Jensen JiMS-182 User's Manual
Contents
1. POWER STANDBY Button to turn off the unit The radio will automatically turn on when the alarm time is reached Wake to iPod Briefly press ALM 1 MEM or ALM 2 MEM Button to select iPod mode E or will appear in the display Follow the procedure in DOCKING YOUR iPOD to play your iPod Press POWER STANDBY Button to turn the unit off When the alarm time is reached the iPod will automatically start playing i After waking to iPod or Radio alarm the volume level of the iPod or radio can be adjusted as needed ii After the alarm is on the LCD backlight will automatically be set to high Light The light located on the top of the JiIMS 182 works with all Wake to settings The light will begin to light one minute before the alarm time is reached and will increase to full brightness by the time the alarm time is reached Stopping the Alarm The alarm is programmed to continuously sound for 60 minutes To stop the alarm follow the directions below 1 SNOOZE DIMMER Button Press this button to stop the alarm temporarily The alarm will stop and automatically resume after 9 minutes 2 O POWER STANDBY Button Press this Button to stop the alarm which will sound again 24 hours later 3 ALM 1 MEM or ALM 2 MEM Button Press this Button once to stop the alarm and the alarm will sound again 24 hours later DIMMER Operation With AC Adaptor plugged in In power off mode press the SNOOZE DI2. You can play other music sources iPod shuffle 1 and ao generation MP3 CD or other digital audio player through the speakers of JIMS 182 by connecting the AUX IN Jack to your external player s LINE OUT jack or headphone jack 1 Plug one end of the connection cord Not included into the AUX IN jack on the back of JiMS 182 Plug the other end of the cord into your external audio player such as an iPod shuffle CD MP3 Player etc Power on JiMS 182 and the external player Press the FUNCTION Button to select the AUX mode Start playing your iPod shuffle MP3 CD or other digital audio player Slowly adjust both the volume on JiMS 182 and the external device Press the EQ Button repeatedly to choose the desired equalizer effect Turn off the attached player when finish listening Press the POWER STANDBY Button to turn JiMS 182 off and unplug the connection cord from the AUX IN jack iPod ADAPTORS There are three iPod Adaptors included in the package One for the iPod touch 2 generation and iPod nano 3 generation and 4 generation ONDARON For nano 3 generation For nano 4 generation For iTouch ge generation It is always recommended you use the adaptor that comes with your iPod first This will help maximize a custom fit for your iPod when docked To place the iPod adapter 1 Select an adaptor and gently place it into the dock Insert the hooks of the adaptor into the socket of the docking bay 2 Carefully push fo
3. ALARM1 and ALARM2 You can choose to use them independently or simultaneously ALARM 1 ALARM 2 or both ALARM 1 and ALARM 2 Alarm Time Setting Note Alarm time s can only be set in Power Off mode 8 3 4 To set the wakeup time press and hold the ALM 1 MEM or ALM 2 MEM Button for approximately 3 seconds until the hour digit blinks While the hour digit blinks press re or pei button to adjust your desired hour digit Note For the 12 Hour format Make sure the Hour is set so that AM or PM is correctly displayed Press ALM 1 MEM or ALM 2 MEM button to save the gt l z hour setting the minute digit will blink a While the minute digits blink press re or pei button to adjust your desired minute digit Press ALM 1 MEM or ALM 2 MEM button to save the wakeup setting Setting Wakeup Mode Press ALM 1 MEM or ALM M2 MEM Button repeatedly to select the desired wake up mode wake to Alarm RADIO or iPod for alarm 1 or alarm 2 1 Wake to Alarm Repeatedly press ALM 1 MEM or ALM 2 MEM Button to enter ALARM mode or will appear in the display Two different rings for Alarm 1 and Alarm 2 will sound when the alarm time is reached Wake to Radio Repeatedly press ALM 1 MEM or ALM 2 MEM Button to enter the RADIO mode T or T will appear in the display Follow the procedure in TUNER OPERATION to select your desired radio station Press the
