Hotpoint CRO 642 D B User's Manual
Contents
1. COOKING ZONE POWER PROGRAMME LOCK button SELECTOR buttons TIMER button TIMER DECREASE indicator light TIME button e INCREASE TIME button increases the time value e PROGRAMME TIMER display shows which set on the timer see Start up and use programme has been selected see Start up and use e DECREASE TIME button decreases the time value set on the timer see Start up and use e COOKING ZONE PROGRAMMED indicator lights show which cooking zones are being used during e COOKING ZONE SELECTOR button shows a a cooking programme see Start up and use particular cooking zone has been selected and therefore various adjustments are possible e CONTROL PANEL LOCK button prevents accidental changes to the hob settings see Start e COOKING ZONE SELECTOR button is used to up and use select the desired cooking zone e CONTROL PANEL LOCK indicator light shows e POWER indicator provides a visual display for the the control panel has been locked see Start up current heat level and use e ON OFF button switches the appliance on and off e COOKING ZONE POWER SELECTOR buttons switch on the hotplate and control the power see e ON OFF indicator light shows whether the Start uo and use appliance is on or off e TIMER indicator light shows that the timer has e PROGRAMME TIMER button controls the cooking been activated programme times see Start up and use Extendable cooking zones Certain models are fitted with extendable cooking z2. a lever under the side tabs of the cover see Terminal board picture 3 Loosen the cable clamp screw and the terminal board screws in accordance with the type of connection required and position the connection supports as shown in the following table and diagrams 4 Position the wires in accordance with the information given in the following table and diagrams and connect the appliance by tightening all the screws for the springs as much as possible Voltage and Electrical connections Terminal board board mains frequency 5 Secure the power supply cable by fastening the cable clamp screw then put the cover back on Phase Phase Phase Earth Neutral U bolt connection support Connecting the electricity supply cable to the mains If the appliance is being connected directly to the electricity mains an omnipolar switch must be installed with a minimum opening of 3 mm between contacts The installer must ensure that the correct electrical connection has been made and that it is fully compliant with safety regulations Before connecting the appliance to the power supply make sure that e The appliance is earthed and the plug is compliant with the law e The socket can withstand the maximum power of the appliance which is indicated on the data plate located on the appliance itself e The voltage falls within the range of values indicated on the data plate e The socket is compatible with the pl
3. E Hotpoint Ss Safety switch The appliance has a safety switch which automatically switches the cooking zones off after they have been in operation for a certain amount of time at a particular power level When the safety switch has been triggered the display shows O For example the right rear hotplate is set to 5 and will switch off after 5 hours of continuous operation while the front left hotplate is set to 2 and will switch off after 8 hours Maximum operating Power level time in hours a a Oo 6 Buzzer This can also indicate several irregularities e An object a pan cutlery etc has been placed on the control panel for more than 10 seconds e Something has been spilt on the control panel e A button has been pressed for too long All of the above situations may cause the buzzer to sound Remove the cause of the malfunction to stop the buzzer If the cause of the problem is not removed the buzzer will Keep sounding and the hob will switch off o Practical cooking advice 10 Very high flame High flame D i O o O E amp T E oO D Low flame cooking Very low flame Pressure cooking Pressure cooker Cooking on a high flame and browning roasts steaks escalopes fish fillets fried eggs Fast thickening liquid juices Boiling water pasta rice vegetables Milk Bain marie cooking Pressure cooking after whist
4. animals or may damage property Built in appliance Use a suitable cabinet to ensure that the appliance functions properly e The supporting surface must be heat resistant up to a temperature of approximately 100 C e If the appliance is to be installed above an oven the oven must be equipped with a forced ventilation cooling system e Avoid installing the hob above a dishwasher if this cannot be avoided place a waterproof separation device between the two appliances e Depending on the hob you want to install the cabinet must have the following dimensions see figure Ventilation To allow adequate ventilation and to avoid overheating of the surrounding surfaces the hob should be positioned as follows e At a minimum distance of 40 mm from the back panel e So that a minimum distance of 20 mm is maintained between the installation cavity and the cabinet underneath e Kitchen cabinets adjacent to the appliance and taller than the top of the hob must be at least 600 mm from the edge of the hob FAN ASSISTED OVEN min 40 mm gt FRONT SIDE i K OF HOB l NOs z UNDERSIDE 3 OF HOB ay mi ms O Fixing The appliance must be installed on a perfectly level supporting surface Any deformities caused by improper fixing could affect the features and operation of the hob The thickness of the supporting surface should be taken into account when choosing the
