IBM 6736-HB0 User's Manual
Contents
1. Switch on your monitor by pushing and releasing the power switch marked 0 at the front of the bezel To switch off your monitor push and release the power switch again To update or install device drivers follow the instructions in the Device Driver Installation section on page 9 If you are using the analog connector run Image Setup by following the instructions in the Automatic Image Setup section on page 12 Device Driver Installation ENGLISH Installing the device driver in Windows 95 or Windows 98 This section must be completed before continuing with the Windows 95 or Windows 98 Image Setup on page 12 OnLCD monitors unlike L CRTs a faster refresh rate does not improve display quality For optimal performance use either 1600 x 1200 at a refresh rate of 60Hz or 640 x 480 at a refresh rate of 60Hz To install the device driver in Microsoft Windows 95 or Windows 98 do the following You must download files from the User s Guide and Installation Files CD to use the Plug and Play feature in Windows 95 or Windows 98 Note 1 Turn off the computer and all attached devices 2 Ensure that the monitor is connected correctly 3 Turn on the monitor and then the system unit Allow your computer to start the Windows 95 or Windows 98 operating system Your computer s Plug and Play code might warn you that your system hardware has changed This means that it has detected your new monitor for the2. Color Monitor A L200p SE User s Guide First Edition February 2003 Note For important information refer to the Monitor Safety and Warranty manual that comes with this monitor Contents Saiely Read IESE lt a coat a aaa ia Doua ala gaina iii i aa it i 2 Setting Up TNS Monitor nina sa irina b sai anca daia ia naiba ada 3 Product DSS e UL ace aan era nea aie ar a adi a ie ala 3 Handling INSINIGUG NS sti a tat d ide at 3 Workplace preparation ic acc oua aaa aceata dada dala d da otet Sia 4 Adjusting the Monitor Position css nete cn cai a a ae ia eta 5 Working Practices sn 6 Caring for your Monitor iia 6 Connecting your MONITO xn an ri teen n ea n a n e e a 7 Switching on your Monitor oana aia ii te i it it 8 Device Driver Installation rr sati aaa alai 9 Windows 95 98 snm anina amicii an leida 9 Veloen TA 10 WINGOWS a ARN RR RI RE RE NI IRI IN dis 11 Automatic e CT i i i iu 12 Image SOUL za ei au lait a ia aaa at ala at 12 Image Setup for DO area inel it 13 Image Setup for Windows 95 Windows 98 Windows 2000 Windows NT Windows Me or Windows XP n cei cacao one amica ap n i de ar ie 14 Manual Image Sell iaca isi a iama aa a n d n ia aia ni ii 15 Adjusting Your LCD e e LE 16 User COMO S cect aan aaa i Cl ela a Dea ua nai 16 On screen display OSD Controls EEN 17 Further Information ns oi a ai mai iti a ai aia ini dia A aaa i dai 20 Display REENEN 20 Power Management 21
3. IBM may use or distribute any for the information you supply in any way it believes appropriate without incurring any obligation to you Any references in this publication to non IBM Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites The materials at those Web sites are not part of the materials for this IBM product and use of those Web sites is at your own risk 27 28 Trademarks The following terms used in this publication are trademarks or service marks of the IBM Corporation in the United States other countries or both HelpCenter IBM ENERGY STARE is a U S Govt registered trademark Microsoft Windows and Windows NT are trademarks of Microsoft Corporation in the United States other countries of both Other company product and service names may be trademarks or service marks of other Copyright International Business Machines Corporation 2003 All rights reserved
4. Note VESA timings are as detailed in the VESA Display Monitor Timing Specification Version 1 0 Revision 0 8 Dated 09 17 98 20 The display mode the monitor uses is controlled by the computer Therefore you should refer to your computer documentation for details on how to change display modes The image size position and shape may change when the display mode changes This is normal and the image can be readjusted using IMAGE SETUP and the monitor controls Unlike CRT monitors which require a high refresh rate to minimize flicker TFT technology is inherently flicker free If possible configure your computer for 1600 x 1200 addressability at 60Hz vertical refresh rate For the display modes listed below the screen image has been optimized during manufacture Factory Set Display Modes Addressability Refresh Rate Horizontal Frequency 640 x 480 60 Hz 31 5 kHz 640 x 480 75 Hz 35 0 kHz 640 x 480 85 Hz 37 5 kHz 640 x 350 70 Hz 31 5 kHz 720 x 400 70 Hz 31 5 kHz 800 x 600 60 Hz 35 2 kHz 800 x 600 75 Hz 37 9 kHz 800 x 600 85 Hz 48 1 kHz 832 x 624 75 Hz 49 7 kHz 1024 x 768 60 Hz 48 4 kHz 1024 x 768 75 Hz 60 0 kHz 1024 x 768 85 Hz 68 7 kHz 1152 x 870 75 Hz 68 7 kHz 1152 x 900 66 Hz 61 8 kHz 1280 x 1024 60 Hz 64 0 kHz 1280 x 1024 75 Hz 80 0 kHz 1600 x 1200 t 60 Hz 75 0 kHz 1600 x 1200 tt 75 Hz 93 7 kHz t Recommended tt D sub Analog only ENGLISH
