Impex SM-2000 Owner's Manual
Contents
1. PRECAUTIONS This exercise machine is built for optimum safety However certain precautions apply whenever you operate a piece of exercise equipment Be sure to read the entire manual before you assemble or operate your machine In particular note the following safety precautions 1 Keep children and pets away from the machine at all times DO NOT leave children unattended in the same room with the machine 2 Only one person at a time should use the machine 3 If the user experiences dizziness nausea chest pain or any other abnormal symptoms STOP the workout at once CONSULT A PHYSICIAN IMMEDIATELY 4 Position the machine on a clear leveled surface DO NOT use the machine near water or outdoors 5 Keep hands away from all moving parts 6 Always wear appropriate workout clothing when exercising DO NOT wear robes or other clothing that could become caught in the machine Running or aerobic shoes are also required when using the machine 7 Use the machine only for its intended use as described in this manual DO NOT use attachments not recommended by the manufacturer 8 Do not place any sharp object around the machine 9 Disabled person should not use the machine without a qualified person or physician in attendance 10 Before using the machine to exercise always do stretching exercises to properly warm up 11 Never operate the machine if the machine is not functioning properly 12 A spotter is recommended during ex2. A Connect the Main Base Frame 8 to both Left amp Right Base Frames 1 amp 2 Secure them with one Bracket 7 two M10 x 3 Allen Bolt 4 four 4 Washers 5 and two M10 Aircraft Nuts 6 on each end of the Main Base Frame B Attach one Front Vertical Beam 9 to Left Base Frame 1 Secure it with two M10 x 2 3 Carriage Bolts 11 34 Washers 5 and M10 Aircraft Nuts 6 Repeat the same procedure to install the other Vertical Beam to the Right Base Frame 2 Insert the Guide Rods 16 into the hole on the Left amp Right Base Frame Secure them with two M8 x 3 8 Allen Set Screws 60 C Attach the Middle Vertical Beam 8 to the Main Base Frame 3 Attach the Rear Stabilizer 10 to the rear of the Main Base Frame 3 Secure them all together with two M10 x 3 Allen Bolts 4 four 3 4 Washers 5 and two M10 Aircraft Nuts 6 STEP 2 See Diagram 2 A Slide the two Safety Catches 12 onto the two Front Vertical Beams 9 and the Guide Rods 16 Push them down to the selected hole on the Front Vertical Beams and insert a Lock Knob 15 to obtain the desired height for each Catch B Slide two Rubber Bumpers 14 onto each of the Guide Rods 16 Then slide two Sliding Blocks 17 onto each of the Guide Rods C Note Help of another person is strongly recommended for this step Insert the 7 Long Bar 56 through the Sliding Block 17 from one si
3. Vertical Beam 8 Install a Pulley and secure it with a M10 x 1 3 Allen Bolt 24 two 93 4 Washers 5 and M10 Aircraft Nut 6 The Cable should be on top of the Pulley C Pull the Cable downward then attach a Pulley to the Cable Attach a Single Floating Pulley Bracket 49 to the Pulley Secure it with a M10 x 1 3 Allen Bolt 24 two 3 4 Washers 5 and one M10 Aircraft Nut 6 Let the Bracket hanging for now Draw the Cable around the Pulley upward towards the other side D Repeat Step A amp B above to install the Cable to the Right Butterfly DIAGRAM 6 STEP 7 See Diagram 7 A Attach the Upper Cable 25 to the open bracket at the front of the Upper Frame 21 Install a Pulley to the bracket Secure it with one M10 x 1 3 Allen Bolt 24 two 34 Washers 5 and one M10 Aircraft 6 B Draw the Cable along the Frame towards the back of the machine to the first open bracket Install another Pulley Pull the Cable downward and attach a Pulley to the Cable Install the Double Floating Pulley Brackets 50 to the Pulley Select any hole on the Bracket for now After completing the installation come back and adjust the tightness of the cable loop by selecting a different hole Let the Bracket hanging for now C Draw the Cable upward to the last bracket on the Upper Frame Install a Pulley Draw the Cable around the Pulley then pull the Cable down to the Weight Holder 31 Attach t