5. button for a few moments the indicator light will switch off and the lock function will be removed Switching off the hob Press the D button to switch the appliance off If the control panel lock has been activated the controls will continue to be locked even after the hob is switched on again In order to switch the hob on again you must first remove the lock function Demo mode It is possible to set the hob to a demonstration mode where all the controls work normally but the heating elements do not switch on To activate the demo mode the hob must be switched on with all the hotplates switched off e Press and hold the and buttons simultaneously for 6 seconds When the 6 seconds have elapsed the ON OFF and CONTROLS LOCKED indicator lights will flash for one second Release the and buttons and oress the Q button e The display will show the text DE and MO and the hob will be switched off e When the hob is switched on again it will be set to the demo mode To exit this mode follow the procedure described above The display will show the text DE and OF and the hob will be switched off When it is next switched on the hob will function normally Practical advice on using the appliance To obtain the best results from your hob e Use pans with a thick flat base in order to fully utilise the cooking zone X e Always use pans with a diameter which is large enough to cover the
6. cleaning it is advisable to rinse the surface well and dry it thoroughly If water is spilt on the surface dry it quickly and thoroughly Some hobs have an aluminium frame which is similar to stainless steel Do not use any cleaning or degreasing products which are not suitable for use with aluminium Disassembling the hob If it is necessary to disassemble the hob 1 Loosen the screws fixing the alignment springs on each side 2 Loosen the screws holding the fixing hooks in each corner 3 Take the hob out of its installation cavity Do not attempt to repair the appliance yourself If the appliance breaks down contact a Service Centre Technical description of the models E Hotpoint This table provides a model by model list of the energy absorption values tyoe of heating elements and diameters of each cooking zone Hobs _CRO642DB_ ____ CCROA2DOB Cooking zone Back Left 210 140 Back Right 145 Front Left H 1200 H 1200 145 Front Right HD 1700 700 180 120 HO 2400 1500 170x260 Total power 6500 7000 Key H single hilight HO oval hilight HD double hilight 13 we After Sales Service No company is better positioned to offer an after sales service on a Hotpoint appliance than us the manufacturer As part of our commitment to you all Hotpoint appliances have the added benefit of a fully inclusive parts and labour guarantee for the first 12 months In addition to this you also have th
7. crack or even break if hit with a sharp object such as a tool If this happens disconnect the appliance from the electricity mains immediately and contact a Service Centre e Ensure that power supply cables of other electrical appliances do not come into contact with the hot parts of the hob e Remember that the cooking zones remain relatively hot for at least thirty minutes after they have been switched off An indicator light provides a warning when residual heat is present see Start up and use e Keep any object which could melt away from the hob for example plastic and aluminium objects or products with a high sugar content Be especially careful when using plastic film and aluminium foil or packaging if placed on surfaces which are still hot they may cause serious damage to the hob amp Hotpoint e Always make sure that pan handles are turned towards the centre of the hob in order to avoid accidental burns e When unplugging the appliance always pull the plug from the mains socket do not pull on the cable e Never perform any cleaning or maintenance work without having disconnected the appliance from the electricity mains e The appliance should not be operated by people including children with reduced physical sensory or mental capacities by inexperienced individuals or by anyone who is not familiar with the product These individuals should at the very least be Supervised by someone who assumes responsibil
