JVC RD-T5RBU User's Manual
Contents
1. ness of the display s backlighting When the Unit is turned on Each time you press the SNOOZE DIMMER button on the Unit the backlight fully turns on or dims When the Unit is turned off Standby Each time you press the SNOOZE DIMMER button on the Unit the backlight dims or turns off When the Unit is operated on batteries you can turn on or off the backlighting of the display When the Unit is turned on Each time you press the SNOOZE DIMMER button on the Unit the backlight turns on or off Using Batteries Power Batteries 6 pcs You can operate the System on batteries When the batteries are exhausted NO BATT will appear on the display In this case re place with the new batteries Memory Backup Batteries 3 pcs Your settings such as the preset stations clock and timer are backed up with this batteries CAUTION If memory backup batteries are exhausted or not installed and the AC power cord is disconnected or there is a power failure the settings you have made will be erased from memory in approx half a day Using the Tuner l os STANDBY ON Number keys CLOCK TUNER BAND ml RD T7RGN Only You can listen to FM and AM MW stations Stations can be tuned in manually automatically or from preset memory storage One Touch Radio AC power only Just press the TUNER BAND button to turn on the Unit and start playing the station you were last tuned2. conventional record cleaner spray thinner ben zine etc to clean a CD Moisture Condensation Moisture may condense on the lens inside the Unit in the following cases e After turning on heating in the room e Inadamp room e Ifthe Unit is brought directly from a cold to a warm place Should this occur the Unit may malfunction If this happens leave it turned on for a few hours until the moisture evaporates unplug the AC power cord and then plug it in again General Notes To ensure top performance keep your CDs and the mechanism clean e Store CDs in their cases and keep them in cabinets or on shelves e Keep the CD cover closed when not in use 12 Troubleshooting e If you have a problem with your System check this list for a possible solution before calling for service e If you cannot solve the problem from the hints given here or the System has been physically damaged call a qualified person such as your dealer for service Symptom Possible Cause Action No sound is heard e The power cord is disconnected e Connect it firmly e The batteries in the Unit have lost e Replace the batteries their charge e Headphones are connected e Disconnect the headphones position Poor FM reception The FM antenna is not properly posi Extend the FM antenna and turn it to the tioned best reception position The CD skips The CD is dirty or scratched Clean or replace the CD The CD does not play The CD is u
3. THE SYSTEM eo H m e BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN GOING OUT OR WHEN THE SYSTEM IS NOT IN USE FOR AN EXTEND ED PERIOD OF TIME Plug the AC power cord into the wall outlet and your System is at your command Common Operations Display ss DA CLOCK DISPLAY STANDBY indicator O L snoozeoimmer __ BASS TREBLE Ga AHB PRO OS I J VOLUME ES SNOOZE DIMMER senor MG RD T7RGN B SNOOZE RD T5RBU RD T7RGN Only Turning the Power On and Standby Turning the Unit On Press the button I STANDBY ON O I mn or STANDBY The STANDBY indicator goes out and the display comes on and WELCOME is displayed The Unit comes on ready to continue in the mode it was in when the power was last turned off E For example if the last thing you were doing was listening to a CD you are now ready to listen to a CD again If you wish you can change to another source W if you were listening to the Tuner last the Tuner comes on play ing the station it was last set to Note When power is supplied from the batteries the button on the Remote Control does not work Turning the Unit Standby Press the button again When operating on AC power d l STANDBY ON O GOOD BYE is displayed and the display becomes blank except for the clock display The STANDBY indicator lights up 3 MULTIJOG ZN A VOLUME cont
