Jensen CR560X User's Manual
Contents
1. Turn the key off then turn the key on again The radio should resume Test Power Wiring playing at the same station and volume If not make sure the yellow wire is connected properly Turn ignition switch on Press the Power button to turn the radio on The display should light and show the radio display If not check the electrical connection at the yellow and red wires K If equipped the power antenna should also operate If not check electrical connections to the dark blue wire Press DISP button to display the clock 4 DISP 1 Press DISP button for three seconds until display flashes Test Antenna Connection Press lt lt to change minutes gt gt to change hours iE Hold a tuning button for more than two seconds The radio should tune to a nearby station If not check antenna connection Press to increase volume until you can hear the radio playing 5588 CR560X_EIN p65 8 2 29 00 10 46 PM _ is T CR560X JENSEN Test Speaker Connections These tests make sure the speakers are connected right If speakers don t play at all both wires may not be connected If the wrong speaker plays you hear front speakers when you expect rear speakers make sure you connected the wires right Press SEL four times Hold the button until the display shows BA r 10 Only the right speakers should be playing If not check the wiring Make sure you conn2. Turn on for amps Ground D L Connect to ground terminal or clean unpainted metal part of chassis Memory Connect to battery or 12 volt power source that is always live The radio will not store time or station presets if this wire is not connected Accessory Connect to existing radio wire or radio fuse The radio will not work if this wire j l l l is not connected LF LF ft RF RF O gray black Fuses while TE When replacing a fuse make sure new fuse LF RF is correct type and amperage Using an LR RR incorrect fuse could damage radio The green black _ violet black CR560X uses two fuses with in line fuse holders as part of rear wiring harness violet e 5 amp fast blow AGC yellow wire one e 5 amp fast blow AGC red wire Go to Testing on page 8 5588 CR560X_EIN p65 T 2 29 00 10 46 PM j ET E JENSEN CR560X Testing Before you finish the installation you should do the following tests to make sure the wiring is correct and everything is operating properly Reconnect Battery Test Memory Wiring 1 With the radio playing hold T button 1 for two seconds When wiring is complete reconnect the battery negative terminal CH 1 will appear on the display You just stored the current station in memory
3. BEE JENSEN How to Install the CR560X AM FM Stereo Radio Cassette Tape Player Install half sleeve page 5 Final Installation j page 10 lt 3 Connect and test radio pages 8 and 9 Welcome pages 6 and 7 What you re holding in your hands is no ordinary owner s manual We ve tried to make the instructions in this book clear and easy to follow For your Jensen stereo to work right it must be installed correctly This manual will show you how to install your new stereo like a pro It s a good idea to read all of these instructions before you begin the installation Most installations are straightforward and can be handled by a do it yourselfer with the right tools patience and the ability to follow instructions But do it yourself installation isn t for everyone If you still don t feel confident after reading this book consider turning the installation job over to someone better suited to it Warranty Service If your Jensen stereo should ever require service you will need to have the original dated receipt If you ever need to return the unit for any reason always include the receipt with the product Technical Assistance For technical assistance with the installation of the CR560X call 1 800 323 0221 5588 CR560X_EIN p65 Installation Contents Installation 0 0 0c ee 2 Before You Begin Installation 2 Tools and Supplies Needed 2 Speaker Requi
