Image IMSB20701 User's Manual
Contents
1. Drain Hose Valve Knob Open the valve by turning the knob counterclock wise The water will begin to drain When the spa is empty close the valve and remove the garden hose Return the drainage hose to the clip and re attach the access cover Refill the spa and treat the water with chemicals see pages 8 and 14 15 WINTER USE AND CARE The RENEW 207 is designed for year round use If you decide to store the spa for the winter store it in a warm dry location Follow the steps below to winterize the spa 1 2 3 OND Drain the spa see DRAINING THE RENEW 207 on page 14 Remove all remaining water from the spa shell Dry the spa shell with towels Set the air control on the console to the lowest setting Use a wet dry vacuum to pull any remain ing water from the system To do this place the vacuum nozzle over each thera jet starting with the highest one and finishing with the lowest one Set the air control on the console to the highest setting and repeat step 3 Clean the spa shell see page 13 Clean the filter see page 13 Re attach the access cover Re attach the spa cover TROUBLE SHOOTING Most problems can be solved by following the simple steps below Find the symptom that applies and follow the steps listed If further assistance is needed call our Customer Service Department toll free at 1 877 897 7493 Monday through Friday 6 a m until 6 p m Mountain Time2. REDUCE THE RISK OF DROWNING ELECTRIC SHOCK OR SERIOUS INJURY READ THE FOLLOWING IMPORTANT PRECAUTIONS BEFORE USING THE RENEW 207 READ AND FOLLOW ALL INSTRUCTIONS It is the responsibility of the owner to ensure 9 Do not bring any object into the RENEW 207 that all users of the RENEW 207 are adequately that could damage the spa shell informed of all precautions 10 Never insert any object into any opening Use the RENEW 207 only as described in this manual 11 Do not use breakable containers near or in the RENEW 207 The RENEW 207 is intended for home use only Do not use the spa in a commercial 12 Do not sit on the spa cover or place objects rental or institutional setting on it it is not designed to support weight Use the RENEW 207 only on a level surface 13 Remove any water or debris that may collect Do not use the spa on carpet or other materi on the spa cover als that could be damaged by moisture Do not use the spa on rough or sharp surfaces 14 Keep children and pets away from the such as gravel or wood chips RENEW 207 when it is not in use The RENEW 207 will weigh approximately 15 Keep all chemicals away from children and 1 500 pounds when it is filled with water Be pets sure that the location you select for the spa will support this weight plus the weight of 16 The pH and chemical balance of the water the occupants must be maintained as explained in this man ual see pages 11 and 14 Failure to do so Inspec
3. 1 SYMPTOM THE SPA WILL NOT OPERATE a Check the power cord The power cord must be plugged into a grounded outlet see PLUGGING IN THE RENEW 207 on page 10 b Check the GFCI breaker to see if it is tripped or if it was not turned on Reset the GFCI breaker SYMPTOM THE CIRCUIT BREAKER OR GFCI BREAKER TRIPS WHILE THE SPA IS OPERATING a Reset the circuit breaker If the circuit breaker trips again contact a qualified electrician for service SYMPTOM THE PUMP HUMS a The filter may be dirty or damaged Remove the filter from the filter housing of the spa jet unit and clean or replace the filter b The pump may have a foreign object stuck in the impeller Contact our customer service department or if your spa is no longer under warranty you may also contact a local spa and pool service provider c The pump may have a loose wire connection Contact our customer service department or if your spa is no longer under warranty you may also contact a local spa and pool service provider SYMPTOM THE PUMP HUMS BUT DOES NOT ROTATE a The pump may be jammed Contact our cus tomer service department If your spa is no longer under warranty you may wish to contact a local spa and pool service provider SYMPTOM THE PUMP IS NOISY WHILE OPERATING a There may be debris in the pump Contact our customer service department If your spa is no longer under warranty you may wish to contact a local spa and
4. Model No IMSW20701 IMSG20701 IMSB20701 Serial No The serial number can be found in the location shown below Write the serial number in the space above Serial Number Decal on the frame behind the access cover QUESTIONS PLEASE CALL DIRECT TO OUR TOLL FREE CUSTOMER HOT LINE The trained technicians on our customer hot line will provide immediate assistance free of charge to you CUSTOMER HOT LINE 1 877 897 7493 Mon Fri 6 a m 6 p m MST CAUTION Read all precautions and instruc tions in this manual before using this equipment Save this manual for future reference USER S MANUAL Q www workoutwarehouse com new products prizes fitness tips and much more TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS occ 3 BEFORE YOU BEGIN LARGA e RO LL Abele LIT ES ENS 6 CHOOSING A LOCATION FOR THE RENEW 207 7 SETUP AND ASSEMBDLY cui uy puede t a ek IRAE Puer ee Ge ad 8 POSTING THE WARNING SIGN ssseeeee eR e Re 10 USING THE RENEW 207 oo a ee eoru E RR Ce ees 10 MAINTENANGE e as a EO RR EUN iaia 13 TROUBLE SHOOTING a A PR get ES 16 PART CIST COE 18 EXPLODED DRAWING Ia Adie o A ged e les 19 ORDERING REPLACEMENT PARTS Back Cover LIMITED HYDROTHERAPY SPA WARRANTY Back Cover IMAGE is a registered trademark of ICON Health amp Fitness Inc 2 IMPORTANT SAFETY INSTRUCTIONS WARNING
