Hunter 43042-01 User's Manual
Contents
1. Remove the pre loaded screw tip covers Back out the pre loaded screw tips until flush with the side of the housing 43042 01 02 21 2008 Pop out the first wiring access slug Use second if needed Insert the strain relief into the housing and secure with the washer Choose Installation Option For New Construction attaching to joist fo to step A11 page 6 For New Construction suspended between joists go to step B11 page 8 For Existing Construction accessible from above go to step C11 page 11 For Existing Construction accessible only from below go to step D11 page 15 43042 01 02 21 2008 HSI ISNA New Construction attaching to joist Position the correct depth mark at the bottom edge of the joist Screw pre loaded screws into joist or framing based on the thickness of your sheetrock ENGLISH Pull wires through the strain relief Ground S Green Bare Copper Black Main Switch 1 AC In Black Switch 2 AC In Connect wires as shown 43042 01 02 21 2008 5 8 Zir Install the wiring cover plate Make sure all Connect 4 duct and vent to the outside Tape joints wiring connections are inside the box or under If ducting does not fit securely an adapter may need the wiring cover plate to be purchased iz se m Z m ais Reinstall the motor by inserting the tabs and pushi2. 82048 Turino Bath Ventilator with Light EAD and SAVE THESE INSTRUCTIONS 43042 01 02 21 2008 TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING 1 Use this unit only in a manner intended by the manufacturer If Engineers ASHRAE and the local code authorities you have questions contact the manufacturer When cutting or drilling into wall s or ceiling do not Before servicing or cleaning the unit switch power off at ser damage electrical wiring or other hidden utilities vice panel and lock the service disconnecting means to prevent power from being switched on accidentally when the service Ducted fans must always be vented to the outdoors disconnecting means cannot be locked securely fasten a promi nent warning device such as a tag to the service panel _ If this unit is to be installed over a tub or shower it must be marked as appropriate for the application and be connected to a GFCI Ground Installation work and electrical wiring must be done by qualified Fault Circuit Interrupter protected branch circuit person s in accordance with all applicable codes and standards including fire rated construction Never place a switch where it can be reached from a tub or shower Sufficient air is needed for proper combustion and exhausting Install fan at least 5 feet 1 52 m above the floor of gasses through the flue chimney of fuel burning equipment to prevent backdrafti
3. ABOVE FOR SUCH MOTORS OR OTHER PARTS This warranty is voided if your Hunter bath exhaust fan is not purchased and installed in the U S A This warranty excludes and does not cover defects malfunctions or failures of any Hunter bath exhaust fan which were caused by repairs by persons not authorized by us use of parts or accessories not authorized by us mishandling improper installation modifications or damage to the Hunter bath exhaust fan while in your possession or unreasonable use including failure to provide reasonable and necessary maintenance To obtain servicing contact the nearest Hunter authorized service center of the Hunter Fan Company Service De partment 2500 Frisco Avenue Memphis Tennessee 38114 Please contact us before shipping your bath exhaust fan to us If we authorize you to ship it to us you will be responsible for all insurance and freight or other transpor tation charges to our factory or service center We will return your Hunter bath exhaust fan freight prepaid Your Hunter bath exhaust fan should be properly packed to avoid damage in transit since we will not be responsible for any such damage Proof of purchase is required when requesting warranty service The purchaser must present the sales receipt or other document that establishes proof of purchase INNO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAM AGES SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LAS
4. located next to the recepta cle Push up rear motor plate tab while pushing out on the side of the housing or insert a screwdriver into the slot in the housing next to tab and twist screw driver Gently vacuum fan motor and interior of housing METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN WATER The motor is permanently lubricated and never needs oiling If the motor bear Cooking ings are making excessive or unusual Equipment noises replace the motor with the exact service motor You should replace the impeller at the same time 43042 01 02 21 2008 Check all the parts If damaged call 1 888 830 1326 for replacements Extra Screws 95044 01 000 95029 01 000 75191 01 000 03242 07 133 98037 01 000 m Z 0 m ais 74508 03 133 gt gt gt D gt 77521 01 000 gt gt gt gt gt 65219 01 000 aon ee hese e S Jerr ULF 97959 01 000 P 15729 01 000 75184 01 133 97960 01 000 11535 01 000 Included Tools Needed Estimated assembly time 30 to 60 minutes 43042 01 02 21 2008 Before Installation NOTE Remove all packing materials before installation J TNA f C ENGLISH
