Huffy FR320UKT User's Manual
Contents
1. Secure free ends of tank struts to tank with carriage bolt 16 washer 21 and knob 17 as shown Repeat for other side KNOBS MUST BE TIGHTENED COMPLETELY AND CHECKED PERIODICALLY FOR TIGHTNESS 11 12 05 ID M611701 backboard ribbing Be sure to press completely into place Attach rim 18 to backboard 22 and pole bracket 20 with knob 17 reinforcement bracket 11 and carriage bolt 16 as shown Tighten knob completely Pole bracket 20 will need to be lightly pressed into D KNOB MUST BE TIGHTENED COMPLETELY AND CHECKED FOR TIGHTNESS BEFORE EACH USE PRESS BRACKET 20 INTO PLACE HERE Carefully tip unit forward and slide backboard assembly onto pole as shown Se LP SAWHORSE OR SUPPORT TABLE ID M611701 12 05 12 bolts 19 and knobs 17 as shown Install pole E cap 12 as shown Q Attach board assembly to pole with carriage Q Install net 8 E 13 12 05 ID M611701 Place assembled unit in desired location Fill Attach height and moving tank with water 26 gallons 98 4 liters or label 15 to front of pole as sand approx 360 Ib 163 kg and snap tank shown Regulation rim height cap 14 in place is 10 feet 3 05 m HEIGHT ADJUSTMENT and carriage bol B to extend or retract backboard and im Height adjustment rom 7 12 to 10 ADD TWO GALLONS 7 6 LITERS OF NON TOXIC ANTIFREEZE IN SUB FREEZING CLIMATES HEIGHT AND MO2. 2 MINIMUM OVERLAP LEAVING 1 1 2 the same Way FIG B BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER FIG A Wood Scrap NOT SUPPLIED ID M611701 12 05 8 wheel axle 2 with spacers 10 as shown 3 Install wheel axle 2 through wheel bracket 9 and install wheels 3 onto E THE SPACER 10 WILL FIT LOOSELY UNTIL SECURED INTO THE CAVITY OF THE BASE Attach wheel carriage assembly to base 1 with bolt 13 washer 21 and nut 7 as shown FINGER TIGHTEN NO TOOLS REQUIRED Assembly will be fully tightened in next step BE SURE THAT THE SQUARE PORTION OF THE CARRIAGE BOLT 13 IS PROPERLY SEATED IN THE SQUARE CUT OUT OF THE WHEEL BRACKET 9 12 05 ID M611701 and wheel bracket by turning the pole assembly clockwise as shown Tighten pole completely and further rotate pole until struts are aligned correctly as shown in FIG B Attach pole assembly to tank assembly as shown Secure pole assembly to tank 5 E TWO PEOPLE REQUIRED FOR THIS PROCEDURE FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE The pole should be turned approximately 7 complete rotations to tighten properly When properly tightened the wheel bracket will be tight against the base An assistant is recommended to hold the base in place during this step ID M611701 12 05 10 Rotate struts down and bend struts outward to line up with holes on base as shown
3. 900253 203309 PARTS LIST Description Tank Black Wheel Axle Wheel Top Pole Section Middle Pole Section with Label Bottom Pole Section Assembly Nut Hex Flange 3 8 16 Net Wheel Bracket Spacer Wheel Axle Rim Bracket Cap Bolt Carriage 3 8 16 x 1 5 Long Tank Cap Label Moving System and Height Adjust Bolt Carriage 5 16 18 x 1 75 Long Knob Plastic 3 sided Rim Bolt Carriage 5 16 18 x 4 Backboard Mounting Bracket Washer 406 I D x 1 0 O D Backboard YOU MAY HAVE EXTRA PARTS WITH THIS MODEL 5 12 05 ID M611701 PARTS IDENTIFIER Actual Size 13 1 LO 21 3 CE LC Y OF 7 1 i PARTS IDENTIFIER Not Actual Size 3 2 S 12 1 22 1 ID M611701 12 05 Correctly identify each pole section Poles have an identification sticker a that will be used as a reference point in the next step Reference Stickers TOP MIDDLE BOTTOM 7 12 05 ID M611701 IMPORTANT ONCE POLE SECTIONS ARE POUNDED TOGETHER THEY CANNOT BE TAKEN APART Align poles using alignment marks First pound top 2 E and middle poles together by bouncing them on a scrap piece of wood on the ground as shown in FIG A until TE DENTIA TON TEETE they no longer move toward pole identification stickers THE POLE WHEN PROPERLY e e POUNDED TOGETHER THE POLE THEN add bottom pole section and pound together in SECTIONS SHOULD HAVE A 3 1
4. Portable System Jas Owners Manua Customer Service Center SQ Wood Board N53 W24700 South Corporate Circle Sussex WI 53089 U S A a scrap e Sawhorse or Support Table e Garden Hose or Sand st H nil Write Model Number Zi READ AND UNDERSTAND From Box Here OPERATOR S MANUAL BEFORE USING THIS UNIT FAILURE TO FOLLOW we OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY Toll Free Customer Service Number for U S 1 800 558 5234 For Canada 1 800 284 8339 For Europe 00 800 555 85234 Sweden 009 555 85234 For Australia 1 800 632 7921 Internet Address http www huffysports com 12 05 ID M611701 COPYRIGHT 2005 by SPALDING 1 HEIGHT ADJUSTMENT Rest unit on support table Remove adjustment knobs A and carriage bolts B to extend or retract backboard and rim Height adjustment from 7 1 2 to 10 Read and understand warnings listed below before using this product Failure to follow these warnings may A result in serious injury and or propert A WARNING LER aE jury property Backboard may rotate during height adjustment k Owner must ensure that all players know and follow these rules for safe operation of the system DO NOT HANG on the rim or any part of the system including backboard support braces or net A WARNING During play especially when performing dunk type activities Do not adjust height of system keep player s face away from the backboard r