4. or AUX function 1 Press the SLEEP Button repeatedly until the desired sleep time is shown on the Display For example if it is 10 00 PM and you set the sleep time for 30 minutes the display will show Preset Sleep Time Current time 2 The JiMS 182 will play and turn off automatically after the 30 minute Sleep time expires at 10 30 PM If you want to cancel the sleep time before the time expires press POWER STANDBY Button once 3 The Light can also be used during the Sleep mode Press the LIGHT Button once to turn on the Light The light will dim and go off when the preset sleep time expires Note In AUX Mode if the playing time of the external device is shorter than your selected sleep time the music will stop when the external device shuts off CARE AND MAINTENANCE 1 Clean the unit with a damp never wet cloth Solvent or detergent should never be used Avoid leaving your unit in direct sunlight or in hot humid or dusty places Keep your unit away from heating appliances and sources of electrical noise such as fluorescent lamps or motors 4 For better Clock Display clarity avoid operating the unit under direct sunlight or in strong room illumination on TROUBLESHOOTING GUIDE Should the system exhibit a problem please check the following before seeking service Symptom Possible Cause Solution Radio Noise or sound distorted on AM or FM broadcasting Station is not tuned properly
5. select 24 Hour format 24 H if desired 3 Press the MEMO SET button again to save the hour format setting The Hour digit will blink 4 While the Hour digit blinks press re or pei button repeatedly to set the current hour Note For 12 Hour format make sure the Hour is correctly set so that AM or PM is correctly displayed 5 Press the MEMO SET button again to save the hour setting The minute digit will blink 6 While the Minute Digit blinks press mea or pei button repeatedly to set the current minutes 7 Press the MEMO SET button again to complete the setting pE Jma cig TUNER OPERATION 1 Press the POWER STANDBY button once The System will enter the FM mode 1 2 Press the gt Il BAND button once to switch to AM if desired m l TO PRESS Switch between AM FM band gt Il BAND Button Scan radio station manually rea or PP repeatedly Scan radio station automatically Ke or gt gt and hold for 2 seconds Stop auto tuning kd OF PP once Control the volume A d Buttons TO PRESET CHANNELS This unit is equipped with 20 preset memories each for AM and FM Once they are preset they can be instantly accessed by briefly pressing the ALM 1 MEM or ALM 2 MEM Buttons Press the POWER STANDBY button to turn the System on Press the BAND Pll button to switch between AM or FM band Tune to a desired station Press the MEMO SET Button once The Prese
6. FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is needed Consult the dealer or an experienced radio TV technician for help WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment IMPORTANT NOTES Avoid installing the unit in locations described below e Places exposed to direct sunlight or close to heat radiating appliances such as electric heaters e Dusty humid or moi
7. JENSEN Docking Digital Clock Radio Music System For iPod iPod OWNER S MANUAL JiMS 182 iPod not included Please read this Instruction Manual carefully before using the unit and retain it for future reference IMPORTANT INSTRUCTIONS 1 Do not install the system near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 2 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 3 Only use attachments accessories specified in these instructions 4 Unplug this apparatus during lightning storms or when unused for long periods of time 5 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 6 This appliance shall not be exposed to dripping or splashing water and that no object filled with liquids such as vases shall be placed on the apparatus 7 Do not attempt to dismantle open or repair this product yourself If a fault occurs seek advice from your local qualified service technician or contact the distributor via the telephone number at the back of this instruction manual
