Husqvarna HA 110 User's Manual
Contents
1. hand guard is not damaged Replace the guard if damaged HA 110 Weekly maintenance 1 Fill the gear housing with grease This should be carried out approximately every 20 working hours 2 Check that the screws that hold the blades together are correctly tightened Technical data Technical data HA 110 Weight Weight Lbs kg 2 0 Blades Length mm 550 Blade speed cuts min 4184 HA 850 2 3 550 4184 English 11 1140026 20 UAT TMNT TN aaa We hope you find the links below useful For further gardening information visit www GardenResources co uk gsn cutters cullers Stusticutlers mowers chainsaws spreaders Garden tractors EE vacuums Hayter lawn Hedge cutters Hedgecutters mowers chainsaws cutters strimmers ates mowers tractors mowers tractors Mowers Chainsaws Spreaders EE Mowers PATA Cutters Strimmers Leaf Blowers Cute Mowers Heaters Heaters Covers Heaters Heaters Heaters Patio Heaters Heaters Covers fe a UOO Gardening Gifts Mowers Also See Gardening Tools Direct for lawn mowers brush cutters chainsaws Gardening Supply for patio heaters lawn mowers chainsaws Garden Tractor for lawn tractors and ride on mowers2. Operator s manual Manual d utilisation Manual de instrucciones Hedge Trimmer Attachment HA 110 HA 850 Compl ment Taille haie HA 110 HA 850 Tijeras cortasetos suplemento HA 110 HA 850 GB FR ES KEY TO SYMBOLS Symbols WARNING Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury It is extremely important that you read and understand the contents of this operator s manual gt Please read the operator s manual carefully and make sure you understand the instructions before using the machine LI Always wear e Approved hearing protection e Protective goggles or a visor This product is in accordance with applicable EC directives Cutting tool Do not touch the tool without A first switching off the engine This machine is not electrically insulated If the machine touches or comes close to high voltage power lines it could lead to death or serious bodily injury Electricity can jump from one point to another by arcing The higher the voltage the greater the distance electricity can jump 2 Ano OS Electricity can also travel through Ti branches and other objects especially if they are wet Always keep a distance of at least 10 m between the machine and high voltage power lines and or any objects that are touching them If have to work within this safe distance you should always contact the relevant power company to make sur
3. attachment always stops when the engine is idling e Only use the machine for the purpose it was intended for e Make sure that the handle and safety features are in good working order Never use a machine that lacks a part or has been modified outside its specifications 10 English MAINTENANCE Gear housing le There are three grease nipples on the gear housing Use a grease gun to top up with grease This should be carried out approximately every 20 working hours Use Husqvarna special grease part no 503 98 96 01 CAUTION The gear housing must not be filled completely with grease The grease expands as the machine heats up during operation If the gear housing was completely filled with grease it could damage the seals and lead to leakage of grease The grease in the bevel gear does not normally need to be changed except if repairs are carried out Cleaning and lubrication slo After you have used the machine clean any resin and plant residue from the blades using cleaning agent 531 00 60 75 UL22 Always lubricate the blade bars with special grease part no 531 00 60 74 UL 21 before use Maintenance schedule Below you will find some general maintenance instructions If you need further information please contact your service workshop Daily maintenance 1 Check that the blades do not move when the engine is idling or when the choke is in the start throttle position 2 Check that the
4. e the power is switched off before you start work 0m 30ft y N This machine can be dangerous The operator of the machine must ensure while working that no persons or animals come closer than 15 metres Arrows which show limits for handle positioning Always wear approved protective gloves Wear sturdy non slip boots 2 English Noise emission to the environment according to the European Community s Directive The machine s emission is specified in chapter Technical data and on label Lwa dB Other symbols decals on the machine refer to special certification requirements for certain markets Switch off the engine by moving the stop switch to the STOP position before carrying out any checks or maintenance Always wear approved protective gloves Regular cleaning is required Visual check Protective goggles or a visor must be worn CONTENTS Contents Note the following before starting KEY TO SYMBOLS Husqvarna AB has a policy of continuous product SVINDOLS sins 2 development and therefore reserves the right to modify the CONTENTS design and appearance of products without prior notice COMICS dust iii 3 Long term exposure to noise can result in permanent hearing Note the following before starting coocononocos 3 impairment So always use approved hearing protection SAFETY INSTRUCTIONS Machine s safety equipment cccccccccccccnccccnnnconnnicnnnnnos 4 WARNING Unde
