Jasco RM24950 User's Manual
Contents
1. find a code that works for your product Please refer to Programming with Code Search on page 8 for more information on using the code search feature to learn how to search through the library of codes for your products NOTE You can store any kind of code under any mode except TV I E you can store a VCR code under the CBL button or a DVD code under the VCR button etc However you can only store TV codes under the TV button Direct Code Entry 1 Press and hold the SETUP button until the red indicator stays on then release the SETUP button 2 Press and release the desired mode button TV VCR etc The red indicator blinks then stays lit 3 Enter the 4 digit code from the code tables on separate sheet Note after a valid code entry the red indicator turns off For an invalid code the red indicator flashes 4 With your device on press CHANNEL UP If the device responds no further programming is required Note If some buttons do not operate your equipment try one of the other codes for your brand Write your codes down here for easy reference later SAT CBL Audio AUX Code Search If your product does not respond after you have tried all the codes for your brand or if your brand is not listed try searching for your code by following these steps Oo O Ss SS 1 Manually turn on the device TV VCR etc to be controlled 2 Press and hold the SETUP button until the red indicator stays2. for all Modes Note this feature is not supported by all codes VCR DVD DVR Punch Through Feature This remote allows the 6 VCR transport buttons i e PLAY PAUSE STOP FF REWIND and REC to Punch Through control from any Mode programmed with TV SAT or Cable codes to the last VCR DVD or DVR programmed Mode you used Normally other types of remotes only punch through from another Mode on the 6 VCR buttons to the device programmed under the VCR Mode button This is not much use if you are using a DVD programmed under a Mode other than VCR For example if you have 3 DVD VCR or DVR devices programmed into this remote the last one you accessed on the remote will be the one that has control of the 6 VCR transport buttons when in any other Mode This feature will not operate if the programmed TV SAT or Cable code has its own VCR transport button control e g a TV Combo SAT PVR etc Volume Mute Control and Punch Through Feature This remote lets you select which device Mode controls your Volume Mute buttons The remote is initially set factory default for all device Modes programmed with Visual codes e g TV VCR DVD DVR SAT amp CABLE and Audio codes e g CD amp AUDIO to use their own Volume Mute control if present If the programmed Visual code has no Volume Mute operation of its own then those buttons will punch through control to the TV Mode device without needing to change to TV Mode Please refer t
3. on then release the SETUP button 3 Press and quickly release the desired mode button TV VCR etc The red indicator blinks off once 4 Press the CHANNEL UP button repeatedly up to 300 times until the device to be controlled changes channel The red indicator blinks off with each button press If you accidentally overshoot the code required press the CHANNEL DOWN button to backtrack through the library until the device changes channel Pressing CHANNEL UP changes direction to forward again 5 Press and release ENTER to install the code Code Search cont Most users will store VCR codes under the VCR button Cable codes under CABLE etc If for example you want to store a VCR code under CABLE first follow the procedure for Direct Code Entry previous page and press CABLE in step 2 of Direct Code Entry then enter ANY VCR code in step 3 of Direct Code Entry Then follow the steps for Code Search on the previous page Note Ifthe device does not have a CHANNEL UP button use PLAY VCR only or ON OFF instead Code Search starts from the currently stored 4 digit number under that mode Code Identification Feature The Code Identification Feature allows you to identify the three digit library code stored under your device key For example if you want to find out what 4 digit code is stored under your TV device key follow the six steps below 1 Press and hold the SETUP button until the red indicator stays on Release th