4. coloured blue must be connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the termi nal which is marked with the letter L or coloured red IF IN DOUBT CONSULT A COMPETENT ELECTRICIAN Caution switch Disconnect the mains plug to shut the power off completely The W switch in any position does not disconnect the mains line The power can be remote controlled Caution Proper Ventilation IMPORTANT FOR LASER PRODUCTS REPRODUCTION OF LABELS CLASSIFICATION LABEL PLACED ON EXTERIOR SURFACE CLASS 1 LASER PRODUCT WARNING LABEL PLACED INSIDE THE UNIT CLASS 1 LASER PRODUCT CAUTION Invisible laser radiation when open and interlock failed or defeated Avoid direct exposure to beam CAUTION Do not open the top cover There are no user service able parts inside the Unit leave all servicing to qualified service personnel CAUTION To reduce the risk of electrical shocks fire etc 1 Do not remove screws covers or cabinet 2 Do not expose this appliance to rain or moisture To avoid risk of electric shock and fire and to prevent damage locate the apparatus as follows 1 Front No obstructions and open spacing 2 Sides Top Back No obstructions should be placed in the areas shown by the dimensions below 3 Bottom Place on the level surface Maintain an adequate air path for ventilation by placing on a stand with a heigh
5. is supplied to the Unit Notes The clock must be correctly set for the timer to work e The clock may gain or lose 1 to 2 minutes per month e Perform each setting step within 30 seconds Otherwise setting is cleared and the procedure must be repeated from the beginning MULTIJOG MULTIJOG CLOCK VOLUME CLOCK VOLUME CLOCK DISPLAY Wo S4 DISPLAY iy Ss DISPLAY Q ON 2 ON mI Aru me C o lo o 5 LLULM UN AV AV oN o for 3 sec SLEEP CLOCK DISPLAY or l CD TUNER TIMER 75n S ALARM TIMER L snoozemmmer _ EaR SNOOZE DIMMER RD T7RGN SNOOZE E RD T5RBU Timer 2 indicator MULTIJOG VOLUME mN ae 9 ig BASS Jog dial TREBLE N Timer 1 indicator o Display when using the Timer On the Unit 1 Press the CLOCK DISPLAY button for 3 sec onds or more The hour digits blink 2 Turn the Jog dial to set the hour 3 Press the CLOCK DISPLAY button The minute digits blink 4 Turn the Jog dial to set the minute 5 Press the CLOCK DISPLAY button CLOCK OK appears for 2 seconds The selected time is set and the seconds start counting from 0 Setting the CD Tuner Timer The CD Tuner timer is turned on at the set time so that you can wake up to music from a CD or tuner The volume fades in when the Unit turns on The System will automatically turn off in 1 hour Note Perform each setting step within 30 seconds Otherwise settin
6. mains plug when making or changing connections Do consult your dealer if you are ever in doubt about the installation operation or safety of your equipment Do be careful with glass panels or doors on equipment Fe ee ae aie Bie he ee ee a a oe oe oe he oe oe oe ee oh ok ok ok ok ok oe ok ok DON T continue to operate the equipment if you are in any doubt about it working normally or if it is damaged in any way switch off withdraw the mains plug and consult your dealer DON T remove any fixed cover as this may expose dangerous voltages DON T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended opera tion or has a standby mode Switch off using the switch on the equipment and make sure that your family know how to do this Special arrangements may need to be made for infirm or handicapped people DON T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety It is illegal to watch television whilst driving DON T listen to headphones at high volume as such use can permanently damage your hearing DON T obstruct the ventilation of the equipment for example with curtains or soft furnishings Overheating will cause damage and shorten the life of the equipment DON T use makeshift stands and NEVER fix legs with wood screws to ensure complete safety always fit the manufacturer s approved stand or legs
7. playback press the lt lt or gt button to select the track you want The selected track starts playing e Press and release the gt I button to go forward one track at a time e Press and release the lt lt button to go back one track at a time W You can also skip the tracks in Stop mode Search Play During playback hold down the lt lt or gt button This operation will fast forward backwards the CD so you can quickly find a particular passage in the track you are listening to the CD is played slowly for a moment and then the playback speed in creases Locating a Track directly with the Remote Control Using the number keys on the Remote Control allows you can go directly to the beginning of any track During playback enter the number of the track you want to listen to using the number keys The selected track starts playing e Example For track 5 press 5 For track 15 press 10 then 5 For track 20 press 10 then 10 For track 32 press 10 three times then 2 8 RANDOM Play The tracks will play in no special order when you use this mode On the Unit 1 in Stop mode press the RANDOM REPEAT button until the RANDOM indicator alone lights up on the display Each time you press the button the Random Repeat indicator changes as follows CG gt G ALL gt G RANDOM gt RANDOM Random Play mode blank display gt back to the beginning 2 Press the CD P11 button All th
