HP Printer 70 User's Manual
Contents
1. 2 Open the second back part of the flap and lift it back fully The print carriage will move to the left and then back to the right Wait for it to stop When the carriage has stopped moving unplug the power cable from the power supply 23 HP Designjet 70 1 10plus Printer series Quick Reference Guide How do clean a printhead continued 3 Pull the printhead cover up and towards you so that the hook at the front unlatches itself and then push the whole cover back so that the printheads are exposed 4 Remove the failed printhead by lifting the small handle on the top and using it to pull the printhead vertically up and out of the printer 5 Ensure that no tape is covering the printhead contacts If the tape is present remove it 6 Gently wipe the printhead contacts with a clean soft lint free cloth 24 HP Designjet 70 1 10plus Printer series Quick Reference Guide How do clean a printhead continued 7 Ifthe printhead contacts are still dirty Slightly moisten the cloth with distilled water and continue softly wiping the contacts until they are clean 8 Place the printhead on a paper towel and leave it to dry for at least five minutes 9 While the printhead is drying clean the contacts inside the carriage in the same way 25 HP Designjet 70 1 10plus Printer series Quick Reference Guide How do clean a printhead continued 10 When both the print2. More information For more information about your printer including Windows and Mac drivers and networking information and troubleshooting printer problems reter to the HP a Driver and Documentation CD For additional information about the Windows driver use the on line help for the driver The information contained herein is subject to change without notice The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services Nothing herein should be construed as constituting an additional warranty HP shall not be liable for technical or editorial errors or omissions contained herein HP Designjet 70 1 10plus Printer series Quick Reference Guide There are four ways of loading sheets of paper into the printer if you have the Automatic Roll Feed installed on your printer There are three ways of loading paper if you have the manual roll feed or no roll feed installed 3 rear path sheet manual roll extensions 4 to support output tray ve ical has p 2 front path gt j l 1 input tray 1 The input tray at the front of the printer for multiple sheets of paper between 76 x 142 mm 3 x 5 6 inches and 457 x 610 mm 18 x 24 inches C Envelopes can also be loaded in the input tray 2 The front path for single sheets of paper between e 152x229 mm 6 x 9 inches and 458 x 1625 mm 18 03 x 63 9 inches A2 oversize 70
3. 1 Set your application to pick paper from the roll feed 2 Select Print trom your application 3 Load a roll of the required paper onto the spindle Make sure that the roll is turned the right way with the surface on which you wish to print facing up and that the blue stop on the spindle is pushed in against the paper 4 Insert the spindle into its retaining slots with the blue stop on the right A and the black stop on the left B as seen from the rear of the printer If the paper is glossy we recommend that you wear gloves to avoid smearing the surtace of the paper 5 Make sure that the leading edge of the roll is straight and perpendicular to its side edges 15 HP Designjet 70 1 10plus Printer series Quick Reference Guide How do I load a roll of paper 70 continued 6 Rewind any excess paper so that the paper is rolled tightly onto the spindle ve 7 Insert the leading edge of the paper into the rear of the printer until it encounters resistance keeping the sides of the paper rolled tightly so that the paper is properly aligned 8 After emitting a beep the printer will take up the paper 9 The printer will check the alignment of the paper If the roll is properly aligned the roll icon will appear on the display indicating that the printer is ready to print If the roll is misaligned the printer will eject the paper and the display will show the misaligned and roll icons in t
4. 10plus Printer series Quick Reference Guide Ce ISO A4 UP ies Closed DOWN Closed N A ARCH A 9 12 A Size DIN CA 324mm ISO B4 353mm LEGAL 14 eo Closed DOWN Closed N A _ SO A3 420mm l baa i iti Input tray i gt ul les il DOWN Closed N A BSize ARCH B 18 DIN C3 ASE Le ue DOWN Closed N A ISO B3 500mm osition DOWN Closed Closed 17x29 JIS B3 264mm 515mm CSize ANSIC 22 ISO A2 594mm DOWN Closed Closed ue C 5 ER TD D 3 Output Position Front path ane C Size DIN C2 458mm 648mm DOWN Closed Roll DOWN Closed N A icon Position A Size P Closed DOWN Closed N A Rear path Output SO A5 148mm 210mm position sheet tray Cu C Size A5 Position DOWN Closed Roll icon Position DOWN Closed Roll icon DIN C2 648mm Rear path Output Cuan Up to roll tray 18 ns B n B HP Designjet 70 1 10plus Printer series Quick Reference Guide How do print on large sheets 1 10plus Printer series The printer output system has several adjustable components When printing on large sheets of paper it is important that you use the correct printer output configuration The tollowing diagram shows adjustable parts of the printer output system The table on the next page gives the output system configuration required for various paper sizes Note e When using the input tray or roll feed as the paper source make the necessary adjust
5. 10plus Printer series Quick Reference Guide Tell me about combinations of flashing icons Unload roll When flashing The printer is waiting for you to unload the roll manually Action Unload the roll completely you do not need to remove the spindle from the printer When off Normal Roll misaligned When flashing The roll of paper is misaligned and must be reloaded Action Unload the roll and reload it paying special attention to alignment When off Normal 45 HP Designjet 70 1 10plus Printer series Quick Reference Guide Tell me about HP Designjet System Maintenance The HP Designjet System Maintenance utility gives you access to support and troubleshooting facilities on the Web if you have an Internet connection Even without an Internet connection it provides several facilities that may help to solve printer problems To start HP Designjet System Maintenance under Windows 1 From the Windows taskbar select Start gt Settings gt Printers 2 Right click your printer s icon and select Printing Preferences Windows 2000 or XP or Properties Windows 98 or Me from the pop up menu 3 Select the Advanced tab and click the Maintenance button To start HP Designjet System Maintenance under Mac OS double click the HP Designjet System Maintenance icon on your desktop Alternatively under Mac OS X you can select your printer in the Print Center and click Configure Under Windows or Mac OS