8. MMER Button repeatedly to adjust the LCD backlight to low middle or high as desired Note i With the AC Adaptor plugged in and with power off press any button except SNOOZE DIMMER and the LCD backlight will automatically set to high and resume to the preset brightness in approximately 5 seconds ii If using battery power the LCD backlit is always set to the dimmest level in order to conserve battery power Press any button the LCD backlight will automatically set to high and resume to the dimmest level in approximately 5 seconds Turning the Lamp On Off 1 You can press the LIGHT button to turn the Lamp on and off 2 The Lamp will also light automatically one minute before the alarm time is reached and increase to the full brightest level when the alarm time is reached 3 When you stop the alarm by pressing the SNOOZE DIMMER POWER ALM 1 MEM or ALM 2 MEM Button the Lamp will be turned off at the same time You can also press the LIGHT Button to turn off the Lamp directly 4 Ifthe Lamp is on before waking to alarm radio or iPod when you stop the alarm by pressing the SNOOZE DIMMER POWER STANDBY ALM 1 MEM or ALM 2 MEM Buttons the Lamp will remain on To turn the Lamp off press the LIGHT Button once SLEEP OPERATION Your JiMS 182 can be programmed to turn off according to your preset sleep time The sleep time can be set for 15 30 60 90 or 120 minutes 10 Turn on the JiMS 182 on and select either iPod Radio
9. an AC 120V 60Hz power source e Note The batteries will be automatically disconnected when the AC adaptor is plugged into the DC Jack and the System will operate on AC power Note Unplug the AC adaptor and disconnect the DC Jack when the JiMS 182 is not in use for a long period of time C ACTIVATING THE BACKUP FUNCTION To activate the backup function of the system remove the Battery Insulation Tag from the backup battery compartment Replacing the Lithium Battery 1 Remove the battery tray located on the back of the unit 2 Replace the exhausted CR2025 3V lithium battery with a 9 new one with the side facing upward 3 Slide the battery tray back into the unit orn Se IMPORTANT Be sure that the battery is installed correctly Wrong polarity may damage the unit and void the warranty Tilting the Speaker Body up or down The speaker body can be lifted up to face forward at about a 45 degree angle Press down on the two Release Buttons located on both sides of the main body to lay the speaker body down flat SETTING THE CURRENT TIME Current Time Setting When first plugged in the display will show 12 00 after power up The following example shows the procedure for setting the clock time to 8 20 AM 1 The dock display will show 12 00 when first plugged in nin LULU Press the MEMO SET button once 12H will appear and flash in the display 2 Press ke or gt i button once to
10. asonable care and necessary maintenance as outlined in the owner s manual 3 Warranty of all SPECTRA products applies to residential use only and is void when products are used in a nonresidential environment or installed outside the United States This warranty gives you specific legal rights and you may also have other rights which vary from state to state TO OBTAIN SERVICE please remove all batteries if any and pack the unit carefully and send it prepaid by insured parcel post or UPS to SPECTRA at the address shown below IF THE UNIT IS RETURNED WITHIN THE WARRANTY PERIOD shown above please include a proof of purchase dated cash register receipt so that we may establish your eligibility for warranty service and repair of the unit without cost Also include a note with a description explaining how the unit is defective A customer service representative may need to contact you regarding the status of your repair so include your name address phone number and e mail address to speed the process IF THE UNIT IS OUTSIDE THE WARRANTY PERIOD please include a check for 35 00 to cover the cost of repair handling and return postage All out of warranty returns must be sent prepaid It is recommended that you contact SPECTRA first at 1 800 777 5331 or by e mail at info spectraintl com for updated information on the unit requiring service In some cases the model you have may be discontinued and SPECTRA reserves the right to offer alternative o
11. ded DC 6V AA size UM 3 battery x 4 Not 12 included CR2025 x 1 Included for memory back up Dimension 6 7 8 W x 7 1 2 D x 1 7 8 H Inch 174 W x 190 D x 47 H mm Weight 1 32 Ib 0 6kg TUNER SECTION Frequency range FM 87 5 108MHz AM 530 1710 KHz AUDIO SECTION Power Output 2 x 1 5 W 10 THD per Channel Speaker impedance 4 ohms AUX input sensitivity 500 mV ACCESSORIES Instruction Manual 1 pc iPod dock adapter 1 kit Including nano 3 generation nano 4 generation and iPod touch 2 generation ad You can help protect the environment Please remember to respect the local regulations turn in any non working electrical equipment to E an authorized waste disposal centre iPod is a trademark of Apple Inc registered in the U S and other countries Made for iPod means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards Apple is not responsible for the operation of this devise or its compliance with safety and regulatory standards 90 DAY LIMITED WARRANTY AND SERVICE VALID IN THE U S A ONLY SPECTRA MERCHANDISING INTERNATIONAL INC warrants this uni
