JVC GD-191 User's Manual
Contents
1. GD 171 20 191 LCD MONITOR User s Guide MA LMU179V P NO OAMO0008 Please read this manual thoroughly before use and keep it handy for future reference CAUTION Changes or modifications not approved by JVC could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense IMPORTANT RECYCLING INFORMATION This product has a fluorescent lamp that contains mercury Disposal of these materials may be regulated in your community due to environmental considerations For disposal or recycling information please contact your local authorities or for USA the Electronic Industries Alliance http Awww eiae org e y 10 11 12 13 14 SAFETY INSTRUTIONS Read all of these instructions Save these instructions for later use Follow all warnings and ins2. gt AVOID HEAT Avoid placing the unit in direct sunshine or near a heating appliance gt TO ELIMINATE EYE FATIGUE Do not use the unit against a bright back ground and where sunlight or other light sources will shine directly on the monitor gt BE CAREFUL OF HEAVY OBJECT Neither the monitor itself nor any other heavy object should rest on the power cord Damage to a power cord can cause fire or electrical shock POWER CONNECTION The power supply voltage rating of this product is AC 120 V For U S A and Canada and AC 220 240 V For European countries Asian countries and United Kingdom The power cord attached conforms to the following power supply voltage and countries Use only the power cord designated to ensure safety and EMC regulations of each country Not all types of power cords are supplied to this product For European and For U S A and 5 Asian countries Canada AC 120 V T 220 240 V For United Kingdom 220 240 V This plug will fit only into a grounded power outlet If you are unable to insert the plug into the outlet contact your electrician to install the proper outlet Do not defeat the safety purpose of the grounded plug e This product should be operated only with the type of power source indicated on the label If you are not sure of the type of power supply of your home consult your product dealer or local electric power company Warning e Do not use the same power cord
3. 58 5 mm WxHxD l l Net Weight 14 57 x 12 32 x 2 2 inch 16 1 x 13 54 x 2 3 inch Without stand 3 1 kg 6 83lbs 3 9 kg 8 6 Ibs Outline Dimension 370 x 355 3 x 182 mm 409 x 372 8 x 182 mm WxHxD Net Weight 14 57 x 13 99 x 7 17 inch 16 1 x 14 68 x 7 17 inch With stand 4 3 kg 9 48lbs 5 0 kg 11 02 Ibs DC12V adapter Auto Switching AC100V 240V 50Hz 60Hz NOTE Technical specifications are subject to change without notice 15 APPENDIX D SUB CONNECTOR PIN ASSIGMENTS PIN ASSIGNMENT pmnan ewo o pe oo e 1 vswo e 2020900 ar 6 Z 4 1 TROUBLESHOOTING GUIDE TROUBLESHOOTING GUIDE Troubleshooting Troubleshooting Tip 1 Make sure if the power supply is connected property No picture 2 Turn on the power 3 Select the input signal right for the connected port The screen is too light or to dark Adjust the BRIGHTNESS l l l Press the AUTO button among buttons in the front The screen size will not fit for the PC input It is used only the PC signal l In the FUNCTION menu of the OSD menu Strange colors using the PC input perform AUTO ADJUST 2010 Victor Company of Japan Limited 16
4. INPUT Select Inputs can be set to VIDEO1 VIDEO2 S VIDEO and RGB mode INPUT 1 Press the SOURCE button and then A V button to move the source 2 Press the button to select the source VIDEO1 VIDEO2 S VIDEO RGB PICTURE MENU RGB SETUP CONTRAST BRIGHTNESS COLOR TINT SHARPNESS COLOR TEMP NORMAL FUNCTION SCAN MODE 4 FULL gt ENTER MENU EXIT 5 CONTROL and FUNCTIONS 1 Press the MENU button and then A V button to select the PICTURE menu 2 Press the gt button and then A button to select the adjustment item you need Press the gt button to active the item ex If you select the BRIGHTNESS then the below picture appears on the bottom of screen BRIGHTNESS 4 Press 4 gt to adjust the item 5 Press the Menu button to move to the previous menu NOTE TINT item is for the NTSC input only SOUND MENU PICTURE BASS TREBLE RGB SETUP FUNCTION gt ENTER MENU EXIT Ver 1 05F 1 Press the MENU button and then button to select the SOUND menu 2 Press the gt button and then A button to select the adjustment item you need 3 Press the button to active the item EX If you select the TREBLE then the picture below appears the screen TREBLE ee gt i 4 Press 4 gt to adjust the item 5 Press the MENU button to move to the previous menu s412 CONTROL and FUNCTIONS RGB SETUP MENU PIC
5. TURE POSITION V POSITION clock eae FUNCTION 1 Press the MENU button and then A button to select the RGB SETUP menu 2 Press the gt button and then A V button to select the adjustment item you need Press the gt button to active the item 4 Press 4 gt to adjust the item 5 Press the MENU button to move to the previous menu FUNCTION MENU PICTURE LANGUAGE BUTTON LC LOCK OSD TIME DEFAULT RGB SETUP a 1 05F 18 CONTROL and FUNCTIONS 1 Press the MENU button and then A V button to select the FUNCTION menu 2 Press the gt button and then A button to select the adjustment item you need 3 Press the gt button to select the item 4 Press the MENU button to move to the previous menu LANGUAGE Select the language ENGLISH FRANCE GERMAN ITALIAN SPANISH BUTTON LOCK Select Button lock ON don t work the Front key Release the button lock Push the A and arrow at the same time for 5 sec then the button is activated OSD TIME Select the OSD display time from 5 seconds to 30 seconds DEFAULT Select DEFAULT to set the monitor to the factory default values 14 APPENDIX SPECIFICATIONS VIDEO r 1280 1024 60Hz SXGA 85 85 75 85 R L T B Frequency H 31 63kHz Frequency V 55 75Hz Panel Lamp Life 50 000hours MECANICAL Outline Dimension 370 x 313 x 56 mm 409 x 344 x