6. Printers Product Options All Conforms to the following Product Specifications Safety IEC 60950 1 2001 EN 60950 1 2001 EMC CISPR 22 1997 EN 55022 1998 Class B EN 55024 1998 A1 EN 61000 3 2 2000 EN 61000 3 3 1995 A1 2001 FCC Title 47 CFR Part 15 Class B2 Additional Information The product herewith complies with the requirements of the Low Voltage Directive 73 23 EEC and the EMC Directive 89 336 EEC and carries the CE marking accordingly The product was tested in a typical configuration with HP Personal Computer Systems and peripherals This Device complies with Part 15 of the FCC Rules Operation is subject to the following two Conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that my cause undesired operation This product is assigned a Regulatory model number which stays with the regulatory aspects of the design The Regulatory Model Number is the main product identifier in the regulatory documentation and test reports this number should not be confused with the marketing name or the product numbers Except bundles including p n Q1292 60058 EyeOne Kit which are only intended for EMEA market Sant Cugat del Vall s Barcelona Agi January 25 2005 U Josep Maria Pujol Product Regulations Manager Local contact for regulatory topics only European Contact Hewlett Packard GmbH HQ TRE Herrenberger Strasse
7. printer will automatically perform some internal calibrations on the printhead and then on the alignment There must be paper in the tray during alignment you can use your least expensive paper Pre alignment calibrations may take some time especially if multiple printheads are replaced 29 HP Designjet 70 1 10plus Printer series Quick Reference Guide How do replace printheads continued 7 Check that the printhead icon on the front panel is no longer flashing The printhead has been replaced successfully For more detailed instructions for replacing a printhead see the topic How do replace printheads on the HP Designjet Driver and Documentation CD 30 HP Designjet 70 1 10plus Printer series Quick Reference Guide It the printheads are not correctly aligned poor quality printing will result To align printheads you need to use the HP Designjet System Maintenance utility This is normally installed when you install the software printer driver for your printer trom the HP Designjet Driver and Documentation CD For some functions the HP Designjet System Maintenance utility requires an Internet connection but you do not need this connection to pertorm printhead alignment See Tell me about HP Designjet System Maintenance on page 46 To align the printheads 1 Make sure that you have at least 5 sheets of A4 or Letter paper in the input tray 2 Start the HP Designjet System Maintenance 3 Sel
8. printer will check the alignment of the paper If the paper is properly aligned the Roll icon will appear on the display indicating that the printer is ready to print 19 HP Designjet 70 1 10plus Printer series Quick Reference Guide How do load a roll of paper 1 10plus Printer series continued If the paper is misaligned the printer will eject the paper and the display will show the Misaligned and Roll icons you will have to reload the paper Repeat Step 6 so that the paper is tightly rolled onto the spindle 20 HP Designjet 70 1 10plus Printer series Quick Reference Guide Important Do not pull on the roll of paper once it is taken up by the printer that is if there is any resistance There are two ways of unloading a roll of paper e If you want to unload the roll in order to feed a single sheet through the printer press the Cancel and OK keys on the front panel at the same time see below It you later request printing to the roll the Automatic Roll Feed will then automatically reload the roll e Ifyou want to unload the roll in order to completely remove it for example you no longer wish to use this roll of paper 1 Push the Eject button on the lett roll feed support at the rear of the printer Avoid pressing the Eject button several times as this can damage the paper 2 Pull the roll towards you and remove the paper completely trom the rear paper path of the printer The icons shown
9. your Web browser should be started automatically when you have followed the instructions above If you cannot follow these instructions successfully e it may be that your computer does not manage the printer In this case use HP Designjet System Maintenance trom the printer server e or it may be that the printer is managed by your computer but HP Designjet System Maintenance has not been installed In this case install it trom the HP Designjet Driver and Documentation CD 46 HP Designjet 70 1 10plus Printer series Quick Reference Guide Tell me more about my printer For much more about e how to use your printer e your printer s features including Mac driver and networking information e troubleshooting printer problems see the HP Designjet Driver and Documentation CD For information about the Windows driver use the on line help for the driver 47 HP Designjet 70 1 10plus Printer series Quick Reference Guide HP limited warranty statement HP Designjet 70 1 10plus Printer series HP product Duration of limited warranty Printer and related HP 1 year from the date of purchase by the customer hardware Software 90 days from the date of purchase by the customer Black printhead Until the end of warranty date printed on the product is reached or 530 cm of HP ink have been cycled through the printhead whichever occurs first Cyan magenta and yellow Until the end of warranty
10. 140 71034 Boeblingen Germany USA Contact Hewlett Packard Company HPCC 20555 S H 249 Houston Texas 77070 Australia Contact Hewlett Packard Australia Ltd Product regulations Manger 31 41 Joseph Street Blackburn Victoria 3130 Australia 59 invent Printed on recycled paper Imprim sur du papier recycl Stampato su carta riciclata Gedruckt aut Recyclingpapier Impreso en papel reciclado SODA Hewlett Packard Company 2005 04 2005 Q6655 9001 1 Printed in Germany Imprim en Allemagne Stampato in Germania Hewlett Packard Company Avenida Graells 501 08174 Sant Cugat del Vall s Barcelona Spain Q6655 90011
11. 2 The problem is that a roll of paper is jammed 33 The problem is paper not taken from the input tray 34 The problem is the printer rejects paper from front path or tray 34 The problem is the printer takes two or more sheets at ONCE oooccccccnncccnccnnnccnnnos 35 The problem is that the printer has stopped 36 The problem is that the printer has not received the job oooooocccnccnoniocccnncnnnnno 37 The problem is poor print quality 38 The problem is a flashing tool icon in the front panel 37 The problem is something else oooccccooccccnnooocccnnnnoccnnnnnnnonnnnnnncnnnnnnnncnnnnos 4 Tell me about Tell me about the front panel 42 Tell me about the icons on the front panel 44 Tell me about combinations of flashing icons 45 Tell me about HP Designjet System Maintenance occcccnconccccnnnncnnccnnnnnnnnnoccnnnnnos 46 Tell me more about my printer 47 Legal information HP limited warranty statement 48 Regulatory notices E TE II 52 HP Designjet 70 1 10plus Printer series Quick Reference Guide