5. To unlock the buckles insert the key and turn it coun terclockwise 1 4 turn Buckle SPA JET OPERATION After the spa cover is secured you can fur ther tighten it by adjusting the self attaching flaps on each end of the spa cover Adjustment Always keep the buckles locked when the spa is not in use Keep the keys in a safe place out of the reach of children Refer to the diagram above The function of each fea ture is explained below The three fixed thera jets A located on one end of the spa focus a water massage on your back The three adjustable thera jets B can be adjusted for a custom water massage One of the jets focuses a water massage on your lower back a second jet focuses a water massage on your upper back and a third jet near the floor of the spa focuses a water mas sage on your legs Note The adjustable thera jets can be closed and opened by pushing and pulling the nozzles If no air flows through the thera jets when the air control is turned counterclockwise simply pull the nozzles slightly 12 The filter C can be removed for cleaning and replacement see CHECKING AND CLEANING THE FILTER on page 13 The suction vents D located near the floor of the spa bring water into the pump in order to operate the system The suction covers should always be in place over the suction vents Never operate the spa with out the suction covers in place T
6. USING THE CONSOLE The function of each console control is explained below Air Control Temperature Control Temperature Control This control is used to set the temperature of the water The water heats at about 3 0 F per hour with the cover on The thermostat can be set to heat the water from 70 F to 104 F Always use an accurate thermometer to check the tempera ture of the water Note The RENEW 207 features automatic freeze pro tection If the water temperature falls below 40 F the pump will begin circulating and heating the water to prevent the water from freezing Pump Control This control turns the thera jets on and off To turn the thera jets on press the control once To turn the thera jets off press the control again The thera jets will remain off for 20 minutes After 20 minutes the pump will begin cycling to heat the water if the temperature falls below the minimum setting Note To keep the heat cycle from running the power cord must be unplugged Air Control This control determines the amount of air flowing through the thera jets during operation If the control is turned counterclockwise the amount of air will increase if the control is turned clockwise the amount of air will decrease SECURING THE SPA COVER To secure the spa cover snap the latches on the spa cover into the buckles on the side of the spa To lock the buckles insert the key and turn it clockwise 1 4 turn
7. decals shown below and familiarize yourself with the warnings on the decals AWARNING WARNING Exposure of the spa surface to direct sunlight or ultra violet rays may cause damage to the spa s surface and will void the surface warranty of this spa PREVENT DROWNING i SUPERVISE CHILDREN AT ALL TIMES ATTACH SPA COVER AFTER EACH 3 SPA HEAT CAN CAUSE HYPERTHERMIA AND UNCONSCIOUSN 4 SPA HEAT IN CONJUNCTION WITI ALCOHOL DRUG CAN CAUSE UNCONSCIOUSNESS PREVENT ELECTROCUTION 1 NEVER PLACE ANY ELECTRIC APPLIANCE WITHIN 5 FEET OF SPA S OR MEDICATION NOTE THIS MARKING IS TO BE REMOVED ONLY BY THE OWNER A WARNING Read all instructions before using the RENEW 207 ICON assumes no respon sibility for personal injury or property damage sustained by or through the use of this product SAVE THESE INSTRUCTIONS BEFORE YOU BEGIN Congratulations for selecting the new IMAGE RENEW 207 massage spa The RENEW 207 offers the features and quality of a traditional hot tub at an affordable price providing the benefits of hydrotherapy in the comfort and privacy of your home Hydrotherapy is a proven method for soothing tired muscles after exercise or for relieving the stress of a busy life The warm environment stimulates blood flow which is essential to the healing process and the powerful massage action eases tension and stress throughout the body The RENEW 207 gives you the specialized treatment you need to
8. 52m of the spa DANGER Risk of electric shock Do not set up the RENEW 207 within five feet of any metal objects or surfaces As an alternative you may use the spa within five feet of metal objects if each metal object is permanently connected to the wire connector on the pump motor of the spa by a minimum No 8 AWG 804 mm solid copper conductor see instruction 24 Do not operate the pump motor when the RENEW 207 is empty The pump motor may be damaged if it is operated without water circulating DANGER Risk of drowning Exercise extreme caution to prevent unauthorized and unsupervised use of the RENEW 207 by chil dren Children must always be supervised 28 29 30 31 32 33 DANGER To reduce the risk of drowning Never use the RENEW 207 alone Children should not use the spa unless they are supervised by an adult Keep pets away from the spa at all times Always replace and lock the spa cover when the spa is not in use WARNING To reduce the risk of injury The water temperature should never exceed 104 F 40 C Temperatures between 100 F 38 C and 104 F 40 C are considered to be safe for healthy adults However if you plan to remain in the RENEW 207 for more than 10 to 15 minutes a lower temperature is recom mended Lower temperatures are also recom mended for children Children should not be allowed to swim under the surface in the spa WARNING To reduce the risk o
