JVC WB-S623U User's Manual
Contents
1. WB S621U Pendant Mount WB S622U Wall Mount WB S623U Ceiling Bracket INSTRUCTIONS Thank you for purchasig this product To obtain the best results from your bracket read these instructions carefully before use retain the manual for future reference The INSTRUCTIONS section below is applicable to WB S621U WB S622U WB S623U Please refer to the installation procedures for the purchased product during installation For Customer Use Enter below the Serial No which is located on the body Retain this information for future reference Model No Serial No These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances IMPORTANT SAFEGUARDS oahWON N 17 18 Read all of these instructions Save these instructions for later use All warnings on the product and in the operating instructions should be adhered to Unplug this appliance system from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Do not use attachments not recommended by the appliance manufacturer as they may cause hazards Do not use this appliance near water for example near a bathtub washbowIl kitchen sink or laundry tub in a wet basement or near a swimming pool etc PORTABLE CART WARNING Do not place this appliance on an unstable cart stand or table The appliance may fall causing serious injury to a child or2. Mount 3 Mount the Pendant Mount to the Ceiling Attach the pendant mount to the ceiling CAUTION The camera may drop or images on the screen may appear shaky if the ceiling material is not strong enough In this case reinforce using a reinforcement materials 4 Connect the safety cable Upon removing the camera mounting plate attach the safety cable not supplied to the safety cable mount hole b 4 5 mm 1 8 at the interior of the top cover using the M4 Bolt not supplied and M4 Nut not supplied When attaching the camera mounting plate ensure that the Front mark on the camera mounting plate is facing a direction to the Front mark on the top cover CAUTION Pay particular caution to the length strength pull and material of the safety cable in use to prevent the plate from falling 5 Install the ceiling panel assembly for attach ing TK C625U E and VN C625U To install align the protruding part of the ceiling panel assembly with the ceiling panel assembly positioning hole near the Front mark of the camera mounting plate Ensure to tighten the screws 3 locations assembled to the ceiling panel assembly NOTE The screws are assembled to the ceiling panel assembly in such Top cover a way that they will not come off 6 Connect the Cables Connect cables to the camera For details please refer to INSTRUCTIONS section of the camera in use 7 Attach the camera s ceiling mount Not applicable to TK
3. C205 A U E and TK C205VP A U E Attach the camera s ceiling mount to the camera mounting plate using the 4 screws M4 x 20 mm supplied with the pendant mount Ensure that the FRONT mark on the camera mounting plate aligns with the Front mark on the ceiling mount WB S622U Wall Mount 1 Make a hole When a hole is not To route cables through the wall make a hole of 30 mm 1 1 8 in the wall a Front Mark made in the Well 2 Route the safety cable and other cables Open the cover and route the safety cable and other cables through this wall mount Please refer to About Fall Prevention for procedures to install the safety cable When a hole is not made in the wall route the cables pulled to the wall stand through the groove of the Wall Mount CAUTION The camera may drop or images on the screen may appear shaky if the ceiling material is not strong enough In this case reinforce using a reinforcement materials 3 Attach the wall mount to the wall Attach the wall mount to the wall cable 4 Connect the safety cable z Upon removing the camera mounting plate attach the safety cable not supplied to the interior of the top cover using the M3 screw Refer to About Fall Prevention When attaching the camera mounting plate ensure that the Front mark on the camera mounting plate is facing a direction to the Front mark on the top cover 2 3 Camera Mounting Plate 5 5 Insta
4. adult and symbol provided by RETAC serious damage to the appliance may fall causing serious injury to a child or adult and serious damage to the appliance Use only with a cart or stand recommended by the manufacturer or sold with the appliance Wall or shelf mounting should follow the manufacturer s instructions and should use a mounting kit approved by the manufacturer An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn Slots and openings in the cabinet and the back or bottom are provided for ventilation and to insure reliable operation of the appliance and to protect it from overheating these openings must not be blocked or covered The openings should never be VAS blocked by placing the appliance on a bed sofa rug or other similar surface This appliance should never be placed near or ars over a radiator or heat register This appliance should not be placed in a built in installation such as a bookcase unless proper ventilation is provided This appliance should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supplied to your home consult your dealer or local power company For appliance designed to operate from battery power refer to the operating instructions For added protection for this product during a lightning storm or when it