5. machine s safety equipment its purpose and how checks and maintenance should be carried out to ensure that it operates correctly See the What is what section to locate where this equipment is positioned on your machine The life span of the machine can be reduced and the risk of accidents can increase if machine maintenance is not carried out correctly and if service and or repairs are not carried out professionally If you need further information please contact your nearest service workshop WARNING Never use a machine that has faulty safety equipment Carry out the inspection maintenance and service routines listed in this section Hand guard HA 110 The hand guard prevents hands from coming into contact with the moving blades for example if the operator loses grip on the front handle Blade guard HA 110 The blade guard A is intended to protect against any part of the body coming into contact with the blades B 4 English Checking maintaining and servicing the machine s safety equipment WARNING Never use a machine with faulty safety equipment The machine s safety equipment must be checked and maintained as described in this section If your machine fails any of these checks contact your service agent to get it repaired WARNING Always stop the engine before doing any work on the cutting attachment This continues to rotate even after the throttle has been released Ensu
6. r no circumstances may the Checking maintaining and servicing the machine s design of the machine be modified without Safety EQUIPMENT c cccooccnccnccnccocnnnnonnnonnnnnonononononnnnnonononanos 4 the permission of the manufacturer Always Safety instructions when using the hedge trimmer 5 use genuine accessories Non authorized WHAT IS WHAT modifications and or accessories can result in serious personal injury or the death of the 2 What is what on the hedge trimmer attachment HA operator or others 2 ee ee ee SM Ree ere een eee ee 7 What is what on the hedge trimmer attachment HA A ces cacao AEE ESE A 8 WARNING This accessory may only be used ASSEMBLY together with the intended clearing saw Fitting the hand guard and loop handle HA 110 9 trimmer see under heading Approved Fitting the cutting head cccccccccccccnnnonnnoconononoccnonnnos 9 accessories in chapter Technical data in the STARTING AND STOPPING machine s Operator s Manual Check before Starting ooccccccococonconcccononanonnnnnonanenons 10 The machine is only designed for cutting branches and twigs MAINTENANCE Gear TOUS IG tt tao ticas 11 Cleaning and lubrication coccooccncnncconnnnncnnnonnononos 11 Maintenance schedule occcoooonccnccccccncnccnccnnnnncnonononnnons 11 TECHNICAL DATA MeGhiniGal data riada 11 English 3 SAFETY INSTRUCTIONS Machine s safety equipment This section describes the
7. re that the cutting attachment has stopped completely and disconnect the HT lead from the spark plug before you start to work on it Hand guard HA 110 e Check that the hand guard is fitted correctly e Check that the hand guard is undamaged Blades To ensure good cutting results it is important that the contact pressure between the blades is correct The contact pressure is adjusted by turning the screws on the underside of the bar clockwise as far as they will go Then turn the screws anticlockwise a 1 4 turn Lock the screws using the locking nut on the top of the bar Check that the screws are loose enough to allow the washers under the screw heads to slide sideways When the blades are correctly adjusted the play between the blades should be 0 2 0 4 mm measured at the screws The edges of the blades are too hard to be filed Dull blades should be sharpened using a grinder Replace the blades if they are bent or damaged SAFETY INSTRUCTIONS Blade guard HA 110 e Check that the blade guard is not damaged or distorted e Replace the blade guard if it is bent or damaged Gear housing e The gear housing gets hot when the machine has been in use To avoid burning yourself do not touch the gear housing Safety instructions when using the hedge trimmer WARNING The machine can cause serious personal injury Read the safety instructions carefully Learn how to use the machine WARNING C