8. hotplate fully in order to use all the available heat e Make sure that the base of the cookware Is always clean and dry in order to fully utilise and extend the life of both the cooking zones and the cookware e Avoid using the same cookware which has been used on gas burners the heat concentration on gas burners may distort the base of the pan causing it not to adhere correctly Safety devices Pan sensor Each cooking zone is equipped with a pan sensor device The hotplate only emits heat when a pan with suitable measurements for the cooking zone is placed on it If the indicator light is flashing it may indicate e An incompatible pan e A pan whose diameter is too small e The pan has been removed from the hotplate Residual heat indicators Each cooking zone is equipped with a residual heat indicator This indicator signals which cooking zones are still at a high temperature If the power display f 7 shows tt the cooking zone is still hot It is possible for example to keep a dish warm or melt butter or chocolate As the cooking zone cools the power display will show I The display switches off when the cooking zone has cooled sufficiently Overheating protection If the electronic elements overheat the hob switches off automatically and VT appears on the display followed by a flashing number When the temperature has reached a suitable level this message disappears and the hob may be used again
9. length of the screws for the fixing hooks e 30 mm thick 17 5 mm screws e 40 mm thick 7 5 mm screws Fix the hob as follows 1 Use short flat bottomed screws to fix the 4 alignment springs in the holes provided at the central point of each side of the hob 2 Place the hob in the cavity make sure It is in a central position and push down on the whole perimeter until the hob is stuck to the supporting surface 3 For hobs with raised sides After inserting the hob into its cavity insert the 4 fixing hooks each has its own pin into the lower edges of the hob using the long pointed screws to fix them in place until the glass is stuck to the supporting surface The screws for the alignment springs must remain accessible In order to adhere to safety standards the appliance must not come into contact with electrical parts once it has been installed All parts which ensure the safe operation of the appliance must not be removable without the aid of a tool Electrical connection The electrical connection for the hob and for any built in oven must be carried out separately both for safety purposes and to make extracting the oven easier Terminal board On the lower part of the appliance there is a connection box for the different types of electricity supply the picture is only an indication and is not an exact representation of the SI purchased model UNDERSIDE OF HOB K Hotpoint Single ph
10. A wide range of genuine parts and accessories are available from our hotline or through our web site Genuine parts and accessories extended warranties and service repairs are all available on our web site at SERVICECENTRE www theservicecentre co uk 14 amp Hotpoint Guarantee Satisfaction guaranteed or your money back We give you a unique satisfaction guaranteed promise valid for 90 days after you have purchased your Hotpoint appliance If there is a technical problem simply call Hotpoint Repair service or visit our web site at www theservicecentre co uk and where necessary we will arrange for an engineer to call If the technical problem is not resolved under this guarantee we will replace your machine or if you prefer give you your money back All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well as free replacement parts for the first 5 years except microwaves selected integrated appliances and cooker hoods which have a one year guarantee provided that they are fitted by a Hotpoint engineer Guarantee terms and conditions Your guarantee is only applicable in the United Kingdom or Republic of Ireland and is subject to the following provisions that your appliance Has been installed and used correctly in accordance with this instruction booklet O Has been used solely for domestic purposes and is located on domestic premises ie not for commercial or trade
11. Operating Instructions HOB English 1 CRO 642DB CRO 742 DOB K Hotpoint Contents Installation 2 4 Positioning Electrical connection Description of the appliance 5 6 Control panel Extendable cooking zones Start up and use 7 10 Switching on the hob Switching on the cooking zones Switching off the cooking zones Power function Heating elements Programming the cooking duration Timer Control panel lock Switching off the hob Demo mode Practical advice on using the appliance Safety devices Practical cooking advice Precautions and tips 11 General safety Disposal Care and maintenance 12 switching the appliance off Cleaning the appliance Disassembling the hob Technical description of the models 13 After Sales Service 14 Guarantee 15 Key Contacts 16 Installation Before operating your new appliance please read this instruction booklet carefully It contains important information concerning the safe operation installation and maintenance of the appliance Please keep these operating instructions for future reference Pass them on to any new owners of the appliance Positioning Keep all packaging material out of the reach of children It may present a choking or suffocation hazard see Precautions and tips The appliance must be installed by a qualified professional in accordance with the instructions provided Incorrect installation may cause harm to people and