4. driver socket wrench set or other tools Radio removal tool e Electrical tape Advanced Installation e Soldering iron e Crimping tool e Volt meter or 12 volt test light e Solder e Crimp connectors e 14 18 gauge wire for power connections e Speaker wire Speaker Requirements Only connect the CR560X to speakers rated in the load impedance range of 4 to 8 ohms Speakers with a load impedance less than 4 ohms could damage the CR560X 5588 CR560X_EIN p65 2 Adapters for Easier Installation Electrical and dashboard adapters make installation easier Purchase adapters from your local Jensen retailer electronics store or car stereo specialty store Wiring Harness Adapter For a basic installation you can purchase a wiring harness adapter for your car s existing radio connectors This makes installation easy Dashboard Adapters The opening in your dashboard may not match the size of your Jensen radio Purchase an adapter kit for your car Antenna Adapter GM cars 1990 and newer GM cars have a small antenna connector You will need an adapter when installing this radio in a newer GM car 2 29 00 10 46 PM J BEE CR560X Professional Tip Connections Good wire connections are very important for best sound and long term reliability Here are two methods Splice 1 Strip 1 2 inch 12 mm of insulation from both wires 2 Wrap wires together 3 Fold wires over 4 Stretch electrica
5. CR560X_EIN p65 11 2 29 00 10 46 PM 5588 CR560X_EIN p65 12 Specifications FM Tuner TUNING TANGE sirieni vere amass aieneineteaere FM mono Sensitivity 2 0 0 eee eeeeseeeeeeeseeeeeeeeeeeeeereeeeeners 50 dB quieting sensitivity stereo eres Stereo separation 1 KHZ eceeeeeeeeeeeeeeeeeteeeeeeeeeteees AM Tuner TUNING FANG Oc ieisebie ck iaeciiieinis nee Re ae Amplifier Total system POWET oe ee ee cece etee eee tee eeeeeteeeteeeteeeees POWG6N QUU iii cccicctcccsccicasccsadcuasteiacedecdiesesecasaeesscnctessstkese ns Tape Frequency response ccccceeeeeeeeeeeeeeneeeeeaeeteeeeeteaeeeeaeeeee Wow amp FULL ccc ccccceeeseesssseaeeseeeeeececeeeeeessesstsseeeeees Channel separation 005 Signal to noise ratio a weighted General Power SUDDIY sessirnir aasre nisan Speaker output impedance FUSES derrr asavsads aa e e aai anaidai iai Specifications subject to change without notice E E E 100 Watts peak E EE E E front 2 x 25 Watts rear 2 x 25 Watt E aa E E E e AE A 50 Hz 14KHz PP RAI E E E E DEEA Ee A 15 JIS 35db 1 KHZ E T 55db Limited One Year Warranty USA and Canada Length of Warranty This warranty from Recoton Mobile Electronics shall be in effect for a period of one year from the date of the first consumer purchase Persons Protected This warranty will be enforceable by the original owner and any subsequent owners during the warranty period
6. so long as proof of date of purchase from an authorized Jensen dealer is presented whenever warranty service is required What is Covered Except as otherwise specified below this warranty covers all defects in material and workmanship in this product The following are not covered damage resulting from accident misuse abuse neglect product modification improper installation incorrect line voltage unauthorized repair or failure to follow instructions supplied with the product damage occurring during shipment claims must be presented to the carrier elimination of car static or other electrical interferences any product purchased outside USA or Canada or on which the serial number has been defaced modified or removed How You Can Get Service U S Purchasers Please telephone Jensen at 1 800 323 4815 We will either inform you of the name and address of an authorized Jensen repair station which will service the product or will advise you to send the product to a factory service center Canadian Purchasers The product should be returned to the Jensen dealer from whom it was purchased and such dealer either will service or arrange for service of the product If shipment of the product is required it should be packed securely The original dated bill of sale must always be included with the product as proof of warranty coverage What We Will Pay For We will pay for all labor and material expenses required to repair the p
7. ected the wires just like the chart on page 6 Press SEL four times again Hold the button until the display shows BA L 10 Only the left speakers should be playing If not check the wiring Make sure you connected the wires just like the chart on page 6 Press SEL five times Hold the button until the display shows FA F 10 Only the front speakers should be playing If not check the wiring Make sure you connected the wires just like the chart on page 6 Press SEL five times again Hold the button until the display shows FA r 10 Only the rear speakers should be playing If not check the wiring Make sure you connected the wires just like the chart on page 6 Once everything is operating correctly perform Final Installation on page 10 5588 CR560X_EIN p65 9 2 29 00 10 46 PM O ea T I i amp _ as T JENSEN CR560X Final Installation Slide radio chassis into half sleeve Secure to strap using nut Install faceplate by fitting left edge into position then pushing right edge closed Reinstall any items you removed from the dashboard Nut pplied Final Installation ISO DIN Remove trim ring from front of radio Trim ring is not needed for this type of installation Mount factory brackets on new radio using existing screws from old radio Slide radio and frame into dash opening and secure Install dash panels previously removed Install faceplate by f