9. and motor This warranty extends only to the original purchaser ICON s obligation under this warranty is limited to replacing or repairing at ICON s option the product through one of its authorized service centers All repairs for which warranty claims are made must be pre authorized by ICON This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by ICON authorized service personnel to products used for commercial or rental purposes or to products used as store display models Specifically excluded are damages caused by or attributable to the follow ing incidents any damage to the surround or frame attributable to improper handling or freight damage damage resulting from improper winterization damage to the spa shell resulting from improper chemical treatment damage to the spa shell resulting from exposure to extreme temperatures or damage to the spa shell resulting from exposure to direct sunlight and ultraviolet rays while the spa is empty damage to the pump motor plumbing and components due to improper maintenance chemical treatment or expo sure or damage resulting from failure to properly follow user s manual installation operating or mainte nance instructions Also excluded are consumable components including but not restricted to filter car tridges No other warranty beyond that specifically set forth above
10. be close to a source of water Do not use the RENEW 207 on carpet or other material that may be damaged by moisture We recommend that you place the spa on a water and stain resistant non slip surface with a floor drain for any water that may splash from the spa Be sure that the location you choose is stable It must be able to support the weight of the RENEW 207 when it is filled with water plus the weight of the occupants The spa weighs approximately 1 500 pounds when filled with water Do not use the RENEW 207 above a finished liv ing area due to the risk of water damage Be sure that there is room around the RENEW 207 to permit servicing of the unit The dimensions of the spa are 3 7 W x 7 6 Lx 2 5 H You should allow for this size when choosing the loca tion The RENEW 207 is not designed for in floor installation However it is compatible with a deck System that is built flush with the top of the spa provided you leave access to the motor for ser vice Be sure to note any other considerations such as aesthetics or privacy concerns that may affect the safety or enjoyment of using the RENEW 207 If you set up the RENEW 207 outside 1 Check your local building codes concerning the use of outdoor spas The location must be close to an electrical outlet Do not use an extension cord with the RENEW 207 The RENEW 207 should be close to a source of water We
11. cover up until the bottom of the cover clears the trim along the bottom of the spa unit Slide the cover into place and re attach it with the two access cover screws DRAINING THE RENEW 207 The RENEW 207 should be drained at least four times a year and refilled with clean water You may need to drain the spa more often depending on the user load This must be done because after repeated chemical treatment the water becomes chemically saturated Once this happens additional chemical treatment of the water is no longer effective The spa should also be drained if it will not be used for long periods of time The spa must always be drained before major repairs are made The RENEW 207 should always be covered when itis empty Direct sunlight can cause extensive damage The surface of the spa shell can reach temperatures as high as 150 F in a matter of min utes if exposed to the sun while it is empty These high temperatures can cause significant damage such as blistering of the shell surface and warp ing of the spa shell Any damage caused by sun exposure is not covered under warranty To drain the RENEW 207 follow these steps 1 Set the temperature control on the console to the lowest setting 2 Unplug the power cord 3 4 Remove the drainage hose from the clip and Remove the access cover from the spa attach a garden hose to the valve on the drainage hose