5. Power Management To benefit from power management the monitor must be used in conjunction with a computer that implements the Video Electronics Standards Association VESA Display Power Management Signaling DPMS Standard The power management feature is invoked when the computer recognizes that you have not used your mouse or keyboard for a user definable period There are several states as described in the table below As an ENERGY STAR 2000 Partner IBM has determined that this product meets the ENERGY STAR 2000 guidelines for energy efficiency For optimal performance switch off your monitor at the end of each working day or whenever you expect to leave it unused for long periods during the day Power Restoring State Indicator Screen Operation Compliance On Steady green Normal Active off Steady amber Blank Preas AREY of ENERGY move the mouse STAR 2000 There may be a slight delay before the picture reappears Product Disposal The fluorescent lamps in the liquid crystal display contains a small amount of mercury Dispose of it as required by local ordinances and regulations 21 Troubleshooting 22 If you have a problem setting up or using your monitor you may be able to solve it yourself Before calling your retailer or IBM try the suggested actions that are appropriate to your problem software on your computer Press the to swit
6. Take regular breaks Vary your posture stand up and stretch occasionally as prolonged use of computer workstations can be tiring Back Sit back in your chair and use the backrest Hands Adjust the seat height so that your forearms are approximately horizontal and your wrists are straight when using the keyboard Your upper arms should be relaxed with your elbows near your body Use a light touch on the keyboard keeping your hands and fingers relaxed Allow a space in front of the keyboard to rest your wrists when not typing Consider using a wristpad Eyesight Working with monitors in common with any prolonged close work can be visually demanding Look away from the screen periodically and have your eyesight checked regularly Screen settings Set the screen brightness and contrast to a comfortable level You may have to adjust these settings as the lighting changes during the day Many application programs let you select color combinations which can help you to view in comfort See the User controls section on page 16 for more information Caring for your Monitor Be sure to turn off the power before you perform any maintenance on the monitor Clean your monitor as follows e Gently wipe the covers and the screen with a soft cloth Do not use solvents or abrasives e Remove finger marks and grease with a damp cloth and mild detergent e Never use flammable cleaning materials to clean your IBM monitor or any other elec
7. button for 10 seconds the message Menu is Unlocked will appear 16492 Switch between input signals On screen display OSD controls The LCD monitor needs l time to become thermally stable the first time you turn it on each day Thus to achieve more accurate adjustments for parameters allow the LCD monitor to warm up be On for at least 15 minutes before making any screen adjustment menu Initial appearance of OSD o uage Brightness Contrast main menu Brightness Contrast a Brightness Adjusts overall screen brightness e ENGLISH The settings adjustable with the user controls are viewed through the On Screen Display OSD Press the enter button to display the main OSD OSD functions oe Control and OSD Icon Description sub menu s Adjustments ZK Xt Adjusts brightness e TI Brightness Brightness Contrast 9 Adjusts contrast 9 9 Contrast Is not available with a digital input gt O O Moves the screen left and right az Ai 4 Is not available with a digital input s Image Horizontal i ee rae Position Position Moves the screen up and down Pe AZ Vertical Is not available with a digital input gt Position E gt 18 OSD Icon Description Sub menu s Controls and Adjustments Cd Automatic Ey Image Setup The IMA