12. ase connection The hob is equipped with a pre connected electricity supply cable which is designed for single phase connection Connect the wires in accordance with the instructions given in the following table and diagrams Voltage and Electrical cable Wire connection mains frequency yellow green 230 240V 1 N p N the two blue wires 220 240V 1 N N together 50 60 Hz L brown and black together Other types of connection If the mains supply corresponds with one of the following Voltage and mains frequency e 400V 2 N 50 60 Hz e 220 240V 3 50 60 Hz e 230 240V 3 50 60 Hz e 400V 2 2N 50 60 Hz Separate the wires and connect them in accordance with the instructions given in the following table and diagrams Voltage and i Electrical l Wire connection mains frequenc ectrical cable 400V 2 N p o yellow green SOBO Fz a N N the two blue wires together 230 240V 3 L1 black 220 240V 3 50 60Hz L2 brown yellow green N1 blue 400V 2 2N N2 blue 50 60 Hz L1 black L2 brown If the mains supply corresponds with one of the following Voltage and mains frequency e 400V 3 N 50 60 Hz proceed as follows The cable provided is not suitable for the following types of installation 1 Use a suitable supply cable HOSRR F or higher with the right dimensions cable cross section 25 mm 2 To open the terminal board use a screwdriver as
13. atch the surface beyond repair Never use steam cleaners or pressure cleaners on the appliance e t is usually sufficient simply to wash the hob using a damp sponge and dry it with absorbent kitchen towel e f the hob is particularly dirty rub it with a special glass ceramic cleaning product then rinse well and dry thoroughly e To remove more stubborn dirt use a suitable scraper Remove spills as soon as possible without waiting for the appliance to cool to avoid residues forming crusty deposits You can achieve excellent results by using a rust proof steel wire sponge specifically designed for glass ceramic surfaces soaked in soapy water e f any plastic or sugary substances are accidentally melted on the hob remove them immediately with the scraper while the surface is still hot e Once it is clean the hob may be treated with a special protective maintenance product the invisible film left by this product protects the Surface from drips during cooking This maintenance task should be carried out while the appliance is warm not hot or cold e Always remember to rinse the appliance well with clean water and dry it thoroughly residues can become encrusted during subsequent cooking processes 12 Stainless steel frame only in models with outer frame stainless steel can be marked by hard water which has been left on the surface for a long time or by cleaning products containing phosphorus After
14. cooking zones Each cooking zone is controlled using a selector button and a power adjustment device consisting of power level selector buttons between the values of O and 9 e To begin operating a cooking zone press the corresponding control button and set the desired power level using the power level selector buttons between 0 and 9 Switching off the cooking zones To switch off a cooking zone select it using the corresponding selector button and e Press power level selector button O this immediately returns the power setting to O and the cooking zone switches off Power function The power function for the cooking zones may be used to shorten heating up times Activate and set the power level for the desired cooking zone as described in the previous paragraph Press and hold the selector button corresponding to the desired cooking zone for at least 2 seconds The display the power level indicator will alternately show the letter P and the power level set previously until the desired power level has been E Hotpoint reached Once this level has been reached the display will revert to showing the set power level To deactivate this function press and hold for at least 2 seconds the selector button corresponding to the cooking zone on which the function has been activated alternatively select a different power level between O and 9 using the power level selector buttons Heating elemen
15. d will be switched on To display the time remaining for the other programmed hotplates press the Q button repeatedly The times remaining for each hotplate will be shown in a clockwise order beginning with the front left hotplate Changing the programme 1 Press the button repeatedly until the duration you wish to change is shown 2 Use the Q buttons to set the new duration 3 Confirm by pressing the Q button To cancel a programme follow the above instructions At step 2 press the button the duration decreases progressively until it reaches O and switches off The programme resets and the display exits programming mode Timer The hob must be switched on The timer can be used to set a duration up to 99 minutes 1 Press the Q programming button until the timer indicator light is illuminated 2 Set the desired duration using the 7 and buttons 3 Confirm by pressing the Q button The timer begins counting down immediately When the time has elapsed a buzzer will sound for one minute Control panel lock When the hob is switched on it is possible to lock the oven controls in order to avoid accidental changes being made to the settings by children during cleaning etc Press the o button to lock the control panel the indicator light above the button will switch on To use any of the controls e g to stop cooking you must switch off this function Press the o