5. air movement e Turn power on replace fuse or reset breaker e Check all plug connections to be sure they are secure e Check the wiring to make sure it matches the wiring diagram Problem Light does not come on Solution e Replace the light bulb with a new bulb e Turn power on replace fuse or reset breaker e Check all plug connections to be sure they are secure e Check the wiring to make sure it matches the wiring diagram Problem Fan is noisy Solution e Check and tighten all fasteners e Check the glass to make sure it is secure e Check the flapper to make sure it moves freely If you need parts or service assistance please call 888 830 1326 or visit us at our web site at http www hunterfan com 43042 01 02 21 2008 Hunter Fan Company Bath Exhaust Fan LIMITED WARRANTY Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter bath exhaust fan If any part of your Hunter bath exhaust fan except for glass fixtures and light bulbs fails at any time within one year afterthe date of sale to you due to a defect in material or workmanship we will repair or at our option replace the defective part free of charge for parts and labor performed at our nearest service center or at our Service Depart ment in Memphis Tennessee After this one year period you will be responsible for all parts and labor costs for repairs on the bath exhaust fan except for motor repa
6. the tabs and pushing up into position Make sure the wires are not pinched between the mo tor and the housing Turn on the power source Go to step on page 18 to attach grille Test the motor If the motor does not run check the plug con 43042 01 02 21 2008 N E D oa Xi N O Secure the motor by tightening the 2 screws nection HSI ISNA ENGLISH y LS l 4 X y A 4 Remove the strain relief bracket screw Position the strain relief bracket under the motor as shown Insert the strain relief bracket s dog leg tab so that it hooks Align posts A B C and D stamped into motor housing with over the lip of the motor Reinstall the strain relief bracket posts A B C and D stamped into light fixture Slide light screw 18 fixture over posts 43042 01 02 21 2008 Attach thumbscrews WARNING To reduce the risk of electrical shock all 4 thumbscrews MUST be properly installed HSI ISNA Screw glass stop into position Align glass dome and push up Screw Finial into position Complete 43042 01 02 21 2008 T 2 Z Lu Trouble Shooting Problem Fan does not come on Solution e Hunter Fan Bath Ventilators are extremely quiet To confirm that the fan is running place your hand near the vents to feel the
7. S 7 VN O W Secure the motor by tightening the 2 screws Turn on the power source 43042 01 02 21 2008 Go to step on page 18 to attach grille Test the motor If the motor does not run check the plug connection Existing Construction accessible from above NOR aE NCR TAN HSI ISNA Remove an existing fan and check to make sure the Use the motor housing as a template to mark position opening is large enough to accommodate the new motor housing 8x 8 5 Cut out an opening for the housing Slide the mounting rails into brackets 43042 01 02 21 2008 Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock 1E 2 Z Lu Insert screws leaving space between the screw head and the joist Screws are not provided Attach the rails onto the screws Tighten screws 43042 01 02 21 2008 Connect 4 duct and vent to the outside Tape joints Pull wires through the strain relief If ducting does not fit securely an adapter may need to be purchased m Z 0 m ais Tighten the strain relief screws Ground SS Green Bare Copper Fan Motor Black Main Switch 1 Black Switch 2 AC In Connect wires as shown 43042 01 02 21 2008 Install the wiring cover pla
8. TS OR THE EX CLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY TO YOU THE WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE 21 2008 Hunter Fan Company 43042 01 02 21 2008