8. Prod ct DISS EA sisi 21 TEOUDIGSIOOUING iniciara ii 22 Help and Service IMMONMAtlOn siii ib is 24 SpecificatlohS ion oi 25 Service TGF ALON ice in stein aia iii an ai i ini daia 26 Notices and Trademarks ni i ni iia 27 ENGLISH Kit Safety Read first Before installing this product read the Safety Information Avant d installer ce produit lisez les consignes de s curit Vor der Installation dieses Produkts die Sicherheitshinweise lesen Mpv eyKataotroete To Tpoi v aut SiaBdote TIG MANPO opies aop eia safety information MMVI MANI NR 1878 NT 1931 172000 392 A term k telep t se el tt olvassa el a Biztons gi el r sokat Prima di installare questo prodotto leggere le Informazioni sulla Sicurezza Antes de instalar este produto leia as Informa es de Seguran a L s s kerhetsinformationen innan du installerar den h r produkten Prije instalacije ovog produkta obavezno pro itajte Sigurnosne Upute Les sikkerhetsinformasjonen Safety Information f r du installerer dette produktet Przed zainstalowaniem tego produktu nale y zapozna si z ksi k Informacje dotycz ce bezpiecze stwa Safety Information Tlpen aa ce MHCTAJIMPA OBO NPONYKT MpOYHTAjTE nnpopmanujara 3a Ge3OeqHOCT Pred in tal ciou tohto zariadenia si pe itaje Bezpe nostn predpisy Pred namestitvijo tega proizvoda preberite Varnostne informacije Ennen kuin asennat t m n tuotteen lue turvaohjeet kohdasta
9. Safety Information P ed instalac tohoto produktu si prect te p ru ku bezpe nostn ch instrukc PERERA 2 gu WT Safety Information 4a i FRA ZI gt RAMA RARA e aul la be aaa za Las sikkerhedsforskrifterne fer du installerer dette produkt RATA OM ERE Big CEE M3 SAol AO erai BLE ALYN Antes de instalar este producto lea la informaci n de seguridad Antes de instalar este produto leia as Informa es de Seguran a Nepeg ycTaHOBKO Mpo 1ykTa MpO4TUTE UHCTPyYKUMM MO TexHuke 6e3onacHocTu Lees voordat u dit product installeert eerst de veiligheidsvoorschriften ENGLISH Setting up the monitor Product Description This monitor requires a computer with a suitable on board sub system or Video Adapter card that can support UXGA 1600 x 1200 SXGA 1280 x 1024 XGA 1024 x 768 SVGA 800 x 600 or VGA 640 x 480 at 60Hz In addition to your monitor your option package includes the following User s Guide and Installation Files CD e Monitor Safety and Warranty Information Manual L200p Color Monitor Quick Setup Guide Power Cord L200p Color Monitor Analog Interface Cable Attached to Monitor Handling Instructions Do not support the monitor within the screen area The Liquid Crystal Display is glass and can be damaged by rough handling or excessive pressure 1 Lift the monitor by placing your hands where indicated below 2 Before using your monitor for
10. maximum refresh rate and corresponding Color Matching Profiles PSSS 9 ENGLISH Installing the device driver in Windows XP This section must be completed before continuing with the Windows XP Image Setup on page 12 On LCD monitors unlike l CRTs a faster refresh rate does not improve display quality For optimal performance use either 1600 x 1200 at a refresh rate of 60Hz or 640 x 480 at a refresh rate of 60Hz To install the device driver in Windows XP do the following You must download files from the User s Guide and Installation Files CD to use the Plug and Play feature in Windows XP Note 1 Turn off the computer and all attached devices 2 Ensure that the monitor is connected correctly 3 Turn on the monitor and then the system unit Allow your computer to start the Windows XP operating system 4 Open the Display Properties window by clicking Start Settings Control Panel and then double clicking on the Display icon 5 Click the Settings tab 6 Click the Advanced button 7 Click the Monitor tab 8 Click the Properties button 9 Click the Driver tab 4 0 Open the Hardware Update Wizard window by clicking on Update Driver and then click the Next button 11 Select Install from a list or Specific location Advanced and then click the Next button 12 Insert the Monitor CD into the CD drive and click the Have Disk button 13 Click OK 14 Ensure that the CD drive letter is s