4. and service conditions for a period of two years on the Frame from the date of purchase This warranty extends only to the original purchaser IMPEX s obligation under this Warranty is limited to replacing or repairing at IMPEX s option All returns must be pre authorized by IMPEX Pre authorization may be obtained by calling IMPEX Customer Service Department at 1 800 999 8899 All freights on products returned to IMPEX must be prepaid by the customer This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes No other warranty beyond that specifically set forth above is authorized by IMPEX IMPEX is not responsible or liable for indirect special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyments or use costs of removal installation or other consequential damages or whatsoever natures Some states do not allow the exclusion or limitation of incidental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a partic
5. NOTE Please read all instructions carefully before using this product Safety Notice Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model SM 2000 Retain This Manual for Reference 07 30 01 OWNER S MANUAL MIP X PRODUCTS MARCY SMITH MACHINE SM 2000 14777 DON JULIAN RD CITY OF INDUSTRY CA 91746 Tel 800 999 8899 Fax 626 961 9966 ww impex fitness com info impex fitness com TABLE OF CONTENTS BEFORE YOUBEGIN 2 ae 1 IMPORTANT SAFETY ER EE 2 HARDWARE IDENTIFIER iri rnain a e A ANE 3 ASSEMBLY dl en Lee 4 EXPLODED Ee 12 PARTS IS RS RS EAEN dr On oi 13 AR PANTIN GE 14 ORDERING PART Susanne anna ne 14 BEFORE YOU BEGIN Thank you for selecting the MARCY SMITH MACHINE SM 2000 by IMPEX FITNESS PRODUCTS For your safety and benefit read this manual carefully before using the machine As a manufacturer we are committed to provide you complete customer satisfaction If you have any questions or find there are missing or damaged parts we guarantee you complete satisfaction through direct assistance from our factory To avoid unnecessary delays please call our TOLL FREE customer service number Our Customer Service Agents will provide immediate assistance to you Toll Free Customer Service Number 1 800 999 8899 Mon Fri 9 a m 5 p m PST ww impex fitness com info impex fitness com IMPORTANT SAFETY NOTICE
6. Vertical Beam Rear Stabilizer M10 x 2 Carriage Bolt Safety Catch 2 Square Sleeve Rubber Bumper Lock Knob Guide Rod Sliding Block 1 Bronze Bushing Front Top Beam 2 End Cap Upper Frame M10 x 2 Allen Bolt Rear Vertical Beam M10 x 1 Allen Bolt Upper Cable C clip Chain Lat Bar Grip 2 x 1 Sleeve Weight Holder M10 x 1 Allen Bolt Olympic Sleeve Spring Clip Weight Holder End Cap Weight Holder Bumper M6 x 5 8 Screw Pulley Left Butterfly Butterfly Pad Right Butterfly Bronze Bushing Butterfly Bracket Rubber Stopper Large Washer M10 x 3 Allen Bolt Cable End Clip Butterfly Bracket Single Floating Pulley Bracket Double Floating Pulley Bracket Q ty 1 51 Backrest Board 1 52 M8 x 2 2 Allen Bolt 1 53 4 Chrome Bar Sleeve 10 54 3 Rubber Bumper 60 55 M8 x 5 8 Allen Bolt 34 56 7 Long Bar 57 Plastic Olympic Sleeve 58 Olympic Sleeve End Cap 59 M8 x 2 Allen Set Screw 60 M8 x 3 8 Allen Set Screw 61 Arm Curl Handle 62 M10 x 23 Allen Bolt 63 Pulley Bushing 64 Lower Cable 65 Butterfly Cable 66 5 8 Washer 67 2 Square End Cap 68 M10 x 3 gt Carriage Bolt N NNN HF rm zkbM bM bM zb zk bM PM sch D zb ch zk P R D D D D B D E D D A 13 RON HH MH BB D ND D D ND HO IMPEX INC LIMITED WARRANTY IMPEX Inc IMPEX warrants this product to be free from defects in workmanship and material under normal use
7. de Position the 4 Chrome Bar Sleeve 53 in between the two Sliding Blocks 17 Continue inserting the 7 Bar through the 4 Chrome Bar Sleeve and the Sliding Block 17 on the other side D Slide two 3 Rubber Bumpers 54 onto the Bar from both sides Then plug two Plastic Olympic Sleeves 57 onto the bar from both sides Securely tighten the M8 x 5 8 Allen Bolt 55 on the Sliding Block 17 E Attach the Front Top Beam 19 onto top of the Front Vertical Beams 9 and Guide Rods 16 Secure them with two M10 x 3 Carriage Bolts 68 34 Washers 5 and M10 Aircraft Nuts 6 on each end Make sure the top of the Guide Rods 16 are inserted into the holes on the Front Top Beam 19 Secure them with two M8 x 3 8 Allen Set Screws 60 on the Front Top Beam 19 STEP 3 See Diagram 3 A Insert the Rear Vertical Beam 23 into the opening on the Rear Stabilizer 10 Secure it with two M10 x 2 Allen Bolts 22 four 34 Washers 5 and two M10 Aircraft Nuts 6 B Slide the Weight Holder 31 onto the Rear Vertical Beam 23 Push two Olympic Sleeves 33 onto the Weight Holder then attach two Spring Clips 34 onto the Sleeves DIAGRAM 3 lt gt STEP 4 See Diagram 4 A Attach the Upper Frame 21 to the top of Front Top Beam 19 Middle Vertical Beam 8 and Rear Vertical Beam 23 B Secure the Upper Frame 21 to the Rear Vertical Beam 23 wit
