JVC AX-V5BK User's Manual
Contents
1. Page 21 6 7 10 Press Control A V until DELAY appears on the display Press Control lt to adjust the delay time of the rear speaker output Each time you press the button the delay time changes as follows DELAY 1 DELAY 2 DELAY DELAY 1 Select this when the distance from you to your rear speakers is greater than that to the front speakers DELAY 2 Select this when the distance from you to your rear speakers is almost equal to that to the front speakers DELAY 3 Select this when the distance from you to your rear speakers is less than that to the front speakers Note When have selected 3CHLOGIC you cannot adjust the delay time Press Control A V until TEST appears on the display then press Control lt 1 gt to start checking the speaker output balance TEST starts flashing on the display and a test tone comes out of the speakers in the following order Left front Center Right front speaker speaker speaker Rear speakers Notes No test tone comes out of the rear speakers when you have selected 3CHLOGIC No test tone comes out of the center speaker when you select PHANTOM or OFF for the center mode If necessary adjust the speaker output balance as follows To adjust the rear speaker output level press Control A V until REAR2. 5 Press Control lt 1 to adjust the rear speaker output level Pressing Control lt decreases the output level up to 10 dB Pressing Control gt increases the output level up to 10 dB 6 Press Control A V until DELAY appears on the display 7 Press Control lt to adjust the delay time of the rear speaker output Each time you press the button the delay time changes as follows 7 DELAY 1 DELAY 2 DELAY SCH DELAY 1 Select this when the distance from you to your rear speakers is greater than that to the front speakers DELAY 2 Select this when the distance from you to your rear speakers is almost equal to that to the front speakers DELAY 3 Select this when the distance from you to your rear speakers is less than that to the front speakers To cancel the Hall surround select OFF in step 2 The HALL indicator goes off From the remote control Zeg 1 Press SURROUND ON OFF so that one of the surround mode indicators PRO LOGIC 3CH LOGIC HALL lights up on the display The previous mode is recalled at its previous settings and is shown on the display Each time you press the button the surround mode turns on and off Ke AUDIO CONTROL 2 Press AUDIO CONTROL so that 10 keys work for adjusting the sound Press SURR MODE until HALL appears on the display The HALL indicator als
3. After pressing TAPE you can perform the following operations on a cassette deck gt Starts playback Lea Fast winds a tape from right to left gt gt Fast winds a tape from left to right EI Stops operation Pauses To resume playing press Page 25 IMPORTANT To operate JVC video components using this remote control e Aim the remote control directly at the remote sensor on the VCR or TV not on the amplifier After pressing VCR you can perform the following operations on a VCR gt Starts playback Fal ow A vn Lea Rewinds a video tape gt gt Fast winds a video tape ic EI Stops operation Pauses To resume playing press gt ree CH Changes channels on a VCR CW we ug Without pressing VCR you can always perform the following d Le VCR in the Standby On section CG Turns on off the VCR ic After pressing TV in the TV CONTROL section you can perform the following operations on TV CH Changes TV channels Without pressing TV in the TV CONTROL section you can always perform the following D anenee TV VIDEO Sets input mode either to TV or to VIDEO VOLUME in the TV CONTROL section Adjusts the volume TV in the O I Standby On section Turns on off the TV Page 26 Troubleshooting Use this chart to help you solve daily operational problems If there is any problem you cannot solve contac
4. EE ES To audio video output VCR yr tc te YY SE To audio video output Oooo EE Video disc player CAUTION If you connect a sound increasing device such as a graphic equalizer between the source components and the amplifier the sound output through the amplifier may be distorted Connecting Audio Components for the COMPU LINK 3 Remote Control System The COMPU LINK 3 remote control system allows you to control other JVC audio components from the amplifier or vice versa To use this system connect your JVC audio components and the amplifier with the cable monaural mini plug supplied with those components If your audio component has two COMPU LINK 3 SYNCHRO jacks you can use either one If it has only one COMPU LINK 3 SYNCHRO jack connect it so that it is the last item in the series of components for example the turntable and the tuner in the diagram below Notes The COMPU LINK 3 remote control system is the upgraded version of the COMPU LINK 1 and COMPU LINK 2 Even if your component has the COMPU LINK 1 or COMPU LINK 2 jacks you can still connect it in the COMPU LINK 3 remote control system but some functions may not work correctly For more information about the COMPU LINK 3 1 and 2 remote control system see page 24 Cassette deck Turntable Page 7 Connecting the Power Cord Before plugging the amplifier into an AC outlet make sure tha
5. appears on the display then press Control lt To adjust the center speaker output level press Control A V until CENTER appears on the display then press Control lt Notes The sound levels of the left and right rear speakers will be the same You cannot set the sound level of the rear speakers when have selected 3CHLOGIC You cannot set the sound level of the center speaker when you select PHANTOM or OFF for the center mode Press Control A V until TEST appears on the display then press Control lt gt to stop the test tone SURROUND ON OFF Ke AUDIO CONTROL CH SURR MODE sch DELAY sch TEST 4 REAR Ca E CENTER TEST 4 From the remote control If you have already set the center speaker size following the procedure described on page 13 you can use the remote control for Dolby Surround preparation 1 Press SURROUND ON OFF so that one of the surround mode indicators PRO LOGIC 3CH LOGIC HALL lights up on the display The previous mode is recalled at its previous settings and is shown on the display Each time you press the button the surround mode turns on and off Press AUDIO CONTROL so that 10 keys work for adjusting the sound Press SURR MODE until PROLOGIC or 3CHLOGIC whichever you want appears on the display Each time you press the button the surround modes chan
6. Design amp specifications are subject to change without notice Page 28 VICTOR COMPANY OF JAPAN LIMITED 2 EN GE FR NL SP IT 04970F YOTKJEM
7. Beim urspr nglichen Aufbau alle erforderlichen Anschl sse herstellen den Netzstecker in eine Wandsteckdose stecken und den POWER Schalter einschalten Anschlie end ist Betrieb der STANDBY ON W 1 usw m glich 2 Wenn das Ger t nicht verwendet wird den POWER Schalter ausschalten 3 Den Netzstecker aus der Steckdose ziehen um die Stromversorgung vollkommen zu unterbrechen Der POWER Schalter und die STANDBY ON Taste unterbrechen in keiner Stellung die Stromversorgung vollkommen 4 Die Stromversorgung kann mit der Fernbedienung ein und ausgeschaltet werden Attention Commutateur POWER et d une touche STANDBY ON Cetappareil est quip d un commutateur POWER qui lui permetde r duire sa consommation d lectricit pour une utilisation plus s re Par cons quent 1 En proc dant au r glage initial compl ter toutes les connexions n cessaires connecter la fiche secteur dans la prise murale et mettre le commutateur POWER sur la position ON Ensuite il sera possible de contr ler la touche STANDBY ON etc 2 Mettre le commutateur POWER sur la position OFF lorsque l appareil n est pas utilis 3 D connecterla fiche secteur pour couper compl tement le courant Le commutateur POWER et la touche STANDBY ON Oh ne coupent jamais compl tement l alimentation quelle que soit leurs positions 4 L alimentation peut tre t l command e G 3 Voorzichtig