6. ed the extension cord ampere rating Also make sure that the total of all products plugged into the wall outlet does not exceed 10 amperes Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock Never spill any kind of liquid on the product Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage points or other risks Refer all servicing to service personnel Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions A When the power cord or plug is damaged or frayed If liquid has been spilled into the product If the product has been exposed to rain or water D If the Product does not operate normally when the operating instructions are followed Adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore normal operation If the product has been dropped or the cabinet has been damaged 3 SAFETY INSTRUTIONS If the product exhibits a distinct change in performance indicating a need for service 15 The Main Plug is used as the disconnect device Make enough room for inserting and removing the power plug Place
7. for AC 120 V as for AC 220 240 V Doing so may cause malfunction electric shock or fire Note for United Kingdom power cord only The plug of United Kingdom power cord has a built in fuse When replacing the fuse be sure to use only a correctly rated approved type re fit the fuse cover Consult your dealer or qualified personnel How to replace the fuse Open the fuse compartment with the blade screwdriver and replace the fuse CONTENTS CONTENTS SAFETY 3 4 CAT TOWN senate tice 5 6 UN PAC 8 CONNECTING WITH EXTERNAL DEVICE 9 CONTROLS and FUNCTIONS 10 14 AFEN A 15 16 TROUBLESHOOTING GUIDE UNPACKING Remove the package cover and place the product on a flat and secure surface or in the installation location Check whether all the flowing device and accessories are included with the main system TFT LCD MONITOR POWER CORD N America 3PIN x 1 Warranty Card CONNECTING WITH EXTERNAL DEVICE REAR PANEL CONTROL o9 009000 000 11 10 9 8 7 6 5 4 3 1 DC 12V Power IN 2 RGB IN RGB signal input 3 VIDEO 1 AV1 IN Composite signal input for AV1 4 VIDEO 1 AV1 OUT Composite looping output for AV1 5 VIDEO 2 AV2 IN Composite signal input for AV2 6 VIDEO 2 AV2 OUT Composite looping output for AV2 7 AUDIO L IN Left side audio s
8. ignal input This input is for AV1 AV2 S VIDEO 8 AUDIO R IN Right side audio signal input This input is for AV1 AV2 S VIDEO 9 S VIDEO Y C IN Y C separated signal input 10 S VIDEO Y C OUT Y C separated signal looping output 11 PC STEREO IN Note When doing Looping out connection by more than 3 please use distributor CONTROL and FUNCTIONS KEY FUNCTIONS MENU SOURCE Y AUTO A 1 MENU Activates and exits the OSD 2 SOURCE V Select input source and move the OSD menu 3 AUTO A Move the OSD menu and auto adjustment of RGB source 4 4 VOL Decrease the level of volume and select and set the OSD menu 5 Increase the level of volume and select and set the OSD menu 6 001 Turns the power ON OFF There will a few seconds delay before the display appears The power LED next to the power switch lights with green when the power is turned ON The power is turned off by pressing the power switch again and the power LED goes Red 7 LED LENSE 10 CONTROL and FUNCTIONS OSD MENU DESCRIPTION MENU SELECTION 1 Press the MENU button to access the Main menu 2 Usethe V arrow buttons to highlight a selection 3 Press the button to select an item 4 Usethe arrow buttons to highlight a selection 5 Use the lt and gt arrow buttons to adjust the setting a selected item NOTE If you don t use RGB mode RGB SETUP menu is not selected
9. the apparatus as close to the outlet as possible 16 Be sure to install the monitor securely to prevent the monitor from falling over which may cause damage to the monitor or injury 17 Do not step on or hang on the product CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE REAR COVER NO USER SERVICEABLE PARTS INSIDE REFER TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is Intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence important Operating and maintenance servicing instruction in the literature accompanying the appliance CAUTION gt NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel DO USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard do not expose the unit to rain or moisture This unit is designed to be used in the office or home Do not subject the unit to vibrations dust of corrosive gases gt KEEP IN A WELL VENTILATED PLACE Ventilation holes are provided on the cabinet to prevent the temperature from rising Do not cover the unit or place anything on the top of unit
10. tructions marked on the product Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Do not use this product near water Do not place this product on an unstable cart stand or table The product may fall causing serious damage to the product and persons nearby Slots and openings in the cabinet and the back are provided for ventilation to ensure reliable operation of the product these openings must not be blocked by placing the product on a bed sofa rug or other similar surface This product should never be placed near or over a heat register This product should not be placed in a built in installation unless proper ventilation is provided This product should be operated from the type of power source indicated on the marking label If you are not sure of the type of power available consult your dealer or local power company This product is equipped with a 3 wire grounding type plug having a third grounding pin This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the purpose of the grounding type plug Do not allow anything to rest on the power cord Do not locate this product where persons will walk on the cord lf an extension cord is used with this product make sure that the total of the ampere ratings the products plugged into the extension cord do not exce
Download Pdf Manuals
Related Search