12. pool service provider 16 b The pump may have a bad bearing Contact our customer service department If your spa is no longer under warranty you may wish to con tact a local spa and pool service provider 6 SYMPTOM THE WATER DOES NOT HEAT a The pump in the spa jet unit is the heater If the pump is operating the water should heat Cover the RENEW 207 with the spa cover The spa cover must be tight with the insulating liner in place Set the air control to low The water will heat at a rate of 3 0 F per hour If you are using the spa indoors and the room temperature is maintained at 70 F it will take approximately 10 to 15 hours for the water to reach the set temperature If you are using the RENEW 207 outdoors it may take longer for the water to heat See the chart below for the approximate heating time Heating Time 10 to 15 hours 16 to 25 hours 26 to 30 hours Air Temperature 70 F 50 F to 70 F 30 F to 50 F If the water still has not heated after four days contact our customer service department or if your spa is no longer under warranty you may also contact a local spa and pool service provider 7 SYMPTOM THE SPA CONTINUES TO RUN AFTER IT HAS BEEN SHUT OFF a To turn the spa jets on press the pump control once To turn the spa jets off press the control again After you press the control once the spa jets will shut off for about 30 seconds and then restart Press the contro
13. 1 Screw Cover Spacer Key Foot Pump Access Panel Chemical Starter Pack pH Test Kit T Molding Short Panel Screw Long Panel Screw Jump Wire Blue Ground Wire Corner Panel Cage Nut Warning Sign User s Manual Note indicates a non illustrated part Specifications are subject to change without notice 18 EXPLODED DRAWI NG Model No IMSW20701 IMSG20701 IMSB20701 R0401A 19 ORDERING REPLACEMENT PARTS To order replacement parts simply call our Customer Service Department toll free at 1 877 897 7493 Monday through Friday 6 a m until 6 p m Mountain Time excluding holidays To help us assist you please be prepared to give the following information when calling The MODEL NUMBER of the product IMSW20701 IMSB20701 IMSG20701 The NAME of the product IMAGE RENEW 207 hydrotherapy spa The SERIAL NUMBER of the product see the front cover of this manual The KEY NUMBER and DESCRIPTION of the desired part s see the PART LIST on page 18 LIMITED HYDROTHERAPY SPA WARRANTY ICON Health amp Fitness Inc ICON warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of ninety 90 days from the date of pur chase ICON extends a limited five 5 year warranty on the spa shell structure ICON extends a limited two 2 year warranty on the pump
14. THE RENEW 207 on page 10 plug the power cord directly into a grounded circuit capable of carrying 15 or more amps No other appliance should be on the same circuit Replace the power cord immediately if damaged 20 21 22 23 24 25 26 27 Do not use an extension cord with the RENEW 207 this could damage the motor and will void the warranty DANGER If you will be using the RENEW 207 outside do not bury the power cord Keep the power cord away from lawn mow ers hedge trimmers and other similar equip ment WARNING The power cord is equipped with a Ground Fault Circuit Interrupter GFCI located at the end of the power cord The GFCI must be tested before each use To test the GFCI press the test button while the RENEW 207 is running The spa should shut off Press the reset button The spa should resume normal operation If the spa contin ues to run after the test button is pressed the GFCI is damaged Do not use the spa until the GFCI has been repaired or replaced by a qualified electrician Keep all electrical appliances such as radios telephones televisions and lights at least five feet 1 52 meters away from the water A wire connector is provided on the electron ics of the RENEW 207 to connect a minimum No 8 AWG 804 mm solid copper conductor between the spa and any metal equipment electrical enclosure made of metal metal water pipes or conduit within five feet 1
15. TROL IS TURNED COUNTER CLOCKWISE a The three adjustable thera jets can be closed and opened by pushing and pulling the noz zles If no air flows through the thera jets when the air control is turned counterclockwise sim ply pull the nozzles slightly PART LIST Model No IMSW20701 IMSG20701 IMSB20701 Key No Qty 12 000 c DNA py co Description Buckle Screw Buckle 1 4 x 1 25 Bolt Lock Washer Heater Wire Harness Temperature Hi Limit Probe Assembly Console Overlay Pressure Switch Control Box Removable Collar Pump Motor Insulating Liner Spa Cover Drowning Warning Decal Flat Washer Sun Warning Decal Collar Screw Heater Terminal Cover Small Switch Cover Large Switch Cover Filter Suction Cover Screw Suction Cover Thermostat Assembly Power Supply Mounting Screw Adjustable Thera jet Compression Fitting Air Control Knob On Off Switch Assembly Drain Hose Cap Hose Washer Key No Qty 32 1 33 2 34 1 35 1 36 2 37 1 38 1 39 1 40 2 41 1 42 1 43 1 44 1 45 1 46 2 47 2 48 2 2 1 2 1 1 2 16 8 1 2 4 24 1 1 R0401A Description Filter Cap w O Ring 10 Kep Nut Heater Assembly LCD Display Rubber Isolator Thermostat Knob Quick Mount Bracket On Off Wire Harness Switch Cover Screw Heater Gasket Flat Heater Gasket Display Bracket 10 x 625 Screw Control Bracket Motor O ring 10 x