8. Signal to Noise Ratio 66 IHF DIN RIAA Phono Equalization Loudness Volume Control at 40 dB Video Input Sensitivity VIDEO Impedance Video Output Level VCR MONITOR OUT Synchronization Signal to Noise Ratio General Power Requirements Power Consumption Dimensions W x H x D Mass 50 watts per channel min RMS driven into 4 ohms at 1 kHz with no more than 0 9 total harmonic distortion IEC268 3 DIN 30 watts per channel min RMS driven into 8 ohms at 1 kHz with no more than 0 9 total harmonic distortion IEC268 3 DIN 30 watts per channel min RMS driven into 8 ohms 40 Hz to 20 kHz with no more than 0 8 total harmonic distortion 40 watts per channel min RMS driven into 8 ohms at 1 kHz with no more than 0 8 total harmonic distortion 40 watts min RMS driven into 8 ohms at kHz with no more than 0 8 total harmonic distortion 40 watts per channel min RMS driven into 8 ohms at 1kHz with no more than 0 8 total harmonic distortion 0 8 at 30 watts output Measured by JVC Audio Analysis System 20 Hz to 20 kHz 1 dB 20 Hz to 20 kHz 1 dB 2 5 mV 47 k ohms 200 mV 47 k ohms 200 mV 70 dB 66 dB 87 dB 67 dB 0 5 dB 20 Hz to 20 kHz 5 2 dB at 100 Hz 1 Vp p 75 ohms 1 Vp p at 1 Vp p input negative 45 dB 230 50 Hz 240 watts 5 watts in standby mode 435 x 146 x 403 mm 17 3 16 5 3 4 x 15 7 sinches 8 0 kg 17 7 lbs
9. POWER en STANDBY ON 1 schakelaars Dit apparaat is voorzien van POWER hoofdschakelaar om het apparaat gebruiksklaar te zetten maar te zorgen dat het stroomverbruik minimaal blijft Neem in verband hiermee het volgende in acht 1 Bij de eerste ingebruikneming zorgt eerst dat alle aansluitingen in orde zijn dan steekt u de stekker in het stopkontakt en dan zet ude POWER schakelaar in de ON stand Daarna kunt u het apparaat aan en uitschakelen met de STANDBY ON schakelaar 2 Wanneer u het apparaat geruime tijd niet gebruikt kunt u beter de POWER schakelaar in de OFF stand zetten 3 de stroomtoevoer geheel uit te schakelen trekt u de stekker uit het stopkontakt Anders zal er altijd een geringe hoeveelheid stroom naar het apparaat lopen ongeacht de stand van de STANDBY ON de POWER 4 U kunt het apparaat ook met de afstandsbediening aan en uitschakelen Precauci n Interruptor POWER y bot n STANDBY ON 7 1 Esta unidad dispone de un interruptor POWER que sirve para reducir al m nimo el consumo de alimentaci n para proporcionar mayor seguridad operacional Por lo tanto 1 Al ejecutar el ajuste inicial despu s de completar todas las conexiones requeridas conectar el cable de alimentaci n a una toma de pared activar el interruptor POWER Entonces sera posible ejecutar operaciones tales la conmutaci n del estado de alimentaci n 2 Desactiva
10. Soe On the front panel only 1 Press SETTING so that the Control A lt 1 buttons work for setting the loudness The lamp above the button lights up 2 Press Control A V until LOUDNESS appears on the display 3 Press Control lt to set the loudness function to ON or OFF Select ON to activate the loudness function The LOUDNESS indicator lights up on the display e Select OFF to cancel it The indicator goes off Using the Sleep Timer you can fall asleep to music and know the amplifier will turn off by itself rather than play all night On the front panel only 59 1 Press SETTING so that the Control A V lt buttons work for setting the Sleep Timer The lamp above the button lights up 2 Press Control V until lt SLEEP gt appears on the display T 3 Press Control lt to set the shut off time Each time you press the button the shut off time on the display changes as follows and the SLEEP indicator lights up on the display fe 60 70 0 Canceled Continue to the next page Page 12 When the shut off time comes the amplifier turns off into standby mode automatically To check or change the tim
11. ohm impedance Page 5 Connecting the subwoofer speaker Connect the input jack of a powered subwoofer to the SUBWOOFER OUT jack on the rear panel using a cable with RCA pin plugs SUBWOOFER OUT Powered subwoofer Connecting Audio Video Components You can connect the following components to the amplifier using cables with RCA pin plugs Audio Components Video Components e Turntable e VCR CD player Video disc player e Cassette deck e TV Tuner Note Any turntables incorporating a small output cartridge such as an MC moving coil type must be connected to the amplifier through a commercial head amplifier or step up transformer Direct connection may result in insufficient volume Audio component connections Ifa ground cable is provided for your turntable connect the cable to the screw marked GND on the rear panel EN 7 7 11 0 os E To audio output monitor PHONO TUNERy CD TAPE REC IN PLAY To audio output 2 Turntable To audio output Cassette deck ENN Tuner To audio output Page 6 Video component connections S N A ei 2 To video input OT RT LN jour GND our PHONO TUNER y CD TAPE e 0 OUT IN OUT REC PLAY EE EE CCOO To audio video input E Besse
12. the mains supply If this product is not supplied fitted with a mains plug then follow the instructions given below IMPORTANT DO NOT make any connection to the terminal which is marked with the letter E or by the safety earth symbol or coloured green or green and yellow The wires in the mains lead on this product are coloured in accordance with the following code Blue Neutral Brown As these colours may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red IF IN DOUBT CONSULT A COMPETENT ELECTRICIAN G 1 CAUTION VOORZICHTIG To reduce the risk of electrical shocks fire etc Ter vermindering van gevaar voor brand elektrische schokken enz 1 Do remove screws covers or cabinet 1 Verwijder geen schroeven panelen of de behuizing 2 Do expose this appliance to rain or moisture 2 Stel dit toestel niet bloot aan regen of vocht ACHTUNG PRECAUCION Zur Verhinderung von elektrischen Schlagen Brandgefahr usw Para reducir riesgos de choques el ctricos incendio etc 1 Keine Schrauben l sen oder Abdeckungen enternen und nicht 1 No extraiga los tornillos los cubiertas ni la caja das Geh use ffnen 2
13. the power into standby mode press STANDBY ON O I again The STANDBY lamp lights up From the remote control To turn on the power press AUDIO AUDIO The STANDBY lamp goes off The name of the current source appears on the display To turn off the power into standby mode press AUDIO again The STANDBY lamp lights up Note Pressing STANDBY ON again turns off the power into standby mode and lights the STANDBY lamp A small amount of power is consumed in standby mode To turn the power off completely press POWER to set it in the HOFF position on the front panel Selecting the Source to Play On the front panel 1 Press SOURCE so that Control A buttons work for selecting the source The lamp above the button lights up Sra ed ia 2 Press Control until the source name you want appears on the display VOLUM From the remote control Press one of the source button directly le 4 gt U m CD Listen to the CD player TAPE Listen to the cassette deck connected to the TAPE jacks TUNER TUNER Listen to the radio View the video component connected to the VCR jacks VCR VIDEO View the video component connected to the VIDEO jacks PHONO Listen to a record lt 0 Note When you press one of the source buttons on the remote control marked above with an asterisk the amplifier automatically turn