12. HP Designjet 70 110plus series Quick reference guide O invent HP Designjet 70 110plus Printer series Quick Reference Guide How do load sheets of paper general quidance 3 How do load paper using the front path ocococonoccccnccnooccnnnnnnnononnnnnnonononnnos 5 How do unload paper from the front path ooc ooooocccncnnnnococcnononononnnnnnnanoninnoss 5 How do load paper into the input tray occcoooccccncnocnncnnccnnnnononnnonononnnnnonanononos 6 How do load sheet paper using the rear path2 9 How do print on large sheets 70 11 How do print on large sheets 1 10plus Printer series 13 How do load a roll of paper 70 15 How do unload a roll of paper 70 17 How do load a roll of paper 1 10plus Printer series 18 How do unload a roll of paper 1 10plus Printer series 21 How do replace ink cartridges2 22 How do clean a printhead oocccooocccnnoccnnnnnoccnnnnncnnnonononnnononnnnnnnnnnnnonnnnnos 23 How do replace printheads 27 How do align printheads cooooccccnccoocccnncnocccnnnnnocnnnononocnnnnnncnnnnnnononinnnnoos 31 The problem is a paper jam 3
13. OR CONDITIONS OF MERCHANTABILITY SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE Limitations of liability To the extent allowed by local law the remedies provided in this Warranty Statement are the customer s sole and exclusive remedies TO THE EXTENT ALLOWED BY LOCAL LAW EXCEPT FOR THE OBLIGATIONS SPECIFICALLY SET FORTH IN THIS WARRANTY STATEMENT IN NO EVENT SHALL HP OR ITS THIRD PARTY SUPPLIERS BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES WHETHER BASED ON CONTRACT TORT OR ANY OTHER LEGAL THEORY AND WHETHER ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Local law This Warranty Statement gives the customer specific legal rights The customer may also have other rights which vary from state to state in the United States from province to province in Canada and from country to country elsewhere in the world To the extent that this Warranty Statement is inconsistent with local law this Warranty Statement shall be deemed modified to be consistent with such local law Under such local law certain disclaimers and limitations of this Warranty Statement may not apply to the customer For example some states in the United States as well as some governments outside the United States including provinces in Canada may a Preclude the disclaimers and limitations in this Warranty Statement trom limiting the statutory rights of a consumer e g the United Kingdom b Otherwise
14. ace the printhead 1 Open the front hinged flap at the right of the printer 2 Open the second back part of the flap and lift it back tully The print carriage will move to the left and then back to the right Wait for it to stop 3 Pull the printhead cover up and towards you so that the hook at the front unlatches itself and then push the whole cover back so that the printheads are exposed 4 For each printhead that needs to be replaced 2 HP Designjet 70 1 10plus Printer series Quick Reference Guide How do replace printheads continued e Litt the small handle on the top and use it to pull the printhead vertically up and out of the printer e Take the new printhead and remove the tape that protects its electrical contacts and ink nozzles e Lower the new printhead into place and return the small handle to its lowered position 28 HP Designjet 70 1 10plus Printer series Quick Reference Guide How do replace printheads continued e Push the printhead gently into place so that it is secure Repeat this for each printhead that is to be replaced 5 When you have replaced the printheads as required pull the printhead cover towards you ensuring that the hook at its front edge latches onto the tab and then push it away from you to close the cover 6 Finally close the rear part and then the front part of the outer flap Note that after closing the flap the
15. ave no obligation to repair replace or refund until the customer returns the defective product to HP 8 Any replacement product may be either new or like new provided that it has tunctionality at least equal to that of the product being replaced 9 HP products may contain remanufactured parts or components equivalent to new in pertormance or may have been subject to incidental use 10 HP s limited warranty is valid in any country or locality where HP has a support presence for this product and where HP has marketed this product The level of warranty service you receive may vary according to local standards HP will not alter form fit or function of the product to make it operate in a country for which it was never intended to function for legal or regulatory reasons Contracts for additional services may be available for any authorized HP service tacility where the listed HP product is distributed by HP or an authorized importer 49 HP Designjet 70 1 10plus Printer series Quick Reference Guide 11 Any applicable print cartridge warranty shall not apply to HP print cartridges that have been refilled remanufactured refurbished misused or tampered with in any way Limitations of warranty TO THE EXTENT ALLOWED BY LOCAL LAW NEITHER HP NOR ITS THIRD PARTY SUPPLIERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND WHETHER EXPRESS OR IMPLIED WITH RESPECT TO THE HP PRODUCTS AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES
16. below flash until the paper is completely out because if the paper is only partially removed paper jams may subsequently occur Sometimes the paper may fall away from the rear path by itself DS BY You do not need to remove the spindle from its supports in the printer 2 HP Designjet 70 1 10plus Printer series Quick Reference Guide 1 Open the front hinged flap at the right of the printer 2 For each ink cartridge that needs to be replaced e Gripping it by its shorter top edges litt the ink cartridge vertically up and out of the printer e Lower the new ink cartridge into its slot until it clicks into place and is quite secure 3 Close the outer flap 22 HP Designjet 70 1 10plus Printer series Quick Reference Guide How do clean a printhead It a printhead fails or needs attention the corresponding icon on the front panel flashes Note that the illustration below shows the HP Designjet 70 Printer series Make sure the printhead is correctly seated If this is not the problem the most likely cause of failure is that the printhead contacts need to be cleaned You will need the following cleaning materials e Clean soft lint free material that will not come apart or leave fibres when damp a coffee filter for example e Distilled or filtered water e Paper towels Make sure the printer is powered on then do the following 1 Open the front hinged flap at the right of the printer