11. on the computer If the message CHECK SIGNAL CABLE is displayed or if nothing is displayed check e that the video interface cable is not connected properly e the correct video adapter card is not installed e the correct supported display mode is selected for your computer 2 Wait approximately 15 minutes until the monitor warms up 3 Insert the User s Guide and Installation Files CD into the computer CD ROM drive 4 Display the command prompt screen of the DOS full screen display 5 Type d change the drive letter to match your CD ROM drive if it is not drive D 6 Type TESTPATD and press ENTER 7 Select from the screen the number for the color or text mode you want to set up 8 Select from the screen the number for the video mode you want to set up You can repeat this process for as many of the color and video modes as you need 9 When the dot pattern appears press the 1 button at the bottom of the monitor This activates the AUTO SETUP procedure which will optimize the display settings with the provided dot patterns The screen will momentarily turn black while auto adjustment proceeds When finished the Image Setup message disappears and the screen returns to a normal display 11 To clear the Image Setup test pattern press the ESC key on your keyboard 12 Type Exit at the command prompt to return to Windows 10 If you use other operating systems perform the appropriate Auto Setup for those system
12. the first time remove the clear protective film from the front of the screen 3 Before adjusting your monitor for the first time remove the locking clip on rear of the stand Carefully hold the screen of the monitor and then squeeze at arrows shown to remove Figure A SELLELE E Qu Wi E go E Figure A Workplace Preparation This section gives advice Height h houl e edi ain ie fs tie ee up Position the monitor so that the top of the screen is slightly below your eye your monitor level when you sit at your workstation Orientation Choose a position that gives the least reflection from lights and windows usually at a right angle to any windows Positon the monitor directly in front of you so that you do not have to twist your body to use it Tilt the monitor to a comfortable viewing angle ENGLISH Adjusting the Monitor Position E With the IBM Flat Panel A Monitor you can adjust its position in various ways for Viewing Angle maximum comfort You can tilt the screen forward and backward as shown below in Figure A Swivel You can swivel the screen to the left or the right as shown below in Figure A Height You can adjust height of the screen as shown below in Figure B Figure A Figure B Working Practices This section gives advice on how you can work comfortably and reduce fatigue Rest
13. use a supported Penner e indicator is outside the display mode uormanon flashing green range of the section on every 0 5 monitor page 20 second CHECK The monitor is e Check that the signal cable c SIGNAL CABLE not receiving a is firmly connected to the onnecting message is video signal computer your monitor shown and e Check that no pins are bent section on power indicator in the signal cable connector Page 7 is steady amber Image appears There are noises Select IMAGE SETUP menu User to be smeared in the video in the OSD Then select Controls signal MANUAL to adjust CLOCK section on PHASE settings page 18 Image appears The color setting e Adjust the Color settings aud to be discolored may be incorrect Controls section on page 18 A few dots are A small number of missing discolored or lighted dots may be missing present on the screen which is an intrinsic characteristic of the discolored or TFT LCD technology and is not an LCD defect inappropriately lighted 23 ENGLISH Help and Service Information If possible stay by your l computer Your Technical Support Representative may wish to go through the problem with you during the call More help late breaking news and details of the latest accessories for these products may be found on the worldwide web at http www pc ibm com us accessories 24 If you are unable to correct the problem yourself you may see
14. 0Hz or 640 x 480 at a refresh rate of 60Hz 10 To install the device driver in Microsoft Windows 2000 Professional or Microsoft Windows Millennium Edition Me do the following You must download files from the User s Guide and Installation Files CD to use the Plug and Play feature in Windows 2000 or Windows Me Note 1 Turn off the computer and all attached devices 2 Ensure that the monitor is connected correctly 3 Turn on the monitor and then the system unit Allow your computer to start the Windows 2000 or Windows Me operating system 4 Open the Display Properties window by clicking Start Settings Control Panel and then double clicking on the Display icon Click the Settings tab Click the Advanced button Click the Monitor tab Click the Properties button Click the Driver tab 0 Open the Upgrade Device Driver Wizard window by clicking on Update Driver and then click the Next button 11 Select Display a list of the known drivers for this device so that can choose a specific driver and then click the Next button 12 Insert the Monitor CD into the CD drive and click the Have Disk button 13 Click OK 14 Ensure that the CD drive letter is selected and then select the DRIVERS folder 15 Select IBM L200p monitor and click OK The files will be copied from the CD to your hard disk drive 16 Close all open windows and remove the CD 17 Restart the computer The system will automatically select the
