW OF REAR PANEL Or Ton KATHREIN NN Q i i a arr n IF INPUT IF OUTPUT AUDIO VIDEO 230V4 50Hz 959 2150MHz cb INTERFACE E max OO OO Front panel controls and displays Rear panel controls and displays 1 On Off switch with mains disconnect 1 LNB input 2 Display cover folded down 2 Optical data stream output SPDIF 3 Common Interface for two Sony Philips Digital Interface Format CA modules for Pay TV cards for Do
79. t connection to TV deactivated by accidentally pressing the 0 button Consult an antenna specialist to have it checked and repaired as necessary On Installation menu check LNB configuration for the satellite in question High L O 10 600 GHz Low L O 9 750 GHz and Limit frequency L O 11 700 MHz and change as necessary Set infrared code 1 as described in operating manual under Remote Control RC 660 check batteries Check Summer Time Enabled in the Settings Date and Time Setup menu and change as necessary Switch off receiver at mains switch from current channel e g ARD or ZDF wait 10 seconds and then switch back on Consult your antenna specialist Keep pressing the O button until the TV picture reappears on screen If despite studying this operating manual you still have questions about getting started with the unit or using it correctly or if unexpected problems occur please contact your specialist dealer 87 Internet http www kathrein de KATHREIN KATHREIN Werke KG Anton Kathrein StraBe 1 3 P O Box 100 444 83004 Rosenheim GERMANY Antennen Electronic 936 3200 D 0209 ZWT Technical data subject to change
80. the next selection item Service ID Using the GE buttons or the numeric keypad enter here the service ID of the channel being sought When you have made your settings use the Av buttons to select Start Search and press the button to start the search You can cancel the search at any time by pressing the button During the search you will see a display that shows you the progress of the search After completion of the search you will see the following message example Press the button You will be asked whether you wish to save the changes or not Selection is performed using the Av buttons and is confirmed using the button If you select Yes save changes the newly found channels will be added to the end of the channel list Then press the button to exit the menu The channel list is called up on to the TV screen by pressing the button see also section On screen displays Channel list TV Radio 63 Select the Parental control menu using the menu button the 4 buttons on the main menu and You now prompted to enter the code factory default setting 0000 After entering the PIN using the numeric keypad you are shown the following display rm Also pay attention to the bars at the bottom of the on screen display These provide information on what to do next Select the parameters to be changed using the N buttons Use the oo buttons On Off to s
81. the screen the live signal of a channel for the currently selected transponder If you are not receiving a signal check your settings again and if necessary call for expert help You have now completed all settings for the first satellite Press the button to return to the Satellite Selection Menu and perform the settings in the same way for the remaining satellites When you have finished configuring the satellite press the green button The receiver then automatically calls up the selection menu for the channel search Continue by selecting the item Execute Channel search 17 FIRST INSTALLATION SIMPLE LNB Satellite and position Use the buttons to select the desired satellite whose signal is to be received by the tuner When you have selected your desired satellite use the Av buttons to switch to the selection of the LNB Type LNB Type Here use the oo buttons to select the LNB type used in your system The choice is between Universal and User defined Universal No further input is required since all necessary frequency ranges are covered by a universal LNB 18 FIRST INSTALLATION SIMPLE LNB User defined If you choose not to use a universal LNB you must here set the frequency ranges for which your LNB was configured Use the Av buttons to select the frequency range to be changed low high or limit frequency Use the buttons or the digital input buttons to set t
82. ton Now press the green button The receiver will automatically display the selection menu for the channel search Continue by selecting the item Execute Channel search If no connection to the single cable system could be established you will receive the message Check your settings and if necessary call for expert help 28 FIRST INSTALLATION Single cable system Manual Selection 8 subscriber When the 8 subscriber single cable switching matrix is being used it is essential that the LNB is set to Universal Transmission channel Use the buttons to select a free available transmission channel A maximum of eight transmission channels are available 1284 1400 1516 1632 1748 1864 1980 and 2096 MHz Test connection When you have set a free transmission channel press the a buttons to switch to the Test Connection selection field and press the button The receiver now tests whether a connection to the single cable system can be established or not As soon as the receiver has established a connection to the single cable system you will see the following display Press the button to acknowledge this display Then press the button You will be asked whether konn ction i you wish to save the changes Use the AYv buttons to select Yes save changes and confirm by pressing the button Now press the green button The receiver will automat
83. u wish to save the changes or not Selection is performed using the OD buttons and is confirmed using the button If you select Yes save changes the newly found channels will be added to the end of the channel list Then press the button to exit the menu The channel list is called up on to the TV screen by pressing the button see also section On screen displays Channel list TV Radio After a scan of whatever type the receiver shows all newly found channels in the channel list under the rubric New Channels You will find this rubric in the Channel List at the end of the green satellite channel lists selection using the buttons MANUAL CHANNEL SEARCH r Wednesday 06 06 2007 15 44 Mainmenu gt Search Channels 2 Manual Channel Search Polarisation Horizontal Signal Quality 100 pr Back g 60 SEARCH CHANNELS CHANNEL SEARCH The Av buttons allow you to select different sets of parameters for the scan Satellite Use the GP buttons to select the satellite on which the transponder you wish to scan is located Make sure your reception system is aligned to the selected satellite You can scan only one transponder at a time If you wish to scan several transponders on a satellite you should start an automatic scan of the transmitting satellite Press the v button to move to the next selection item Transponder Frequency Select the transponder to be
84. utton a second time to view the EPG for all channels 38 EPG ELECTRONIC PROGRAMME GUIDE Selection options red button Calls up the plan recording display of all pre programmed recordings i gt button Jump the Current view forwards by 15 minutes 8 yellow button Call up a preview of the currently highlighted channel 9 blue button Call up the category selection sorting the programmes by categories such as movies sport series button P jump forwards 24 hours in the EPG P jump backwards 24 hours in the EPG e g into Current and into Preview button Selects the currently highlighted channel in all views Pressing the button or the button again closes the EPG and the selected channel is shown again on the TV screen red dot button Adds programme to the recording settings button Search for a particular programme or programme content input the search expression using the numeric pad on the remote control see also the section 11 Operating instructions Alphanumeric input 3 button If present shows further information on the selected programme Navigation within each view is always performed using the cursor buttons MME The Av buttons allow you to select individual channels programmes and the GP buttons allow you to scroll from page to page of the currently selected list Pressing the button or the button exits the EPG again and returns
85. v buttons to select the Lock function Confirm the command by pressing the button You are now prompted to enter the PIN code factory default setting 0000 The channel you previously selected is now shown with a padlock to its right In future this channel can be viewed only by inputting the four digit PIN code This function can be restored again using the edit menu select Remove lock COPY CHANNELS TO THE FAVORITES LIST Use the Av buttons to select the channel to be copied from the current channel list Press the button to call up the edit menu and use the 4 buttons to select the To favorite function Use the GQ buttons to select the Favorites List into which the channel is to be copied The channel remains in the satellite channels list Confirm the command by pressing the button The channel you previously selected is now shown with an and a yellow field in the channels list The F shows that it is a favorite channel the black dot in the yellow field shows in which of the eight Favorites Lists the channel can be found See the item Editing Favorites Lists for information on how to delete a channel from a Favorites List START BLOCKSELECTION SELECTING SEVERAL CHANNELS Use the Av buttons to select the channel as the start point from which you want to select further channels You can only select channels that are listed in succession in your selected channel list Press the

Kathrein UFS 710si User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents