Husqvarna 45-0352 User's Manual
Contents
1. Hairpin Cotter 3 32 3 Pin Clevis 1 4 x 1 1 2 Lg Screw 10 32 x 5 8 Truss Head Nut Nylock 10 32 Owners Manual Speed P a the fastest way to purchase parts WWwW speedepart com Speed P an rd the fastest way to purchase parts WWW speedepart com REPAIR PARTS Agri Fab Inc 809 South Hamilton Sullivan IL 61951 217 728 8388 2005 Agri Fab Inc www agri fab com2. Nut 10 32 Palnut Washer 7 16 Washer 5 16 Lock Washer 5 16 a MO YO A DY YO NN OMN Bowed Washer 5 16 Hair Cotter Pin Large Hair Cotter Pin Small Cotter Pin 1 8 x 3 4 Clevis Pin 3 8 x 1 2 Clevis Pin 1 4 x 1 1 8 Clevis Pin 1 4 x 1 3 4 Spacer Small Spacer Hitch Hopper Mount Clamp Angle Bracket Grip Vinyl Cap Hitch Pin Spring Hitch Pin Plastic Plug Extension Spring ASSEMBLY OF SWEEPER TOOLS REQUIRED FOR ASSEMBLY 1 Knife or Scissors 1 Screwdriver 1 Hammer 1 3 8 Open End or Box End Wrench 2 1 2 Open End or Box End Wrench 1 3 8 Open End or Box End Wrench STEP 1 REMOVE PARTS FROM CARTON 1 To protect painted parts lay them on cardboard or a mat 2 Remove the sweeper housing the loose parts and the hardware package from the carton Lay out the parts and hardware as shown on pages 3 and 4 STEP 2 INSTALL HITCH TUBES 3 The hitch tubes are stamped with a 77L for the left tube and a 76R for the right tube The sweeper housing is marked with an L on the left side and an R on the right side See figure 1 4 Holdthe left hitch tube againstthe left side of the sweeper sothatthe 77L on the tube faces away from the sweeper Attach the hitch tube using two 5 16 x 1 3 4 hex bolts and 5 16 nylock nuts Repeat for the right hitch tube but with the 76R facing in toward the right side
3. Special Spacer 78 x 1 25 x 50 Ring Retaining 594 Washer Shim 1 1 8 x 594 x 025 Nut Nylock 3 8 24 Thread Hub Cap Washer Hub Cap Bolt Hex 3 8 24 x 3 1 4 Lg Spacer Small Gear Pinion R H not shown Gear Pinion L H Bolt Hex 1 4 20 x 5 8 Lock Washer 1 4 Dust Cover Assembly Lower Hopper Tube R H Lower Hopper Tube L H Upper Hopper Tube R H Upper Hopper Tube L H Hopper Bag Wind Screen Strap Bag Frame Retainer Bag DONA NMDNMNNNANNNH HHH HHHNDHNHHHNANAH HANH NMNHNH HH HH Hb Rod Hopper Support 34 Hopper Rope Strap Height Adjustment Bracket Hitch Bracket Hitch Straight Handle Upper Height Adjustment Handle Lower Height Adjustment Tube Bag Arm Rod Hopper Bag Pivot Wheel amp Tire Ass y with bearings Wheel Bearing Bracket Hitch Pin Bolt Hex 5 16 18 x 3 Lg Bolt Hex 5 16 18 x 2 1 4 Lg Bolt Hex 5 16 18 x 2 1 2 Bolt Hex 5 16 18 x 1 3 4 Lg Cap Vinyl Washer Flat 5 16 Bolt Hex 5 16 18 x 1 Bolt Hex 5 16 18 x 1 1 4 Spring Extension Angle Bracket Lock Washer 5 16 Grip Height Adjust Spacer Hitch Hairpin Cotter 1 8 Pin Hitch Spring Hitch Pin Washer 7 16 Flat Pin Cotter 1 8 x 3 4 Lg Bolt Carriage 3 8 16 x 1 Nut Nylock 3 8 16 Bolt Cvd Hd 5 16 18 x 1 5 8 Lg Washer Bowed 1 x 32 x 06 Nut Hex 5 16 18 Thread Hopper Mount Clamp Palnut 3 8 Plug 1 4 Pin Clevis 1 4 x 1 1 8 Pin Clevis 3 8 x 1 2
4. of the sweeper Do not tighten yet See figure 1 STEP 3 REMOVE PLASTIC TIE 5 Remove the plastic tie that fastens the height adjustment tube to the front of the sweeper housing See figure 1 5 16 x 1 3 4 HEX BOLT HOUSING MARKED L FIGURE 1 STEP 4 CONNECT HITCH TUBES 6 Fasten the hitch tubes together using two 5 16 x 3 hex bolts and 5 16 nylock nuts Do not tighten yet See figure 2 5 16 x 3 HEX BOLT ONY FIGURE 2 STEP 5 ASSEMBLE HITCH PIN 7 Assemble the hitch pin bracket the hitch spring and then the 7 16 flat washer onto the hitch pin Secure them to the hitch pin with a 1 8 x 3 4 cotter pin placed into the middle hole in the hitch pin Spread ends of cotter