16. d Warranties UK 08709 088 088 Open 8 to 8 Mon Sun www theservicecentre co uk Republic of Ireland 1850 502 200 Genuine Parts and Accessories UK 08709 077 077 Open 8 30 to 5 30 Mon Fri amp 9 to 12 Sat www theservicecentre co uk Republic of Ireland 01 842 6836 Indesit Company UK Ltd Morley Way Peterborough PE2 9JB 16
17. e advantage of free replacement parts for the first 5 years when fitted by a Hotpoint engineer When the 12 months parts and labour guarantee expires we offer the following after sales service options Repair Service and Information Helo Desk UK 08709 066066 www theservicecentre co uk Republic of Ireland 1850 302 200 Note Our operators will require the Model number and the Serial number of your appliance Available 364 days a year with a fast effective and value for money service We have the largest white goods repair service in the UK with over 1200 of our own fully trained engineers All repairs include a parts and labour guarantee for 12 months from the date of the repair If you require any information or have any questions about your appliance our operators are on hand with help and advice All this ensures that you will receive the best available after sales service possible Extended Warranties UK 08709 088 088 www theservicecentre co uk Republic of Ireland 1850 502 200 Whether you have just one or a number of Hotpoint appliances in your kitchen we offer two service cover plans to give you total peace of mind Repair Protection Plan FREE service repairs for a single Hotpoint appliance during the period of cover Kitchen Cover FREE service repairs for all your Hotpoint appliances less than 8 years old Genuine Parts and AccessoriesUK 08709 077 077 www theservicecentre co uk Republic of Ireland 01 842 6836
18. ity for their safety or receive preliminary instructions relating to the operation of the appliance e Do not look at the halogen lamps in the cooking zones for long if they are present e Do not let children play with the appliance Disposal X e When disposing of packaging material observe local legislation so that the packaging may be reused e The European Directive 2002 96 EC relating to Waste Electrical and Electronic Equipment WEEE states that household appliances should not be disposed of using the normal solid urban waste cycle Exhausted appliances should be collected separately in order to optimise the cost of re using and recycling the materials inside the machine while preventing potential damage to the atmosphere and to public health The crossed out dustbin is marked on all products to remind the owner of their obligations regarding separated waste collection For further information relating to the correct disposal of exhausted household appliances owners may contact the public service provided or their local dealer 11 Care and maintenance Switching the appliance off Disconnect your appliance from the electricity supply before carrying out any work on it Cleaning the appliance Do not use abrasive or corrosive detergents for example products in spray cans for cleaning barbecues and ovens stain removers anti rust products powder detergents or sponges with abrasive surfaces these may scr
19. le P PN U LO Low flame cookin stews Reheating dishes L UJ Chocolate sauce Keeping food hot Precautions and tips This appliance has been designed and manufactured in compliance with international safety standards The following warnings are provided for safety reasons and must be read carefully C This appliance conforms to the following European Economic Community directives 2006 95 EEC dated 12 12 06 Low Voltage and subsequent amendments 89 336 EEC dated 03 05 89 Electromagnetic Compatibility and subsequent amendments 93 68 EEC dated 22 07 93 and subsequent amendments General safety Make sure that the air inlet behind the fan grille is never obstructed The built in hob should in fact be provided with suitable ventilation for the cooling of the electronic components used in the appliance e The appliance was designed for domestic use inside the home and is not intended for commercial or industrial use e The appliance must not be installed outdoors even in covered areas It is extremely dangerous to leave the appliance exposed to rain and Storms e Do not touch the appliance when barefoot or with wet or damp hands and feet e The appliance must be used by adults only for the preparation of food in accordance with the instructions provided in this booklet Do not use the hob as a worktop or chopping board e The glass ceramic hob is resistant to mechanical shocks but it may