17. d If you leave the paper source set to Auto Select Windows or Automatic Mac OS the printer will start printing on any paper that is already loaded If you specify Rear Manual Feed you do not need to remove paper trom the tray before using the rear path 2 Submit your print job then wait for the Paper Status icon on the front panel to tlash before you load the sheet into the rear path See page 44 for more details about the icons on the front panel The Paper Status icon is shown on the right It the Automatic Roll Feed is installed on your printer and a roll of paper is in the rear path the roll will automatically be unloaded when you submit your print job The Paper Status icon will then tlash to indicate there is no longer any paper in the rear path You can then load your sheet It other icons appear such as the Roll icon with the Paper Jam icon or the Roll icon with the Paper Misalign icon you may have to unload the roll manually before continuing to load a sheet It the manual roll feed is installed on your printer and a roll of paper is in the rear path you will need to unload it manually before you can print on n sheet paper See How do unload a roll of paper 70 on page 17 3 When you are ready to load the sheet place the paper in the rear feed to the left as seen from the rear of the printer with the surface on which you wish to print facing up HP Designjet 70 1 10plus Printer series Quick Re
18. d by HP s limited warranty but in some countries may be covered under a separate support contract 4 For HP printer products the use of a refilled or non original HP consumable product ink printhead or ink cartridge does not affect either the warranty to the customer or any HP support contract with the customer However if printer failure or damage is attributable to the use of a non HP or refilled ink cartridge HP will charge its standard time and materials charges to service the printer for the particular failure or damage 5 If HP receives during the applicable warranty period notice of a defect in any software media or consumable product which is covered by HP s warranty HP shall deliver another product to customer to replace the defective one If HP receives during the applicable warranty period notice of a defect in any hardware product which is covered by HP s warranty HP shall either repair or replace the detective product at HP s option A replacement part in return for a detective one and remote part installation assistance if needed may be provided to the customer at HP s option HP may at its option waive the requirement for the customer to return the defective part 6 If HP is unable to repair or replace as applicable a detective product which is covered by HP s warranty HP shall within a reasonable time after being notified of the defect refund the purchase price for the product 7 HP shall h
19. date printed on the printheads product is reached or 200 cm of HP ink have been cycled through the printhead whichever occurs first Ink cartridge Until the genuine HP ink is depleted as indicated by the printer or the end of warranty date printed on the product is reached whichever occurs first A Extent of limited warranty 1 Hewlett Packard HP warrants to the end user customer that the HP products specified above will be free from defects in materials and workmanship for the duration specified above Customer is responsible for maintaining proof of date of purchase For software products HP s limited warranty applies only to a failure to execute programming instructions HP does not warrant that the operation of any product will be uninterrupted or error free HP s limited warranty covers only those defects which arise as a result of appropriate use of the product and does not apply to any a Improper or inadequate maintenance or modification b Software interfacing media parts or supplies not provided or supported by HP or c Operation outside the product s specifications Routine printer maintenance operations in the HP Designjet 70 1 1 Oplus 110plus nr such as cleaning and preventive maintenance services including 48 HP Designjet 70 1 10plus Printer series Quick Reference Guide parts contained in any preventive maintenance kit and HP service engineer visits are not covere
20. e tray extension out as far as it will go 4 Fan the paper by its short edge This helps to prevent adjacent sheets of paper trom sticking together HP Designjet 70 1 10plus Printer series Quick Reference Guide How do load paper into the input tray continued 5 Slide the paper into the tray under the tray cover ensuring that it touches the sides of the tray on the right and on the printer side 6 Push in the small tab on the right of the tray so that it fits snugly against the paper Move the larger tab on the left of the tray to the right so that it too fits snugly against the paper 7 Close the tray cover HP Designjet 70 1 10plus Printer series Quick Reference Guide How do load paper into the input tray continued 8 Lift up the output tray and insert the input tray into the printer keeping it straight and pushing it in from both sides as far as it will go The left inside corner must be aligned with the plastic paper tray guide and the right inside corner must be aligned with the sticker of the input tray 9 Lower the output tray pushing the tray slightly to the left Note that if the input tray is extended it will extend out beyond the output tray HP Designjet 70 1 10plus Printer series Quick Reference Guide In order to print on sheet paper using the rear path you must submit your print job to the printer betore loading the paper 1 Set the paper source to Rear Manual Fee
21. ect Maintain printheads then Align printheads 4 The printer will print a printhead alignment sheet Check that the sheet printed has a tick on it The tick should be cyan If this is not the case repeat the process 3 HP Designjet 70 1 10plus Printer series Quick Reference Guide The problem is a paper jam 1 Press the OK key the upper right key on the printer s front panel If this does not solve the problem 2 Turn off the printer 3 Remove all media from the tray Pull out any paper that is visibly stuck 4 Lift the top cover and pull out any paper that may be stuck Be caretul when you lift the cover not to damage or disturb any of the tubes or other internal parts of the printer 5 It there is a roll of paper at the rear of the printer remove it from its supports Remove the rear path carefully by pressing the buttons on each of its sides and pulling it straight out If you don t pull it straight out you may damage the paper sensor y o gt gt 4 ON Sn Removing the rear pi Tiss access to o the inside of the pen from the rear Pull out any paper that may be stuck inside or is accessible from the rear Replace the rear path and make sure it fits securely 7 Turn on the printer 8 We recommend that after clearing a paper jam you align the printheads to avoid problems of poor print quality To align printheads start HP Designjet System Maintenance see page 31 and select Align