8. the beginning The SLEEP indicator will stop blinking after 5 seconds and re mains on Then the display returns to the one before you set the Sleep Timer The Unit is now set to turn off after the number of minutes you have set To Confirm the Sleep Time When the SLEEP button is pressed the remaining sleep time is dis played After 5 seconds the original display returns To Cancel the SLEEP Timer Setting Press the SLEEP button until the SLEEP indicator goes off on the display Turning off the Unit also cancels the SLEEP Timer Care And Maintenance Handle your CDs carefully and they will last a long time Compact Discs compet Only CDs bearing these marks can be played DIGITAL AUDIO with this Unit COMPACT DIGITAL AUDIO REILE G ohie ReWritable e Continued use of irregularly shaped CDs heart shape octagonal etc can damage the Unit e Remove the CD from its case by holding it at the edges while pressing the case s center hole lightly e Do not touch the shiny surface of the CD or bend the CD e Put the CD back in its case after use to prevent warping e Be careful not to scratch the surface of the CD when placing it back in the case e Avoid exposure to direct sunlight temperature extremes and moisture e A dirty CD may not play correctly If a CD is dirty wipe it with a soft cloth in a straight line from center to edge CAUTION Do not use any solvent for example
9. timer settings repeat the setting procedure from the beginning Setting the Alarm Timer The Alarm timer alarm clock is turned on at the set time to wake you up Alarm tone fades in and 2 minutes later it s frequency be comes higher The alarm tone continues for 15 minutes and then au tomatically stops Note e Perform each setting step within 30 seconds Otherwise setting is cleared and the procedure must be repeated from the beginning On the Unit 1 Press the ALARM TIMER button The current hour digits blink Also the Timer 2 indicator TIMER2 blinks 2 Turn the Jog dial to set the hour 3 Press the ALARM TIMER button The current minute digits blink 4 Turn the Jog dial to set the minute 5 Press the ALARM TIMER button The current alarm tone blinks 6 Turn the Jog dial to set the alarm tone level The alarm tone level changes between LEVEL 1 and LEV EL 7 7 Press the ALARM TIMER button The Alarm timer is set and the Timer 2 indicator TIMER2 remains lit 11 8 Turn off the Unit Standby mode e When the set time comes the Unit automatically turns on and sounds an alarm tone for 15 minutes e During sounding an alarm tone the Timer 2 indicator TIMER2 blinks After that the indicator remains lit again To stop the alarm tone press the ALARM TIMER button or turn off the Unit To cancel the timer press the ALARM TIMER button to turn off the Timer 2 indicator TIM
10. ER2 To reactivate the timer repeatedly press the ALARM TIMER button until the Timer 2 indicator TIMER2 remains lit again To confirm the timer settings repeatedly press the ALARM TIMER button To change the timer settings repeat the setting procedure from the beginning 5 Minute Snoozing SNOOZE When the CD Tuner timer or Alarm timer turns on if you wish ac tivate 5 minute snoozing function to temporarily stop playing source or sounding an alarm tone While the timer is activating press the SNOOZE button CD Tuner timer The Unit turns off for 5 minute for snoozing Alarm timer The alarm tone stops for 5 minute for snoozing Note The maximum number of times to repeat snoozing for the CD Tuner timer is limited to 10 Setting the SLEEP Timer Use the Sleep Timer to turn the Unit off after a certain number of minutes when it is playing By setting the Sleep Timer you can fall asleep to music and know that your Unit will turn off by itself rather than play all night W You can only set the Sleep Timer when the Unit is on and a source is playing 1 Play back a CD or tune in to a desired sta tion 2 Press the SLEEP button The SLEEP indicator blinks 3 Set the length of time you want the source to play before shutting off e Each time you press the SLEEP button it changes the number of minutes shown on the display in this sequence 10 20 30 60 90 120 Cancelled back to