16. d spray it with a hose Allow the cover to dry thoroughly CLEANING THE SPA SHELL The spa shell should be cleaned with a mild soap solution Do not use solvents The spa should always be clean and dry before being moved or stored MAINTAINING THE SPA EXTERIOR The surround has been treated at the factory For information and supplies to maintain the beauty and color of your surround call our Customer Service Department toll free at 1 877 897 7493 CHECKING AND CLEANING THE FILTER The filter should be checked periodically for build up of dirt and oil Follow the steps below 1 Turn off the power Filter 2 Remove the filter Cap cap 3 Lift the filter from the filter housing 4 Check the filter for dirt and debris If the filter needs to be cleaned rinse the filter with a hose If the filter is still dirty soak it in a cleaning solution obtained from a pool and spa supply store 5 Inspect the filter for damage Replace the filter if there are any signs of damage 6 Re insert the cleaned filter into the filter housing 7 Re attach the filter cap SANITIZING THE RENEW 207 Please refer to your local pool and spa supplier for information concerning which chemicals you should use in your area to sanitize the spa The most common sanitizing agent is a solid bromine concentrate The amount required varies according to several factors such as user load temperature water conditions and so forth Proper
17. f injury Always use an accurate thermometer to determine the water temperature before using the RENEW 207 WARNING To reduce the risk of injury Pregnant women should consult with their physician before using the RENEW 207 Pregnant women should not use the spa if the water temperature is above 100 F 38 C the unborn child could be seriously harmed This is especially important during the first 90 days of the pregnancy DANGER To reduce the risk of drowning Prolonged immersion in the RENEW 207 may cause hyperthermia a dangerous condition which occurs when the internal body temper ature rises several degrees above the normal body temperature of 98 6 F The symptoms of hyperthermia are nausea dizziness drowsiness and fainting Effects include a lack of awareness inability to perceive heat or danger and a greater risk of drowning due to a loss of consciousness Special note Individuals suffering from hyperthermia may be unable to realize that they must exit the spa and they also may be physically unable to do so WARNING To reduce the risk of drowning Do not use the RENEW 207 if you are under the influence of alcohol or drugs Heat from the water in conjunction with alcohol or drugs can cause unconsciousness 34 35 36 37 WARNING To reduce the risk of injury or drowning Consult your physician about pos sible side effects of any medications you may be taking before using the RENEW 207 Heat fro
18. feel your best Ground Fault Circuit ___ lt 3 Interrupter GFCI Power Cord For your benefit read this manual carefully before using the RENEW 207 If you have additional ques tions please call our Customer Service Department toll free at 1 877 897 7493 Monday through Friday 6 a m until 6 p m Mountain Time excluding holidays To help us assist you please mention the product model number and serial number when calling The model number and serial number can be found on a decal attached to the frame inside the spa see the front cover of this manual Before reading further please familiarize yourself with the parts that are labeled in the drawing below H poss Cover Latch Spa Shell Filter Locking Buckle Wood Panels CHOOSING A LOCATION FOR THE RENEW 207 There are many factors to consider when choosing a location to set up the RENEW 207 These factors vary depending on whether you plan to use the spa inside or outside We have listed several factors you may wish to consider as you decide where you want to set up the spa If you set up the RENEW 207 inside 1 The RENEW 207 will increase the level of humidi ty in your home The location you choose should be well ventilated You may need to install a venti lation fan or use a dehumidifier The location must be close to an electrical outlet Do not use an extension cord with the RENEW 207 The RENEW 207 should
19. he spa is ozone ready An optional ozone generator can be installed to utilize the ozone jet E Ozone provides a way to help sanitize your spa with minimal chemical treatment MAINTENANCE The RENEW 207 is designed to provide years of enjoyment Follow the guidelines below to properly maintain the spa MAINTENANCE SCHEDULE DAILY Check the water level If necessary refill the spa to the level shown in step 3 on page 8 Adjust the pH balance and sanitizer level if needed see WATER CHEMISTRY on page 14 WEEKLY Clean the spa shell at the waterline Check and thoroughly clean the filter see CHECK ING AND CLEANING THE FILTER on this page Replace the filter if needed see ORDERING REPLACEMENT PARTS on the back cover MONTHLY Clean the spa cover see MAINTAINING THE SPA COVER below Soak the filter for two hours in a trisodium phos phate TSP solution Rinse the filter in clean water Replace the filter if needed see ORDERING REPLACEMENT PARTS on the back cover EVERY THREE MONTHS Drain the spa and refill it with clean water Sanitize and test the pH of the water Check for any leaks around the pump or joints in the pipes The seals will wear out over time detect ing leaks early can reduce repair costs Clean the interior of the spa Do not use solvents or waxes MAINTAINING THE SPA COVER The spa cover should be cleaned monthly To clean the spa cover hang it over a clothesline an