4. 24950 Universal Remote Instruction Manual SLEEP PREV CH ED G2 3 _ EN Sei 6 zE _3_ 9 cca sce vcr Table of Contents TNO THON PRA RA AR PRE RO ROTA 3 Button Euftiions cain 4 SUR RS A 6 Battery Installation cs ccccsecsedncessnccanactsnedesesvacss 6 Battery Save aio 7 Co aaa 7 PowerDndenulti orc 7 Cia 7 Code EMY lane 8 Direct Code Entry sccscccsacncaseatnnadesconnesbatwvndie 8 Code Searc M RR scp RR 8 Code Identification Feature 9 Programming Combo Device Codes 10 Controlling Combo Devices 10 Controlling Devices with Power On and Off 10 VCR DVD DVR Punch Through Feature 11 Volume Mute Control Feature 11 Setting Volume Mute Control Punch Through 12 Setting any Mode to use its own Volume Mute 12 Sela 13 Colella 14 Tipson Learning rr 14 IR Transmitter Finder feature 16 Learning Commands cscssesasadanncseacivanceaceoes 16 Clearing Commands s cccecssscssesccrescesnseenscaonnnsnss 18 Clearing Learned commands for a mode 18 Meola 18 Troubleshooting ricada 19 2 Introduction Congratulations on your purchase of this 24950 Universal Remote Control It is one of the most unique looking and easy to use remote controls available today With the 24950 juggling multiple remote controls is a thing of the past Your 24950 Universal Remote controls up to 5 devices includin
5. TE button until the red indicator blinks off then release the button 3 Press and release the desired Mode button TV VCR etc the red indicator blinks then stays on 4 Press and release the VOLUME Down button the red indicator blinks then stays on 5 Press and release the MUTE button and the red indicator turns off 6 All Visual and Audio programmed Modes will now punch through to the respective Modes you have chosen for Volume Mute control 12 Sleep Timer The SLEEP button enables the remote to turn off your TV after a period of 1 to 99 minutes as shown below The remote must be in TV mode to set a Sleep Timer This feature works even if your TV does not have a sleep feature 1 Press and release the TV device button 2 Press and hold the SLEEP button until the red indicator remains lit about 2 3 seconds 3 Release the SLEEP button 4 Press and release the numeric buttons 01 99 for the time required The red indicator will blink off to indicate button press acceptance 5 TV Sleep Timer is set 6 Leave the Remote pointing towards the TV with an unobstructed path To cancel the Sleep Timer press and hold the SLEEP button until the red indicator blinks or press and release the ON OFF button in TV mode 13 Code Learning The learning feature lets you learn functions from your original remote control For example you may want to use your remote to operate the RANDOM PLAY feat
6. arning is now complete Line up your remotes that you re learning from in front of the Learning remote on a hard surface approx 1 inch apart Clearing Commands To Clear all Learned Commands under a mode Clearing learned commands is helpful if for example you replace your CD player with another brand or model If you had learned a feature from your old CD player s original remote on to this remote such as RANDOM PLAY that feature would no longer work for your new CD player Should you wish to remove or clear one or more learned commands follow the steps below 1 Press and hold the SETUP button until the red indicator turns on Release the SETUP button 2 Press and release the button for the mode you want to clear TV VCR etc The red indicator blinks off 3 Press andrelease the LEARN button TWICE The red indicator blinks off 4 Press andrelease the SETUP button The red indicator turns off All learned Commands under that mode are now cleared Master Clear To Clear all Learned Commands under all modes 1 Press and hold the SETUP button until the red indicator turns on Release the SETUP button 2 Press and release the LEARN button TWICE The red indicator blinks off 3 Press and release the SETUP button The red indicator turns off All Learned commands in the remote are now cleared Lost Your Codes Enclosed with this remote is a sticker on which you should write the codes
7. e SETUP button 2 Press and release the desired mode button TV VCR etc The red indicator blinks then stays lit 3 Press and release the SETUP button The red indicator blinks off 4 To find the first digit for the code stored under the mode key pressed in step 2 press each numeric key from 0 9 in turn When the red indicator blinks off the number you pressed is the first digit for the code you are searching for 5 To find the second digit repeat step 4 this time when the red indicator blinks off this is the second digit 6 Repeat step 4 to find the third and fourth digits Programming Combo Device Codes Some Combo devices e g TV VCR TV DVD DVD VCR etc will require you to set up two different Mode buttons to control both parts of the Combo device For example if you have a TV DVD Combo you might need to set up one code under the TV button to control the TV part AND a separate code under any other Mode button to control the DVD part Controlling Combo Devices Some Combo devices e g TV VCR TV DVD DVD VCR etc have separate buttons on the original remote to select the part of the Combo device to be controlled For example if your Combo device is a DVD VCR then its original remote might have separate DVD and VCR buttons for selection of the Combo part you would control The equivalent button functions can be found on your new remote by using the device Mode and SETUP buttons Referring to Programm