12. for AM or FM Fine tune the AM or FM broadcast station FM The broadcast station signal is weak Find another station or relocate the unit until the best reception is obtained AM The location of the built in antenna is not correct Remove your iPod and rotate the unit until the best reception is obtained AM or FM no sound Unit is not in RADIO function mode Press the FUNC Button repeatedly to select the RADIO mode Volume is at minimum Increase Volume level iPod iPod will not play Unit is not in iPod mode Press the FUNC Button to select iPod mode iPod is not inserted properly Re insert iPod again Alarm No Alarm Alarm is not activated Check that Alarm indicator DD or BV or E or B appears in the Display Incorrect Alarm time Make sure AM or PM is set correctly Abnormal Operation Clock iPod Radio or AUX IN not functioning Internal micro controller needs to be reset Remove all the batteries including backup battery CR2025 disconnect the AC adaptor and wait a few seconds for the built in micro controller to reset Abnormal or no display Internal micro controller needs to be reset Remove all the batteries including backup battery CR2025 disconnect the AC adaptor and wait a few seconds for the built in micro controller to reset SPECIFICATIONS GENERAL Power source DC 6V 2000mA AC adapter Inclu
13. ptions for repair or replacement SPECTRA MERCHANDISING INTERNATIONAL INC 4230 North Normandy Avenue Chicago IL60634 USA 1 800 777 5331 To register your product visit the link below on the website to enter your information http www spectraintl com wform htm Printed in China 172 G4010A1020 JEN 14
14. rwards and press down the adaptor To remove replace the iPod adapter 1 Gently remove your iPod upwards 2 Push the iPod adapter backwards and gently pull upwards DOCKING YOUR iPod 1 Press the POWER STANDBY Button to turn on the unit 2 Press the FUNC Button to select iPod mode 3 Select a suitable adaptor included or use the one that comes with your iPod and insert it into the docking bay Your iPod can now be inserted onto the docking connector by aligning the connector on the bottom of the iPod onto the connector in the docking bay Note Please be careful when seating your iPod onto the dock to avoid damaging the 30 pin connector in the iPod or the docking system 4 The iPod will start playing and charging automatically Note The iPod will only charge when the JiMS 182 is using the AC adaptor 5 Adjust the sound level by pressing the m Buttons on the JiMS 182 Note The volume level cannot be adjusted using the volume control on your iPod after being docked 6 Press the M4 or i Buttons to skip to the previous or next song 7 Press and hold the M4 or Buttons to fast backward or fast forward during playback 8 To remove the iPod from JiMS 182 press and hold the m1 Button for few seconds to switch off the iPod and then gently remove it from the docking connector 9 To turn JiMS 182 off press the POWER STANDBY Button again ALARM OPERATION Your JiMS 182 provides two different wakeup times
15. st places e Places subject to constant vibration PROTECT YOUR FURNITURE This system is equipped with non skid rubber feet to prevent the product from moving when you operate the controls These feet are made from non migrating rubber material specially formulated to avoid leaving any marks or stains on your furniture However certain types of oil based furniture polishes wood preservatives or cleaning sprays may cause the rubber feet to soften and leave marks or a rubber residue on the furniture To prevent any damage to your furniture we strongly recommend that you purchase small self adhesive felt pads available at hardware stores and home improvement centers everywhere and apply these pads to the bottom of the rubber feet before you place the product on fine wooden furniture LOCATION OF CONTROLS 1 POWER STANDBY Button 2 FUNCTION Button 3 MEMORY SET Button 1 4 ALARM1 M Button 2 5 ALARM2 M Button 3 6 SLEEP Button 4 7 iPod Connector 5 8 pei Button 6 9 BAND P ll Button 7 10 rea Button 11 LIGHT Button 12 l Button 13 DISPLAY 14 LAMP 15 Battery Compartment 16 Release Button 17 AUX IN Jack 18 DC Jack 19 Lithium Battery Compartment Display Segment Sr HY peer q a am amp D v sam oS J Vaud 5 M2 SETTING UP AND CONNECTING This Portable Docking System is designed to operate on 4 x 1 5V AA UM 3 bat