pin around hitch pin See figure 3 8 Assemble the hitch pin bracket to the straight hitch bracket using a 3 8 x 1 carriage bolt and a 3 8 nylock nut Align the brackets and tighten See figure 3 3 8 x 1 CARRIAGE BOLT gt ee 1 8 x 3 4 COTTER PINS Len HITCH PIN BRACKET HITCH BRACKET STRAIGHT 7 16 FLAT WASHER b 3 8 NYLOCK NUT l HITCH SPRING MIDDLE HOLE HITCH PIN FIGURE 3 STEP 6 MEASURE TRACTOR HITCH 9 If your tractor hitch measures 10 or more above the ground go to STEP 7a If your tractor hitch measures less than 10 above the ground go to STEP 7b STEP 7a ASSEMBLE HITCH BRACKETS For tractor hitches 10 or more above the ground 10 Place the bent hit
5. 7 HEIGHT ADJUSTMENT SLOT OIL BEARINGS HERE_ SARS MA FLAT WASHER J HEX BOLT FIGURE 27 4 Lubricate the wheel bearings each season Remove the hub cap and apply a few drops of light weight oil 5 Every two years remove the wheels and clean the gears found inside the wheel housing After cleaning lubricate the gears with an even coat of light grease To remove the wheel pop off the hub cap and remove the lock nut flat washer and hub cap washer See figure 28 HEX BOLT FLAT WASHER FLAT WASHER HUB CAP HUB CAP WASHER NYLOCK NUT FIGURE 28 CLEANING 6 Clean sweeper housing with a soft brush or cloth 7 Clean debris from hopper bag with a brush or broom 8 Remove any material which has wrapped around brushes or ends of brush shaft STORAGE CAUTION Before storing the sweeper always empty the hopper bag to avoid spontaneous combustion 1 Clean the sweeper and hopper bag thoroughly to help prevent rust and mildew 2 Tocollapse the hopper bag for storage remove the two hopper support rods from the rear of the hopper 3 Store in a dry area SERVICE AND ADJUSTMENTS BRUSH REPLACEMENT NOTE Brush replacement should be done one brush at a time Remove the hopper bag from the sweeper Loosen only the two hex bolts and lock nuts which clamp one brush in a brush retainer Do not loosen or remove the bolts which fasten the brush retainers to the brush shaft See fig
6. O t 2007 08 4 Husqvarna 42 Inch Lawn Sweeper 45 0352 Operator s Manual Exercise caution at all times when using power equipment 1 POM SAFETY RULES Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment Read the vehicle and sweeper owners manuals and know how to operate your vehicle and sweeper before using this sweeper attachment Always instruct other users before they operate the sweeper Do not permit children to operate sweeper Do not permit anyone to ride on sweeper Never attach the hopper rope to any part of your body or clothing Never hold onto the rope while towing the sweeper Attach the rope to the towing vehicle to keep it away from wheels and rotating parts Operate the sweeper at reduced speed on rough terrain near ditches and on hillsides to prevent loss of control 6 9 10 Vehicle braking and stability may be affected with the attachment of this sweeper Do not fill sweeper to maximum capacity without checking the capability of the towing vehicle to safely pull and stop with the sweeper attached Stay off of steep slopes Stop and inspect vehicle and sweeper for damage after striking an object Repair any damage before continuing operation Keep sweeper away from fire Excessive heat can damage the brushes and hopper bag and could cause the bag and its contents to burn Before storing the sweeper always e