11. MW CD PORTABLE SYSTEM RD T7RGN RD T5RBU RD T7RGN Only ONS CL RDS For Customer Use Enter below the Model No and Serial No which are located either on the rear bot tom or side of the cabinet Retain this information for future reference Model No Serial No LVT0737 007A B Warnings Cautions and Others IMPORTANT for the U K DO NOT cut off the mains plug from this equipment If the plug fit ted is not suitable for the power points in your home or the cable is too short to reach a power point then obtain an appropriate safety approved extension lead or consult your dealer BE SURE to replace the fuse only with an identical approved type as originally fitted If nontheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately to avoid a possible shock haz ard by inadvertent connection to the mains supply If this product is not supplied fitted with a mains plug then follow the instructions given below IMPORTANT DO NOT make any connection to the terminal which is marked with the letter E or by the safety earth symbol or coloured green or green and yellow The wires in the mains lead on this product are coloured in accor dance with the following code Blue Neutral Brown Live As these colours may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is
12. beginning rae Will repeat one track C ALL Will repeat all the tracks 2 Press the CD gt il button Repeat playback starts To stop Repeat Play press the W button To cancel Repeat Play mode in Stop mode press the REPEAT button until the Repeat indicator goes out or press the W button Pressing the CD OPEN button to open the CD cover will also cancel Repeat Play mode Using the Timers SNOOZE DIMMER RD T7RGN Only The timers let you control listening a music source as well as an alarm tone Three types of timers are available CD Tuner Timer 7 TIMER1 Use this timer to wake you up to music from a CD or tuner Alarm Timer TIMER2 Use this timer as an alarm clock Sleep Timer Use this timer to fall asleep to music Your System turns off auto matically after a certain length of time CAUTION If memory backup batteries are ex hausted or not installed and the AC power cord is disconnected or there is a power failure time set tings will be erased from memory in approx half a day Then the display blinks 0 00 If this hap pens set the current time clock and perform the timer setting again Setting the Clock When the Unit is operated on AC power or batteries for the first time the time indication 0 00 will blink on the display and you need to set the clock You can set the clock whether the Unit is turned on or off Standby if the AC power
13. ct press the AHB Active Hyper Bass PRO button The BASS indicator lights up on the display To cancel the effect press the button again The BASS indicator goes out Tone Control BASS TREBLE You can control the tone by changing the bass and treble 1 Press the BASS TREBLE button until BASS or TREBLE appears on the display Each time you press the button the display changes as follows BASS TREBLE gt original display gt back to the beginning 2 Turn the Jog dial on the Unit or press the VOLUME button on the Remote Control to adjust the level The bass or treble level changes between 6 and 6 0 Flat TOC C F TOCC AC Ht Oo gt HIT TOC TM C E _ TOC Car PAC GLO O Fre gee ro To exit the tone control mode press the BASS TREBLE but ton until the original display appears or wait for 15 seconds To forcibly reset the bass and treble levels to 0 FLAT press the BASS TREBLE button for 2 seconds or more Showing the Time CLOCK DISPLAY While listening to a CD or the radio you can see the current time To display the clock press the CLOCK DISPLAY button on the Unit To return to the original display press the same button until the original display appears Note You need to set the clock first in order for it to work See Setting the Clock on page 10 Adjusting the Brightness DIMMER RD T7RGN Only When the Unit is operated on AC power you can adjust the bright
14. e When you operate your Unit on mains AC power the power source switches automatically from batteries to AC However you should remove the batteries when operating on AC power R6P SUM 3 AA 15F size batteries R20 D 13F size batteries How To Put Batteries In the Remote Control Match the polarity and on the batteries with the and markings in the battery compartment R6P SUM 3 AA 15F CAUTION Handle batteries properly To avoid battery leakage or explosion e Remove batteries when the Unit or the Remote Control will not be used for a long time e When you need to replace the batteries replace batteries at the same time with new ones e Do not use an old battery with new ones e Do not use different types of batteries together e Do not try to recharge non rechargeable batteries Using the Remote Control RD T7RGN Only The Remote Control makes it easy to use many of the functions of the Unit from a distance of up to 7m 23 feet away You need to point the Remote Control at the remote sensor on the Unit s front panel Note If you point the Remote Control from the slant direction the above distance will be shortened Remote sensor Connecting the AC Power Cord Firmly insert the AC power cord supplied with the System into the AC inlet on the back of the Unit CAUTIONS e ONLY USE THE JVC POWER CORD PROVIDED WITH THIS SYSTEM IN AC IN ORDER TO AVOID MALFUNCTION OR DAMAGE TO