15. GE SETUP function is used to adjust the level of noise in the video signal which causes horizontal lines or areas on the screen where the image appears to be unstable and jitters or shimmers This can be done automatically or manually e Itis not applicable to digital input If AUTO is selected the image will automatically adjust To adjust the focus of the 20 If manual is selected the user will go Clock to the manual adjustment screen Phase display This item allows Save you to remove any Manual horizontal noise and clear or sharpen the image of characters Select the COLOR MODE you find most Preset E comfortable or fine tune the colors using 6500K the CUSTOM menu if necessary Pink White 7200K Image Color s Proportia Normal White e 9300K Blue White Custom e Red Increases or decreases redness e Green Increases or decreases greenness e Blue Increases or decreases blueness e Save This function displays the image in its Off 1 1 image at normal size a Scaling original size or enlarged size so as to fit in the full screen of the LCD panel On Expand image enlarged to fill screen ENGLISH OSD Icon Description Sub menu s Controls and Adjustments Image Properties 16492 Input Signal Use this button to make the analog or digital connector active This feature is used when two computers are connected to the monitor The d
16. ch between analog and digital mode If the panel is the wrong mode for the signal being provided the monitor appears to go into sleep mode Problem Possible Suggested Action Reference Cause Screen is No power to Ensure that the electrical outlet Connecting blank and monitor and the monitor are both your power switched on Monitor indicator is off Check that the power cord section on is firmly plugged into the page 7 electrical outlet and the power supply unit If the power cord plug has a removable fuse replace it Try another power cord Try another electrical outlet Check the power connection at the back of the panel Screen is blank Brightness Adjust brightness and contrast User and power and Contrast controls indicator is may be too section on steady green low page 17 Screen is blank The monitor is Press any key on the keyboard Power and power in the Power or move the mouse to restore Management indicator is Management operation section on steady amber Standby state Check the Power Management page 21 For image problems you Ll may want to run IMAGE SETUP again before consulting to this section In most cases IMAGE SETUP can fix the problems See Autometic Image Setup for the computer on page 12 for details Problem cL Suggested Action Reference Screen is blank Display mode of e Reconfigure key on the and power the computer is computer to
17. e the Right Arrow button to select to MANUAL Press the OK button twice to select COLOK 6 Use the Arrow buttons to manually adjust to correct as much as possible for jitter or noise in the image Press OK button 7 Press OK and use Arrow buttons to adjust PHASE press OK Press OK again to Save and Exit Then press Cancel button gt twice to exit OSD You have completed the monitor setup 15 ENGLISH Adjusting Your LCD Monitor User controls 2 The image is already l optimized for many display modes however the user controls can be used to adjust the image to your liking The settings are saved l after adjustment and when exiting the OSD and will be effective thereafter 16 USER CONTROL FEATURES Icon Monitor controls O Switches the monitors on and off l Display main OSD menu and selects highlighted menu item Moved the cursor to highlight icons or make adjustments Exits from current OSD menu Icon Direct Access Functions CH Bring up Brightness adjustment Executes automatic image setup CONTROLS LOCK UNLOCK This feature allows you to secure the current control settings while allowing the user to adjust Brightness so that they cannot be inadvertently changed Push and hold the enter button for 10 seconds the message Menu is Locked appears You can unlock the OSD controls at any time by pushing the enter