8. se to your body as possible to get the best balance 6 English e Make sure that the tip does not touch the ground e Do not rush the work but work steadily until all the branches have been cut back cleanly Changing the hedge trimmer angle HA 110 e Undo the knob e Press the cutting head against the ground or some other solid object until the desired angle has been obtained e Tighten the knob HA 850 e Undo the knob e Grasp the handle on the angle stop adjust to the desired angle and then tighten the knob WARNING Do not hold the cutting head when you adjust the angle The blades are sharp and you could easily cut yourself WHAT IS WHAT Husqvarna What is what on the hedge trimmer attachment HA 110 1 Cutter 7 Angle adjustment knob 2 Grease nipples 3 8 Hand guard 3 Bevel gear 9 Operator s manual 4 Blade guard 10 Transport guard 5 Front handle 11 Shaft coupling 6 Hand guard mounting screw 12 Shaft 110 mm English WHAT IS WHAT What is what on the hedge trimmer attachment HA 850 1 Cutter 6 Angle adjustment knob 2 Grease nipples 3 7 Operator s manual 3 Bevel gear 8 Transport guard 4 Front handle 9 Shaft coupling 5 Shaft 829 mm 10 Handle 8 English ASSEMBLY Fitting the hand guard and loop Fitting the cutting head handle HA 1 10 It is important that the hedge trimmer is laid on a flat surface when you fit the cutting head Otherwise
9. t English 5 SAFETY INSTRUCTIONS e Do not cut too close to the ground Stones and other objects can be thrown out e Check the working area for foreign objects such as electricity cables insects and animals etc or other objects that could damage the cutting attachment such as metal items e If any foreign object is hit or if vibrations occur stop the machine immediately Disconnect the HT lead from the spark plug Check that the machine is not damaged Repair any damage e If anything jams in the blades while you are working switch off the engine and wait until it has stopped completely before cleaning the blades Disconnect the HT lead from the spark plug Safety instructions after completing work e The transport guard should always be fitted to the cutting attachment when the machine is not in use e Make sure the cutting attachment has stopped before cleaning carrying out repairs or an inspection Disconnect the HT lead from the spark plug e Always wear heavy duty gloves when repairing the cutting attachment This is extremely sharp and can easily cause cuts e Store the machine out of reach of children e Use only original spare parts for repairs Basic working techniques e Work with a swinging action from the bottom upwards when trimming sides e Adjust the throttle setting to suit the load e When trimming a hedge the engine should always face away from the hedge e Hold the machine as clo
10. the cutting head may not be fitted straight 1 Fit the cutting head to the shaft CAUTION Make sure the drive shaft inside the shaft engages with the recess in the cutting head 1 Loosen the clutch sleeve s two mounting bolts and dismantle the clutch sleeve Fo 2 Assemble the hand guard and loop handle by screwing them together Take care to align the holes in both parts 2 Tighten the lower screw first then the upper screw 3 Slide the loop handle and hand guard onto the shaft 4 Slide the spacer into the slot in the loop handle 5 Fit the nut and screw Do not overtighten 6 Now make a final adjustment to give yourself a comfortable working position Tighten the screw CAUTION The loop handle and hand guard must not be fitted behind the arrow marked on the shaft 7 Fit the clutch sleeve and tighten the two mounting bolts English 9 STARTING AND STOPPING Check before starting e Inspect the working area Remove any objects that could be thrown out e Check the cutting attachment Never use blades that are dull cracked or damaged e Check that the machine is in perfect working order Check that all nuts and screws are tight e Check that the blade guard is not damaged or distorted HA 110 e Replace the blade guard if it is bent or damaged HA 110 e Make sure the gear housing is lubricated correctly See instructions under the heading Gear housing e Check that the cutting
11. utting tool Do not touch the tool without first switching off the engine CAUTION Please read the operator s manual carefully and make sure you understand the instructions before using the machine Personal protection e Always wear boots and other equipment described under the heading Personal protective equipment e Always wear working clothes and heavy duty long trousers e Never wear loose clothing or jewellery e Make sure your hair does not hang below shoulder level Safety instructions regarding the surroundings e Never allow children to use the machine e Ensure that no one comes closer than 15 m while you are working e Never allow anyone else to use the machine without first ensuring that they have understood the contents of the operator s manual e Never work from a ladder stool or any other raised position that is not fully secured Safety instructions while working e Always ensure you have a safe and stable working position e Always use both hands to hold the machine Hold the machine at the side of your body e Make sure that your hands and feet do not come near the cutting attachment when the engine is running e When the engine is switched off keep your hands and feet away from the cutting attachment until it has stopped completely e Watch out for stumps of branches that can be thrown out during cutting e Always lay the machine on the ground when you are not using i
Download Pdf Manuals
Related Search