14. CA pin plugs see page 6 Aim the remote control directly at the remote sensor on the amplifier After pressing TUNER you can perform the following operations 1 10 10 Selects a preset channel number directly For channel number 5 press 5 ie For channel number 15 press 10 then 5 For channel number 20 press 10 then 10 ep For channel number 30 press 10 10 then 10 ees RDS operating buttons Coli PTY SEARCH Starts and ends searching a broadcast using the RDS Coc PTY SELECT Selects a program type ZC DISPLAY Changes the RDS display mode TV CONTROL VOLUME C WC DELAY SURR MODE 5 6 gt e mjas After pressing CD you can perform the following operations on a CD player ea gt Starts playing PHONO OIC 5 lt lt Returns to the beginning of the current or previous track ote gt gt Skips to the beginning of the next track SVG usasa revor cono Stops playing ne Pauses To resume playing press gt 1 10 10 Selects a track number directly For track number 5 press 5 For track number 15 press 10 then 5 For track number 20 press 10 then 10 For track number 30 press 10 10 then 10 After pressing CD DISC you can perform the following operations on a CD player changer 1 6 7 P Select the number of a disc installed in a CD player changer Then continue to operate the CD player as described above
15. CHLOGIC whichever you want appears on the display SURR MODE Each time you press the button the surround modes change as follows 3CHLOGIC HALL The indicator of the selected surround mode lights up in turn as you select the surround modes 4 Select and play a sound source which was processed with Dolby Surround and is labeled with DU bowsysurrounp mark To cancel Dolby Surround press SURROUND ON OFF so that the indicator of the selected mode goes off Each time you press the button the surround mode turns on and off Page 23 COMPU LINK Remote Control System The COMPU LINK remote control system allows you to operate JVC audio components through the remote sensor on the amplifier To use this remote control system you need to connect JVC audio components through the COMPU LINK 3 SYNCHRO jacks with the cables monaural mini plug supplied with those components For details see page 7 Notes Without connecting the audio components with RCA pin plugs as described on page 6 the COMPU LINK remote control system cannot operate the components Refer also to the manuals supplied with your audio components This remote control system allows you to use the four functions listed below Remote Control through the Remote Sensor on the Amplifier You can control JVC audio components through the remote sensor on the amplifier using this remote control Aim the remote control direc
16. EE EENS EEEEEEE REENEN EE 17 Speaker Arrangements for Dolby Surround 0 eee eee ceeseeseesee ene 19 Preparing for Dolby Surround A 20 Using Dolby Surround ivi rokeros KE EEs EEEE EE estei ieir 23 COMPU LINK Remote Control System e seesesoesessesesseseosesoossesossesossesoesessesoesssoessssossesosses 24 Using the Remote Control ese sessesoesessesesseseesesoessesossesossesossessesoesesoessssossesossesoesessesosssessssses 25 Troubleshooting cccssrssssssssssscescesessssscesessesenessesessnssessessnssescessossescesesscscossesessnessessssesooss 27 SPCCHICATIONS ci scssesscosssssesvecasessosesocssseassoassaseesoooesessissessenssesssunsossssadseso sonseas 28 Switches Buttons and Controls Become familiar with the buttons and controls on the amplifier before use AX V5 AV INTEGRATED AMPLIFIER COMPU LINK MiiRemotelill e ONE TOUCH OPERATION STANDBY POWER PHONES SPEAKERS DELAY SURR MODE REAR 8 9 CD Coli CENTER 1 RM SAV5RU REMOTE CONTROL ENHANCED COMPULINK CONTROL SYSTEM Refer to the pages in parentheses for details
17. Front Panel Oli IN Remote sensor Display 9 MASTER VOLUME control 10 PRESET SEA button and lamp 15 SOURCE button and lamp 9 SURROUND button and lamp 17 20 23 ADJUST button and lamp 18 20 SETTING button and lamp 12 STANDBY ON button and STANDBY lamp 9 POWER switch 8 PHONES jack 11 SPEAKERS 1 2 buttons 10 Control A lt 1 gt buttons ONE TOUCH OPERATION button and lamp 14 Remote Control 15 25 26 27 28 TV VIDEO button 26 CH buttons 26 17 CD DISC button 25 AUDIO CONTROL button 16 18 22 23 Source buttons CD TAPE TUNER VCR VIDEO PHONO 9 25 26 VOLUME buttons 10 O I Standby On buttons TV VCR AUDIO 9 26 10 keys Audio control buttons 16 18 22 23 25 SEA ON OFF button 16 SURROUND ON OFF button 18 22 23 TV CONTROL buttons TV VOLUME 26 ONE TOUCH OPERATION button 14 Operating buttons for JVC audio video components 25 26 MUTE button 10 Page 2 Getting Started Before Installation This section explains how to connect stereo components and speakers to the amplifier and how to connect the power supply General Be sure your hands are dry Turn the power off to all components Rea
18. In this case 1 Select PROLOGIC 2 Select PHANTOM for center mode Rear Rear 5 Speaker See pages 20 to 22 for more details IER When you have added a center speaker without rear speakers Speaker Speaker Center Speaker SS SE SS SS In this case 1 Select 3CHLOGIC 2 Select NORMAL or WIDE for center mode See pages 20 to 22 for more details Page 19 Preparing for Dolby Surround SURROUND whale 0 PES The amplifier memorizes two sets of Dolby Surround adjustments one for Pro Logic and the other for 3ch Logic On the front panel 1 Press SURROUND so that the Control V buttons work for selecting the surround modes The lamp above the button lights up 2 Press Control V until PROLOGIC or 3CHLOGIC whichever you want appears on the display The PRO LOGIC or 3CH LOGIC indicator also lights up Each time you press the button the surround modes change as follows PROLOGIC 3CHLOGIC HALL EE OFF A The indicator of the selected surround mode lights up in turn as you select the surround modes PROLOGIC Select this mode when you use a center speaker and rear speakers 3CHLOGIC Select this mode when you use a center speaker without rear speakers HALL This is JVC s original surround mode
19. JVC AV INTEGRATED AMPLIFIER AV INTEGRIERTER VERSTARKER AMPLIFICATEUR INTEGRE AV GEINTEGREERDE A V VERSTERKER AMPLIFICADOR INTEGRADO DE AV AMPLIFICATORE INTEGRATO A V AX V5BK III Ser Self EI A BLINN Illi Remote lll For Customer Use BEDIENUNGSANLEITUNG Enter below the Model No and Serial MANUEL D INSTRUCTIONS No which are located either on the rear GEBRUIKSAANWIJZING bottom or side of the cabinet Retain this MANUAL DE INSTRUCCIONES information for future reference ISTRUZIONI Model No Serial No LET0023 001A EF G Warnings Cautions and Others Warnung Achtung und sonstige Hinweise Mises en garde precautions et indications diverses Waarschuwingen voorzorgen en andere mededelingen Avisos precauciones y otras notas Avvertenze e precauzioni da osservare IMPORTANT for the U K DO NOT cut off the mains plug from this equipment If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point then obtain an appropriate safety approved extension lead or consult your dealer BE SURE to replace the fuse only with an identical approved type as originally fitted If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately to avoid a possible shock hazard by inadvertent connection to