15. e tracks are played back in random order once then the CD stops e During playback skip play and search play can be done in the similar manner as for Normal Play mode using the a lt or gt gt button To stop Random Play press the W button To cancel Random Play mode in Stop mode press the RAN DOM REPEAT button until the RANDOM indicator goes out or press the W button Pressing the CD OPEN button to open the CD cover will also cancel Random Play mode Repeat Play One track or all the tracks on a CD will play repeatedly when you use this mode On the Unit 1 in Stop mode press the RANDOM REPEAT button Each time you press the button the Random Repeat indicator changes as follows G gt G ALL gt G RANDOM gt RANDOM gt blank display gt back to the beginning Gi Will repeat one track GALL Will repeat all the tracks Q RANDOM Will repeat all the tracks in random order 2 Press the CD gt il button Repeat playback starts To stop Repeat Play press the W button To cancel Repeat Play mode in Stop mode press the RAN DOM REPEAT button until the Random Repeat indicator goes out or press the Hf button Pressing the CD OPEN button to open the CD cover will also cancel Repeat Play mode On the Remote Control RD T7RGN Only 1 in Stop mode press the REPEAT button Each time you press the button the Repeat indicator changes as follows Cc CG ALL gt blank display back to the
16. g is cleared and the procedure must be repeated from the beginning On the Unit 1 Press the CD TUNER TIMER button The current hour digits blink Also the Timer 1 indicator TIMER blinks 2 Turn the Jog dial to set the hour 3 Press the CD TUNER TIMER button The current minute digits blink 4 Turn the Jog dial to set the minute 5 Press the CD TUNER TIMER button The current source name blinks 6 Turn the Jog dial to set the source The source name alternates between CD and TUNER 10 7 Press the CD TUNER TIMER button The current volume level blinks 8 Turn the Jog dial to set the volume level The volume level changes between VOL 1 and VOL 31 9 Press the CD TUNER TIMER button The CD Tuner timer is set and the Timer 1 indicator TIMER1 remains lit 10 Prepare the music source according to the source set in step 6 CD Load a CD TUNER Tune to a station you want to listen to 11 Turn off the Unit Standby mode e When the set time comes the Unit automatically turns on and plays the source During this time the Timer 1 indicator TIMER blinks To cancel the timer press the CD TUNER TIMER button to turn off the Timer 1 indicator TIMER1 To reactivate the timer repeatedly press the CD TUNER TIM ER button until the Timer 1 indicator E TIMER remains lit again To confirm the timer settings repeatedly press the CD TUN ER TIMER button To change the
17. l ic gt jann T IMIJC li M d e b on 4 Repeat steps 1 3 for further presetting To change the preset stations repeat the same steps as above To Change the FM Reception Mode The STEREO indicator lights up and you can hear stereo effects when a program is broadcast in stereo However if an FM stereo broadcast is hard to receive or noisy you can select Monaural mode Reception improves but you lose any stereo effect Press the TUNER BAND button to select FM MONO mode The MONO indicator lights up on the display To restore the stereo effect press the TUNER BAND button to select FM Auto mode FM appears on the display The MO NO indicator goes out Receiving FM Stations with RDS You can use the RDS Radio Data System by using the CLOCK DISPLAY button on the Unit RDS allows FM stations to send additional signals with their regular program signals For example the stations send their station names and information about what type of program they broadcast such as sports or music etc However this unit can only receive the follow ing type of RDS signal PS Program Service shows commonly known station names What information can RDS signals provide The display shows RDS signal information that the station sends To show the RDS signals on the display Press the CLOCK DISPLAY button on the Unit while lis tening to an FM station Each time you press the butto