5. d WB S623U Accessories Same for WB S621U WB S622U and WB S623U MMass Body INSUHUCTIONS cis ca beside eset eerie hal neees Lae dE 1 e Screw M4 x 20 mn For mounting camera 4 e Ceiling Panel ASSY 2 ceecceeeeeeeeeteeteteeeeteeees 1 Wi Tabulation of mass combined mount and Camera WB S621U WB S621U 2 0 kg Applicable TK C625U TK C205U TK C205VPU VN C625U VN C655U Camera 1 3 kg 0 57 kg 1 3 kg 1 2 kg 2 2 kg Total mass 3 3 kg 2 57 kg 3 3 kg 3 2 kg 4 2 kg WB S622U WB S621U 1 8 kg Applicable TK C625U TK C205U TK C205VPU VN C625U VN C655U Camera 1 3 kg 0 57 kg 1 3 kg 1 2 kg 2 2 kg Total mass 3 1 kg 2 37 kg 3 1 kg 3 0 kg 4 0 kg WB S623U WB S621U 1 0 kg Applicable TK C625U TK C205U TK C205VPU VN C625U VN C655U Camera 1 3 kg 0 57 kg 1 3 kg 1 2 kg 2 2 kg Total mass 2 3 kg 1 57 kg 2 3 kg 2 2 kg 3 2 kg E Extrnal dimensions Unit mm inches Design and specifications are subject to change without notice E WB S621U i WB S622U 332 13 1 8 85 3 3 8 120 4 3 4 85 3 3B 3 38 4 6 5 4 1 4 Ceiling Mount Hole 1 2 14 9140 5 1 2 5 80 3 1 8 _60 23 8 rA ie Ti 185 7 1 4 115 41 2 i WB S623U 9160 6 1 4 JVC 2005 Victor Company of Japan Limited 4 04 5 4 0 1 8 Ceiling Mount Hole 9160 6 1 4 JVC is a Registered T
6. e In a place subject to vibration When attaching VN C625U VN C655U to this mount bracket please refer to the INSTRUCTIONS section of VN C625U VN C655U for procedures to install the converter unit Please refer to the INSTRUCTIONS section of the camera in use for procedures to attach the camera Installation Procedures These installation should be made by a qualified service person and should conform to all local codes These installation should be in accordance with the National Electrical Code ANSI NFPA 70 Use the appropriate mounting hardware for the surface selected WB S621U Pendant Mount When a hole is not made in the ceiling Groove Reinforcement Angle 2 Safety cable E DON J daD 1 Cables 4 Fall prevention Safety cable Mount 8 Hole p 4 5 mm per g aN Bolt M4 Nut M4 Front Mark Camera Mounting Plate oe of a al amp Ceiling Panel Assy Weenie Screws and VN C625U 5 3 locations Protruding Part FRONT Mark Ceiling Panel Assembly Positioning Hole 1 Make a hole in the ceiling To route cables through the ceiling make a hole of p 30 mm 1 1 4 in the ceiling 2 Route the safety cable and other cables Route the safety cable and cables that is attached to the reinforce ment angle through the pendant mount When a hole is not made in the ceiling route the cables through the groove of the pendant
7. h the camera s ceiling mount Not applicable to TK C205 A U E and TK C205VP A U E Attach the camera s ceiling mount to the camera mounting plate using the 4 screws M4 x 20 mm supplied with the ceiling bracket Ensure that the Front mark on the camera mounting plate aligns with the Front mark on the ceiling mount Ceiling Panel Assy for attaching Screws TK C625U E Protrudin i and VN C625U pert 9 3 locations About Fall prevention Safety cable not included Connect the reinforcement material or reinforcement angle to this camera to prevent it from falling For the used safety cable pay particular caution to the length strength pull material Safety cable 4 When the camera mounting plate is removed Specifications Attach the camera to the camera mounting plate Ensure that the Front mark on the camera mounting plate aligns with the Front mark on the camera For TK C625U E and VN C625U attach the ceiling panel assem bly to the camera mounting plate before installing the camera Mounting Hole A For TK C655E TK C676E VN C655U TK C205 A U E and TK C205VP A U E Mounting Hole B For TK C625U E and VN C625U Mounting gt gt Mounting Hole A Hole A A Mounting Hole B Ceiling Panel Assembly Positioning Hole E Operating temperature 10 C to 50 C 14 F to 122 F WB S621U 2 0 kg WB S622U 1 8 kg WB S623U 1 0 kg Ceiling Panel Assy 37 4 g Same for WB S621U WB S622U an
8. h the hole at madein the ceiling one side of the Ceiling Bracket Remove the cap covering the hole before routing the cables through CAUTION The camera may drop or images on the screen may appear shaky if the ceiling Reinforcement Angle material is not strong enough In this case reinforce using a reinforcement materials 3 Mount the ceiling bracket to the ceiling Mount the ceiling bracket to the ceiling Top cover 4 Connect the safety cable Upon removing the camera mounting plate attach the safety cable not supplied to the interior of the top cover using the M3 screw Refer to About Fall Prevention When attaching the camera mounting plate ensure that the Front mark on the camera mounting plate is facing a direction to the Front mark on the top cover Camera Mounting Plate Ceiling Panel snare fid 5 Install the ceiling panel assembly for attaching TK D C625U E and VN C625U To install align the protruding part of the ceiling panel assembly with the ceiling panel assembly positioning hole near the Front mark of the camera mounting plate Ensure to tighten the screws 3 locations assembled to the ceiling panel assembly NOTE The screws are assembled to the ceiling panel assembly in such a way that they will not come off 6 Connect the cables OG or aseetey uabamioeeo Connect cables to the camera For details please refer to INSTRUCTIONS section of the camera in use 7 Attac