20. No exponga este aparato a la lluvia o a la humedad 2 Dieses Ger t weder Regen noch Feuchtigkeit aussetzen 2 ATTENTION ATTENZIONE Afin d viter tout risque d lectrocution d incendie etc Per ridurre il rischio di scosse elettriche incendi ecc 1 Ne pas enlever les vis niles panneaux et pas ouvrir le coffret 1 Non togliere viti coperchi o la scatola Ce de l appareil 2 esporre l apparecchio alla piogggia all umidita H 2 pas exposer l appareil la pluie ni a Bees 2 0 2 Caution POWER switch and STANDBY ON O I button This apparatus is provided with a POWER switch to be able to minimize power consumption for safe use Therefore 1 When doing initial setting complete all the connections required connect the mains plug into the wall outlet and set the POWER switch to ON After these it will be available to operate STANDBY ON O I button and so on 2 When not in use set the POWER switch to OFF 3 Disconnect the mains plug to shut the power off completely The POWER switch and STANDBY ON 1 1 button in any position do not disconnect the mains line 4 The power can be remote controlled Achtung POWER Schalter und STANDBY ON I Taste Dieses Ger t hat einen Netzschalter POWER um den Stromverbrauch f r sichere Verwendung auf ein Minimum bringen zu Verfahren Sie deshalb wie folgt 1
21. ST again to stop the test tone Page 22 Using Dolby Surround Once you have set the Dolby Surround adjustments you can use the same adjustments every time you want to enjoy Dolby Surround On the front panel 1 Press SURROUND so that the Control buttons work for selecting the surround modes The lamp above the button lights up 2 Press Control until PROLOGIC or 3CHLOGIC whichever you want appears on the display The PRO LOGIC or 3CH LOGIC indicator also lights up Each time you press the button the surround modes change as follows PROLOGIC 3CHLOGIC HALL EE The indicator of the selected surround mode lights up in turn as you select the surround modes 3 Select and play a sound source which was processed with Dolby Surround and is labeled with Doors susso mark To cancel Dolby Surround select OFF in step 2 above The indicator of the selected mode goes off From the remote control SCORES 1 Press SURROUND ON OFF so that one of the surround mode indicators PRO LOGIC 3CH LOGIC HALL lights up on the display The previous mode is recalled at its previous settings and is shown on the display Each time you press the button the surround mode turns on and off AUDIO CONTROL 2 Press AUDIO CONTROL so that 10 keys work for adjusting the sound 3 If necessary press SURR MODE until PROLOGIC or 3
22. The indicator of the selected mode also lights up on the display Press SETTING so that the Control A lt buttons work for selecting the center speaker size The lamp above the button lights up 4 Press Control until CNTR SPK Center Speaker appears on the display 5 Press Control lt to select the appropriate item about your center speaker Each time you press the button the display changes to show the following E lt lt NO 4 LARGE Select this mode when the size of the center speaker is the same as that of the front speakers SMALL Select this mode when the size of the center speaker is smaller than that of the front speakers NO Select this mode when you do not use a center speaker This mode cannot be selected when you select 3CHLOGIC Note This center speaker size setting is so related to the center mode setting for the Dolby Surround that changing this setting affects and changes the center mode to a relevant mode and vice versa For example Ifyou select LARGE the center mode is automatically set to WIDE and vice versa If you select SMALL the center mode is automatically set to NORMAL and vice versa Ifyouselect NO the center mode is automatically set to PHANTOM for PRO LOGIC and vice versa One Touch Operation This amplifier can memorize the optimum sound setting for eac
23. UNTRY Enhance the high frequency range so that instruments such the violin and banjo are emphasized OFF No preset SEA mode is applied See below To cancel the preset SEA mode select OFF in step 2 above The SEA indicator goes off from the display Page 15 SEA ON OFF Ke AUDIO CONTROL Ee SEA MODE ea PRESET 2 Ke From the remote control 1 Press SEA ON OFF so that the SEA indicator lights up on the display The previously selected mode is recalled at its previous effect level and is shown on the display Each time you press the button the preset SEA mode turns on and off Note When selecting the preset SEA mode the display will show the current effect level of the preset SEA mode selected Press AUDIO CONTROL so that 10 keys work for adjusting the sound Press SEA MODE until the mode you want appears on the display Each time you press the button the three preset SEA modes change as follows Ex cor 1 SPORTS2 JAZZ 2 7 Press PRESET to select the effect level Each time you press the button the effect level changes as follows When MOVIE is selected es 1 MOVIE 2 MOVIE 71 When SPORTS is selected SPORTS1 SPORTS2 SPORTS3 When MUSIC is selected E 1 JAZZ 2 ROCK 1 ROCK 2 1 UNTRY2 COUNTRY1 MUSICAL2 MUSICAL To cancel the preset SEA mode press SEA ON OFF so that the SEA indicator goes off fro
24. and is different from Dolby Surround To use this see page 17 OFF Select this to turn off the surround mode 3 Press ADJUST so that the Control A lt 1 buttons work for adjusting the selected surround mode The lamp above the button lights up 4 Press Control until CNT MODE Center Mode appears on the display 5 Press Control lt gt to select the center mode Each time you press the button the center modes change as follows NORMAL EH OFF WIDE Select this mode when the center speaker can reproduce the bass better than the front speakers All signals of the center channel are output through the center speaker NORMAL Select this mode when the center speaker cannot reproduce the bass better than the front speakers The bass portions of the center channel signals are output through the front speakers PHANTOM Select this mode when you do not use a center speaker The center speaker channel signals are output through the front speakers OFF Select this mode to turn off the center speaker channel Notes Ifyou have already set the center speaker size following the procedure described on page 13 you do not have to select the center mode in this procedure When you have selected 3CHLOGIC you cannot select PHANTOM Continue to the next page Page 20
