HP tx2-1305au Modem and Local Area Network User Guide
Contents
1. in your current modem location setting follow these steps 1 Select Start gt Devices and Printers Right click the device that represents your computer and click Modem settings Click the Dialing Rules tab 2 3 4 Select your modem location setting 5 Click Edit 6 Click either Tone or Pulse 7 Click OK twice e Check the telephone number you are dialing and the response of the remote modem Dial a telephone number make sure there is a response from the remote modem and then hang up e Set the modem to ignore dial tones If the modem receives a dial tone it does not recognize it does not dial and displays a No Dial Tone error message To set the modem to ignore all dial tones before dialing follow these steps Select Start Devices and Printers Right click the device that represents your computer and click Modem settings Click the Modems tab Click the listing for the modem Click Properties e dv m 5 09 Click Modem 6 Chapter 1 Using the modem select models only 7 Clear the check box for Wait for dial tone before dialing 8 Click OK twice Selecting a location setting 7 2 Connecting to a local area network Connecting to a local area network LAN requires an 8 pin RJ 45 network cable purchased separately If the network cable contains noise suppression circuitry 1 which prevents interference from TV and radio reception orient the circuitry end of the cable 2 tow2. Modem and Local Area Network User Guide Copyright 2009 Hewlett Packard Product notice Development Company L P This user guide describes features that are The information contained herein is subject common to most models Some features to change without notice The only may not be available on your computer warranties for HP products and services are set forth in the express warranty statements accompanying such products and services Nothing herein should be construed as constituting an additional warranty HP shall not be liable for technical or editorial errors or omissions contained herein First Edition October 2009 Document Part Number 539893 001 Table of contents 1 Using the modem select models only Connecting a modem cable cas spss dez inae asit ERE sine Ra EE ela Rage epa dead Connecting a country specific modem cable adapter ssssssss eene Selecting a lOCatION SUING rt E Viewing the current location selection 22424000000nnnnanHnnnnnnnnnnnnnnnnnnnnnnnnnnannnnnnnnnnnnnn Adding new locations when traveling oooonnoncccnnnnnaccccccnnnonccccnn nan ncc nc canon emen Solving travel connection problems ssssssssssssseeeeeeeee nennen nennen 2 Connecting to a local area network 1 Using the modem select models only The modem must be connected to an analog telephone line using a 6 pin RJ 11 modem cable included with select models only In
3. ard the computer pr To connect the network cable 1 Plug the network cable into the network jack 1 on the computer 2 Plug the other end of the cable into a network wall jack 2 A WARNING To reduce the risk of electric shock fire or damage to the equipment do not plug a modem or telephone cable into the RJ 45 network jack 8 Chapter 2 Connecting to a local area network Index C cable LAN 8 modem 2 country specific modem cable adapter 3 L local area network LAN cable required 8 connecting cable 8 M modem cable connecting 2 country specific cable adapter 3 noise suppression circuitry 1 modem software setting adding location 4 travel connection problems 6 N network cable connecting 8 noise suppression circuitry 8 noise suppression circuitry modem cable 1 network cable 8 T troubleshooting modem 6 Ww wireless network WLAN 8 Index 9
4. current location setting select your preference from the settings in the Location list and then click OK EY NOTE You can use the preceding procedure to add location settings for places within your own country as well as in other countries For example you could add a setting named Work that includes dialing rules for accessing an outside line Selecting a location setting 5 Solving travel connection problems If you experience modem connection problems when using the computer outside of the country in which you purchased it try the following suggestions e Check the telephone line type The modem requires an analog not a digital telephone line A line described as a PBX line is usually a digital line A telephone line described as a data line fax machine line modem line or standard telephone line is usually an analog line e Check for pulse or tone dialing An analog telephone line supports one of 2 dialing modes pulse dialing or tone dialing These dialing mode options are selected in the Phone and Modem settings The dialing mode option selected must match the dialing mode supported by the telephone line in your location To determine the dialing mode supported by a telephone line dial a few digits on the telephone and then listen for clicks pulses or tones Clicks indicate that the telephone line supports pulse dialing Tones indicate that the telephone line supports tone dialing To change the dialing mode
5. em cable into the modem jack 1 on the computer 2 Plug the modem cable into the country specific modem cable adapter 2 3 Plug the country specific modem cable adapter 3 into the telephone wall jack PA fs a L of Connecting a country specific modem cable adapter 3 Selecting a location setting Viewing the current location selection To view the current location setting for the modem follow these steps 1 Select Start gt Control Panel 2 Click Clock Language and Region 3 Click Region and Language 4 Click the Location tab to display your location 4 Chapter 1 Using the modem select models only Adding new locations when traveling By default the only location setting available to the modem is a location setting for the country in which you purchased the computer As you travel to different countries set the internal modem to a location setting that meets the operating standards of the country in which you are using the modem As you add new location settings they are saved by the computer so that you can switch among settings at any time You can add multiple location settings for any country A CAUTION To prevent losing your home country settings do not delete your current modem country settings To enable modem use in other countries while preserving your home country configuration add a new configuration for each location in which you will use the modem CAUTION To prevent co
6. nfiguring the modem in a way that violates the telecommunications regulations and laws of the country you are visiting select the country in which the computer is located The modem may not function properly if the correct country selection is not made To add a location setting for the modem follow these steps 1 Select Start Devices and Printers 2 Right click the device that represents your computer and click Modem settings EY NOTE You must set up an initial current location area code before you can view the Dialing Rules tab If you do not have a location set up you will be prompted to enter the location when you click Modem settings Click the Dialing Rules tab Click New The New Location window is displayed In the Location name box type a name such as home or work for the new location setting gt m mA d Select a country or region from the Country region drop down list If you select a country or region that is not supported by the modem the Country region selection for USA or UK is displayed by default 7 Enterthe area code a carrier code if necessary and the number to access an outside line if necessary 8 Next to Dial using click Tone or Pulse 9 Click OK to save your new location setting The Phone and Modem window is displayed 10 Do one of the following e To set your new location setting as the current location click OK e To select another location setting as the
7. some countries a country specific modem cable adapter included with select models only is also required Jacks for digital PBX systems may resemble analog telephone jacks but they are not compatible with the modem A WARNING Connecting the internal analog modem to a digital line can permanently damage the modem Immediately disconnect the modem cable if you accidentally connect it to a digital line If the modem cable contains noise suppression circuitry 1 which prevents interference from TV and radio reception orient the circuitry end 2 of the cable toward the computer Connecting a modem cable A WARNING Toreduce the risk of electric shock fire or damage to the equipment do not plug a modem cable included with select models only or telephone cable into the RJ 45 network jack To connect a modem cable 1 Plug the modem cable into the modem jack 1 on the computer 2 Plug the modem cable into the RJ 11 telephone wall jack 2 2 Chapter 1 Using the modem select models only Connecting a country specific modem cable adapter Telephone jacks vary by country To use the modem and the modem cable included with select models only outside the country in which you purchased the computer you must obtain a country specific modem cable adapter included with select models only To connect the modem to an analog telephone line that does not have an RJ 11 telephone jack follow these steps 1 Plug the mod
Download Pdf Manuals
Related Search