18. efault setting is analog DjAnalog Analog 2 1 Digital Options O Information Display the detailed information of mode model name and microcode O The language chosen affects only the language of the OSD e English e Francais Select one of the Five language to use for Italiano Menu Language the OSD e Deutsch It has no effect on any software running Espa ol on the computer Changes the position of the OSD on the Default move at center on the E screen screen Menu Position Custom Horizontal Vertical Save Reset should return all available Cancel R functions apart from language which Reset should not change unless adjusted via Factory Default the LANGUAGE menu to their factory presets Tr Change button repeat rate and menu Button Adjusts respondence time out setting repeat rate speed of button e Off Accessibility e Default e Slow Menu time out Adjusts the length of time for which the menu will stay on the screen before it disappears Exit Exits from current OSD menu 19 Further Information Display modes 2 If your computer has l previously been used with a CRT monitor and is currently configured to a display mode outside the range that the Flat Panel monitor can display you may need to re attach the CRT monitor temporarily until you have reconfigured the computer preferably to 1600 x 1200 at 60Hz
19. elected and then select the DRIVERS folder 15 Select IBM L200p monitor and click OK The files will be copied from the CD to your hard disk drive 16 Close all open windows and remove the CD 17 Restart the computer The system will automatically select the maximum refresh rate and corresponding Color Matching Profiles 11 Automatic Image Setup Co Image Setup Before carrying out this section it is very important that the correct monitor drivers have been installed See pages 9 and 11 2 The Setup Utility included L on the setup CD displays a test pattern of dots It does not replace or modify the display drivers The Image Setup l instructions require the monitor to be warmed up for 15 minutes This is not required for normal operation 2 If your computer does not l run with the setup CD Shipped with the monitor refer to Manual Image Setup on page 15 The Image Setup process l only applies to the current screen mode When a new mode is selected repeat this section to reset the monitor 12 For digital input image setup is not required When you first use your monitor you must perform Auto Setup for analog input If you are using digital input continue with the instructions on page 6 This procedure sets up your monitor to process the video signals from your computer without image discoloration or smearing After you perform Auto Setup the settings are stored and used each time you turn on t
20. els max Vert Addressability 1200 lines max Clock Frequency 130 MHz Digital 205 MHz Analog Sync Input Type Analog Separate Composite SOG Digital DVI 1 0 Communications VESA DDC E DDC Supported Display Standard modes IBM VESA MAC Modes Horiz Frequency Vert Frequency Digital 31 75 kHz Analog 31 94 kHz 56 85Hz Environment Temperature Operating Storage Shipping Humidity Operating Storage Shipping 10 to 35 C 50 to 95 F 20 to 60 C 4 to 140 F 20 to 60 C 4 to 140 F 10 to 80 5 to 95 5 to 95 25 ENGLISH Service Information The following parts are for use by IBM service or IBM authorized dealers to support the customer warranty Parts are for service use only Model Type 6736 Description Video Color MTM 31P9263 FRU Monitor Hybrid SB 6736 HBO 31P9264 FRU Stand Hybrid SB 6736 HBO 31P9265 FRU Video Cable Analog Black 6736 HBO 26 ENGLISH Notices and Trademarks This section contains information on notices and trademarks Notices IBM may not offer the products services or feature discussed in this document in all countries Consult your local IBM representative for information on the products and services currently available in your area Any reference to an IBM product program or service is not intended to state or imply that only that IBM product program or service may be used An