25. d the manuals supplied with the components you are going to connect Locations Install the amplifier in a location that is level and protected from moisture The temperature around the amplifier must be between 5 and 35 23 and 95 F Make sure there is good ventilation around the amplifier Poor ventilation could cause overheating and damage the amplifier Handling the amplifier Do not insert any metal object into the amplifier Do not disassemble the amplifier or remove screws covers or cabinet Do not expose the amplifier to rain or moisture Checking the Supplied Accessories Page 3 Check to be sure you have all of the following items which are supplied with the amplifier The number in the parentheses indicates quantity of the pieces supplied e Remote Control 1 Batteries 2 If anything is missing contact your dealer immediately Connecting the Speakers You can connect the following speakers e Two sets of front speakers to produce normal stereo sound One set of rear speakers to enjoy the surround effect e One center speaker to produce more effective surround effect to make human voices outstanding One subwoofer to enhance the bass A For each speaker except for subwoofer connect one end of the speaker signal cable not supplied to the speaker terminal on the rear panel and the other end to the speaker For connecting a subwoofer see page 6 1 Open eac
26. dE Sata tev Moai inated 9 Selecting the Front Speakers cis 10 Adjusting the EE 10 Muting the EE 10 Recording a Source ai EE aici etek ae Basia ee Aeon eee 11 Listening with Headphones siaina a Sa a AEAEE CENE OAAR EERE 11 Basic Settings 12 Adjusting the Front Speaker Output Balance 12 Listening at Low Volume Loudness 0 00 0 eeccescecsseeeseceeneecseceeeecneeesaeceacecsaeeeneeeeeeeceeeeeeeeee 12 Using the Sleep EE sv scious 12 Selecting the Center Speaker Size c cssscesdescsscesesesssocesasesegssbdbs Cove svbestevapdbsadiseassesnconsescnentoase 13 Touch Operation cscccccsccsccssssssscssecsssssessssessscssscessessescesssssescesesssecessesessnessessssessoes 14 About the One Touch Operation 0 00 aeon ea e a a e E e 14 Using the Touch Operation e enei E enee 14 Using the Preset SEA Modes sscscscsssssssscessscscscsssccescssscescssssscsssssscsssssesssessessscesessseesesees 15 Selecting Your Favorite SEA Mode 15 Using the Surround Processor ccsscsssscssssssccsscecessscscescscsssscsssssssscssscsscsesesseseseeseesserseeees 17 Using JVC s Hall Surround 1 1eEeEEEENEEENEENN
27. e remaining until the shut off time 1 Press SETTING if necessary so that the Control A lt 1 gt buttons work for setting the Sleep Timer 2 Press Control A if necessary until lt SLEEP gt appears on the display 3 Press Control lt The remaining time until the shut off time appears in minutes To change the shut off time press Control lt gt repeatedly To cancel the Sleep Timer press Control lt repeatedly in step 3 above until 0 appears on the display The SLEEP indicator goes off Turning off the power into standby mode also cancels the Sleep Timer Selecting the Center Speaker Size yi5 Ge 5 Page 13 You can register the information about the center speaker after all connections are completed If you do this registration first you do not have to adjust the center speaker mode when you want to activate the surround sound However to register the information first you have to set the surround mode either to PROLOGIC or 3CHLOGIC You cannot select the center speaker size when the surround mode is OFF or HALL On the front panel only 1 Press SURROUND so that the Control A buttons work for selecting the surround mode The lamp above the button lights up 2 Press Control A V until PROLOGIC 3CHLOGIC appears on the display
28. er modes give you control over the way your music sounds Note The preset SEA mode cannot be used for recording Selecting Your Favorite SEA Mode On the front panel me 1 Press PRESET SEA so that the Control A lt buttons work for preset SEA setting AN The lamp above the button lights up 2 Press Control A V until the mode you want appears on the display The SEA indicator also lights up on the display Each time you press the button the preset SEA modes change as follows EE OFF Note When you turn on the preset SEA mode the mode and its effect level previously selected is recalled at first 3 Press Control lt 1 to select the effect level Each time you press the button the effect level changes as follows When MOVIE is selected 1 MOVIE 2 MOVIE j When SPORTS is selected SPORTS1 SPORTS2 SPORTS3 7 When MUSIC is selected 1 2 JAZZ 2 lt gt ROCK 1 ROCK SCH COUNTRY2COUNTRY1 lt MUSICAL 2 MUSICAL1 MOVIE Adds breadth to sounds so you feel like you are in a movie theater SPORTS Makes sound exciting MUSIC Select one of the modes below JAZZ Gives a feeling of a live atmosphere Good for acoustic music ROCK Gives a heavy sound Both high and low frequencies are boosted MUSICAL Enhances the mid frequency range which the human voice is mostly made up of CO
29. ers does not differ depending on whether both the FRONT SPEAKERS 1 and FRONT SPEAKERS 2 terminals are used or only one of them is used The required speaker impedance of the front speakers differs depending on whether or not a center or rear speakers are connected at the same time Since there are four possible speaker connections with the amplifier check which one fits your case and use the speaker with the impedance described below INN When you connect only front speakers Front Front Speaker Speaker Use front speakers with 4 16 ohm impedance GEIER When you connect front speakers and a center speaker Front Front Speaker Speaker Center Speaker Ld Sa ee Use the following speakers Front speakers 8 16 ohm impedance e Center speaker 8 16 ohm impedance WEIER When you connect front and rear speakers Front Front Speaker Speaker SZ Rear Rear Speaker Speaker Use the following speakers Front speakers 8 16 ohm impedance Rear speakers 8 16 ohm impedance WEIER When you connect front and rear speakers as well as a center speaker Front Front Speaker Speaker Center Speaker L SN K pee Rear Use the following speakers Front speakers 8 16 ohm impedance e Rear speakers 8 16 ohm impedance e Center speaker 8 16
30. ge as follows 3CHLOGIC HALL J The indicator of the selected surround mode lights up in turn as you select the surround modes Press DELAY to adjust the delay time of the rear speaker output Each time you press the button the delay time changes as follows ES DELAY 1 DELAY 2 DELAY 7 Note When you have selected 3CHLOGIC you cannot adjust the delay time Press TEST to start checking the speaker output balance TEST starts flashing on the display and a test tone comes out of the speakers in the following order Left front Center Right front speaker speaker speaker Rear speakers Notes No test tone comes out of the rear speakers when have selected 3CHLOGIC No test tone comes out of the center speaker when you select PHANTOM or OFF for the center mode If necessary adjust the speaker output balance as follows To adjust the rear speaker output level press REAR To adjust the center speaker output level press CENTER Pressing decreases the output level up to 10 dB Pressing increases the output level up to 10 dB Notes The sound levels of the left and right rear speakers will be the same e You cannot set the sound level of the rear speakers when have selected 3 CHLOGIC You cannot set the sound level of the center speaker when you select PHANTOM or OFF for the center mode Press TE
