InFocus SP-CEIL-UNIV User's Manual
Contents
1. Installation and Assembly All in one Projector Adapter Plate for Model SP CEIL UNIV InFocus Projectors cus eer Maximum Load Capacity 25 Ib 11 kg by a qualified professional installer Read instruction sheet before you start installation and assembly A WARNING e Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard ware and components IMPORTANT Turn to the appropriate page for your ceiling installation Applications Flush Mount Extension Column Lightweight Suspended Ceiling Plate Installations To Wood Joist Finished Ceilings Exposed Wood Joists or Wood Beam Ceilings To Concrete Ceilings 1 of 11 ISSUED 10 22 04 SHEET 055 9236 5 01 10 06 Visit the InFocus Web Site at www infocus com Before you start check the parts list to insure all of the parts shown are included Parts List Description Qty Part Number 055 0420 560 9646 520 1151 520 1196 540 9440 5S1 015 C03 590 0097 510 1087 510 1079 590 2020 590 1030 590 1050 520 1164 520 1187 510 1050 510 1059 580 1042 055 1539 055 1540 projector mount assembly 4mm security allen wrench 10 32 x 3 8 serrated socket pin screw 10 32 x 1 4 socket pin screw 1 4 flat washer 14 x 2 5 phillips hex head wood screw concrete anchor M4 x 16 mm serrated socket pin screw M4 x 12 mm serrated socket pin screw 198 x 313 x 375 retaining spacer 198 x 313 x 187 retaining2. bracket N After repeating step one tighten all fasteners CUTAWAY VIEW 4of 11 ISSUED 10 22 04 SHEET 055 9236 5 01 10 06 Visit the InFocus Web Site at www infocus com Flush Mount Installation Drill two 5 32 4 mm dia holes to a minimum depth of 2 5 64 mm Attach projector mount assembly A with two 14 x 2 5 6 mm x 65 mm wood screws F and two flat washers E as shown in figure 1 or figure 2 depending on joist orientation Tighten wood screws F using 3 8 10 mm socket wrench until projector mount assembly A is firmly attached A WARNING e Tighten wood screws so that projector mount assem bly is firmly attached but do not overtighten Overtight ening can damage the screws greatly reducing their holding power e Never tighten in excess of 80 in Ib 9 N M e Make sure that mounting screws are anchored into the center of the joist The use of an edge to edge stud finder is highly recommended Skip to step 7 WOOD JOIST a WOOD JOIST ee a FRONTOF SN f ZO SSN FRONTOF N N N VIZNI S P wo ae ae N KN A A ii Ng LA in gee a pe we NN ly lt XQ et lt 2 1 amp i Sl 3 r w a f O l bee Pa Ce E a A l E l j i f i i E f F E T amp figure 1 figure 2 5 of 11 ISSUED 10 22 04 SHEET 055 9236 5 01 10 06 Visit
3. wood screws F or locknuts for threaded rods until projector mount can be rotated Rotate mount to desired position and retighten screws or locknuts To adjust yaw swivel for extension column applications Loosen screw on projector mount assembly A indicated below until projector mount can be rotated Rotate mount to desired position and retighten screw To adjust pitch forward and backward tilt Loosen two screws on projector mount assembly A indicated below Tilt mount to desired position and retighten screws To adjust roll side to side tilt Loosen two screws on projector mount assembly A indicated below Tilt mount to desired position and retighten screws SCREW FOR SWIVEL STOP SCREWS FOR PITCH _ ADJUSTMENT gt lt lt BACK OF MOUNT 11 of 11 ISSUED 10 22 04 SHEET 055 9236 5 01 10 06 Visit the InFocus Web Site at www infocus com