16. t Channel number will appear and the Program Indicator M will also appear and flash in the Display While the Program Indicator M is blinking repeatedly press the ALM 2 MEM or ALM 1 MEM Button to select the desired preset channel 6 While the Program Indicator M is blinking briefly press the MEMO SET button again to complete 7 Tune to another station and repeat steps 4 to 6 to store stations in other preset locations TO RECEIVE PRESET STATIONS PoON gt on 1 Press the POWER STANDBY button to turn the unit on 2 Press the PIl BAND button to select AM or FM band as desired 3 Briefly press the ALM 2 MEM or ALM 1 MEM Button to select the preset channels TIPS FOR BEST RECEPTION 1 Automatic tuning depends on the signal strength of the broadcasting station so weak stations are sometimes skipped Tune manually to find the weak stations With stronger broadcast stations the tuner may stop before it reaches the station frequency or optimum reception Tune manually for the best reception 2 The receiver has a built in bar antenna If AM reception is weak slightly rotating or re positioning the unit will usually improve the reception Please also remove the iPod from the docking bay as this will definitely improve the AM reception NOTE For best AM reception please completely unwrap the power adaptor cord and fully extend it keeping the adaptor as far from the radio as possible AUX OPERATION
17. t to be free from defective materials or factory workmanship for a period of 90 days from the date of original customer purchase and provided the product is utilized within the U S A This warranty is not assignable or transferable Our obligation under this warranty is the repair or replacement of the defective unit or any part thereof except batteries when it is returned to the SPECTRA Service Department accompanied by proof of the date of original consumer purchase such as a duplicated copy of a sales receipt You must pay all shipping charges required to ship the product to SPECTRA for warranty service If the product is repaired or replaced under warranty the return charges will be at SPECTRA s expense There are no other express warranties other than those stated herein 13 This warranty is valid only in accordance with the conditions set forth below 1 The warranty applies to the SPECTRA product only while a It remains in the possession of the original purchaser and proof of purchase is demonstrated b It has not been subjected to accident misuse abuse improper service usage outside the descriptions and warnings covered within the owner s manual or non SPECTRA approved modifications c Claims are made within the warranty period 2 This warranty does not cover damage or equipment failure caused by electrical wiring not in compliance with electrical codes or SPECTRA owner s manual specifications or failure to provide re
18. teries Not included or the included AC Adaptor A Lithium battery Included is also required for the backup of the clock A BATTERY OPERATION For outdoor or portable use install 4 brand new good quality alkaline type batteries Remove the battery doors on bottom of the cabinet 1 Check the polarities and install 4 AA size UM 3 batteries correctly 2 Replace the battery doors IMPORTANT i Be sure that the batteries are installed correctly Wrong polarity may damage the unit and void the warranty ii For indoor use we recommend you remove all batteries and use the included AC adaptor BATTERY CARE l Do not mix old and new batteries Il Do not mix alkaline standard carbon zinc or rechargeable nickel cadmium batteries IIl Replace the battery only with the same or equivalent type IV If the unit is not to be used for an extended period of time remove the battery Old or leaking battery can cause damage to the unit and may void the warranty V Do not dispose batteries in fire Batteries may leak or explode BATTERY REPLACEMENT The batteries are weak and need to be replaced when the sound becomes distorted the Lamp or the Display starts flashing You need to replace all the exhausted 3 batteries at the same time as soon as possible to avoid battery leakage B AC Adapior Operation Insert one end of the AC adaptor into the DC Jack on back of JiMS 182 2 Connect the AC plug of the AC adaptor to
Download Pdf Manuals
Related Search