31. h playing source About the One Touch Operation JVC s One Touch Operation function is used to assign and store different sound settings for each different playing source By using this function you do not have to change the settings every time you change the source The stored settings for the newly selected source are automatically recalled The following can be stored for each source Volume level see page 10 Balance see page 12 e Loudness see page 12 e Preset SEA modes see page 15 Surround mode settings see page 17 Using the One Touch Operation To store the sound settings L Press ONE TOUCH OPERATION The ONE TOUCH OPERATION lamp lights up then the previously memorized settings are recalled ONETOUCH and appear on the display in turn ONE TOUCH OPERATION N 2 Adjust the sound using the functions listed above The newly adjusted settings are memorized On the front From the panel remote control To recall the sound settings With the ONE TOUCH OPERATION lamp lit the settings for the currently selected source is recalled and appears on the display when the source is selected To cancel the One Touch Operation function Press ONE TOUCH OPERATION so that the lamp goes off Even though the One Touch Operation function is canceled the recalled sound effects remain active Page 14 Using the Preset SEA Modes The preset SEA Sound Effect Amplifi
32. h terminal 2 Insert the end of the speaker signal cable as shown be sure to remove the insulation at the end of each wire first 3 Close the terminals to clamp the speaker signal cables firmly in place 4 Connect the black and red terminals on the rear panel to the black CX and red terminals marked on the speakers CAUTION When connecting speakers use speakers with the same SPEAKER IMPEDANCE indicated by the speaker terminals Connecting the front speakers Connect the front speakers to the FRONT SPEAKERS terminals EI GER SPEAKERS 1 FRONT SPEAKERS RIGHT LEFT e Left Speaker Right Speaker D SPEAKERS 2 GR Connecting the rear and center speakers Connect rear speakers to the REAR SPEAKERS terminals and a center speaker to the CENTER SPEAKER terminals Left Rear Right Rear Center Speaker SPEAKER es Speaker Speaker e SPEAKERS Note When you connect rear speakers make sure that both left and right speakers are connected otherwise no sound will come out of the rear speakers Page 4 About the speaker impedance of the speakers CAUTION the speaker terminals When connecting speakers use speakers with the same SPEAKER IMPEDANCE indicated by Notes The required speaker impedance of the front speak
33. in 10 cm from the top Back No obstructions in 15 cm from the back Bottom No obstructions place on the level surface In addition maintain the best possible air circulation as illustrated Achtung Angemessene Ventilation Stellen Sie das Ger t zur Verh tung von elektrischem Schlag und Feuer und zum Schutz gegen Besch digung wie folgt auf Vorderseite Offener Platz ohne Hindernisse Seiten Keine Hindernisse innerhalb 10 cm von den Seiten Oberseite Keine Hindernisse innerhalb 10 cm von der Oberseite R ckseite Keine Hindernisse innerhalb 15 cm von der R ckseite Unterseite Keine Hindernisse Auf eine ebene Oberfl che stellen Zus tzlich die bestm gliche Luftzirkulation wie gezeigt erhalten Attention Ventilation Correcte Pour viter les chocs lectriques l incendie et tout autre d g t Disposer l appareil en tenant compte des imp ratifs suivants Avant Rien ne doit g ner le d gagement Flancs Laisser 10 cm de d gagement lat ral Dessus Laisser 10 cm de d gagement sup rieur Arri re Laisser 15 cm de d gagement arri re Dessous Rien ne doit obstruer par dessous poser l appareil sur une surface plate Veiller galement a ce que l air circule le mieux possible comme illustr Spacing 15 cm or more Voorzichtig Zorg Voor Goede Ventilatie Om gevaar voor brand of een elektrische schok te voorkomen dient u bij opstelling van het apparaat op de volgende punten te letten Voorkant Voldoende ruimte v
34. m the display Each time you press the button the preset SEA mode turns on and off Page 16 Using the Surround Processor The built in surround processor provides three types of surround programs Dolby Pro Logic Dolby 3 Channel Logic and JVC s Hall Surround What is surround The sound heard in a concert hall or a movie theater consists of direct sound and indirect sound early reflections and reflections from behind The reflected sounds are always delayed by the distances of the ceiling and walls from the listener These reflections are some of the most important elements of the acoustic surround On JVC s Hall Surround In order to reproduce a more realistic sound field in your listening room while playing an ordinary stereo source JVC s Hall Surround has been designed to give you clear vocals to create Reflections feeling of a concert hall The sound is reproduced through the front speakers and rear speakers from behind Early reflections On Dolby Surround Dolby Surround has been also developed to reproduce the important elements of the acoustic surround at home To watch the soundtracks of video software bearing the mark which includes the same encoded surround information as found in Dolby Stereo films the amplifier can provide you with 2 Dolby Surround programs Dolby Pro Logic and Dolby 3ch Logic Dolby Pro Logic Select this mode when
35. mote control put the two supplied batteries in first When using the remote control aim the remote control directly at the remote sensor on the amplifier 1 On the back of the remote control press down on the battery cover and slide it out 2 Insert batteries Make sure to observe the proper polarity to and to 3 Slide the cover EO R6P SUM 3 AA 15F t REP SUM 3 AA 15F If the range or effectiveness of the remote control decreases replace the batteries Use two 50 3 AA 15F type dry cell batteries CAUTIONS Follow these precautions to avoid leaking or cracking cells e Place batteries in the remote control so they match the polarity indicated to and to gt Use the correct type of batteries Batteries that look similar may differ in voltage Always replace both batteries at the same time Do not expose batteries to heat or flame Page 8 Basic Operations The following operations are commonly used when you play any sound source Turning the Power On and Off Standby On the front panel Se To turn the power press STANDBY ON 0 1 on The STANDBY lamp goes off The name of the current source appears on the display Ee Dusch M M M MI MI A DN IN DN DN DN DN ON Current source name appears Current volume level is shown here To turn off
36. o lights up on the display SURR MODE Each time you press the button the surround modes change as follows fee 3CHLOGIC HALL E The indicator of the selected surround mode lights up in turn as you select the surround modes gt REAR Co Press REAR to adjust the rear speaker output level Pressing REAR decreases the output level up to 10 dB gt Pressing REAR increases the output level up to 10 dB DELAY 5 Press DELAY to adjust the delay time 5 Each time you press the button the delay time changes as follows KS DELAY 1 DELAY 2 DELAY To cancel the Hall Surround press SURROUND ON OFF so that the HALL indicator goes off Each time you press the button the surround mode turns on and off Page 18 Speaker Arrangements for Dolby Surround The following illustrations show how to obtain the optimum sound environment for various Dolby Surround settings Try to find the speaker direction and location to create the optimum sound field 77 0 When you have added a center speaker and rear speakers Front TV Front Speaker Speaker Center Speaker SS Sy Q In this case 1 Select PROLOGIC 2 Select NORMAL or WIDE for center mode Rear Rear See pages 20 to 22 for more details Speaker IER When you have added rear speakers without a center speaker Front Front Speaker Speaker Y 2 2