4. the InFocus Web Site at www infocus com Installation to Extension Column SP EXTARM O1 SP EXTARM 02 SP EXTARM 03 SP EXTARM 04 a Screw extension column sold separately to ceiling plate Q Align the notch with one of the four holes in the ceiling plate Q and secure extension column with a M5 x 10 mm socket pin screw M using security allen wrench B See detail 3 Screw projector mount assembly A onto the extension column as shown in detail 4 EXTENSION COLUMN SOLD SEPARATELY Note For 3 4 extension columns reducer ULLISTED ACC 913 will be required as shown in detail 5 Tighten swivel stop screw against extension column or reducer using security allen wrench B Note Swivel stop screw is used to jam against ra threads of extension column or reducer to prevent any excess movement of projector mount assembly A Do not overtighten screw DETAIL 3 overtightening screw will damage threads making it difficult to separate products Note Slotted set screws N are used to jam against the threads of each connecting joint to prevent any excess movement Do not overtighten screws overtightening screws will damage A threads making it difficult to separate the products Skip to step 7 SWIVELSTOPSCREW S BACK OF MOUNT DETAIL 4 eae 3 4 EXTENSION COLUMN ACC 913 NOT UL LISTED BACK OF SWIVEL STOP SCREW DETAIL 5 6 of 11 ISSUED 10 22 04 SHEET 055 9236 5 01 10 06 Visit the In
5. 4 EXTENSION COLUMN ACC 913 NOT UL LISTED A BACK OF MOUNT SWIVEL STOP SCREW Visit the InFocus Web Site at www infocus com 7 of 11 ISSUED 10 22 04 SHEET 055 9236 5 01 10 06 Note The projector adapter plate and projector you are installing may differ in appearance from the sample illustrated below Align shoulder on connection block opposite of front of projector Attach adapter plate R to connection block from projector mount assembly A using two 10 32 x 3 8 serrated socket pin screws C as shown CONNECTION BLOCK SHOULDER ADAPTER PLATE SS FRONT OF ee PROJECTOR Attach extension brackets S to adapter plate R using two M4 x 6 mm serrated socket pin screws P For specific models see step 8H 8 of 11 ISSUED 10 22 04 SHEET 055 9236 5 01 10 06 Visit the InFocus Web Site at www infocus com Flip projector upside down Find your projector from the models listed below Using the holes indicated on the corre sponding hole pattern diagram attach adapter plate R to projector using three M4 x 16 mm serrated socket pin screws H and three 198 x 313 x 375 retaining spacers J Notes Retaining spacers go between adapter plate and projector Front of projector Projectors using hole pattern G use one M4 x 12 mm screw I and one 198 x 313 x 187 retaining spacer K where indicated Using holes indicated in hole pattern H attach adapter plate R to proje
6. Focus Web Site at www infocus com Installation to Lightweight Suspended Ceiling Plate EXT LTMT PLTB O Refer to instruction sheet for lightweight suspended ceiling plate sold separately for attachment of ceiling plate to ceiling Screw extension column sold separately to retaining collar in ceiling tray Align the notch with one of the four holes in retaining collar and secure extension column with a M5 x 10 mm socket pin screw M using security allen wrench B See detail 6 Screw projector mount assembly A onto the extension column as shown in detail 7 Note For 3 4 extension columns reducer ACC 913 will be required as shown in detail 8 Tighten swivel stop screw against extension column or reducer using security allen wrench B Note Swivel stop screw is used to jam against threads of extension column or reducer to prevent any excess movement of projector mount assembly A Do not overtighten screw overtightening screwwill damage threads making it difficult to separate products Note Slotted set screws N are used to jam against the threads of each connecting joint to prevent any excess movement Do notovertighten screws overtightening screws will damage threads making it difficult to separate the products Skip to step 7 LIGHTWEIGHT SUSPENDED CEILING PLATE SOLD SEPARATELY DETAIL 6 a EXTENSION COLUMN UL LISTED DETAIL 7 DETAIL 8 3