20. ones These may be circular or oval and may vary in their extensibility they may be double or triple hotplates A list of controls is given below these controls are only present in models with the extendable cooking zone option Circular extendable hotplate DOUBLE HOTPLATE ON indicator light DOUBLE HOTPLATE ON button e DOUBLE HOTPLATE ON button switches on the double hotplate see Start up and use e DOUBLE HOTPLATE ON indicator light shows the double hotplate has been switched on Oval extendable hotplate OVAL HOTPLATE ON indicator light oO LI OVAL PLATE ON button e OVAL HOTPLATE ON button switches on the oval hotplate see Start uo and use e OVAL HOTPLATE ON indicator light shows the oval hotplate has been switched on Start up and use The glue applied on the gaskets leaves traces of grease on the glass Before using the appliance we recommend you remove these with a special non abrasive cleaning product During the first few hours of use there may be a smell of rubber which will disappear very quickly A few seconds after the hob is connected to the electricity supply a buzzer will sound The hob may now be switched on If the 7 or button is pressed for an extended period of time the display scrolls quickly though the power levels and timer minutes Switching on the hob To switch the hob on press and hold the C1 button for approximately one second Switching on the
21. ts Two types of heating element may be installed depending on the appliance model halogen and radiant elements Halogen elements emit heat via radiation from the halogen lamps they contain They have similar properties to gas burners they are easy to control and reach set temperatures quickly allowing you to see the power level instantly Radiant elements consist of a series of coils which allow heat to be distributed evenly at the base of the cookware so that all slow flame cooking may be performed successfully for example stews Sauces or reheated dishes Programming the cooking duration All the cooking zones may be programmed simultaneously for a duration between 1 and 99 minutes 1 Select the cooking zone using the corresponding selector button 2 Adjust the temperature 3 Press the Q programming button 4 Set the cooking duration using the 7 and T buttons 5 Confirm by pressing the Q button The timer begins counting down immediately A buzzer sounds for approximately 1 minute and the cooking zone switches off when the set programme has finished Repeat the above procedure for each hotplate you wish to programme Using multiple programmes and the display If one or more hotplates are programmed the display will show the data for the hotplate with the least time remaining and the light corresponding to the position of the hotplate will flash The lights corresponding to the other hotplates programme
22. ug of the appliance If the socket is incompatible with the plug ask an authorised technician to replace it Do not use extension cords or multiple sockets Once the appliance has been installed the power supply cable and the electrical socket must be easily accessible The cable must not be bent or compressed The cable must be checked regularly and replaced by authorised technicians only The manufacturer declines any liability should these safety measures not be observed Do not remove or replace the power supply cable for any reason Its removal or replacement will void the warranty and the CE marking INDESIT does not assume liability for accidents or damage arising from replacement removal of the original power supply cable Replacement can only be accepted when carried out by personnel authorised by INDESIT and using an original spare part Description of the appliance E Hotpoint Control panel The control panel described in this manual is only a representative example it may not exactly match the panel on your appliance PROGRAMME TIMER display COOKING ZONE PROGRAMMED INCREASE TIME indicator light button POWER and COOKING ZONE ON OFF RESIDUAL HEAT SELECTED indicator light button indicators g g e g g ee Je comme FO B FD EO O omer SELECTOR buttons es 38 EA indicator light fa fa Fal Ea fa Ca Ea El gt comans oe vi a a indicator light CONTROL PANEL
23. use Has been properly connected to a suitable electrical supply voltage as stated on the appliance rating plate Has not been subject to misuse accident modified or repaired by anyone other than one of our own service engineers aXe For pre purchase information on any other Hotpoint product call 08701 50 60 70 or visit www hotpoint co uk D Recycling amp Disposal Information As part of Hotpoint s continued commitment to helping the environment Hotpoint reserves the right to use quality recycled components to keep down customer costs and minimise material wastage Please dispose of packaging and old appliances carefully To minimise risk of injury to children remove the door plug and cut mains cable off flush with the appliance Dispose of these parts separately to ensure that the appliance can no longer be plugged into a mains socket and the door cannot be locked shut 15 04 2008 195069881 00 XEROX BUSINESS SERVICES Key Contacts After Sales Service Over 1200 trained specialists directly employed by us ensure that you can have complete confidence in both the appliances and services we offer SERVICECENTRE Repair Service and Information Desk UK 08709 066 066 Open 8 to 8 Mon Fri 8 to 6 Sat 10 to 4 Sun amp Bank Holidays www theservicecentre co uk Republic of Ireland 1850 302 200 Note Our operators will require the following information Model number Serial number Extende
Download Pdf Manuals
Related Search