37. on at the same time the synchronized recording feature will not operate 3 Press the play gt button on the CD player on the turntable The source changes on the amplifier and as soon as play starts the cassette deck starts recording When the play ends the cassette deck enters recording pause and stops 4 seconds later Notes During synchronized recording the selected source cannot be changed Ifyour CD player is playing inprogram mode a4 second blank is recorded between tracks so that the music scan feature of your cassette deck can be used on the recorded tape Ifthe power of any component is shut off during synchronized recording the COMPU LINK remote control system may not operate properly In this case you must start again from the beginning Refer also to the manuals supplied with your CD player and cassette deck Page 24 Using the Remote Control You can operate JVC audio and video components with the amplifier s remote control since control signals for components are preset in the remote control To operate these components with the remote control first select a source with the source buttons on the remote control Then operate that source using the remote control IMPORTANT To operate JVC audio components using this remote control You need to connect JVC audio components through the COMPU LINK 3 SYNCHRO jacks see page 7 in addition to the connections using cables with R
38. r el interruptor POWER al dejar la unidad fuera de uso 3 Desconectar el cable de alimentaci n para desactivar la alimentaci n totalmente Cualquier que sea la posici n de ajustes del interruptor POWER el bot n STANDBY ON 0 1 la alimentaci n no es cortada completamente 4 La alimentaci n puede ser controlada remotamente Attenzione Interruttore POWER e tasto STANDBY ON Per ridurre al minimo l assorbimento di corrente ai fini della sicurezza questo apparecchio stato dodato di un interruttore POWER Di conseguenza 1 Al momento dellimpostazione iniziale completare tutti i collegamenti richiesti inserire la spina del cavo di alimentazione nella presa a muro della rete elettrica e impostare l interruttore POWER in posizione ON Fatto ci sar pronto all uso STANDBY ON 1 1 2 Quandononinuso impostare l interruttore POWER in posizione OFF 3 Disinserire la spina del cavo di alimentazione dalla presa della rete elettrica per staccare completamente l alimentazione L interruttore POWER il tasto STANDBY ON 0 1 in nessuna posizione staccano la linea di alimentazione elettrica principale 4 E possibile il controllo remoto dell alimentazione Caution Proper Ventilation To avoide risk of electric shock and fire and to protect from damage Locate the apparatus as follows Front No obstructions open spacing Sides No obstructions in 10 cm from the sides Top No obstructions
39. rij houden Zijkanten Minstens 10 cm aan weerszijden vrij houden Bovenkant Niets bovenop plaatsen 10 cm speling geven Achterkant Minstens 15 cm ruimte achteraan vrij houden Onderkant Opstellen op een egaal horizontaal oppervlak Bovendien moet er rondom voldoende luchtdoorstroming zijn zoals in de afbeelding aangegeven Precauci n Ventilaci n Adecuada Para evitar el riesgo de choque el ctrico e incendio y para proteger el aparato contra da os Ubique el aparato de la siguiente manera Frente Espacio abierto sin obstrucciones Lados 10 cm sin obstrucciones a los lados Parte superior 10 cm sin obstrucciones en la parte superior Parte trasera 15 cm sin obstrucciones en la parte trasera Fondo Sin obstrucciones col quelo sobre una superficie nivelada Adem s mantenga la mejor circulaci n de aire posible como se ilustra Attenzione Problemi di Ventilazione Per evitare il rischio di folgorazioni ed incendi e proteggere l unit da danni installarla nel modo seguente Davanti Nessun ostacolo spazio libero Lati Nessun ostacolo per almeno 10 cm Sopra Nessun ostacolo per almeno 10 cm Retro Nessun ostacolo per almeno 15 cm Fondo Libero ed in piano Inoltre mantenere il pi possibile la circolazione dell aria Abstand von 15 cm oder mehr D gagement de 15 cm ou plus Minstens 15 cm tussenruimte Espacio de 15 cm o m s 15 cm di distanza o pi Wall or obstructions Wand oder Hindernisse Mur ou obstr
40. s both SPEAKERS 1 and 2 to set them in the position If you do no sound comes out of the front speakers On the front panel To increase the volume turn MASTER VOLUME clockwise To decrease the volume turn it counterclockwise When you turn MASTER VOLUME rapidly the volume level also changes rapidly When you turn MASTER VOLUME slowly the volume level also changes slowly From the remote control To increase the volume press VOLUME To decrease the volume press VOLUME CAUTION Always set the volume to the minimum before starting any source If the volume is set at its high level the sudden blast of sound energy can permanently damage your hearing and or ruin your speakers From the remote control only Press MUTE to mute the sound through all speakers and headphones connected MUTE appears on the display and the volume turns off To restore the sound press MUTE again so that OFF appears on the display Turn MASTER VOLUME or pressing VOLUME also restores the sound at the previous volume level Page 10 Recording a Source You can record any source playing through the amplifier to a cassette deck connected to the TAPE jacks and VCR connected to the VCR jacks at the same time While recording you can listen to the selected sound source at whatever sound level you like without affecting the sound levels of the recording Note The output volume level preset SEA and s
41. s on 0 lt Page 9 Selecting different sources for picture and sound You can watch picture from video equipment while listening to sound from audio equipment To listen to the sound from audio equipment while watching the picture from video equipment 1 Select the video equipment as the source VIDEO or VCR 2 Press one of the source buttons for the audio equipment TUNER TAPE PHONO or CD on the remote control Selecting the Front Speakers SPEAKERS 1 Adjusting the Volume MASTER VOLUME _ N On the front panel CW VOLUME From the remote control Muting the Sound MUTE When you have connected two sets of front speakers you can select which to use Pressing SPEAKERS 1 or SPEAKERS 2 activates the respective set of speakers use the set of speakers connected to the FRONT SPEAKERS terminals press SPEAKERS 1 to set it in the position and press SPEAKERS 2 to set it in the HOFF position To use the set of speakers connected to the FRONT SPEAKERS terminals press SPEAKERS 2 to set it in the position and press SPEAKERS 1 to set it in the HOFF position To use both sets of speakers press both SPEAKERS 1 and 2 to set them in the position To use neither set of speakers press both SPEAKERS 1 and 2 to set them in the HOFF position Note When only one set of the front speakers is connected to either the FRONT SPEAKERS terminals do not pres