8. erate the TV Also operates DVD Scan 18 GUIDE Displays satellite or cable on screen program guide 19 TV VCR Operates the same as the TV VCR or antenna keys on your original remotes 20 PREV CH Returns to the previously selected channel or DVD repeat toggle 21 SLEEP Turns off the TV after a period of 1 to 99 minutes 22 MUTE Turns off the TV sound while the picture remains 23 Red Indicator Lights when any button is pressed 24 SETUP Used for setting up your remote se Battery Installation 1 On the back of the remote push down on the tab and lift the cover off 2 Match the batteries to the and marks inside the battery case then insert 2 AAA alkaline batteries 3 Press the battery cover back into place Battery Saver Your remote automatically turns off if the buttons are depressed more than 30 seconds This will save your batteries should your remote get stuck in a place where the buttons remain depressed e g between the sofa cushions Code Saver Codes are stored in permanent memory while you are changing batteries so you will not lose any codes stored in the remote while you are changing batteries Power On Default The remote powers on in TV mode Code Setup The SETUP button is used to setup the remote You can either setup the remote using the code for your brand of product from the code tables on separate sheet or you can search through the library of codes until you
9. features that exist on your product E G your product must have PREV CH ability for the PREV CH button to operate this feature 4 Button Functions cont 1 ON OFF Turns device On or Off TV VCR DVD SAT CBL AUDIO AUX Selects product to be operated 3 CHANNEL UP DOWN Changes the channels Also controls DVD CD CHAPTER track selection i e DVD CD Track Skip Up Down Note the VCR buttons also control DVD when in DVD Mode 4 VOLUME UP DOWN Changes the volume level of the product normally the TV 5 INPUT Selects the video inputs of your TV if equipped with that feature 6 NUMBERS Enter numbers for direct channel selection Some products require Enter to be pressed after channel selection 7 ENTER Used after direct channel number entry to immediately change to the selected channel D 9 INFO Displays on screen channel information etc OK Selects menu items for the device you are controlling 10 MENU brings up the DVD disc Menu screen Use with the UP DOWN LEFT amp RIGHT navigation buttons 11 LEARN Used to setup learning functions 12 PIP TV Picture in Picture control 13 SWAP Swaps TV PIP screens 14 MOVE Moves the position of the PIP screen 15 EXIT Exits On Screen Menus and or Returns to previous On Screen selection 16 UP DOWN LEFT amp RIGHT Navigation buttons 17 RECORD PLAY STOP REW FF PAUSE VCR control buttons operate your VCR even when the remote is set to op
10. for each device you programmed Apply the sticker to the back of the remote or somewhere convenient for future reference Also on the sticker is our website address which should you lose your codes or programming instructions you can find available on our website www jascoproducts com 18 Troubleshooting Remote does not operate your product e Press the mode button of the product you want to control e Program the remote with a new code e Install new batteries You might have to reprogram your remote after installing new batteries e Remote may not be compatible with your product Remote does not operate some features of your product e Program remote with a new code e Remote may not be able to operate all features of your product or button names might be different than your product Red Indicator blinks after you program a product code e Remote did not accept the code e Try to program the code again or try a different code 90 Day Limited Warranty Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit This warranty is in lieu of all other warranties express or implied Some states do not allow limitations on how long an implied
11. g the most popular brands of TV VCR DVD SAT CBL and audio equipment Note Some functions from your original remote may not be controlled by the 24950 remote Use the original remote if available to control such functions Sometimes buttons other than described in these instructions may actually perform the function For example the CHAN and VOL buttons might be used to navigate through menu choices We recommend you experiment with the remote to identify if such situations pertain to your equipment The 24950 Universal Remote is easy to use easy to program and it gives you total control at the touch of your fingertips Button Functions 1 24 ON OFF SETUP I O 2 th S 23 A ZAN a o x CH y E 22 3 vol VOL A CH 4 No Ya Na De Da INPUT SLEEP PREV CH 20 1 Ji 2 JL 3 ce 6 5 19 7 C8 C9 AT 0 TV VCR ENTER 7 Sais 11 14 Universal 12 13 Note The Record button must be pressed TWICE to record from your VCR For some brands of VCRs you might need to press the Record button once then press it again for three seconds Some buttons on the remote might have functions that are referred to by different names on the device you are controlling E G PREV CH may be called RECALL or ENTER may be called DISPLAY These differences depend on the brand and model of your product Also this remote can only operate
