HP t200 Hardware Reference Manual
Contents
1. Bracket Figure C 2 Removing the mounting bracket Supported Mounting Options Figure C 3 t200 Zero Client mounted on back of monitor stand Appendix C Mounting the HP t200 Zero Client for MultiSeat ENWW ENWW Figure C 4 t200 Zero Client mounted on back of monitor Figure C 5 t200 Zero Client mounted on wall LMM Figure C 6 t200 Zero Client mounted under desk Supported Mounting Options 9 Non supported Mounting Option A CAUTION Mounting the t200 Zero Client in an non supported manner could result in failure of the mounting bracket and damage to the t200 Zero Client and or other equipment Do not mount the t200 Zero Client on a flat panel monitor stand between the panel and the stand Figure C 7 Unsupported mounting position t200 Zero Client between stand and monitor 10 Appendix C Mounting the HP t200 Zero Client for MultiSeat ENWW D HP t200 Zero Client for MultiSeat Operation Routine t200 Zero Client Care Use the following information to properly care for the t200 Zero Client e Never operate the t200 Zero Client with the outside panel removed e Keep the t200 Zero Client away from excessive moisture direct sunlight and extreme heat and cold For information about the recommended temperature and humidity ranges for the t200 Zero Client see Specifications on page 4 e Keep liquids away from the t200 Zero Client e Turn off the t200 Zero Client and w2. 1000ft to a maximum of 3Km Zero Client is attached to a flat panel using the 10 000f with no direct sustained sunlight Upper limit mounting bracket is 50 to 95 F 10 to 35 C may be limited by the type and number of options installed Relative Humidity non condensing Operating 10 90 10 90 max wet bulb temperature is 28 C or 84 2 F 5 95 5 95 Nonoperating max wet bulb temperature is 38 7 C or 101 6 F Maximum Altitude unpressurized Operating 3 048 m 10 000 ft max allowed rate of change is 457 m per minute or 1500 ft per minute Nonoperating 9 144 m ice max allowed rate of change is 457 m per minute or 1500 ft per minute Appendix A Specifications ENWW B Security Provisions HP t200 Zero Client for MultiSeat Security Clip The t200 Zero Client ships with a security clip which can be fastened to the rear panel of the t200 Zero Client To prevent unauthorized removal of the t200 Zero Client fasten a padlock through the clip and a cable Securing the HP t200 Zero Client for MultiSeat Figure B 1 Securing the t200 Zero Client 1 With the tab of the t200 Zero Client security clip pointing up insert the t200 Zero Client security clip between the guides on the back of the t200 Zero Client 1 Use the provided screw to fasten the security clip to the t200 Zero Client 2 2 Insert a padlock through the loops of the security clip 3 and a cable ENWW HP t200 Zero Client
3. for MultiSeat Security Clip 5 6 Securing the HP t200 Zero Client for MultiSeat in the Mounting Bracket Figure B 2 Securing the t200 Zero Client in the mounting bracket 1 With the tab of the t200 Zero Client security clip pointing down insert the t200 Zero Client security clip between the guides on the back of the t200 Zero Client into the slot on the back of the mounting bracket 1 Use the provided screw to fasten the security clip to the t200 Zero Client 2 2 Insert a padlock through the loops of the security clip 3 and lock it to prevent access to the security clip screw Appendix B Security Provisions ENWW C Mounting the HP t200 Zero Client for MultiSeat Before mounting the t200 Zero Client be sure to attach the mounting bracket Mounting Bracket The t200 Zero Client ships with a mounting bracket which should be used to secure the t200 Zero Client to various mounting solutions The bracket incorporates four mounting points on one side of the unit These mounting points follow the VESA Video Electronics Standards Association standard which provides industry standard mounting interfaces for Flat Displays FDs such as flat panel monitors flat displays and flat TVs Attaching the HP t200 Zero Client for MultiSeat to the Mounting Bracket Figure C 1 Inserting the t200 Zero Client into the mounting bracket ENWW Mounting Bracket 7 8 Releasing the HP t200 Zero Client for MultiSeat from the Mounting