22. et printer or product numbers such as Z X where Z and X are any single letter and is any number Electro Magnetic Compatibility EMC FCC statements U S A The U S Federal Communications Commission in 47 cfr15 105 has specified that the following notices be brought to the attention of users of this product Product identification numbers HP Printer with identification numbers BCLAA 0301 BCLAA 0302 BCLAA 0408 This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interterence received including interference that may cause undesired operation Shielded cables Use of shielded data cables is required to comply with the Class B limits of Part 15 of the FCC Rules Caution Pursuant to Part 15 21 of the FCC Rules any changes or moditications to this equipment not expressly approved by the Hewlett Packard Company may cause harmtul interference and void the FCC authorization to operate this equipment Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio 52 HP Designjet 70 1 10plus Printer series Quick Reference Guide Regula
23. ference Guide How do I load sheet paper using the rear path continued If your printer has two slots you must feed the sheet through the upper slot the lower slot is for roll paper only Sheet paper Roll paper 4 Align the left edge of the paper with the left mark on the rear feed If you do not see a mark align it with the paper stop near the left hand end of the roll feed spindle Make sure that the leading edge of the sheet is parallel to the slot and not skewed 5 Push the paper into the printer pushing it as far as it will go For best results you should push the paper in quickly rather than slowly 10 HP Designjet 70 1 10plus Printer series Quick Reference Guide How do print on large sheets 70 The printer output system has several adjustable components When printing on large sheets of paper it is important that you use the correct printer output configuration The following diagram shows adjustable parts of the printer output system The table on the next page gives the output system configuration required for various paper sizes Note e When using the input tray or roll feed as the paper source make the necessary adjustments to the output system to enable output to be stacked e If the output tray has prints stacked in it and you want to print from the roll feed empty the output tray and adjust it as necessary before printing continued on next page 11 HP Designjet 70 1
24. hat case you will have to reload the paper 16 HP Designjet 70 1 10plus Printer series Quick Reference Guide How do I unload a roll of paper 70 Important do not pull on the roll of paper once it is taken up by the printer that is if there is any resistance 1 Press the Cancel and OK keys at the same time to eject the roll of paper 2 Pull the roll towards you and remove the paper completely from the rear paper path of the printer The icons shown below flashes until the paper is completely out because if the paper is only partially removed paper jams may subsequently occur Sometimes the paper may by itself fall away from the rear path 3 You do not need to remove the spindle from the printer 17 HP Designjet 70 1 10plus Printer series Quick Reference Guide This section is only relevant if your printer has a roll feed installed Only one source of paper can be used by the printer at any one time so if a roll of paper is loaded and the software requests printing on a sheet of paper e If you have a manual roll feed installed on your printer you must unload the roll manually before you can print to a sheet of paper e If you have the Automatic Roll Feed installed on your printer the roll is automatically unloaded by the printer In any case the roll is automatically reloaded the next time printing to the roll is requested You can cut a roll without unloading it by pressing the OK ke
25. he Radio Interference Regulations of the Canadian Department of Communications Korean EMI statement AS a SJE AH 7 7 0 AAE RO AABAYSESS WE ANALY Buy EE ARAE Ol AS FA BA bep A AK He BAS mos FYE KoA MANGO ag 347 90H 53 HP Designjet 70 1 10plus Printer series Quick Reference Guide Regulatory notices continued VCCI Class B Japan CORE FHLB ESESRESAEMAMAS VCCI OHH CHOC VFABWRRMHEBCT COREN JERK CEAT AZE E AMNELTUETH COR EN T7 A TLE T ar SIERLCIIELT ASNSe SERRE Taea DIAM SS CE gt TIE L UINUIRLELTFEL Safety Power cord warning NCI HAS A7 BS E ABRO ESV FRE 172 EZ E 14 MORE CEH RE AL translation Please use the attached power cord The attached power cord is not allowed to use with other product Taiwanese EMI statement AA Get A ABER HAG FRR TM LA RA aS HERA RER ROAR o Chinese EMI Statement D 4 amp PR ARDY KR 4 HS RRHEBARA HRA BK o Sound Germany Ger uschemission Germany LpA lt 70 dB am Arbeitsplatz im Normalbetrieb nach DIN45635 T 19 54 HP Designjet 70 1 10plus Printer series Quick Reference Guide Y DECLARATION OF CONFORMITY ae according to ISO IEC Guide 22 and EN 45014 Supplier s Name Hewlett Packard Company Supplier s Address Avda Graells 501 08174 Sant Cugat del Vall s Barcelona Spain declares that the product Regulatory Model 3 BCLAA 030 1 BCLAA 0302 BCLAA 0408 Product Family HP Designjet Inkjet
26. he output tray aligning it on the right of the output tray with the side that is to be printed on facing down Do not stack multiple sheets here 2 Push the paper as far as it will go into the printer maintaining its alignment to the right Ensure that your hands are flat on the paper and close to the slot and that the paper remains flat If the printer does not catch the paper try again making sure that the leading edge of the paper is flat 3 Press the OK key the upper right key on the front panel The printer will check the alignment of the paper and if it is misaligned it will eject the paper in that case you will have to reload the paper In case you want to change or remove the paper that you have loaded before printing for example to change the type of paper or to use a different input path e Press the Cancel and OK keys at the same time to eject the paper Note that the illustration below shows the HP Designjet 1 10plus Printer series w HP Designjet 70 1 10plus Printer series Quick Reference Guide How do load paper into the input tray Note that the input tray should be extended only when necessary when using paper larger than Legal or A4 size 1 Remove the input tray 2 Litt up the tray cover 3 If the paper you are using is larger than Legal or A4 size move the small tab in the center towards the left so that you can lengthen the tray Then let go of the tab and pull th