12. ifferent clear Mode If it learns okay then it is likely to be a different code type from the others and cannot be learned under the same Mode 15 IR Transmitter Finder Feature This feature assists you in identifying where your original remotes IR transmitter is located and is particularly useful if your original remote s IR transmitter is hidden behind a lens 1 Point both remotes facing each other by approximately inch apart see Tips on Learning on previous pages 2 Press and hold the SETUP button until the red indicator turns on then release the button 3 Press and release the desired Mode button TV VCR etc the red indicator blinks then stays on 4 Press and release the LEARN button the red indicator blinks then stays on 5 Press and hold any Original Remote button and move the Original Remote to the left and right and or up and down in front of the Learning remote IR transmitter The red indicator will remain on if no IR from the Original remote is found and the red indicator will blink on and off more rapidly when the IR transmitters are lining up The point where the red indicator blinks most rapidly is where the two IR transmitters are aligned Note some original remotes will only transmit IR on the initial button press then stop In these cases quickly press and release the original remote button repeatedly during this procedure 6 You can now learn a button from your original remote by continuing fr
13. ing cont h Keep the distance between the two remotes to approximately 1 inch and do not move or change the distance between the two remotes until you have learned all the required buttons for that Mode i When Learning do not release the button being Learned until the red indicator has blinked off for half a second j Avoid learning your original remote Volume Mute buttons unless you are sure these operate the same device e g some original DVD remotes include TV Volume Mute button control and can be two different types of code k Avoid learning your original remote VCR transport buttons unless you are sure these operate the same device e g some original TV remotes include VCR button control and can be two different types of code I Iflearning the first or second buttons for a Mode results in continuous errors then try the following i End the Learn session by pressing the SETUP key ii Clear out the learned commands for that Mode iii Check the IR transmitters are correctly aligned between the two remotes use the IR Transmitter Finder facility iv Adjust the distance between the two remotes to be closer e g half an inch or a bit further away e g 2 inches from each other v Try learning the original remote for that Mode again If problems reoccur with the same button check the original remote button being learned does it transmit Does it operate the target device Try learning that button under a d
14. ing with Code Search on page 8 setup a device Mode e g DVD with the correct code for your Combo device Assuming the DVD VCR Combo device is the example and its code is programmed under DVD Mode press and hold the DVD Mode button for more than one second to send the DVD button command To send the VCR button command quickly press and release the SETUP button followed by pressing and releasing the DVD Mode button This method can be applied similarly to all Combo devices e g TV VCR TV DVD DVD VCR etc and is available for all Modes Note this feature is not supported by all codes Controlling Devices Requiring Separate Power On and Off Buttons Some devices e g certain RCA TVs require separate Power On and Power Off buttons to turn the device on and off The equivalent button functions can be found on your new remote by using the device Mode and ON OFF buttons Referring to Programming with Code Search on page 8 setup a device Mode e g TV with the correct code for your device Assuming a TV device is the example and its code is programmed under TV Mode to turn your TV on press and hold the TV Mode button for more than one second to transmit the Power On button command 10 Controlling Devices Requiring Separate Power On and Off Buttons cont To turn the TV off press and release the ON OFF button to transmit the Power Off button command This method can be applied similarly to any device and is available