4. Ap Hardware Reference Guide HP t200 Zero Client for MultiSeat Copyright 2011 Hewlett Packard Development Company L P The information contained herein is subject to change without notice Microsoft and Windows are trademarks of Microsoft Corporation in the U S and other countries The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services Nothing herein should be construed as constituting an additional warranty HP shall not be liable for technical or editorial errors or omissions contained herein This document contains proprietary information that is protected by copyright No part of this document may be photocopied reproduced or translated to another language without the prior written consent of Hewlett Packard Company First Edition August 2011 Document Part Number 667766 001 About This Book WARNING Text set off in this manner indicates that failure to follow directions could result in bodil y harm or loss of life A CAUTION Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information Ey NOTE Text set off in this manner provides important supplemental information ENWW iv About This Book ENWW Table of contents 1 Front Panel Components oiiicisississsiissciisscinsioiciniianinuiksikiaiseieimdaiaimneaie 1 2 Rear Panel Components isciccisissi
5. ipe the exterior with a soft damp cloth as needed Using cleaning products may discolor or damage the finish Supported Orientations HP supports the following orientations for the t200 Zero Client A CAUTION You must adhere to HP supported orientations to ensure your t200 Zero Client functions properly e Ifthe t200 Zero Client is not to be mounted only the horizontal orientation is supported Be sure to set the t200 Zero Client on its rubber feet Figure D 1 Horizontal orientation e You can lay the t200 Zero Client under a monitor stand with at least one inch of clearance ENWW Routine t200 Zero Client Care 11 Figure D 2 Under monitor stand aa 12 Appendix D HP t200 Zero Client for MultiSeat Operation ENWW Non supported Orientation HP does not support the following orientation for the t200 Zero Client Z CAUTION Non supported placement of the t200 Zero Client could result in operation failure and or damage to the devices CAUTION The t200 Zero Client requires proper ventilation to maintain operating temperature Do not block the vents Do not put the t200 Zero Client in a drawer or other sealed enclosure Do not place a monitor or other object on top of the t200 Zero Client The t200 Zero Client requires proper ventilation to maintain operating temperatures Figure D 3 Do not put the t200 Zero Client in a drawer or other sealed enclosure Figure D 4 Do not place a monitor on the t200 Zero Clie
6. n supported orientations location 2 inadrawer 13 under a monitor 13 Vv vertical orientation 11 P VGA connector location 2 power LED location 1 Ww R weight 4 rear panel components 2 relative humidity specifications 4 routine care 11 S security 5 security clip 5 attaching 5 attaching to mounting bracket 6 security clip slot 2 serial number location 3 service repair 14 shipping preparation 14 specifications altitude 4 dimensions 4 hardware 4 humidity 4 relative humidity 4 t200 Zero Client 4 temperature 4 weight 4 supported mounting options 8 supported orientations 11 horizontal 11 under monitor stand 11 vertical 11 T temperature specifications 4 U unsupported mounting option 10 USB connectors 1 Index 15
7. nt ENWW Non supported Orientation 13 14 E Shipping Information Shipping Preparation Follow these suggestions when preparing to ship the t200 Zero Client 1 Turn off external devices connected to the t200 Zero Client 2 Disconnect the system components and external devices from their power sources then from the t200 Zero Client 3 Pack the system components and external devices in their original packing boxes or similar packaging with sufficient packing material to protect them Ey NOTE For environmental nonoperating ranges see Specifications on page 4 Important Service Repair Information In all cases remove and safeguard all external options before returning the t200 Zero Client to HP for repair or exchange Appendix E Shipping Information ENWW Index A altitude specifications 4 B bracket mounting 7 c cautions mounting t200 Zero Client 10 t200 Zero Client orientation 11 13 ventilation 13 components front panel 1 rear panel 2 D DC adapter optional 1 DC power connector 2 dimensions 4 F front panel components 1 H hardware specifications 4 headphone connector location 1 horizontal orientation 11 humidity specifications 4 M microphone connector location 1 monitor 1 mounting bracket 7 attaching 7 removing 8 mounting options on back of monitor stand 8 on wall 8 under desk 8 with flat panel on wall 8 mounting t200 Zero Client 7 ENWW N USB PC power connector no