8. ercise WARNING BEFORE BEGINNING ANY EXERCISE PROGRAM CONSULT YOUR PHYSICIAN THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT IMPEX INC ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT SAVE THESE INSTRUCTIONS HARDWARE IDENTIFIER PLACE WASHER END OF BOLT OR SCREW ON CIRCLE TO CHECK FOR CORRECT SIZE REPLACEMENT PARTS MILLIMETERS Trank you for purcitasirtg IMPEX product Although we go to great effort to ensure O O the quality of our products Occasionally errors or omissions occur Should you M6 M8 M10 find either a defective or missing part in this product Please contact us for INCHES a replacement at the telephone number O C C QUESTION Em 1 800 999 8899 1 e 5 8 3 4 NOTE When installing a Aircraft Nut also called Nylon or Lock Nut Please use two adjustable wrenches to tighten down the Nut Hold down the Bolt with one wrench and use the other wrench to turn the Nut clockwise Length HEX HEAD BOLT QG CARRIAGE BOLT ALLEN BOLT AIRCRAFT NUT FLAT WASHER ASSEMBLY INSTRUCTION Tools Required to Assemble the Machine Two Adjustable Wrenches and Allen Wrenches NOTE It is strongly recommended this machine to be assembled by two or more people to avoid possible injury STEP 1 See Diagram 1
9. h two M10 x 2 Allen Bolts 22 four 34 Washers 5 and two M10 Aircraft Nuts 6 C Secure the Upper Frame 21 to the Middle Vertical Beam 8 with one M10 x 3 Allen Bolt 4 two 3 4 Washers 5 and one M10 Aircraft Nut 6 D Secure the Upper Frame 21 to the Front Top Beam 19 with one M10 x 3 Allen Bolt 4 two 34 Washers 5 and one M10 Aircraft Nut 6 DIAGRAM 4 STEP 5 See Diagram 5 Attach the Butterfly Bracket 43 to the Middle Vertical Beam 8 Secure it with one Bracket 48 two M10 x 3 Allen Bolt 4 four 34 Washers 5 and two M10 Aircraft Nuts 6 B Attach the Left Butterfly 39 to the Butterfly Bracket Secure it with one M10 x 3 Allen Bolt 46 and Large Washer 45 C Attach the Butterfly Pad 40 to the Left Butterfly 39 Secure it with two M8 x 2 1 2 Allen Bolts 52 and 5 8 Washers 66 D Repeat the Procedure B amp C to install the Right Butterfly 41 and its Pad E Attach the Backrest Board 51 to the Middle Vertical Beam 8 Secure it with two M8 x 2 2 Allen Bolts 52 and 5 8 Washers 66 DIAGRAM 5 STEP 6 See Diagram 6 A Insert one end of the Butterfly Cable 65 through the hole on the Left Butterfly 39 Attach a Cable End Clip 47 to the Cable Pull the Cable towards the back of the machine to secure the end B Draw the Cable to the Butterfly Bracket behind the
10. he end of Cable to a C clip 26 then connect to the Weight Holder D Attach the Lower Cable 64 to the opening on the bottom of the Middle Vertical Beam 8 Install a Pulley to the opening Attach two Pulley Bushings 63 to the holes Secure it with one M10 x 2 3 Allen Bolt 62 two 34 Washers 5 and one M10 Aircraft Nut 6 E Draw the Cable towards the back of the machine to the open bracket on the Rear Stabilizer 10 Install a Pulley Draw the Cable underneath around the Pulley then pull upward to the Double Floating Pulley Bracket 50 Install a Pulley Pull the Cable around the Pulley then downward to the bracket on the Middle Vertical Frame 8 Install another Pulley Draw the Cable around the Pulley then upward to the Single Floating Pulley Bracket 29 Connect the Cable to the Bracket and secure it with one M10 x 1 Allen Bolt 32 two 34 Washers 5 and one M10 Aircraft Nut 6 F Attach C clips 26 to each end of the Chain 27 Connect one end to the Upper Cable 25 and the other end to the Lat Bar 28 G Attach the Arm Curl Handle 61 to the Lower Cable 64 10 DIAGRAM 7 SE cs 11 wi G GG wi H A A Fz A O Ay Ge a 12 PARTS LIST KEY NO DESCRIPTION Joo ND Left Base Frame Right Base Frame Main Base Frame M10 x 3 Allen Bolt 3 Washer M10 Aircraft Nut Bracket Middle Vertical Beam Front
11. ular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal right You may also have other rights which vary from state to state Register on line at www impex fitness com IMPEX INC 14777 Don Julian City of Industry CA 91746 ORDERING REPLACEMENT PARTS Replacement parts can be ordered by calling our Customer Service Department toll free at 1 800 999 8899 during our regular business hours Monday through Friday 9 am until 5 pm Pacific standard time info impex fitness com When ordering replacement parts always give the following information Model Description of Parts Part Number Date of Purchase Pon 14
Download Pdf Manuals
Related Search