27. head and the contacts inside the carriage are dry re insert the printhead by lowering it into place and return the small handle to its lowered position Press down firmly and evenly on both the front and the back of the printhead to make sure it is correctly seated 11 Pull the printhead cover towards you ensuring that the hook at its front edge latches onto the tab and then push it away from you to close the cover 12 Plug in the printer power cable 13 Close the rear part and then the front part of the outer flap 14 We strongly recommend that you perform an alignment check to ensure the best quality printing See How do align printheads on page 31 There must be paper in the tray during alignment you can use your least expensive paper Pre alignment calibrations may take some time especially if multiple printheads have been removed and re inserted Check that the alignment print has a tick on it The tick should be cyan 15 Check that the printhead icon on the front panel is no longer flashing If this is the case the printhead has been re inserted successfully 26 HP Designjet 70 1 10plus Printer series Quick Reference Guide How do replace printheads It one of the printhead icons on the front panel see page 39 is flashing the corresponding printhead has tailed or needs attention Check that the printhead is properly seated and clean the printhead contacts see page 24 If the problem persists repl
28. ies Quick Reference Guide Tell me about the front panel The front panel or control panel of the printer gives information about the status of the printer and also has three keys or buttons that let you control the actions of the printer Note that the illustration below shows the HP Designjet 1 10plus Printer series on the left and the HP Designjet 70 Printer series on the right The numbers correspond to the following elements 1 Display area 2 OK key Indicates to the printer e that you have now loaded paper in the appropriate tray or feed and the printer may start printing e that you have corrected a problem for example you have removed jammed paper or replaced a failing printhead and that the printer should continue with its activity for example it should resume printing e that you want to cut the roll paper if you have a roll feed with roll paper loaded 3 Cancel key Cancels the current operation 4 Attention light The Attention yellow light is on when the printer requires a user action for example to close the top cover if the display is blank 5 Power key Turns the power on and off 6 Power light The Power green light is on when the printer is switched on 42 HP Designjet 70 1 10plus Printer series Quick Reference Guide Tell me about the front panel continued The printer s front panel has a Display area that gives information about the printer The sets
29. ments to the output system to enable output to be stacked e If the output tray has prints stacked in it and you want to print from the roll feed empty the output tray and adjust it as necessary before printing continued on next page 13 HP Designjet 70 1 10plus Printer series Quick Reference Guide Input tray bei B Size C Size Front path Rear Output bin D Size path sheet DIN C4 324mm ISO A2 594mm ISO B4 353mm LEGAL 14 JIS B4 364mm ISO A3 ANSI B ARCH B DIN C3 458mm ANSI B 19 ISO B3 500mm JIS B3 ANSI C TE o Position UP BA e me BE DOWN Closed DOWN Closed o Closed DOWN Closed N A Position Down Closed N A A3 Fosition DOWN Closed N A A3 Position 17x22 Closed Open 5 Position A2 Closed UP Position Roll icon Position Roll icon HP Designjet 70 1 10plus Printer series Quick Reference Guide How do I load a roll of paper 70 Roll paper can be used only if you have the roll feed accessory Note that only one source of paper can be used by the printer at any time So if a roll of paper is loaded in the printer and you want to print to a sheet of paper you must first unload the roll If subsequent jobs require a roll to be used the roll must be loaded again before they can be printed You can cut a roll without unloading it by pressing the OK key the paper first advances about 1 cm
30. njet 70 1 10plus Printer series Quick Reference Guide USB I O failure Unplug power cable wait a few seconds Make sure your USB cable is functioning and less than 3 meters long or connect alternative I O Plug in power cable turn printer on Error code 64 04 General Jetdirect failure Unplug the power cable Remove the HP Jetdirect print server Make sure the cable is functioning and properly connected to printer and network Insert the HP Jetdirect print server into the Error code 04 13 printer plug in power cable and turn printer on If the problem persists please upgrade your HP Jetdirect firmware Upgrades are available from http www hp com support net_printing Network I O failure Unplug power cable wait a few seconds Remove the network card and make sure the cable is functioning and properly connected to printer and computer Plug in power cable and turn Error code 63 04 printer on Parallel I O failure Unplug power cable wait a few seconds Make sure your parallel cable is functioning and properly connected to printer and computer The cable should be less than 5 meters long and should Error code 62 04 be 1284 compliant Plug in power cable and turn printer on It you cannot easily solve the problem run HP Designjet System Maintenance as described on page 41 and access the HP Instant Support Web site This is an automated service in which your computer collects information trom your printer about
31. o the sides of the roll 33 HP Designjet 70 1 10plus Printer series Quick Reference Guide It the printer does not take paper from the input tray 1 Check that you specified the paper source correctly in your print job 2 Check that there is paper in the tray and that it was loaded correcily See How do load paper into the input tray on page 6 Try removing the paper from the tray and reloading it Make sure that there is not too much paper in the tray You should not try to load more than 70 sheets of plain paper 50 sheets of coated paper or 20 sheets of glossy paper in the tray for more details see the HP Designjet Driver and Documentation CD Note that the upper limit marked in the tray of certain models of printer is a theoretical maximum and may not apply to the paper you are usingCheck that the tray is supported by a flat and stable surface Paper loading failure can be caused by curled or damaged paper Keep paper in its box when not using it to avoid this kind of problem It the printer rejects the paper Check that the paper is correctly placed against the right side of the tray When loading paper through the front path always use the OK key to load the sheet before sending the job trom the computer Paper loading failure can be caused by curled or damaged paper Keep paper in its box when not using it to avoid this kind of problem When using the tray check that the adjusters a