7. bracket Tighten the height adjustment handle in place See figure 11 5 16 WASHER 5 16 NYLOCK NUT 5 16 x 1 HEX BOLT FIGURE 11 ASSEMBLY OF HOPPER BAG STEP 15 ASSEMBLE UPPER TUBES 1 Insertthe lefthand upper hopper tube through the stitched flaps of the hopper bag starting at the center cut out in the top of the bag See figures 12 13 and 14 Repeat for the right hand upper hopper tube UPPER HOPPER TUBE LEFT HAND SHOWN BAG FLAP CENTER CUT OUT START HERE FIGURE 12 2 Slide the two upper hopper tubes together and line up the center holes as shown in figure 13 UPPER HOPPER TUBES FIGURE 13 3 Fasten the upper hopper tubes together using a plastic plug See figure 14 PLASTIC PLUG FIGURE 14 STEP 16 ASSEMBLE LOWER TUBES 4 Assemble the two lower hopper tube together using a plastic plug See figure 15 PLASTIC PLUG FIGURE 15 5 Place the assembled lower hopper tubes into the bottom of the hopper bag and then slide the tubes to the back of the bag See figure 16 6 Attach the ends of the lower hopper tubes to the inside of the upper hopper tubes using two 3 8 x 1 2 clevis pins inserted from the inside and two small hair cotter pins See figure 16 SMALL HAIR COTTER PIN 3 8 x 1 2 CLEVIS PIN HOPPER BAG BOTTOM FIGURE 16 STEP 17 ATTACH BAG BOTTOM 7 Assemble the bag retainer and the bag frame strap to the front edge of the bag bottom P
8. ch bracket on top of the hitch tubes and place the straight hitch bracket with hitch pin underneath the hitch tubes Fasten together using a 5 16 x 2 1 2 hex bolt front a 5 16 x 2 1 4 hex bolt rear and two 5 16 nylock nuts as shown in figure 4 The bolts should straddle the front hitch tube bolt Do not tighten yet 1 Assemble the two hitch spacers onto the hitch pin and secure the pin with the large hairpin cotter See figure 4 5 16 x 2 1 4 5 16 x 2 1 2 HEX BOLT LARGE HEX BOLT HAIRPIN COTTER HITCH HITCH BRACKET STRAIGHT BRACKET 5 16 NYLOCK NUTS FIGURE 4 STEP 7b ASSEMBLE HITCH BRACKETS For tractor hitches less than 10 above the ground 12 Place the bent hitch bracket underneath the hitch tubes and place the straight hitch bracket with hitch pin on top of the hitch tubes Fasten together using a 5 16 x 2 1 2 hex bolt front a 5 16 x 2 1 4 hex bolt rear and two 5 16 hex lock nuts as shown in figure 5 The bolts should straddle the front hitch tube bolt Do not tighten yet 13 Assemble the two hitch spacers onto the hitch pin and secure the pin with the large hairpin cotter See figure 5 5 16 x 2 1 Z 5 16 X 2 1 4 HEX BOLT i HEX BOLT HITCH PIN HITCH __ SPACERS i HITCH n BRACKET ah 5 16 NYLOCK NUTS LARGE HAIRPIN COTTER FIGURE 5 STEP 8 TIGHTEN BOLTS 14 At this time tighten the four bolts in figure 1 that
9. emble a mounting clamp two bag arm tubes and another mounting clamp onto the rod as shown in figure 22 Push the rod on through the upper hopper tube on the opposite side of the bag MOUNTING CLAMP BAG ARM TUBE FIGURE 22 13 Assemble the two remaining hopper mount clamps onto the pivot rod on the outside of the bag Fasten them to the inside clamps using four 5 16 x 3 4 hex bolts and 5 16 nylock nuts Tighten securely See figure 23 14 Assemble two palnuts onto the ends of the pivot rod by lightly tapping them with a hammer See figure 23 15 Place a vinyl cap onto each bag arm tube See figure 23 HINT To ease assembly of the palnuts place the bag on its side on a hard surface With the bottom end of the pivot rod against the surface tap a palnut onto the top end of the rod Repeat for other end of rod VINYL CAP 5 16 NYLOCK NUT 5 16 x 3 4 MOUNTING CLAMP FIGURE 23 STEP 21 ATTACH ROPE 16 Secure the rope to the center of the upper rear hopper tube as shown in figure 24 FIGURE 24 STEP 22 ATTACH HOPPER BAG 17 To attach the hopper bag to the sweeper slide the ends of the bag arm tubes into the ends of the hitch tubes and secure with two 1 4 x 1 3 4 clevis pins and small hairpin cotters See figure 25 HAIRPIN COTTER FIGURE 25 STEP 22 ATTACH SWEEPER TO TRACTOR BRUSH HEIGHT ADJUSTED APPROXIMATELY MID WAY on Wy 1 Place the tractor and sweeper on a flat le