21. first time 4 Open the Display Properties window by clicking Start Settings Control Panel and then double clicking on the Display icon 5 Click the Settings tab e If you are using Windows 95 6 1 Click the Change Display Type button 2 Click the Change Monitor Type button e If you are using Windows 98 6 1 Click the Advanced button 2 Click the Monitor tab 3 Open the Upgrade Device Driver Wizard window by clicking on Change button and then select the Next button 4 Click Display a list of the known drivers for this device so that can choose a specific driver and then select the Next button 7 Insert the User s Guide and Installation Files CD into the CD driver and click the Have Disk button 8 Click OK 9 Ensure that the CD drive letter is selected and then select the DRIVERS folder 10 Select IBM L200p monitor and click OK The files will be copied from the CD to your hard disk drive 11 Close all open windows and remove the CD 12 Restart the computer The system will automatically select the maximum refresh rate and corresponding Color Matching Profiles Installing the device driver in Windows 2000 or Windows Me This section must be completed before continuing with the Windows 2000 Windows Me Image Setup on page 12 On LCD monitors unlike l CRTs a faster refresh rate does not improve display quality For optimal performance use either 1600 x 1200 at a refresh rate of 6
22. he monitor In order to optimize the displayed image a set up utility is provided on the IBM Monitor CD Operation of this utility is dependent on the operating system on your computer You may choose to run IMAGE SETUP for each operating system that you use This means that if you sometimes use your monitor while running any version of Windows and sometimes also use it from within DOS not a DOS window you must run IMAGE SETUP for both Windows and DOS You may run versions of IMAGE SETUP in any order Before you begin IMAGE SETUP for your computer make sure the computer video mode is set in the range of the supported screen resolution shown in the table on page 20 You should perform IMAGE SETUP for each screen mode you use ENGLISH Image Setup for DOS If the monitor is in standby mode STANDBY ON it may automatically turn off while you are waiting for it to warm up If this happens switch off the monitor and switch it on again after a few seconds E Ifyou are using PC DOS V l change to U S mode by typing CHEV US and pressing ENTER at the command prompt The size and diversity of the l dot pattern varies with the screen resolution gt Ifthe screen flickers repeat L the setup several times until the flicker is minimized or adjust it manually by following refer to Manual Image Setup on page 15 To set up the monitor automatically in DOS do the following 1 Turn on the monitor first then turn
23. k further help as follows Call the IBM HelpCenter In the U S A and Puerto Rico call 1 800 772 2227 In Canada Toronto Only call 416 383 3344 In Canada all other call 1 800 565 3344 In other countries contact your dealer retailer or other IBM authorized Servicer Before calling please have available as much of the following information as possible Model and serial number from the label on your monitor Purchase receipt Description of problem Computer type and model System configuration hardware fitted etc System BIOS version number Operating System and version number Display driver version number O Dm Jm mF a 3 Video Adapter Type Specifications E Power consumption figures are for the monitor and the power supply combined This color monitor Type model 6736 HB0 uses a 20 1 inch TFT LCD Height 391 7 mm 15 42 inch Min 471 7 mm 18 57 inch Max Width 467 5 mm 18 41 inch Depth 259 0 mm 10 2 inch Weight With Stand 8 35 kg 18 41 lbs Image Viewable Image Size 20 1 inch 510 54 mm Maximum Height 306 mm 12 05 inch Maximum Width 408 mm 16 04 inch Pixel Pitch 0 255 mm H x 0 255 mm V Power Input Supply Voltage 100 240V ac 60 50 3Hz Rated Current 1 24 Power Normal Operation lt 65 W Consumption Active off lt 3W Off lt 1W Video Input Input Signal Analog 75 ohm 0 7V Digital DVI 1 0 Horiz Addressability 1600 pix
24. s using instructions given in Image Setup Windows 95 Windows 98 Windows NT Windows 2000 Windows Me or Window XP on page 14 13 Image Setup for Windows 95 Windows 98 Windows NT Windows 2000 Windows Me or Windows XP If the monitor is in standby l mode STANDBY ON it may automatically turn off while you are waiting for it to warm up The size and diversity of the dot pattern varies with the screen resolution 14 To set up the monitor automatically in Windows 95 Windows 98 Windows NT Windows 2000 Windows Me or Windows XP do the following 1 Turn on the monitor first then turn on the computer If the message CHECK SIGNAL CABLE is displayed or if nothing is displayed check e that the video interface cable is not connected properly e the correct video adapter card is not installed e the correct supported display mode is selected for your computer 2 Wait approximately 15 minutes until the monitor warms up 3 Drag the icon bar and tool bar if they are displayed to the bottom of the screen Insert the User s Guide and Installation Files CD into the computer CD ROM drive 5 Check the operating system installed on your computer and follow the instructions from the table below Operating system installation steps Operating System Step1 Step2 Step3 Windows 95 Windows 98 Type EATESTPAT change the Windows 2000 Select Select drive letter to match your CD ROM Windows NT START RUN dri