20. included One Phillips screwdriver gt Console Screws Pump Fittings P i 4 Attach the nozzle of the included air pump to the valve on the Insulating Liner 4 Fill the Insulating Liner with air Be careful not to overfill the Insulating Liner Lay the Spa Cover 11 on the floor as shown Set the Insulating Liner 4 inside the Spa Cover Insert one of the four straps on the inside of the Spa Cover 11 through one of the loops on the Insulating Liner 4 Attach the latch on the strap to the buckle on the other end of the strap Attach the other three straps on the inside of the Spa Cover to the Insulating Liner in the same way Place the Spa Cover 11 over the spa making sure that the cutout in the Insulating Liner 4 is aligned with the Console not shown 5 Place the Spa Cover 13 over the spa Make sure that the Spa Cover is centered Snap a Buckle 2 onto each of the eight latches on the Spa Cover 13 Pull down one of the straps on the Spa Cover 13 and hold the Buckle 2 against the side of the spa Note To position the Buckle correctly have a sec ond person hold the strap on the opposite side of the Spa Cover tight The Spa Cover must be tight Do not place the Buckle over the grooves between the wood panels Refer to the inset drawing Remove the latch from the Buckle 2 Attach the Buckle t
21. ing materials from the spa shell do not dispose of the packing materials until assembly is completed Assembly requires two people 1 Before beginning assembly make sure that you have read and understand the information in the box above and on the previous page Remove the four screws from the access cover on the console side of the spa Remove the access cover by sliding it down and then pulling the bottom of it away from the spa Be careful not to damage the Spa Shell 15 Remove the Power Cord with the GFCI 9 from inside the spa 2 Close the valve knob on the drain hose Tighten the two pump fittings Refer to step 1 above Re attach the access cover with the for screws 3 Remove the warning decals not shown from the Spa Shell 15 Using a damp cloth wipe the Spa Shell clean Before filling the spa make sure that it is in the desired position and that there is room to easily service the spa Once the spa is filled it will have to be drained before it can be moved Using a garden hose or other clean water source begin filling the spa Do not use soft water The spa may be filled with cold water however if warm or hot water is used the spa will be ready for use sooner Fill the spa until the water is at the level shown at the right Do not overfill the spa Read each assembly step before you begin During assembly make sure that all parts are turned as shown in the drawings TOOLS REQUIRED not
22. is authorized by ICON ICON is not responsible or liable for indirect special or consequential damages arising out of or in con nection with the use or performance of the product or damages with respect to any economic loss loss of or damage to property including water damage loss of revenues or profits loss of enjoyment or use costs of removal installation or other consequential damages of whatsoever nature Some states do not allow the exclusion or limitation of incidental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal rights You may also have other rights which vary from state to state ICON HEALTH amp FITNESS INC 1500 S 1000 W LOGAN UT 84321 9813 Part No 174260 R0401A Printed in USA 2000 ICON Health amp Fitness Inc
23. l again The spa jets will remain off for 20 minutes at which time they will begin running the filter cycle Note At any time after the spa jets have been shut off the pump will begin cycling the water if the tem perature falls below the minimum setting 8 10 SYMPTOM THE WATER PULSATES OR THERE IS MINIMUM WATER FLOW a This usually occurs only when the water level is low Add water to the level shown in step 3 on page 8 b The filter may be dirty Check the filter and clean it if necessary SYMPTOM THE WATER IS NOT BEING CLEANED BY THE FILTER a Check to see if the filter is in place Clean the filter if it is dirty b Check the chemical balance of the water If the pH is incorrect the sanitizing agents will not function properly SYMPTOM THE WATER LEVEL DROPS a Some water loss due to evaporation is normal If rapid water loss occurs or if you notice wet 17 11 ness on the floor around the RENEW 207 the spa shell may have a leak Contact your local spa and pool service provider for repairs b A clamp or seal inside the pump compartment may be loose Check inside the pump compart ment for excess water and watch the pump unit while it is operating to see if water drips from any of the plumbing If you can identify the location of the leak inside the spa jet unit tight en the clamp or replace the damaged seal SYMPTOM NO AIR FLOWS THROUGH THE ADJUSTABLE HYDROTHERAPY JETS WHEN THE AIR CON
24. m the water in conjunction with some medications may cause drowsiness and increase the risk of drowning Others can effect blood pressure heart rate and circula tion Do not use the RENEW 207 immediately after strenuous exercise If you feel pain or dizziness at any time while using the RENEW 207 discontinue use and contact a physician WARNING To reduce the risk of injury It is especially important for persons over the age A WARNING AVOID DROWNING RISK STAY OFF COVER WILL NOT SUPPORT WEIGHT KEEP CHILDREN AWAY CHILDREN OR OBJECTS CANNOT BE SEEN UNDER COVER REMOVE STANDING WATER CHILD CAN DROWN ON TOP OF COVER REMOVE COVER S COMPLETELY BEFORE ENTRY OF BATHERS ENTRAPMENT POSSIBLE NON SECURED OR IMPROPERLY SECURED COVERS ARE A HAZARD FAILURE TO FOLLOW ALL INSTRUCTIONS MAY RESULT IN INJURY OR DROWNING THIS IS NOT A SAFETY COVER 38 39 40 of 35 or persons with pre existing health problems such as obesity heart disease high or low blood pressure circulatory prob lems or diabetes to consult their physician before using the RENEW 207 WARNING The spa jets produce a stream of water with relatively high pressure Prolonged exposure of a localized area of the body may cause bruises to the skin The included warning sign must be posted where all users of the IMAGE 207 can see and read it see POSTING THE WARNING SIGN on page 10 WARNING DECAL PLACEMENT Locate the