10. fasten the hitch tubes to the sweeper housing Next tighten the two bolts in figure 2 that fasten the ends of the hitch tubes together Finally tighten the two bolts in figure 4 or 5 that fasten the hitch brackets to the hitch tubes STEP 9 ASSEMBLE THE ANGLE BRACKET 15 Assemble the angle bracket to the sweeper housing using two 5 16 x 3 4 hex bolts and 5 16 nylock nuts The upright portion of the angle bracket should face toward the left side of the sweeper See figure 6 5 16 NYLOCK NUT ANGLE BRACKET 5 16 x 3 4 HEX BOLT FIGURE 6 STEP 10 ASSEMBLE HEIGHT ADJUST HANDLE 16 Assemble the plastic grip onto the upper height adjust handle See figure 7 17 Fasten the upper and lower height adjust handles together as shown in figure 7 Use one 5 16 x 1 hex bolt one 5 16 x 1 1 4 hex bolt two 5 16 washers and two 5 16 nylock nuts Place the washers against the slots in the upper handle Tighten the nuts and then loosen 1 2 turn so that the handles slide easily See figure 7 5 16 x 1 1 4 HEX BOLT PLASTIC GRIP 5 16 WASHER 5 16 NYLOCK NUT 5 16 x 1 HEX BOLT 5 16 WASHER FIGURE 7 STEP 11 ASSEMBLE EXTENSION SPRING 18 Assemble a 5 16 x 1 hex bolt and a 5 16 nylock nut into the top hole in the height adjustment handles See figure 8 19 Assemble the extension spring onto the end of the upper bolt and the middle bolt in the height adjust handles Assemble a 5 16 nylock nut
11. lace the bag retainer on top and the bag frame strap underneath the bag bottom Fasten together using six 10 x 5 8 screws and 10 32 nylock nuts See figure 17 FRONT EDGE OF BAG BOTTOM 7 XN FRAME STRAP A 10 32 x 5 8 SCREW BAG RETAINER NYLOCK NUT FIGURE 17 8 Assemble the bag frame strap to the holes in the lower hopper tubes using two 1 4 x 1 1 8 clevis pins and small hair cotter pins See figure 18 FIGURE 18 STEP 18 ATTACH BAG SIDES 9 Fold the bag flaps around the lower hopper tubes and attach to the bag bottom using the snaps See figure 19 FIGURE 19 STEP 19 ASSEMBLE SUPPORT RODS IMPORTANT Do not over bend the support rods during the following step Over bending will decrease the supporting tension of the rods 10 Assemble the two hopper support rods as shown in figure 20 Place the ends of the rods into the holes in the upper and lower hopper tubes flexing the rod just enough to fit into the holes in the tubes SUPPORT RODS FIGURE 20 STEP 20 ASSEMBLE HOPPER ROD TUBES AND CLAMPS 11 If the hole in the side of the upper hopper tubes is covered over by the bag locate the hole by touch It is approximately midway along the side of the bag Pierce holes through the stitched bag flaps where the holes in both hopper tubes are located See figure 21 Sr UPPER HOPPER TUBE FIGURE 21 12 Slide the hopper bag pivot rod through the hole in an upper hopper tube Ass
12. mpty the hopper bag to avoid spontaneous combustion Follow maintenance and lubrication instructions as outlined in the maintenance section of this manual Look for this symbol to point out important safety precautions It means Attention Become alert Your safety is involved CARTON CONTENTS 0 1 Sweeper Housing Assembly 2 Bag Arm Tube 2 3 Hitch Tube R H Right Hand 4 Hitch Bracket Bent 5 6 7 8 9 1 Hitch Bracket Straight Hitch Pin Bracket Height Adjustment Strap Lower Height Adjust Handle Upper Height Adjust Handle Hitch Tube L H Left Hand 11 12 13 14 15 16 17 Rope Hopper Bag Wind Screen Upper Hopper Tube L H Upper Hopper Tube R H Lower Hopper Tube L H Lower Hopper Tube R H Hopper Bag Pivot Rod Hopper Support Rod 2 Bag Retainer Strap Bag Frame Strap SHOWN FULL SIZE REF wD gt DOVOZErF AC TOMDMVIOO 1 1 4 1 4 6 2 1 6 1 21 2 6 2 1 4 2 NOT SHOWN FULL SIZE DESCRIPTION Hex Bolt 5 16 18 x 3 Lg Hex Bolt 5 16 18 x 2 1 2 Lg Hex Bolt 5 16 18 x 2 1 4 Lg Hex Bolt 5 16 18 x 1 3 4 Lg Hex Bolt 5 16 x 1 1 4 Hex Bolt 5 16 x 1 Hex Bolt 5 16 x 3 4 Curved Head Bolt 5 16 x 1 5 8 Carriage Bolt 3 8 x 1 Screw 10 32 x 5 8 Nylock Nut 3 8 Nylock Nut 5 16 Hex Nut 5 16 Nylock