42. t your JVC service center PROBLEM POSSIBLE CAUSE SOLUTION The display does not light up The power cord is not plugged in Plug the power cord into an AC outlet or the O POWER switch is and press POWER to set it in the pressed to set in the HOFF position position No sound from speakers Speaker signal cables are not Check speaker wiring and connected reconnect if necessary The SPEAKERS 1 and 2 are not Press SPEAKERS 1 and 2 correctly set correctly An incorrect source is selected Select the correct source Sound from one speaker only Speaker signal cables are not Check speaker wiring and reconnect if connected properly necessary The balance is set to one extreme Adjust the balance properly see page 12 Howling during record Your turntable is too close to Move speakers away from the turntable playing speakers Remote control does not There is an obstruction in front of Remove the obstruction work the remote sensor on the amplifier Batteries are weak Replace batteries Page 27 Specifications Amplifier Output Power At Stereo Operation Front Channels At Surround Operation Front Channels Center Channel Rear Channels Total Harmonic Distortion 8 ohms 1 kHz PHONO TUNER CD TAPE VCR VIDEO Frequency Response 8 ohms Audio Input Sensitivity Impedance 1 kHz PHONO MM TUNER CD TAPE VCR VIDEO Audio Output Level TAPE VCR PHONO TUNER CD TAPE VCR VIDEO
43. t all connections have been made 1 Plug the power cord into an AC outlet EE 2 Press OPOWER to set it in the mON position The STANDBY lamp lights up A small amount of power is always consumed To shut off the power completely Press POWER to set it in the HOFF position Keep the power cord away from the connecting cables for the TV VCR and antenna The power cord may cause noise or screen interference The difference between the POWER switch and the STANDBY ON button The POWER switch is the mains supply switch allowing the amplifier to connect to the mains supply To shut off the power completely press the POWER switch to set it in the position The STANDBY ON O I button is a functional on off standby switch and does not disconnect the amplifier from the mains supply A small amount of power is consumed even in standby mode for the amplifier to accept signals from the remote control Notes The preset settings such as sound adjustment may be erased in the following cases When you press POWER to set it in the HOFF position When you unplug the power cord When a power failure occurs CAUTIONS Do not touch the power cord with wet hands Do not pull on the power cord to unplug the amplifier When unplugging the amplifier always grasp the plug itself so as not to damage the cord Putting Batteries in the Remote Control Before using the re
44. the optional rear speakers are connected as well as a center speaker Dolby 3ch Logic Select this mode when a center speaker is connected without rear speakers Notes The surround processor has no effect on monaural sources The surround processor cannot be used for recording Manufactured under license from Dolby Laboratories Licensing Corporation Dolby the double D symbol and Pro Logic are trademarks of Dolby Laboratories Licensing Corporation Using JVC s Hall Surround You need to connect one set of rear speakers to obtain the full effect Once you have adjusted the Hall Surround the amplifier memorizes the settings On the front panel 1 Press SURROUND so that the Control A lt buttons work for selecting the surround modes The lamp above the button lights up 2 Press Control A V until HALL appears on the display The HALL indicator also lights up on the display Each time you press the button the surround modes change as follows PROLOGIC 3CHLOGIC HALL Ee The indicator of the selected surround mode lights up in turn as you select the surround modes Page 17 SC 3 Press ADJUST so that the Control lt 1 buttons work for surround settings The lamp above the button lights up 4 Press Control V until REAR appears on the display
45. tly at the remote sensor on the amplifier For details see page 25 Automatic Source Selection When you start playing on a connected component the amplifier automatically turns and changes its source to the component On the other hand if you select a new source on the amplifier or the remote control the selected component begins playing immediately In both cases the previously selected source continues playing without sound for a few seconds Automatic Power On Off Standby only possible with the COMPU LINK 3 connection The audio components tuner CD player and cassette deck connected to the amplifier automatically turn on and off into standby mode with the amplifier When you turn on the amplifier one of the connected components will turn on automatically depending which component has been previously selected When you turn off the amplifier into standby mode these components connected will turn off into standby mode m Synchronized Recording Synchronized recording means the cassette deck starts recording as soon as a CD or record begins playing To use synchronized recording follow these steps 1 Puta tape in the cassette deck and a disc in the CD player or a record on the turntable 2 Press the record button and the pause II button on the cassette deck at the same time This puts the cassette deck into recording pause Note Ifyou donot press the record button and pause 11 butt
46. uction Wand of meubilair Pared u obstrucciones Parete o ostacol Front Vorderseite Avant Voorkant AX V5BK Frente Davanti Stand height 15 cm or more Standh he 15 cm oder mehr Hauteur du socle 15 cm ou plus Standard op minstens 15 cm van de vloer Allura del soporte 15 cm o m s Altezza del tavolino 15 cm p pl Floor Boden Plancher Vloer Piso Pavimento G 4 Table of Contents Page 1 Switches Buttons amd Controls e 2 Getting Started 3 Before Installation Seet Age EE ENEE Deeks eer 3 Checking the Supplied Accessories aeS 3 Connecting the Speakers eeneg ss ESA 4 Connecting Audio Video Components 0 0 0 0 cece ceceseeeeceseeeeceeceseceeeeeeseseeeaecseesaecaeesaecseeeaeenees 6 Connecting Audio Components for the COMPU LINK 3 Remote Control System 7 Connecting the Power Cord s ccscissscasssenssctpicscgessensscsucidpastaassosasessbsasbsssassasncdespscvensossessasuannsees 8 Putting Batteries in the Remote Control 8 Basic vccssceceveessesssessesscossenseasosesossssossssocesseessonebesontavedsosqudesosdudnsasseadoussoas casooseessoussesonas 9 Turning the Power On and Off 9 selecting the Source tO Play Gate ens
47. urround modes cannot affect the recording Listening with Headphones A standard pair of headphones can be connected to the PHONES jack on the front panel Besure to turn down the volume before connecting or putting on headphones as high volume can damage both the headphones and your hearing KEE To listen with only headphones Press both SPEAKERS 1 and 2 to set them in the HOFF position Page 11 Basic Settings Some of the following settings are required after connecting and positioning your speakers in your listening room while others will make operations easier Adjusting the Front Speaker Output Balance Ga If the sounds you hear from the front right and left speakers are unequal you can adjust the speaker output balance On the front panel only TF 1 Press SETTING so that the Control A lt buttons work for adjusting the balance Azad The lamp above the button lights up lt 4 gt ee 2 Press Control A V until BALANCE appears on the display 3 Press Control lt to adjust the balance A Pressing Control lt 1 decreases the right channel output lt gt Pressing Control gt decreases the left channel output Listening at Low Volume Loudness Human ears are not sensitive to bass at low volume To compensate for this the loudness function automatically boosts the bass level as you lower the volume
Download Pdf Manuals
Related Search