25. n this range If the pH level exceeds 7 8 dissolved minerals can build up and clog the plumbing in the spa jet unit If the pH level falls below 7 2 the acid level in the water will begin to cor rode the metal parts in the spa jet unit Also the sani tation agents in the water will not be effective if the pH level is not properly maintained Damage caused by improper pH levels is not covered under the warranty To maintain the proper pH level test the pH of the water regularly You will need a pH test kit not includ ed which can be obtained at a pool and spa supply store The pH reading should be between 7 2 and 7 8 If the level is too low add a pH increaser usually soda ash If the level is too high add a pH reducer usually sodium bisulfate Test the water again after five minutes See the instructions with your pH test kit for additional information about testing and adjusting the pH 14 REMOVING AND ATTACHING THE ACCESS COVER To remove the access cover first remove the four access cover screws Slide the access cover down and then pull the bottom of it away from the spa unit Be careful not to damage the spa shell as you remove the cover Access Cover If the spa will be stored for any period of time place the power cord inside the spa unit before re attaching the access cover To reattach the access cover insert the top of the cover under the edge of the spa shell Slide the
26. o the wood panel with two Buckle Screws 1 Attach the other seven Buckles 2 to the wood pan els in the same way Remove the Spa Cover 13 from the spa Before using the spa carefully read USING THE RENEW 207 beginning on page 10 6 Before using the spa follow the instructions on page 10 to post the included warning sign Do not allow the spa to be used before the warning sign is posted POSTING THE WARNING SIGN The included warning sign shown below must be posted on a wall or fence where it will be visible to all users of the RENEW 207 If the spa is moved the sign must also be moved and reposted near the spa If the sign becomes lost or illegible call our toll free Customer Hot Line at 1 877 897 7493 to obtain a free replacement sign Post the sign as described above AWARNING DURING PREGNANCY SOAKING IN HOT WATER MAY CAUSE DAMAGE TO THE FETUS LIMIT USE TO 10 MINUTES AT A TIME PREVENT DROWNING SPA HEAT SPEEDS UP EFFECTS OF ALCOHOL DRUGS OR MEDICINE AND CAN CAUSE UNCONSCIOUSNESS IMMEDIATELY LEAVE SPA IF UNCOMFORTABLE OR SLEEPY O USING THE RENEW 207 The RENEW 207 is designed to seat two adults The spa holds 150 gallons of water and offers an automat ic programmable heating 70 F to 104 F and filtra tion system Seven thera jets soothe and relax tired sore muscles and the strength of the massage is adjustable Follow the guidelines below to use and maintain the spa for you
27. r long term enjoyment PLUGGING IN THE RENEW 207 Once the RENEW 207 is filled with water the power cord can be plugged in and the spa can be turned on Note The first time the power cord is plugged in the spa will turn on automatically When connecting the power cord plug the power cord directly into a grounded circuit capable of carrying 15 or more amps No other appliance should be on the same circuit Replace the power cord immediately if it becomes damaged 10 PREVENT CHILD DROWNING WATER ATTRACTS CHILDREN ALWAYS ATTACH A SPA COVER AFTER EACH USE There is a Ground Fault Grounded uo cm us of carrying GFCI on the Li or more amps power cord Always test Test and Reset the GFCI B uttons before using the RENEW 207 First turn on the RENEW 207 by pressing the pump control on the console Once the unit is running press the GFCI test button The spa should shut off Press the reset button The spa should resume normal operation If the spa continues to run after the test button is pressed the GFCI is damaged Do not use the spa until the GFCI has been repaired or replaced by a qualified electrician TESTING AND TREATING THE WATER For water maintenance the hydrotherapy spa comes with a starter chemical pack for maintaining the water in the spa Additional chemicals can be purchased at a pool and spa supply store Always keep the chem icals away from children and pets The fi