13. nd the gear teeth on the wheel and then reassemble the wheel The brushes should rotate only during forward rotation of the wheel If the brushes are driven rotated by both forward and reverse rotation of the wheel the drive pin is jamming in the ratchet gear Disassemble to clean and lubricate the drive pin and the ratchet gear See figure 30 7 Remove the second wheel and repeat the procedure RATCHET GEAR FIGURE 30 Adjust height till brushes are 1 2 down into grass Stop sweeper Remove obstruction Remove one wheel ata time to check for obstruction or damage Refer to Service and Adjustments section REPAIR PARTS FOR MODEL 45 0352 45 0352 669 42 PROFESSIONAL LAWNSWEEPER REPAIR PARTS FOR MODEL 45 0352 45 0352 669 42 PROFESSIONAL LAWNSWEEPER PART DESCRIPTION REF PART DESCRIPTION NO NO NO OONDOARWN O ONMNND 0 4 2 2 2 4 6 2 2 2 2 3 1 1 4 4 2 1 1 1 1 1 1 A 1 Hitch Tube R H Hitch Tube L H Housing Assembly Rivet Skirt 42 Retainer Skirt Height Adjustment Tube Ass y Retainer Dust Cover Ball Bearing Brush Bushing Ass y Rivet Brush Shaft Brush 42 Bolt Hex 1 4 20 x 1 Lg Nut Nylock 1 4 20 Thread Brush Retainer Washer Flat 78 x 1 25 x 06 Dowel Pin Drive Bolt Hex 5 16 18 x 3 4 Lg Nut Nylock 5 16 18 Thread Spacer 41 x 1 125 x 50 Washer Flat 1 1 2 x 375 x 062 Washer 849 x 598 x 025 Washer
14. ng vehicle Adjusts for various height tractor hitches HOW TO USE YOUR SWEEPER BRUSH HEIGHT ADJUSTMENT 1 To adjust your sweeper brushes to the best operating height lift up on the height adjustment handle to disengage it from the height adjustment strap Move the handle forward or backward to raise or lower the brush See figure 26 Best adjustment is when the brush setting is 1 2 down into the grass Always mow the grass to an even height before sweeping SWEEPING SPEED 2 Tryastarting speed of approximately 3 m p h third gear on most tractors Depending on the conditions it may be necessary to adjust the sweeping speed in order to achieve best results 11 DUMPING OF SWEEPER 3 Your sweeper can be dumped easily without getting off of the tractor Pull the rope forward to dump the hopper Always empty hopper after each use A CAUTION Never attach the hopper rope to any part of your body or clothing Never hold onto the rope while towing the sweeper Attach the rope to the towing vehicle to keep it away from wheels and rotating parts CAUTION Keep sweeper away from fire Excessive heat can damage the brushes and hopper bag and could cause the bag and its contents to burn MAINTENANCE SCHEDULED MAINTENANCE 1 Clean the sweeper after each use 2 Inspect for worn or damaged parts such as brushes and wheels 3 Lubricate the brush shaft bearing twice a year with a few drops of light weight oil See figure 2