32. of icons in the lower two thirds of the display refer respectively to the Black Cyan Magenta and Yellow components of the ink system 43 HP Designjet 70 1 10plus Printer series Quick Reference Guide Tell me about the icons on the front panel The four icons shown here refer to the amount of ink in each of BORO the ink cartridges A flashing printhead icon at the bottom indicates a problem with that printhead ggg Busy When flashing Status of When flashing Printing cancelling Sheet Paper Out of paper or job drying powering paper stalled off The icon flickers if Action Add paper or the top or side cover is clear the paper path open Action close the When off Normal top cover or close the side cover When off Printer is powered off idle or Press a Key When flashing Printer waiting Action Press the OK key When oft Normal awaiting user action Paper When flashing misaligned The paper is misaligned and must be reloaded to print Action Reload the Paper jam When flashing paper Paper jammed paper When off Normal stalled or carriage Status of the When on stalled roll The roll is loaded Action Clear the When flashing The paper jam roll is empty or stuck See page 32 Action Load roll When oft Normal When oft There is no roll loaded Hardware error When flashing Hardware error Action See page 39 When off Normal 44 HP Designjet 70 1
33. on CD for instructions 2 See the HP Designjet Driver and Documentation CD for more intormation about other reasons for a decline in print quality To obtain the best results from your printer it is important that you use only HP approved inks and paper 38 HP Designjet 70 1 10plus Printer series Quick Reference Guide The problem is a flashing tool icon in the front panel If there is a hardware error with your printer this icon flashes on the front panel The precise error is indicated by a pattern of squares displayed in the ink cartridge icons on the front panel Packaging not properly removed or printhead carriage latch not properly closed or cutter badly assembled Error code 86 11 Rear path not correctly installed Error code 35 01 General printer system failure Error code 56 13 General O failure Error code 65 04 39 Turn off the printer Make sure that all packaging is removed and that the printhead carriage latch is properly closed Remove and reinstall the cutter according to the instructions in the User s Guide Remove the rear path then reinstall it see page 32 You may have to press the OK key to clear the error Unplug power cable wait a few seconds plug in power cable and turn printer on If the problem persists call HP support Unplug power cable wait a few seconds Connect alternative O if available plug in power cable turn printer on HP Desig
34. printer e 110x205 mm 4 3 x 8 1 inches and 625 x 1625 mm 24 6 x 63 9 inches AT oversize 1 10plus 1 10plus nr printers 3 The rear path upper slot for single sheets of thick paper or other media between e 76 x 205 mm 4 x 8 1 inches and 458 x 1625 mm 18 03 x 63 9 inches A2 oversize 70 printer e 110 x 205 mm 4 3 x 8 1 inches and 625 x 1625 mm 24 6 x 63 9 inches AT oversize 1 10plus 1 10plus nr printers The rear path upper slot is also used for roll input if your printer has the manual roll feed installed 4 The rear path lower slot is used for roll input if your printer has the Automatic Roll Feed installed HP Designjet 1 10plus nr only HP Designjet 70 1 10plus Printer series Quick Reference Guide The roll feed enables you to load roll paper into the rear path When roll paper is loaded into the printer it obstructs the paper path therefore roll paper must always be unloaded before printing on sheet paper see page 18 However the paper is loaded it should always be loaded in portrait mode the leading edge of the paper should be the shorter edge The extensions may be used to support large sheets of paper going into the front input path and also act as supports for paper arriving in the output tray HP Designjet 70 1 10plus Printer series Quick Reference Guide Note that the illustration below shows the HP Designjet 1 10plus Printer series 1 Place a single sheet of paper in t
35. printhead 32 HP Designjet 70 1 10plus Printer series Quick Reference Guide It paper from the roll is jammed 1 Turn off the printer 2 Check in all places where the roll could be trapped Remove the tront paper tray This will allow you to see inside the printer through a slot in the front Release and remove any trapped paper that is visibly stuck Litt the top cover being caretul not to damage or disturb any of the tubes or other internal parts of the printer If there is any paper trapped in the wheels inside the printer release and remove the paper Unload the roll and remove it from its supports If you are using the 70 Printer series see How do unload a roll of paper 70 on page 17 If you are using the 1 10plus Printer series see How do unload a roll of paper 110plus Printer series on page 21 Remove the rear path by pressing the buttons on each of its sides and pulling it straight out If you don t pull it straight out you may damage the paper sensor If there is any paper trapped in the rollers inside the printer release and remove the paper 3 Once the paper jam has been cleared replace any parts of the printer paper tray top cover roll spindle rear path that you have removed opened making sure they fit securely 4 Turn on the printer 5 Betore reloading the paper roll you must trim the leading edge of the roll such that this edge is perfectly straight and at right angles t
36. re set correctly 34 HP Designjet 70 1 10plus Printer series Quick Reference Guide It the printer picks up two or more sheets together e Check that the paper was loaded correctly into the tray See How do load paper into the input tray on page 6 Try removing the paper from the tray and reloading it e Always fan the paper by its short edge before loading it into the tray Mr a e Check that the paper is not damaged Keep paper in its box when not using it 35 HP Designjet 70 1 10plus Printer series Quick Reference Guide The problem is that the printer has stopped Note that the illustrations below show the 7O Printer series If the front panel looks like this and the yellow light is flashing 1 Open both parts of the hinged flap at the right of the printer lifting it right back so that you can see the print carriage Check that all packaging material has been removed from around the print carriage The carriage may move at this point Wait until it has stopped moving 2 Check that the printhead cover is latched down The printer will not work if the latch is not properly engaged 3 Close the rear part and then the front part of the hinged flap The printer will not work if the flaps are not properly closed 4 If the yellow light has not turned off see the HP Designjet Driver and Documentation CD 36 HP Designjet 70 1 10plus Printer series Quick Reference Guide If yo