8. ers will fit into your car without cutting or drilling You can also add an amplified graphic equalizer to tailor the sound to your liking INCREDIBLE Sound Jensen offers a full line of amplifiers high power speakers and subwoofers that can turn your car into audio dynamite You can go loud louder and loudest by selecting Jensen components from your retailer 2 29 00 10 46 PM iP e sae JENSEN CR560X Disconnect Battery Before you begin always disconnect the battery negative terminal Remove Old Radio Your original car radio is installed in one of four ways depending on the car Bracket Mounted Removal Tool Remove dashboard faceplate Some cars use a special removal tool Unscrew brackets to release the radio Disconnect wiring harness and 1 Insert the tool s remove radio 2 Pull out the radio 3 Disconnect wiring harness and remove radio Replacing an Aftermarket Radio ISO DIN Use a screwdriver to bend tabs completely out Remove trim to expose DIN chassis of the way Pull sleeve from dashboard The Remove the ISO DIN frame from the sleeve should fit tightly and may be damaged dashboard Unless VOU emneve Meararuihg Unscrew screws from the sides Disconnect wiring harness and remove radio 2 Pull Sleeve Out Caution Edges are sharp Use a rag or wear a glove 5588 CR560X_EIN p65 4 2 29 00 10 46 PM CR560X Install Half sleeve JENSEN Not needed for ISO DIN Japanese veh
9. icle installation Support Strap supplied Half sleeve supplied Adapter optional 1 Install adapter if necessary Install half sleeve into adapter from front of dash It will be a tight fit W Wiring Important If wiring connections are made wrong the unit will not operate properly and it could be damaged Follow the installation instructions carefully or have the installation handled by an experienced technician 5588 CR560X_EIN p65 5 Bend over tabs where possible to secure half sleeve to adapter or inside of dash Install strap to strut under dash Secure strap to an existing screw Professional Tip Fuse Adapters No convenient power wire Install a fuse adapter having a spade connector Fuse ie Fus KS Adaptor Crimp on a matching connector and attach e Yellow wire Fuse marked MAIN BAT or PWR e Red wire Fuse marked ACCY accessory or RADIO 2 29 00 10 46 PM T e JENSEN Wiring with a Wiring Adapter CR560X This is the easiest wiring method because it replaces your existing radio You will have to buy a wire harness adapter from your dealer a car stereo installation shop or electronics store If you use a wiring adapter you can connect all wires to the radio before you even start to take your old radio out Connect Wires Install Wiring Inside the Car Splice crimp or solder the wires from the Jensen connector to the wiring adapter Match the wire
10. itting left edge into position then pushing right edge closed 10 5588 CR560X_EIN p65 10 2 29 00 10 46 PM dl _ oe fs EENE CR560X JENSEN Troubleshooting Problem Cause Corrective Action Does not operate radio No power to red wire 12V with Check connection does not light key on Check vehicle fuse Inline fuse blown Replace fuse No speakers operate Speaker wires not connected Connect speaker wires radio lights normally Not all speakers operate Incorrect splices or connections Check all splices and connections Speaker wires shorting to chassis Check splices insulate all bare wires ground or to each other Blows fuses Power wire shorting to ground Insulate wire Speaker wires shorting to ground Insulate wire Incorrect fuse Install fuse of correct rating Can t find cause of problem Call Jensen Technical Assistance 1 800 323 0221 Removing Radio from Dash Professional Tip Securing Wires Be proud of your installation Use wire ties to bundle wires together when possible But never bundle speaker wires and power wires together Secure loose wires to the car to make sure they don t rub or rattle Removal Key 1 Remove faceplate 2 Remove trim ring by gently pulling up on the middle of the trimming to release the plastic snaps Insert removal keys between radio and dash trim to depress locking springs Pull radio out of dash 11 5588