15. o the next page for more information 11 Any Mode chosen for Volume Mute control MUST have its own Volume Mute function or the Volume Mute buttons will do nothing Setting ALL Volume Mute Control to any one Mode This routine can set all Modes to punch through to any one chosen Mode for Volume Mute button control without the needing to change to that Mode 1 Press and hold the SETUP button until the red indicator turns on then release the button 2 Press and hold the MUTE button until the red indicator blinks off then release the button 3 Press and release the desired Mode button TV VCR etc for Volume Mute control the red indicator blinks then stays on 4 Press and release the MUTE button and the red indicator turns off The red indicator will blink rapidly for three seconds if the Mode you have selected has no Volume Mute control 5 All other Modes will now punch through to your chosen Mode for Volume Mute control 6 All Visual and Audio programmed Modes will now punch through to the respective Modes you have chosen for Volume Mute control Setting any Mode to use its own Volume Mute Control This routine can set any Mode to use only its own Volume Mute control Note If your chosen Mode has no Volume Mute functions of its own then the Volume Mute buttons will do nothing 1 Press and hold the SETUP button until the red indicator turns on then release the button 2 Press and hold the MU
16. om Step 4 in the Learning Commands section on the next page or to exit at this point press and release the SETUP button Learning Commands The learning feature allows you to learn functions from your original remote control For example you may want to use your remote to operate the RANDOM PLAY feature from your original CD remote control This remote is equipped with an easy learning feature that allows you to learn features such as RANDOM PLAY from your original CD remote by following the steps below and on the next page 1 Press and hold the SETUP button until the red indicator turns on then release the button 2 Press and release the desired mode button TV VCR etc the red indicator blinks then stays on 16 Learning Commands cont 3 Press and release the LEARN button the red indicator blinks then stays on 4 Press and release the Learning Remote button that you want to teach e g ON OFF 5 Point your existing remote at the learning Remote approximately 1 inch apart see tips on previous pages 6 Press and hold the Original Remote button e g On OFF until the red indicator blinks once and stays on If there is a learning problem the red indicator blinks for three seconds and stays on If this happens repeat Steps 4 to 6 7 Repeat Steps 4 6 for other buttons you want to learn 8 Press andrelease the SETUP button when all desired remote commands are learned Code Le
17. ure from your original CD remote control This remote is equipped with an easy learning feature that lets you learn features such as RANDOM PLAY from your original CD remote Tips On Learning You can only learn one device type under any one Mode button e g only learn TV codes under the TV Mode VCR codes under the VCR Mode etc If you are trying to learn from a Universal remote it might have more than one code type stored under a Mode Try learning from another remote to see if there s a problem with the type or brand of remote you are trying to learn from a Some functions from some types of remotes might not be able to be learned b No functions may be stored under the LEARN or SETUP buttons c Only one original device type can be learned per individual Mode d Use fresh batteries for both the Learning Remote and the Original Remote e Keep at least three feet away from incandescent or low energy lights when learning f Perform a Master Clear see page 18 before learning and try learning 2 or 3 commands initially Then carry out a Master Clear before completely learning your original remote s commands g Point your existing remote at the bottom of the learning Remote so the IR transmitter sensor on both remotes are directly in line with each other You may need to adjust the height of either remote to achieve this Use the IR Transmitter Finder feature to assist you 14 Tips On Learn
18. warranty lasts or permit the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific rights and you may also have other rights which vary from state to state If unit should prove defective within the warranty period return prepaid with dated proof of purchase to Jasco Products Company 311 N W 122nd Oklahoma City OK 73114 19 24950 Universal Remote Instruction Manual Jasco Products Company 311 N W 122nd Oklahoma City OK 73114 Made in China 24950 06 07
Download Pdf Manuals
Related Search