9. irs as provided below If your Hunter bath exhaust fan motor fails at any time within five years after the date of sale to you due to a defect in material or workmanship labor and materials to repair the defect will be provided free of charge at our nearest service center or our Service Department in Memphis Tennessee If no replacement part can be provided we will at our option either refund the actual purchase price of your bath exhaust fan or provide a replacement free of charge After this five year period you will be responsible for all parts and labor costs for repairs on all parts of the bath exhaust fan IF THE ORIGINAL USER OR CONSUMER PURCHASER CEASES TO OWN THE FAN THIS WARRANTY AND ANY IMPLIED WARRANTY WHICH THEN REMAINS IN EFFECT INCLUDING BUT NOT LIMITED TO ANY IM PLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE VOIDED NO WARRANTY EXPRESS OR IMPLIED INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS MADE IN RESPECT OF GLASS FIXTURES OR LIGHT BULBS OR THE FINISH ON ANY METAL PORTION OF THE BATH EXHAUST FAN m Z m ais THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES THE DURATION OF ANY IMPLIED WARRANTY INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FIT NESS FOR A PARTICULAR PURPOSE IN RESPECT TO ANY HUNTER FAN BATH EXHAUST FAN MOTOR OR OTHER FAN PART IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH
10. ng Follow the heating equipment manufac This unit must be grounded turer s guideline and safety standards such as those published by the National Fire Prevention Association NFPA and the Unit must not be installed in a ceiling thermally insulated to a value American Society for Heating Refrigeration and Air Conditioning greater than R40 A CAUTION A WARNING For general ventilating use only Do not use to exhaust haz ardous or explosive materials and vapors D SCO N N ECT E LECTRI C To avoid motor bearing damage and noisy unbalanced impel lers keep drywall spray construction dust etc off power POWE R S U PPLY unit DO NOT install this product in a wall This product is AN D LOCK OUT designed for installation in ceilings up to a 12 12 pitch 45 degrees Ductwork must point upward S E RVI C E PAN E L B E FO RE Please read specification label on product for further infor mation and requirements S E RVI CI N G U N IT T 2 Z Lu PREVENTATIVE MAINTENANCE A clean fan provides better service Disconnect the power supply and clean the 07010 NG AREA fan as listed below CS Do Not Install Above TO CLEAN GRILLE Use a mild detergent such as dishwashing liquid and a soft cloth DO NOT use abrasive cloths steel wool pads or scouring powders Or Inside This Area TO CLEAN FAN ASSEMBLY Unplug motor cord from receptacle To remove motor plate find the single tab on the motor plate
11. ng up into position Make sure the wires are not pinched between the motor and the housing Secure the motor by tightening the 2 screws Turn on the power source 43042 01 02 21 2008 Go to step on page 18 to attach grille Test the motor If the motor does not run check the plug connection ENGLISH Slide the mounting rails into brackets Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock Mark position of screws by using holes as a template Drill a hole in the center of each outline 43042 01 02 21 2008 Insert screws leaving space between the screw Attach the rails onto the screws head and the joist Screws are not provided Tighten screws Pull wires through the strain relief Ground AN Green SD A Bare Copper Fan Motor X Black Switch 2 AC In Connect wires as shown 43042 01 02 21 2008 DEPE Install the wiring cover plate Make sure all wiring Connect 4 duct and vent to the outside Tape joints connections are inside the box or under the If ducting does not fit securely an adapter may need wiring cover plate to be purchased 1E 2 Z Lu Reinstall the motor by inserting the tabs and pushing up into position Make sure the wires are not pinched between the motor and the housing J oy IW zz
12. te Make sure all wiring Connect wiring from motor the motor connections are inside the box or under the to the wiring cover plate wiring cover plate ENGLISH Reinstall the motor by inserting the tabs and pushing up into Secure the motor by tightening the 2 screws position Make sure the wires are not pinched between the motor and the housing Turn on the power source Test the motor If the motor does not run check the plug connection 43042 01 02 21 2008 Go to step on page 18 to attach grille Existing Construction accessible only from below D EXISTING FAN DERNE Remove an existing fan and check to make sure the opening Move the housing into position above the ceiling is large enough to accommodate the new motor housing 8 x Pull wires through strain relief Attach existing ducting to duct connector Tape joints If ducting does not fit securely EG an adapter may need to be purchased 43042 01 02 21 2008 Install the housing flush with the sheetrock and secure by tight ening the pre loaded screws into the joist Ground AA Green Se Bare Copper T 2 Z Lu Fan Motor Black Switch 2 AC In Connect wires as shown Install the wiring cover plate Connect wiring from the motor to the wiring cover plate 43042 01 02 21 2008 Reinstall the motor by inserting
Download Pdf Manuals
Related Search