15. onto each bolt so that one thread of the bolt extends through the nut See figure 8 5 16 x 1 HEX BOLT 5 16 NYLOCK NUT EXTENSION SPRING i ES 5 16 NYLOCK NUT ii FIGURE 8 STEP 12 ATTACH HEIGHT ADJUST HANDLE 20 Assemble the height adjust handles to the height adjustment tube on the front of the sweeper housing Use two curved head bolts bowed washers 5 16 lock washers and 5 16 hex nuts Do not tighten yet See figure 9 5 16 HEX NUT 5 16 LOCK WASHER BOWED WASHER CURVED HEAD BOLT HEIGHT ADJUSTMENT TUBE FIGURE 9 STEP 13 ATTACH HEIGHT ADJUST STRAP TO ANGLE BRACKET Place the height adjust strap between the angle bracket and the height adjustment handle Attach the height adjust strap to the angle bracket using a 5 16 x 1 hex bolt the small spacer a 5 16 washer and a 5 16 nylock nut Tighten See figure 10 2 5 16 x 1 HEX BOLT A SPACER SMALL HEIGHT ADJUST R 5 16 WASHER Sy ae NYLOCK NUT FIGURE 10 STEP 14 ATTACH HEIGHT ADJUST STRAP TO HEIGHT ADJUST HANDLE 22 Attach the height adjust strap to the height adjust handle using a 5 16 x 1 hex bolt 5 16 washer and 5 16 nylock nut Place the washer against the slot in the height adjust strap Tighten the nut and then loosen 1 2 turn so that the strap can slide freely See figure 11 23 Slide the height adjust handle so that it aligns with the height adjust strap and the angle
16. ure 29 3 Lift the brush out of the retainers noting on which side of the brush the bristles overlap See figure 29 4 Install new brush making sure the bristles overlap on the same side of the brush as before See figure 29 5 Tighten the two hex bolts and lock nuts to clamp the new brush in place before removing the next brush Ph OVERLAP BRISTLES i BRUSH RETAINER OVERLAP a A Donor X K REMOVE D OVERLAP BRISTLES FIGURE 29 TROUBLESHOOTING Wheels skid when sweeping 2 Brushes are jammed 3 Wheels are jammed 1 Brushes set too low WHEEL GEAR AND PAWL SERVICE IMPORTANT Do not remove both wheels at the same time to avoid mixing of parts The R H and L H ratchet gears are not interchangeable Make notes on the position of washers and snap rings during disassembly 1 Remove only one wheel from the sweeper 2 Remove the retaining rings and washers which hold the ratchet gear onto the brush shaft 3 Remove the gear by sliding it off the brush shaft Look for the drive pin which may fall out of the brush shaft when the ratchet gear is removed See figure 30 4 Toreassemble insert the drive pin through the hole near the end of the brush shaft Make sure the pin slides back and forth easily in the shaft See figure 30 5 Lightly grease the shaft and fill the ratchet gear with grease Assemble the ratchet gear back onto the shaft See figure 30 6 Lightly grease the axle a
17. vel surface 2 Set the sweeper height adjustment handle to about the middle of its adjustment range 3 Attach the sweeper hitch to the tractor hitch arranging the hitch spacers in one of six possible combinations as shown in GROUP A and GROUP B diagrams below IMPORTANT To obtain the best performance from your sweeper arrange the spacers so that the sweeper bag is approximately level with the ground and approximately 5 to 7 off the ground as shown in figure 26 APPROXIMATELY LEVEL 5 to 7 FROM SURFACE FIGURE 26 GROUP A For vehicles with hitches GROUP B For vehicles with hitches having 8 to 10 ground clearance having 10 to 13 ground clearance N HITCH BRACKET MOUNTED ABOVE HITCH TUBES HITCH BRACKET MOUNTED BELOW HITCH TUBES BLACK LINE IS TRACTOR HITCH OPERATION KNOW YOUR SWEEPER WINDSCREEN PIVOT ROD BAG ARM HOPPER BAG HOPPER ROPE HEIGHT ADJUSTMENT Hopper Bag Collects grass clippings leaves and debris Hopper Rope Permits dumping of hopper bag from driver s seat Windscreen Helps prevent collected material from being blown out of hopper bag Bag Arm Tubes Connects the hopper bag to the sweeper housing Pivot Rod Allows hopper bag to tilt forward to dump material Height Adjustment Handle Adjusts the operating height of the sweeper Height Adjustment Strap Holds the height adjustment handle in position when locked Hitch Bracket Connects the sweeper to the towi
Download Pdf Manuals
Related Search