8. pply power to the t200 Zero Client ENWW 2 2 Rear Panel Components For more information http www hp com and search for your specific t200 Zero Client model to find the model specific QuickSpecs Figure 2 1 Rear panel components 1 On off switch 5 DC power connector 2 Reset button 6 Ethernet RJ 45 connector 3 VGA connector 7 Security clip slot 4 USB PC connector to host PC USB Type A B cable included Chapter 2 Rear Panel Components ENWW 3 Serial Number Location Figure 3 1 Serial number location Every t200 Zero Client includes a unique serial number located as shown in the following illustration Have this number available when contacting HP customer service for assistance ENWW A Specifications Table A 1 t200 Zero Client Dimensions Width side to side 136 mm 5 35 in Height without mounting bracket 35 mm 1 38 in Height with mounting bracket 41 mm 1 61 in Depth front to back 91 mm 3 58 in Approximate Weight Without mounting bracket 343 g 12 1 oz With mounting bracket 381g 13 44 oz Temperature Range Operating 10 to 40 C 50 to 104 F max rate of change is 10 C per hour or 18 F per hour Nonoperating 30 to 60 C 22 to 140 F max rate of change is 20 C per hour or 36 F per hour Specifications are at sea level with altitude derating of The operating temperature range when the t200 1 C 300m 1 8 F
9. sndsesceaiariinescotisinenniaaendnaiaaniaineen 2 3 Serial Mier LOGO ccs rsecssasnscccssnsssanecerniaseconsansenateccqnsasetstanmeiaaes ante teee EES EEEE 3 Appendix A Specifications saiscinasiiainaissasinicinasinaincsimninnmnindmuimamiisnaen 4 Appendix B Security Provisions sicscsisscscccsncssiscstisussscssiserssiossncsansovendssnscasseussasusismeasemeisesonnasens 5 HP t200 Zero Client for MultiSeat Security Clip ssssnnssssnsssseoessssotssseetrsrsosrsrersrssnrsrseerseseeresssene 5 Securing the HP t200 Zero Client for MultiSeat ccccccceesseceeeeseeeeeeeneeeeeeneeeessteeeeeeses 5 Securing the HP t200 Zero Client for MultiSeat in the Mounting Bracket 000000e 6 Appendix C Mounting the HP t200 Zero Client for MultiSeat ssscccscscccssscssceecssssseseee 7 Mg nting RGF srs tinuro ss ptaitesteieay ocnucnosa R A a E EER E E E a E E a EE atacand ens 7 Attaching the HP t200 Zero Client for MultiSeat to the Mounting Bracket eceeeereeee 7 Releasing the HP t200 Zero Client for MultiSeat from the Mounting Bracket eeee 8 Supported Mounting HONS ep cctuceineetbeeavecucesisevasaetbeivaissatiene nies ne rtaxies indeed neeraneneenda 8 Non supported Mounting Option svccsunissawrhnassnuiasaanstenendvadeavadosehinadadvedpneisnimhdsadpnindwumhtanlesiiadgmmlpael 10 Appendix D HP t200 Zero Client for MultiSeat Operation cccccccsscccscesceecsssceceeecees 11 Routine t200 Zero Client Care ass
10. tsncpiinortineniunsnasdionddeanheuatiuhates aso sankisamcumannupn shana ameseuetucsmeudds 11 Supported Cae THN GINS ri ncani va vehesonsape sens iire ran E a NE N A E ERNER 11 Non supported Ope rtentl itt suesceaasiatoaveteinns deincloebstanbiseae sede tseiieaelositieldnosbbatietvin dosistibeledetinvae Bae Aellebies 13 Appendix E Shipping Informatori scsiissccissccisaseissceissseiteccisncsinnessiacsiemesinsiencrseonancines 14 Shipping Preparation sarrsiieirain ne ee e E E e E E 14 Important Service Repair Information 4 c csecnvessnnsnoresinsersnsnseeadenedeununnsenauntatvnsstndesintatedennntenpneees 14 De a A E E ee ee eae 15 ENWW vi ENWW 1 Front Panel Components For more information http www hp com and search for your specific t200 Zero Client model to find the model specific QuickSpecs Figure 1 1 Front panel components O 8 1 Power LED 3 Line out headphone audio connector 2 Line in microphone connector 4 USB 2 0 connectors 4 NOTE Ifthe optional DC adapter is not connected the t200 Zero Client supports a standard USB keyboard and USB mouse plus one 100 mA USB device low power such as some flash drives If the optional DC adapter is connected to a working power outlet or to the monitor the t200 Zero Client supports a USB keyboard a USB mouse and two 500 mA high power USB devices HP monitors with power pass through such as the HP LE1851wt 18 inch Widescreen LCD Monitor can su
Download Pdf Manuals
Related Search