9. is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges Do not allow anything to rest on the power cord Do not locate this appliance where the cord will be abused by persons walking on it Follow all warnings and instructions marked on the appliance Do not overload wall outlets and extension cords as this can result in fire or electric shock Never push objects of any kind into his appliance through cabinet slots as they mat touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the appliance Do not attempt to service this appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Unplug his appliance from the wall outlet and refer servicing to qualified service personnel under following conditions a When the power cord or plug is damaged or frayed b If liquid has been spilled into the appliance c If the appliance has been exposed to rain or water d If the appliance does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive w
10. ll the ceiling panel assembly for attaching TK C625U E and VN C625U To install align the protruding part of the ceiling panel assembly with the ceiling panel Protruding Screws Part 3 locations Ceiling Panel Assy Ceiling Panel assembly positioning hole near the Front mark of the camera mounting plate for attaching Assembly Ensure to tighten the screws 3 locations assembled to the ceiling panel assembly TK C625U E Positioning Hole NOTE and VN C625U The screws are assembled to the ceiling panel assembly in such a way that they will not come off 6 Connect the cables Connect cables to the camera For details please refer to INSTRUCTIONS section of the camera in use 7 Attach the camera s ceiling mount Not applicable to TK C205 A U E and TK C205VP A U E Attach the camera s ceiling mount to the camera mounting plate using the 4 screws M4 x 20 mm supplied with the wall mount Ensure that the Front mark on the camera mounting plate aligns with the Front mark on the ceiling mount WB S623U Ceiling Bracket 1 Make a hole in the ceiling Safety cable To route cables through the ceiling make a hole of 30 mm 1 1 8 in the ceiling Gabios 2 Route the safety cable and other cables Route the safety cable and other cables through the ceiling bracket Please 7 refer to About Fall Prevention for procedures to install the safety cable Whena hole is not When a hole is not made in the ceiling route the cables throug
11. ork by a qualified technician to restore the appliance to normal operation e If the appliance has been dropped or the cabinet has been damaged f When the appliance exhibits a distinct change in performance this indicates a need for service When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Upon completion of any service or repairs to this appliance ask the service technician to perform routine safety checks to determine that the appliance is in safe operating condition For USA and CANADA WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Information for USA This device complies with Part 15 of the FCC Rules Changes or modifications not approved by JVC could void the user s author ity to operate the equipment CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL INFORMATION FOR CANADA RENSEIGNEMENT POUR LE CANADA This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada The lightning flash with arrowhead symbol wi
12. rademark owned by Victor Company of Japan Limited JVC is a Registered Trademark in Japan the U S A the U K and many other countries Printed in China LWT0267 001B C
13. thin an equi lateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage emt F F Tal A within the product s enclosure that may be of sufficient magnitude to constitute Due to design modification data given a this instruction book a risk of electric shock to persons are subject to possible change without prior notice The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instruc tions in the literature accompanying the appliance Precaution Installing the Converter Unit This equipment is intended for indoor use only Do not use it outdoors or at places that are exposed to rain or moisture When using VN C625U or VN C655U attach using the clamping bracket inside the top cover of the converter unit supplied with the camera Do not attach devices other than TK C625U E TK C655E TK C676E TK C205 A U E TK C205VP A U E VN C625U and VN C655U to this mount bracket The suffix E of model No specifies the exclusive variant for European market Install this mount bracket horizontally Do not tilt it during use Converter Unit Do not install or use the unit in the following places e In a place exposed to rain or moisture e In a temperature outsside the operating temperature range 10 C to 50 C 14 F to 122 F e In a place where corrosive gasses are generated
Download Pdf Manuals
Related Search