11. l tape tightly over splice Splice k Brip Wire _ Me tema Solder Rosin core solder Soldering iron Solder Solder is the best way to connect wires but it takes skill and practice Splice the wires as shown above Before taping heat the wires not the solder When the wires are hot enough touch the solder to the splice The solder will flow over the wires Stretch electrical tape tightly over splice Important Be very careful when soldering wires in your car Cover nearby carpeting and seats to prevent damage from hot solder 5588 CR560X_EIN p65 3 JENSEN Professional Tip Crimp Connections Purchase crimp connectors and crimping tool Connectors are color coded This Jensen radio uses RED connectors 18 20 gauge wire 1 Strip 1 4 inch 6mm of insulation from both wires 2 Insert into connector 3 Crimp tightly You can make permanent splices using butt connectors or select connectors that can be removed and reinstalled ae OF Strip Wire 7 1 4 6mm i Professional Tip Upgrading Your System International Jensen makes a wide range of car stereo products that will make your car system sound better great or INCREDIBLE Better Sound Install a Jensen tape deck or CD player like you re doing now High power units can make your existing speakers sound better and play louder Great Sound Replace your existing speakers with Jensen speakers Many of our speak
12. rements 2 Adapters for Easier Installation sicn 2 e CONNECTIONS ceceeeeeeeettetetteeteeee 3 e Crimp CONNECTIONS ccceeeeee 3 e Upgrading your System 3 Disconnect Battery 0 00 4 Remove Old Radio cee 4 Install Half sleeve eeeeeeee 5 Wiring 5 e Fuse Adapters sssoosnenenennee 5 e Cars with a Single Speaker Wire ceccceeceeeeeeseees 5 Wiring with a Wiring Adapter 6 Connect Wires ssec 6 Install Wiring Inside the Car 6 Wiring Diagram Advanced Installation s csicccssteeevacaeetcneens 7 Testing oinin 8 Reconnect Battery 0 0 0 8 Test Power Wiring 8 Test Antenna Connection 8 Test Memory Wiring seses 8 Set the Clock n se 8 Test Speaker Connections 9 Final Installation 00 cceeeeee 10 Final Installation ISO DIN 10 Troubleshooting 11 Removing Radio from Dash 11 e Securing Wires ccceeeteeee 11 Specifications and Warranty ssssssssssnsnnnnnnnn 12 2 29 00 10 46 PM BEE JENSEN Installation CR560X Before You Begin Installation Before you begin you will need tools supplies and adapters It is best to make sure you have everything you need before you take your dashboard apart Tools and Supplies Needed Basic Installation e Flat and Phillips screwdrivers e Wire cutter e Wire stripper e Tools to remove existing radio screw
13. roduct but you must pay any labor costs for the removal and or installation of the product If the product is shipped for warranty service you must prepay the initial shipping charges but Jensen will pay the return shipping charges if the product is returned to an address inside the USA or Canada Limitation of Implied or Statutory Warranties and Conditions All implied or statutory warranties and condi tions including warranties or conditions of merchantability fitness for particular purposes and non infringement are limited in duration to the length of this warranty Exclusion of Certain Damages Jensen s liability is limited to the repair or replacement at our option of any defective product and shall not include incidental or consequential economic damages of any kind Some states and or provinces do not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state and province to province JENSEN Recoton Mobile Electronics A Division of Recoton Audio Corporation A RECOTON COMPANY 1090 Emma Oaks Trail Lake Mary Florida 32746 2000 Recoton Audio Corporation 2 29 00 10 46 PM
14. s according to the chart below and the wiring adapter instructions Splices You can make all these connections without even being Y 77 in the car Wiring Adapter attach to car wiring harness Wiring Color Codes LF Speaker white black LF Speaker white LR Speaker green black LR Speaker green RF Speaker gray black RF Speaker gray RR Speaker violet black RR Speaker violet Power Antenna dark blue Ground black Ignition red Battery yellow 5588 CR560X_EIN p65 6 Connect wiring adapter to the car s existing wiring harness Connect antenna extender cable to car antenna lead Slide radio part way into half sleeve Extender Cable Go to Testing on page 8 2 29 00 10 46 PM T e EOE EENE CR560X JENSEN Wiring Diagram Advanced Installation If you are installing new speakers or amplifiers or replacing an aftermarket installation use this diagram Back of Radio Antenna Jack HHHH RCA to RCA cables Amplifier wiring not supplied See amplifier instructions O Power Antenna Connect to power antenna or ampli Dark Blue K _ fier If not used tape bare end of wire
Download Pdf Manuals
Related Search