7. ctor using four M6 x 12 mm serrated socket pin screws O and four spacers L A C200 DP6500X LP650 SP5700 SP7200 SP7205 SP7210 B C40 C50 DP2000S DP2000X LP240 LP250 E C109 C110 DP8000 LP790 SP4800 SP4805 X1 X1a X2 X3 LP690 H C440 C450 C460 DP8400X DP8500X LP840 LP850 LP860 G C160 C180 LP540 LP640 SP5000 9 of 11 Visit the InFocus Web Site at www infocus com C LP340 LP350 LP500 LP530 SP110 o 0 FN e a MY y Q 0 0 l C410 C420 LP815 LP820 DP8200X oO c R oO ISSUED 10 22 04 SHEET 055 9236 5 01 10 06 J IN72 IN74 IN76 K IN24 IN26 Always use an assistant or mechanical lifting equipment to safely lift and position the projector assembly A as shown Tighten captive screw to secure one 10 32 x 1 4 socket pin screw D through projector to projector mount assembly A projector mount assembly A and into connection block as shown Slide connection block with projector into projector mount D IMPORTANT For security installations insert CONNECTION BLOCK FRONT OF MOUNT ete CAPTIVESCREW 10 of 11 ISSUED 10 22 04 SHEET 055 9236 5 01 10 06 Visit the InFocus Web Site at www infocus com Projector Alignment To adjust yaw swivel for wood stud concrete ceiling and threaded rod mounting applications Loosen
8. onal Cord Management N ceine S install two spacers L between ceiling plate Q and ceiling 3 of 11 ISSUED 10 22 04 SHEET 055 9236 5 01 10 06 Visit the InFocus Web Site at www infocus com Installation to Concrete Ceilings Alligator concrete anchors are recommended Drill two 1 4 6 mm dia holes to a minimum depth of 2 5 64 mm Attach ceiling plate Q using two concrete anchors G and 14 x 2 5 wood screws F as shown in Illustration A and 1 2 and 3 Tighten all fasteners Skip to step 7 A WARNING e Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components e Tighten concrete anchor bolt firmly but do not over tighten Overtightening can damage the bolt greatly reducing its holding power Illustration A e Never tighten in excess of 80 in Ib 9 N M A WARNING e Concrete anchors are not intended for attachment to concrete wall covered with a layer of plaster drywall or other finishing material If mounting to concrete wall covered with plaster drywall is unavoidable plaster drywall up to 5 8 thick must be counterbored as shown below If plaster drywall is thicker than 5 8 custom fasteners must be supplied by installer concrete ceiling INCORRECT AATE Gaon metal MA concrete Place ceiling plate over anchor and secure with screw
9. spacer 25 ID x 56 OD x 26 spacer M5 x 10 mm socket pin screw 10 32 x 3 16 slotted set screw M6 x 12 mm serrated socket pin screw M4 x 6 mm serrated socket pin screw ceiling plate adapter plate extension bracket Nh i Po BS gt I FO ee ON VS eS a A B Cc D E F G H l J K L M N O P Q R S FASTENERS Note Actual parts may appear slightly different than illustrated 2 of 11 ISSUED 10 22 04 SHEET 055 9236 5 01 10 06 Visit the InFocus Web Site at www infocus com Disengage connection block from projector mount assembly A by unscrewing captive screw and sliding out connection block as shown CONNECTION BLOCK CAPTIVE SCREW Installation To Wood J oist Finished Ceilings Exposed Wood J oists or Wood Beam Ceilings Drill two 5 32 4 mm dia holes to a minimum depth 2 of 2 5 64 mm Attach ceiling plate Q with two 14 x 2 5 6 mm x 65 mm wood screws F as shown using 3 8 10 mm socket wrench Tighten wood screws F so ceiling plate Q is firmly attached oa Pa A e Tighten wood screws so that ceiling plate is firmly attached but do not overtighten Overtightening can damage the screws greatly reducing their holding power e Never tighten in excess of 80 in Ib 9 N M Make sure that mounting screws are anchored into the center of the joist The use of an edge to edge stud finder is highly recommended Skip to step 7 For opti
Download Pdf Manuals
Related Search