25. trical apparatus ENGLISH Connecting your Monitor Be sure to read the Safety 1 Turn off your computer and all attached devices Next unplug the Information located in the j ower cord s to your computer and all attached devices Monitor Safety and Warranty p y H Information Manual before 2 Connect the signal cable carrying outis procsaure The analog signal cable is already connected to your monitor g The analog connector is the blue connector When connecting the analog signal cable Figure A Connect the free end of the attached signal cable to the 15 pin Monitor port on the computer and tighten screws DIALS RIAL LL AS OCULAR Figure A H connecting a DVI D digital signal cable Figure B Connect one end of the monitor signal cable to the white connector on the rear panel of the monitor Connect the other end to the white connector on the rear panel of the computer and tighten the screws Cable not supplied Optional Figure B 7 3 Connect the power cord to the monitor and then plug the power cord into a properly grounded outlet Next reconnect the power cord s to your computer and all attached devices Switching on your Monitor 1 2 Switch on your computer Switch on the monitor power source by pushing the power switch A on side rear panel of the monitor See Figure B
26. ve if it is not drive D and press Windows Me or ENTER Windows XP 6 When the dot pattern appears press the O0 button at the bottom of the monitor This activates the IMAGE SETUP procedure which will optimize the display settings with the provided dot patterns The screen will momentarily turn black while auto adjustment proceeds 7 When finished the Image Setup message disappears and the screen returns to a normal display 8 Toclear the Image Setup test pattern press the ESC key on your keyboard You have completed the monitor setup for Windows If you are using the DOS operating system go to Image Setup for DOS on page 13 Manual Image Setup If the monitor is in standby mode STANDBY ON it might automatically turn off while you are waiting for it to warm up Normally you can complete the setup procedure using Automatic Image Setup however if your screen image is still distorted after you perform Image Setup or the setup CD does not run on your system perform MANUAL IMAGE SETUP To manually adjust the image setting do the following 1 Have your monitor turned on for about 15 minutes until the monitor warms up Display the image you most frequently use on the screen Press the OSD Enter button at the bottom of the monitor to display the initial OSD menu 4 Use the Right Arrow button to select the IMAGE SETUP icon CO and press the OSD Enter button to access the function 5 Us
27. y functionally equivalent product program or service that does not infringe any IBM intellectual property right may be used instead However it is the user s responsibility to evaluate and verify the operation of any non IBM product program or service IBM may have patents or pending patent applications covering subject matter described in this document The furnishing of this document does not give you any license to these patents You can send license inquiries in writing to IBM Director of Licensing IBM Corporation North Castle Drive Armonk NY 10504 1785 U S A The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent with local law INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Some states do not allow disclaimer of express or implied warranties in certain transactions therefore this statement may not apply to you This information could include technical inaccuracies or typographical errors Changes are periodically made to the information herein these changes will be incorporated in new editions of the publication IBM may maker improvements and or changes in the product s and or the program s described in this publication at any time without notice
Download Pdf Manuals
Related Search