18. n the display changes to show infor mation in the following order CLOCK DISPLAY i gt PS Clock gt Frequency Example of characters displayed PS Program Service While searching WAIT PS and PS alternately appear on the display Then the RDS indicator lights up and the station name ap pears NO PS appears if no signal is sent Clock Current time appears on the display Station Frequency Station frequency non RDS service Notes e If searching finishes at once WAIT PS and PS will not ap pear on the display e RDS is not available for AM MW broadcasts On characters displayed When the display shows PS signals e The display shows upper case letters only e The display cannot show accented letters For example A may represent accented A s like SA A A and Using the CD Player Number keys REPEAT Cj CDrll CC Ct e 7 Jem YAS lt q REMOTE CONTROL RM SRDT7 RD T7RGN only Random Repeat indicator Display when using the CD Player You can use Normal Random or Repeat Play Repeat Play can be set to repeat all or just one of the tracks on the CD One Touch CD Player AC power only ME Just press the CDH button e The power is automatically turned on If a CD is already inserted CD is displayed and the CD will
19. pside down Put the CD in with the label side up Unable to operate the Remote Control e The path between the Remote Con e Remove the obstruction trol and the sensor on the Unit is blocked e The batteries have lost their charge e Replace the batteries functioned due to external electrical interference Specifications General Dimensions 438 mm X 175 5 mm X 261 5 mm W H D Mass Approx 2 5 kg without batteries Amplifier Output Power Max 5 W 2 5 W 2 5 W at 3 ohms 10 THD 4 W 2 W 2 W at 3 ohms Output Sensitivity Impedance 1 kHz Phones 32 ohms kohm 0 mW 20 mW ch output into 32 ohms Accessories Power Cord 1 Remote Control RM SRDT7 1 RD T7RGN Only Sina To a ial 90 dB Batteries for Remote Control R6 SUM 3 e l Wow And Flutter Unmeasurable AN OR RD RONO Power Specifications sabe Power Requirements AC 230 V 50 Hz Power Consumption 10 watts power on mode Tuning Range 87 5 MHz 108 0 MHz 1 8 watts in Standby mode AM Tuner Tuning Range MW 522 kHz 1 629 kHz Antenna Built in wire antenna for FM Built in ferrite core antenna tor AM Design and specifications are subject to change without notice Speakers 8cm X 2 4 ohms VICTOR COMPANY OF JAPAN LIMITED 2 EN 0501 TTMCREHIT
20. rol a Fe 00 dial o TREBLE Cope PHONES E Whenin Standby mode the Unit continues to a small amount of power to run the display ME To switch off the Unit completely unplug the AC power cord from the AC outlet When power is supplied from the batteries When the Unit is turned off with the button on the Unit the button on the Remote Control is ineffective the Standby in dicator lights up and the display is blank ME To switch off the Unit completely remove the batteries from the Unit Adjusting the Volume You can adjust the volume level between MIN 0 and MAX 32 when the Unit is turned on Turn the VOLUME control on the Unit to the right or left to in crease or decrease the volume level OR Press the VOLUME or button on the Remote Control to increase or decrease the volume level CAUTION DO NOT turn on the Unit and or start playing any source without first setting the VOLUME control to MIN 0 as a sudden blast of sound can damage your hearing For private listening Connect a pair of headphones to the PHONES jack No sound comes out of the speakers Be sure to turn down the volume before connecting or putting on headphones Reinforcing the Bass Sound AHB PRO RD T7RGN Only You can reinforce the bass sound to maintain rich full bass at low volume you can use this effect only for playback To get the effe
21. s you wake or fall asleep to music ME The CD Player can play back a CD R and CD RW How This Manual Is Organized e Basic information that is the same for many different functions e g setting the volume is given in the section Common Operations and not repeated under each function e The names of buttons controls are written in all capital letters e g TUNER BAND e If the button names on the Unit and the Remote Control are the same the description on which the button is used will be omitted e System functions are written with an initial capital letter only e g Normal Play Use the table of contents to look up specific information you require We ve enjoyed making this manual for you and hope it serves you in enjoying the many features built into your System IMPORTANT CAUTIONS 1 Where to place the Unit e Select a place which is level dry and neither too hot nor too cold between 5 C and 35 C e Leave sufficient distance between the Unit and a TV e Do not use the Unit in a place subject to vibrations 2 Power cord e Do not handle the power cord with wet hands e Some power is always consumed as long as the power cord is connected to the wall outlet e When unplugging the Unit from the wall outlet always pull the plug not the power cord 3 Malfunctions etc e There are no user serviceable parts inside In case of system failure unplug the power cord and consult your dealer e Do not insert any metallic object in
