Hotpoint LI2JDA User's Manual
Contents
1. key OFF ON suction and power selection of suction 1 2 3 power selection of suction 2 2 3 4 power selection of suction 3 Use the high suction speed in cases of concentrated kitchen vapours It is recommended that the cooker hood suction is switched on for 5 minutes prior to cooking and to leave in operation during cooking and for another 15 minutes approximately after terminating cooking If the hood fails to operate correctly briefly disconnect it from the mains power supply foralmost5 sec by pulling outthe plug Then plug itin again andtry once more before contacting the Technical Assistance Service Maintenance Prior to any maintenance operation ensure that the cooker hood is disconnected from the power supply Cleaning the hood The cookerhood should be cleaned regularly internally and externally For cleaning use a cloth moistened with denatured alcohol or neutral liquid detergents Avoid abrasive detergents Warning Failure to carry out the basic standards of the cleaning of the cooker hood and replacement of the filters may cause fire risks Therefore we recommend oserving these instructions Grease filter This mustbe cleaned once a month using non aggressive detergents either by hand or in the dish washer which must be set to a low temperature and a short cycle When washed in a dish washer the grease filter may discolour slightly but this does not affect its filtering capacity Toremove the grease filte2. 65cm for gas or mixed cookers Ifthe appliance is installed above agas cooking device with installation instructions specifying a greater clearance you must take this into account Do not tile grout or silicone this appliance to the wall Surface mounting only The hood is equipped with a top air outlet B for discharge of fumes to the outside Ducting version exhaust pipe and pipe fixing clamps not provided Shoulditnotbe possibleto discharge cooking fumes and vapourtothe outside the hood can be used in thefilter version fitting an activated carbon filter and the deflector F on the support bracket G fumes and vapours are recycled through the top grille H by means of an exhaust pipe connected to the top air outlet B and the connection ring mounted on the deflector F exhaust pipe and pipe fixing clamps not provided The models with no suction motor only operate in ducting mode and must be connected to an external suction device not supplied Installation Fig 4 Preliminary information for installation of the hood Disconnectthe hood during electrical connection by turning the home mains switch off Expansion wall plugs are provided to secure the hood to most types of walls ceilings However a qualified technician must verify pase of the materials in accordance with the type of wall ceiling The wall ceiling must be strong enough to take the weight of the hood Do nottile grout or silicone this appliance to the wall Sur
3. Hotpoint Key Contacts After Sales Service Over 1200 trained specialists directly employed by us ensure that you can have complete confidence in both the appliances and services we offer ESERVICECENTRE Repair Service and Information Desk UK 08709 066 066 Open 8 to 8 Mon Fri 8 to 6 Sat 10 to 4 Sun amp Bank Holidays www hotpointservice co uk Republic of Ireland 1850 302 200 Note Our operators will require the following information Model dci Serial number A Extended Warranties UK 08709 088 088 Open 8 to 8 Mon Sun www hotpointservice co uk Republic of Ireland 1850 502 200 Genuine Parts and Accessories UK 08709 077 077 Open 8 30 to 5 30 Mon Fri amp 9 to 12 Sat www hotpointservice co uk Republic of Ireland 01 842 6836 Merloni Elettrodomestici UK Ltd Morley Way Peterborough PE2 9JB LI2JDA Ed 11 04
4. not play with the appliance WARNING Ensure thatthe appliance is switched off before replacing the lamp to avoid the possibility of electric shock Do not use the cooker hood where the grill is not correctly fixed The suctioned air must not be conveyed in the same channel used for fumes discharged by appliances powered by other than electricity The environment must always be adequately aerated when the cooker hood and other appliances powered by other than electricity are used at the same time Flamb cooking with a cooker hood is prohibited The use of a free flame is damaging to the filters and may cause fire accidents therefore free flame cooking must be avoided Frying of foods must be kept under close control in order to avoid overheated oil catching fire Carry outfumes discharging in accordance with the regulations in force by local laws for safety and technical restrictions E Hotpoint After Sales Service No company is better positioned to offer an after sales serviceon a Hotpoint appliance than us the manufacturer As part of our commitment to you all Hotpoint appliances have the added benefit of a fully inclusive parts and labour guarantee for the first 12 months In addition to this you also have the advantage of free replacement parts for the first 5 years when fitted by a Hotpoint engineer When the 12 months parts and labour guarantee expires we offer the following after sales service options Repair Service a
5. unit If the hood is to be used in ducting version the other end of the pipe must be connected to a device expelling the fumes to the outside If the hood is to be used in filter version then fix the deflector F to the chimney support bracket G and connect the other extremity of the pipe to the connection ring placed on the deflector F 16 Make the electrical connections 17 Apply the chimney stacks and fasten them at the top to the chimney support G 17b using 2 screws 17a 18 Slide the bottom section of the chimney down until it completely covers the suction unit and slots into the housing provided on top of the hood Replace the grease filter s and where foreseen the grease collecting panels and check that the hood is operating correctly NDA Electrical connection The electrical tension must correspond to the tension noted on the label placed inside the cooker hood Connect the electrical plug where provided to the an easily accessible outlet in conformity with local standards in force Where an electrical plug is not provided for direct connection to electrical network place a standards approved bipolar switch with an aperture distance ofnotless than 3mm accessible from the contacts Description of the hood Fig 1 1 Control panel 2 Grease filter 3 Lamp 4 Vapour screen 5 Telescopic chimney 6 Air outlet used for filter version only Operation OO00 1 2 3 4 1 on off light switch 2