5. VING LABEL MUST NOT OBSTRUCT FACTORY ATTACHED WARNING LABEL TWO PEOPLE REQUIRED FOR THIS PROCEDURE FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE LLL DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY IT MAY TIP OVER SES TWh yy W VW WM K VE 10 feet 3 05 m IF USING SAND 2 GALLONS OF ANTI FREEZE IS NOT REQUIRED ID M611701 12 05 14
6. _support product_registration Call TOLL FREE Customer Service or mail in the enclosed postcard Number listed on the front page WARRANTY CARD 3 12 05 ID M611701 Get to know the basic parts of your basketball system FRONT VIEW BACK VIEW BACKBOARD RIM ELEVATOR ASSEMBLY TOP POLE MIDDLE POLE STRUTS BOTTOM POLE BASE N WHEEL CARRIAGE ASSEMBLY ID M611701 12 05 4 lt S 3 EE O OCEA GOE E EE E EECH EE ECKE SEISETEESEE EE EE ET EE 2 CQ N 0 D e sch sch sch St POD SS sch sch Ss iS St DD sch sch S Part No 206646 200628 226401 908200 908246 900644 203041 201342 201651 902319 206219 266001 203617 5E2356 203084 201344 203053
7. e storage position and or in an area protected from the wind and free from personal property and or overhead wires Never play on damaged equipment When moving system use caution to keep mechanism from shifting Keep pole top covered with cap at all times Do not allow water in tank to freeze During sub freezing weather add 2 gallons of non toxic antifreeze sand or empty tank completely and store Do not use salt While moving system do not allow anyone to stand or sit on base or have added ballasting on base Do not leave system unsupervised or play on system when wheels are engaged for moving Use Caution when moving system across uneven surfaces System may tip over Use extreme caution if placing system on sloped surface System may tip over more easily See instruction manual for proper installation and maintenance 3 Carefully rotate basketball system upright 5E2356 05 05 ALDING HYDRA RIs In the U S 1 800 772 5346 In the U S 1 800 334 9111 MUSSECL BATHLETIC HUFFY SPORTS In the U S 1 800 558 5234 In the U S 1 888 713 5488 Canada 1 800 234 8339 ID 556790 05 05 ID M611701 12 05 2 AA SAFETY INSTRUCTIONS A FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY Owner must ensure that all players know and follow these rules for safe operation of the system To ensure safety do not attempt to assemble this system without followin
8. g the instructions carefully Proper and complete assembly use and supervision are essential for proper operation and to reduce the risk of accident or injury A high probability of serious injury exists if this system is not installed maintained and operated properly If using a ladder during assembly use extreme caution Check base regularly for leakage Slow leaks could cause the system to tip over unexpectedly Seat the pole sections properly if applicable Failure to do so could allow the pole sections to separate during play and or during transport of the system Climate corrosion or misuse could result in system failure If technical assistance is required contact Customer Service Minimum operational height is 6 6 1 98m to the bottom of backboard Most injuries are caused by misuse and or not following instructions Use caution when using this unit NOTICE TO ASSEMBLERS ALL basketball systems including those used for DISPLAYS MUST be assembled and ballasted with sand or water according to instructions Failure to follow instructions could result in SERIOUS INJURY It is NOT acceptable to devise a makeshift weight system IMPORTANT Remove all contents from boxes Be sure to check inside pole sections hardware and additional parts are packed inside Questions or Missing Parts DONT JI hack 0 store dees remember to complete your product registration form either on www huffysports com customer
9. im and net in upright position System must Serious injury could occur if teeth face come in contact with be in down position to adjust backboard rim or net Do not slide climb shake or play on base and or pole MOVING SYSTEM or sand Never leave system in an upright position without filling base with weight as system may tip over causing 1 While holding pole rotate injuries basketball system forward When adjusting height or moving system keep hands and until wheels engage with fingers away from moving parts ground Do not allow children to move or adjust system Move basketball system to During play do not wear jewelry rings watches necklaces desired location etc Objects may entangle in net Surface beneath the base must be smooth and free of gravel or other sharp objects Punctures cause leakage and could cause system to tip over Check system for stability Keep organic material away from pole base Grass litter etc could cause corrosion and or deterioration Check pole system for signs of corrosion rust pitting chipping and repaint with exterior enamel paint If rust has penetrated through the steel anywhere replace pole immediately Check system before each use for proper ballast loose hardware excessive wear and signs of corrosion and repair before use Check system before each use for instability Do not use system during windy and or severe weather conditions system may tip over Place system in th
Download Pdf Manuals
Related Search