22. start playing from the first track e Ifno CD is inserted NO DISC is displayed on the dis play and the CD Player remains in Stop mode Normal Play 1 Press the CD OPEN button on the Unit The CD cover including the display opens 2 Place a CD with its label side up 3 Press the CD OPEN button again to close the CD cover e Pressing the CD cover lightly will also close it e To close the CD cover and directly start playback omit this step and go to the next step 4 Press the CD gt il button The first track of the CD begins playing The CD Player automatically stops when the last track of the CD has finished playing e During playback the track number being played and the play back time elapsed are shown on the display Track number Playback time elapsed CDr ll Track number l CD OPEN Playing time Preset number ILI C ILIC II JO ILI ALL RANDOM To stop playing the CD press the m button The following information for the CD is displayed Total playback time To pause press the CD Pll To cancel pause press the CD gt I again Play continues from the point where it was paused CAUTION Avoid getting your hand caught in the CD cover Notes e You can place an 8 cm 3 CD without an adaptor e Ifthe CD cannot be read correctly because it is scratched for example 0 0 00 appears on the display Skip Play lt lt or gt gt During
23. t of 10 cm or more Front view Side view 15 cm 15 cm 15 cm CAUTION 1 Do not block the ventilation openings or holes If the ventilation openings or holes are blocked by a newspaper or cloth etc the heat may not be able to get out 2 Do not place any naked flame sources such as lighted candles on the apparatus 3 When discarding batteries environmental prob lems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly G 1 Do not use this apparatus in a bathroom or places with water Also do not place any containers filled with water or liquids such as cosmetics or medi cines flower vases potted plants cups etc on top of this apparatus SAFETY INSTRUCTIONS SOME DOS AND DON TS ON THE SAFE USE OF EQUIPMENT This equipment has been disigned and manufactured to meet international safety standards but like any electrical equipment care must be taken if you are to obtain the best results and safety is to be assured Be Ae Be Ae ah he ah he he He he he he ae he he hee he he he AAA AA ah he hee ae he he a ae he oh ke oh oh amp Hr Do read the operating instructions before you attempt to use the equipment Do ensure that all electrical connections including the mains plug extension leads and interconnections between pieces of equipment are properly made and in accordance with the manufacturer s instructions Switch off and withdraw the
24. to W Youcan also switch from the CD Player to the radio by pressing the TUNER BAND button Tuning In a Station 1 Press the TUNER BAND button The Band and Frequency you were last tuned to appear on the display Each time you press the button the band changes as follows pi AUTO FM MONO AM gt 7 2 Select a station using one of the following methods W Manual Tuning Press the lt 4 or gt gt button repeatedly to move from frequency to frequency until you find the station you want laa gt gt d PTUNING o OR W Auto Tuning If you press and hold the a lt or gt gt button for one second or more the frequency changes down or up automatically until a station is found OR W Preset Tuning using the Unit Possible only after pre setting stations Press the P TUNING button to select the preset station After you have selected the preset number the band and the fre quency are displayed e Example Press the P TUNING button until the preset number 12 P 12 appears CI a 1 CM IMAC IL gt Til lda on OR MULTIJOG VOLUME E D fo N AT Display when using the Tuner W Preset Tuning using the Remote Control Possible only after presetting stations Select the station by entering its preset number on the number keys e Example For channel 5 press 5 For channel 15 press 10 then 5 For channel 25 press 10 twice then 5 For channel 30 press 10 t
25. to the System Table of Contents FES AUIS tar sacasecargacuvesivokesnansaes S 1 Specifications ccccseeeeseeeeseeeeseeeeeeeees Back cover How This Manual Is Organized cccccceeccceseeeeneeeeneseees l IMPORTANT CAUTIONS aaiiesssssnnsessssssersssssseressssssserssss 1 Gelling Starled seii a 2 Common Operations sasssssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnn 3 USINO the TUNGT siisii aaa 5 Using the CD Player cccccssssseseeeseeeseenseeeseees 8 Using the Timers nassnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 10 Care And Maintenance csssscsssssseeseeesseeseeees 12 Troubleshooting cccceeeeeeeeeesseeeeeeenees Back cover 1 Getting Started Accessories Check that you have all of the following items which are supplied with the System Power Cord 1 Remote Control 1 RD T7RGN Only Batteries for Remote Control 2 RD T7RGN Only If any of these items are missing contact your dealer immediately How To Put Batteries How To Put Batteries In the Unit 1 Open the battery cover on the back of the Unit by pulling it toward you while pressing the tabs as shown by the arrows 2 Put 3 memory backup batteries R6P SUM 3 AA 1I5F not supplied in the battery compartment in the order of 1 to 3 3 Put 6 batteries R20 D 13F not supplied in the battery compartment in the order of 1 to 6 as shown 4 Securely close the battery cover Not