6. K Hotpoint kitchen think Instructions for Installation and Use Electric Hood To the Installer Before installation fill in the product details on the back cover of this book The information can be found on the rating plate To the User You must read the instructions prior to installing and using the appliance and then retain them for future reference CE marking certifies that this appliance conforms to the following EEC directives Low Voltage Equipment 72 23 EEC Electromagnetic Compatibility 89 336 EEC Retention of this Instruction Book This Instruction Book must be kept handy for reference as it contains important details on the safe and proper use of the appliance If you sell or pass the appliance to someone else or move house and leave it behind make sure this Book is also provided so the new owner can become familiar with the appliance and safety warnings If the Book is lost or damaged a copy may be obtained from Merloni Elettrodomestici UK Ltd Morley Way Peterborough PE2 9JB BEZ N FR m MIN Consult the designs in the front pages referenced in the text by alphabet letters Closely follow the instructions set out in this manual All responsibility forany eventual inconveniences damages or fires caused by not complying with the instructions in this manual is declined The cooker hood mustbe placed ata minimum distance of 50 cm from the cooking plane for electric cookers and
7. face mounting only Do not fix chimney flue to furniture or fly over shelves unless the chimney flue can be easily removed in case maintenance is ever required Where foreseen remove the grease collecting panels Remove the grease filter s Do not tile grout or silicone this appliance to the wall Surface mounting only Do not fix chimney flue to furniture or fly over shelves unless the chimney flue can be easily removed in case maintenance is ever required Assembling the chimney flue support bracket 3 parts The three parts should be fixed with 4 screws the support extension is adjustable and should correspond to the internal width of the telescopic chimney flue Assembling the deflector only when a deflector composed of 3 parts is supplied the deflector should be only for the filter version The three parts should be fixed with 2 screws the deflector extension is adjustable and should correspond to the width of the chimney flue support to which it is then fixed 1 Using a pencil draw a line on the wall extending up to the ceiling to mark the centre This will facilitate installation 2 Restthe drilling template against the wall the vertical centre line printed on the drilling template must correspond to the centre line drawn on the wall and the bottom edge of the drilling template must correspond to the bottom edge of the hood bear in mind that when installation is complete the underside of t
8. he hood must be atleast 50 cm above the cooker top in the case of electric cookers and at least 65 cm above the cooker top in the case of gas or mixed cookers 3 Rest the support bracket on the drilling template so that it coincides with the dotted rectangle mark the two outer holes and drill them remove the drilling template insert 2 wall plugs and fix the hood support bracket into place using two 5x45mm screws Hang the hood on the bracket Adjust the distance of the hood from the wall Adjust the horizontal position of the hood Using a pencil mark the cooker hood permanent drill hole inside the suction group two drill holes are necessary for fastening 8 Remove the hood from the bracket 9 Drill at the point marked Z8mm see operation 7 10 Insert 2 wall plugs 11 Rest the chimney support bracket G against the wall touching the ceiling Use the support bracket as a drilling template the small slotformed on the support must coincide with the line drawn onthe wall as above operation 1 and mark 2 holes with a pencil drill the holes 08mm insert 2 wall plugs 12 Fix the chimney support bracket to the wall using two 5x45mm screws 13 Hook the hood onto the bottom bracket 14 Fix the hood into its final position on the wall ABSOLUTELY ESSENTIAL 15 Connect a pipe pipe and pipe clamps not provided to be purchased separately for discharge of fumes to the connection ring located over the suction motor
9. nd Information Help Desk UK 08709 066066 www hotpointservice co uk Republic of Ireland 1850 302 200 Note Our operators will require the Model number and the Serial number of your appliance Available 364 days a year with a fast effective and value for money service We have the largest white goods repair service in the UK with over 1000 of our own fully trained engineers All repairs include a parts and labour guarantee for 12 months from the date of the repair Ifyou require any information or have any questions about your appliance our operators are on hand with help and advice All this ensures that you will receive the best available after sales service possible Extended Warranties UK 08709 088 088 www hotpointservice co uk Republic of Ireland 1850 502 200 Whether you have just one or a number of Hotpoint appliances in your kitchen we offer two service cover plans to give you total peace of mind Repair Protection Plan FREE service repairs for a single Hotpoint appliance during the period of cover Kitchen Cover FREE service repairs for all your Hotpoint appliances less than 8 years old Genuine Parts and Accessories UK 08709 077 077 www hotpointservice co uk Republic of Ireland 01 842 6836 A wide range of genuine parts and accessories are available from our hotline or through our website Genuine parts and accessories extended warranties and service repairs are all available on our web site at BB
10. r pull the spring release handle f Fig 1 Charcoal filter filter version only It absorbs unpleasant odours caused by cooking The charcoal filter can be washed once every two months using hot water anda suitable detergent orin a dish washerat65 C ifthe dish washer is used select the full cycle function and leave dishes out Eliminate excess water without damaging the filter then remove the mattress located inside the plastic frame and put it in the oven for 10 minutes at 100 C to dry completely Replace the mattress every 3 years and when the cloth is damaged Remove the filter holder frame by turning the knobs g 90 that affix the chimney to the cooker hood Fig 2 Insertthe pad i of activated carbon into the frame h and fitthe whole back into its housing j Replacing lamps Fig 3 Warning Prior to touching the light bulbs ensure they are cooled down 1 Extract the guard by levering it off with a small screwdriver or similar tool 2 Replace the damaged light bulb Only use halogen bulbs of 20W max G4 making sure you do not touch them with your hands 3 Close the lamp cover it will snap shut If the lights do not work make sure that the lamps are fitted properly into their housings before you call for technical assistance The appliance is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do
Download Pdf Manuals
Related Search