28. recommend that you place the RENEW 207 on a water and stain resistant non slip surface Do not use the spa on rough or sharp surfaces such as gravel or wood chips Be sure that the location you choose is stable It must be able to support the weight of the RENEW 207 when it is filled with water plus the weight of the occupants The spa weighs approximately 1 500 pounds when filled with water Consider environmental factors such as rain wind shade sunlight and so forth You should be able to monitor the use of the RENEW 207 from your home to prevent unautho rized use by children You may want to enclose the spa with a fence and self latching gate to pre vent unauthorized use Be sure that there is room around the RENEW 207 to permit servicing of the spa The dimensions of the spa are 3 7 W x 7 6 Lx 2 5 You should allow for this size when choosing the loca tion The RENEW 207 is not designed for in ground installation However it is compatible with a deck system that is built flush with the top of the spa provided you leave access to the motor for ser vice Be sure to note any other considerations such as aesthetics or privacy concerns that may affect the safety or enjoyment of using the RENEW 207 SETUP AND ASSEMBLY Before beginning assembly carefully read the following information and instructions Place all parts of the spa in a cleared area and remove the pack
29. rst time you use the spa you must test and treat the water You must also treat the water each time you refill the spa Once you have verified that the spa is functioning properly and the water has circulat ed for a while remove the spa cover and follow the instructions contained in your starter chemical pack Allow the water to circulate for five minutes Next test the pH of the water You will need a pH test kit not included which can be obtained at a pool and spa supply store The pH reading should be between 7 2 and 7 8 Follow the instructions contained in your starter chemical pack to achieve the proper pH level See WATER CHEMISTRY on page 14 for information concerning proper water maintenance STARTING THE RENEW 207 Once you have tested the GFCI you should verify the water flow from the pumping unit Set the air control on the console to the lowest setting see USING THE CONSOLE on the next page The pumping unit will heat the water as it pumps Cover the RENEW 207 with the spa cover and liner The spa cover must be tight See SECURING THE SPA COVER on page 12 The water will heat at about 3 0 F per hour with the cover on If you are using the spa indoors and the room temperature is maintained at 70 F it will take approximately 10 to 20 hours for the water to reach the set temperature The temperature and water flow can be set or changed by the controls on the console see USING THE CONSOLE at the right 11
30. t and tighten all parts regularly replace may cause injury to users or damage to the any worn or missing parts immediately spa and will void the warranty DANGER Risk of injury Do not remove or 17 Individuals with infections and open sores or alter the covers on the suction fittings Never wounds should not use the RENEW 207 operate the RENEW 207 if the suction guard Bacteria thrive in warm and hot water Always is missing or broken If you need to replace a keep the spa disinfected and maintain the suction fitting use only manufacturer recom proper chemical balance mended parts Keep hair and body away from the suction guard Do not allow long hair to 18 Always shower before and after using the float freely in the water long hair should be RENEW 207 This will remove any deodorant restrained with a bathing cap perspiration or body oils that could contami nate the water Showering after will remove IMPORTANT Do not allow the RENEW 207 to any residual chemicals and any bacteria that be exposed to direct sunlight when it is may have been in the spa empty The surface of the spa shell can reach temperatures as high as 150 F in a matter of 19 DANGER When connecting the power cord minutes if exposed to the sun while it is empty These high temperatures can cause significant damage such as blistering of the shell surface and warping of the spa shell Any damage caused by sun exposure is not covered under warranty see PLUGGING IN
31. water maintenance is a complex process We recommend that you contact your local pool and spa supplier for information about how to do this WATER CHEMISTRY The hydrotherapy spa comes with a starter chemical pack for maintaining the water in the spa See TEST ING AND TREATING THE WATER on page 11 Additional chemicals can be purchased at a pool and spa supply store CAUTION The chemicals used to maintain the pH balance of the water and to sanitize the water can be dangerous Always follow these basic guide lines when handling the chemicals 1 Always read and follow the directions on the label unless directed to do otherwise 2 Never mix different chemicals 3 Do not exceed the recommended amounts of chemicals follow the directions on the label closely 4 Keep all chemicals out of the reach of chil dren and pets 5 Keep all containers closed tightly when not in use 6 Never add water to the chemicals always add the chemicals to the water as directed 7 Always store chemicals in a cool dry place MAINTAINING THE PROPER PH BALANCE The pH factor is a measure of relative acidity or alka linity in the water It is measured on a scale of 1 to 14 Pure water has a value of 7 which is neutral Any value above 7 is alkaline and any value below 7 is acidic You should maintain a slightly alkaline pH level between 7 2 and 7 8 in the RENEW 207 Severe problems can occur when the pH balance is not maintained withi
Download Pdf Manuals
Related Search