26. ton 2 Press the lt lt or gt gt button to tune in a sta tion 3 Press the m button for 2 seconds or more The preset number and band frequency are alternately displayed for 5 seconds n al I J E e gt oT a a C hd If it Vt e _ on 4 Within 5 seconds repeatedly press the E but ton until the preset number you want appears then press and hold the m button until STORED appears on the display 5 Repeat steps 1 4 for further presetting To change the preset stations repeat the same procedure as above Manual Presetting Using the Re mote Control BAND laa gt gt l ma Cr gt Number key s gt hold for 2 seconds 1 Select a band by pressing the TUNER BAND button 2 Press the lt lt or gt gt button to tune in a station 3 Set the preset number by pressing and hold ing the number key on the Remote Control until STORED appears on the display e To preset numbers 1 to 10 Press the number key and hold it down for 2 seconds e To preset numbers 11 to 19 Press and release the 10 but ton then press the second number key 1 to 9 and hold it down for 2 seconds e To preset numbers 21 to 29 Press and release the 10 but ton twice then press the second number key 1 to 9 and hold it down for 2 seconds e To preset number 30 Press and release the 10 button 2 times then press and hold 10 button Example Preset number 12 cm al g y
27. wice then 10 e The band and the frequency are displayed 3 Turn the antenna for best reception e Kor FM broadcast extend the built in wire antenna e For AM broadcast turn the Unit itself For AM NN gt O HT ILTTTNTTATTTTMTTTATTTAM NE pz Presetting Stations You can preset up to 30 FM stations and up to 15 AM MW stations into memory Auto Presetting Using the Unit In each band you can automatically preset FM 30 AM MW 15 sta tions Preset numbers will be allocated as stations are found starting from the station currently tuned to and moving up the frequency gt a for 2 seconds 1 Select a band AM or FM by pressing the TUNER BAND button 2 Press the TUNER BAND button for more than 2 seconds AUTO appears and then auto presetting starts 3 Repeat steps 1 2 for the other band Mit you want to change any of the auto preset stations follow the procedure for Manual Presetting CAUTION To prevent the preset stations from being erased because of a power failure etc install mem ory backup batteries in the System See page 2 Otherwise they will be erased in approx half a day Manual Presetting Using the Unit Station Select TUNERBAND gt 4 m i gt P TUNING a Press amp hold gt PT G PT G P T G for 2 sec Preset No Select 1 Select a band by pressing the TUNER BAND but
28. with the fixings provided according to the instructions DON T allow electrical equipment to be exposed to rain or moisture ABOVE ALL NEVER let anyone especially children push anything into holes slots or any other opening in the case this could result in a fatal electrical shock NEVER guess or take chances with electrical equipment of any kind it is better to be safe than sorry G 2 Thank you for purchasing the JVC CD Portable System We hope it will be a valued addition to your home as well as to your outdoor life giving you years of enjoyment Be sure to read this instruction manual carefully before operating your new stereo system In it you will find all the information you need to set up and use the system If you have a query that is not answered by the manual please contact your dealer Features Here are some of the things that make your System both powerful and simple to use ME The controls and operations have been redesigned to make them very easy to use freeing you to just enjoy the music e With JVC s COMPU PLAY you can turn on the System and automatically start the Radio or CD Player with a single touch When power is supplied from AC compu pi av W The System incorporates AHB Active Hyper Bass PRO circuitry to faithfully reproduce low frequency sounds RD T7RGN Only MM A 45 station preset capability 30 FM and 15 AM MW in addition to auto seek and manual tuning ma user friendly timer let
Download Pdf Manuals
Related Search