37. restrict the ability of a manufacturer to enforce such disclaimers or limitations or 50 HP Designjet 70 1 10plus Printer series Quick Reference Guide HP limited warranty statement continued c Grant the customer additional warranty rights specify the duration of implied warranties which the manufacturer cannot disclaim or not allow limitations on the duration of implied warranties 3 FOR CONSUMER TRANSACTIONS IN AUSTRALIA AND NEW ZEALAND THE TERMS IN THIS WARRANTY STATEMENT EXCEPT TO THE EXTENT LAWFULLY PERMITTED DO NOT EXCLUDE RESTRICT OR MODIFY AND ARE IN ADDITION TO THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE OF HP PRODUCTS TO SUCH CUSTOMERS Revision February 10th 2003 5 1 HP Designjet 70 1 10plus Printer series Quick Reference Guide You can obtain current Material Safety Data Sheets for the ink systems used in the printer by mailing a request to this address Hewlett Packard Customer Information Center 19310 Pruneridge Avenue Dept MSDS Cupertino CA 95014 U S A There is also a Web page http www hp com hpinfo community environment productinfo psis_inkjet htm Regulatory Model Number For regulatory identitication purposes your product is assigned a Regulatory Model Number The Regulatory Model Number for your product is BCLAA 0301 BCLAA 0302 and BCLAA 0408 depending of your product size This regulatory number should not be confused with the marketing name such as HP Designj
38. status and error conditions and sends it to HP Web servers These then display information in your Web browser about how to solve the problems detected Note that you must have an Internet connection to use HP Instant Supportt 40 HP Designjet 70 1 10plus Printer series Quick Reference Guide e For details of how to troubleshoot problems see the topic The Problem ls on the HP Designjet Driver and Documentation CD e For help with completing the installation of your printer see the topic How do I complete assembly and set up on the HP Designjet Driver and Documentation CD e There are notes on clearing jammed paper on page 32 of this guide e f print quality deteriorates you may need to clean your printer Refer to the HP Designjet Driver and Documentation CD for instructions It your computer has all the HP Designjet software installed and an Internet connection you can use the HP Designjet System Maintenance utility to help solve your problem This allows you to connect to the HP Instant Support web site which provides online problem diagnosis For more details of HP Designjet System Maintenance refer to Tell me about HP Designjet System Maintenance on page 46 It HP Instant Support does not help to solve your problem select Troubleshoot tor turther assistance For much more about troubleshooting printer problems see the HP Designjet Driver and Documentation CD 4 HP Designjet 70 1 10plus Printer ser
39. tory notices continued trequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interterence will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult your dealer or an experienced radio TV technician You may find usetul the following booklet prepared by the FCC How to Identity and Resolve Radio TV Interference Problems This booklet is available from the US Government Printing Office Washington DC 20402 Stock No 004 000 00345 4 Normes de s curit Canada Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de Classe B prescrites dans le r glement sur le brouillage radio lectrique dict par le Minist re des Communications du Canada DOC statement Canada This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in t
40. ur printer seems to be ignoring the printing job you have sent to it 1 Check that the printer is correctly connected to the computer It the connection is through a network print the printer s configuration pages hold down the Power key while pressing the OK key four times and check in the TCP IP section that the Status is shown as Ready Make a note of the printer s IP address and subnet mask which are in the same section It the IP address is 0 0 0 0 or 192 0 0 192 refer to your printer s setup poster It the Status is Ready you can use a Web browser to check the network connection between printer and computer Simply type your printer s IP address into your browser where you would normally type a URL If you get a reply from the printer then the network connection between the printer and the computer is working It the Status is Not Ready or if the printer does not reply to the Web browser check that the printer s IP address and subnet mask belong to your network It necessary consult your network administrator Check that the printer queue is not paused 3 If you are using Mac OS X make sure you selected HP IP Printing when you created your printer and not IP Printing 37 HP Designjet 70 1 10plus Printer series Quick Reference Guide It the quality of your prints degrades 1 Check whether you need to clean the printer If this is the case see the HP Designjet Driver and Documentati
41. y top right key on the front panel the paper first advances about 1 cm or 0 4 inch 1 If your printer has a manual roll feed you must set your application to pick paper from the roll teed 2 Select Print from your application 3 Load a roll of the required paper onto the spindle Ensure that the roll is turned the right way with the side on which you wish to print facing up and that the blue stop on the spindle is pushed in against the paper 4 Insert the spindle into its retaining slots with the blue stop on the right A and the black stop on the left B as seen from the rear of the printer Note that the following illustration shows the 11Oplus Printer series with the Automatic Roll Feed fitted HP Designjet 70 1 10plus Printer series Quick Reference Guide How do I load a roll of paper 1 10plus Printer series continued If the paper is glossy we recommend that you wear gloves to avoid smearing the surtace of the paper 5 Make sure that the leading edge of the roll is straight and perpendicular to its side edges 6 Rewind any excess paper so that the paper is rolled tightly onto the spindle 7 Insert the leading edge of the paper into the lower slot in the rear of the printer Push the paper in until it encounters resistance keeping the sides of the paper rolled tightly so that the paper is aligned properly 8 After emitting a beep the printer will take up the paper 9 The
Download Pdf Manuals
Related Search