Hornet Car Security 564T User's Manual
Contents
1. d and simultaneously You will hear a screen for five seconds note If the ignition is on the temperature check clock mode will not work timer mode 36 By pressing the remote i and LA buttons the parking lights will flash 4 times and then start the vehicle and run for the set duration The remote start can be shut off by the remote by pressing the remote start button and remain in timer mode but if any other shut down zones or the ignition becomes active the timer mode will cancel 1 Press Timer mode buttons 2 The vehicle will confirm with 4 parking light flashes 3 A 1 second delay will start O 2004 directed electronics inc 4 The system will start the car and will run for the specified duration unless shut down by the remote start button If shut down with the remote start button 8 amp the system will remain in timer mode 5 The system will start every 3 hours until canceled by the brake hood or neutral safety shut down wires important Timer Mode should be used only in open areas Never start and run the vehicle in an enclosed space such as a garage or carport To exit timer mode turn the ignition switch on any time the engine is running The parking lights will flash 4 times indi cating timer mode has been exited Safety features o o This system has several important safety features to ensure proper2. D and P Buttons When pressed simultaneously these buttons activate battery saver mode which will drop power consumption on the trans ceiver battery to zero when the alarm is inactive or disarmed Standard LCD 2 way icon configuration 12 The vehicle interior temperature icon displays the temperature of the inside of the vehicle when prompted 8 88 Icon The numeric display icon will show the hours and minutes M Icon The AM PM icon indicates the time before or after noon ry Icon The alarm clock mode icon indicates that the alarm clock mode is active 2004 directed electronics inc Icon The timer function icon flashes during timed functions including parking timer CE ico The transmit range indicator icon stays visible as long as the system is within operating range Icon The remote transmission indicator icon displays when the trans ceiver is transmitting a signal Icon The vibrate beep mode icon appears when the transceiver is set to vibrate mode Icon The power saver mode can be turned on or off with the trans ceiver This icon displays the status Icon The remote start timer mode icon indicates the 24 hour autostart feature is active and automatically remote starts 24 hours from the time activated Icon The VRS mode icon has no function Icon The vehicle page mode icon displays when the alarm module is paging the transceiv
3. Model 564T Owner s Guide Hornet limited lifetime consumer warranty For a period of one calendar year from the date of purchase of this auto security device Directed Electronics Inc promises to the ORIGINAL PURCHASER to repair or replace with a comparable reconditioned model free of cost any electronic control module which proves to be defective in workmanship or material under normal use SO LONG AS THE SYSTEM WAS SOLD INSTALLED AND SERVICED BY A PROFES SIONAL AUTO INSTALLER AND REMAINS IN THE CAR IN WHICH THE SYS TEM WAS ORIGINALLY INSTALLED If warranty service is necessary you must have a clear copy of your sales receipt containing all of the information shown on the follow ing page After the first calendar year from the date of purchase of this auto security device Directed Electronics Inc promises to the ORIGINAL PURCHASER to repair or replace with a comparable reconditioned model any electronic control module which proves to be defective in workmanship or material under normal use FOR A CHARGE OF 45 00 SO LONG AS THE SYSTEM WAS SOLD INSTALLED AND SERVICED BY A PROFESSIONAL AUTO INSTALLER AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLED If warranty service is necessary you must have a clear copy of your sales receipt containing all of the information shown on the following page This warranty contains the entire agreement relating to warranty and supersedes all pre vious and cont
4. minutes This allows the system s timer to conveniently cool down the turbo after you have left the vehicle To activate 1l Park the vehicle and set parking brake 2 Remove your foot from the brake pedal and leave the engine running 3 Press and release the sk and buttons at the same time 4 The lights will flash to indicate the remote start has entered short run turbo mode 5 Turn off the key the engine will keep running 6 Exit and secure the vehicle 7 The engine will turn off after the programmed run time setting the clock To set the clock press and hold D for five seconds the trans ceiver will chirp twice and the hour selection will start flashing y Immediately press AUX to advance the hour selection or to reverse the hour selection Once the correct hour is displayed press D again and the minute selection will start flashing O 2004 directed electronics inc 35 Then press AUX to advance the minute selection or to reverse the minute selection Once the correct time is displayed simply stop pressing any buttons for 10 seconds and the trans ceiver will automatically exit the clock mode temperature check mode This system will report the interior temperature of your vehicle with the press of two buttons To activate the temperature display press A melody and the interior temperature will appear on the LCD
5. you will hear one siren chirp to indicate arming and a second siren chirp to indi cate Bypass Notification A Bypass Notification chirp means that the security system ignores the input that was active when the system was armed until that input ceases Three seconds after that input ceases the security system will resume normal monitoring For example if your vehicle has an interior light exit delay and you arm your security system before the interior light turns off you may hear a second Bypass Notification chirp Once the light turns off however the security system resumes normal monitoring note Bypass Notification does not occur when the sys tem is in Silent Mode or if the notification chirps have been programmed off by the installer disarming diagnostics Extra chirps that are heard when disarming the system are the Tamper Alert If four chirps are heard when disarming the system then the security system was triggered in your absence If five chirps are heard when disarming the system a zone was trig gered so many times that the Nuisance Protection Circuitry has bypassed that zone In either case the status LED will indicate which zone was involved see Table of Zones section The secu rity system will retain this information in its memory and chirp four or five times each time it is disarmed until the next time that the ignition is turned on O 2004 directed electronics inc 41 system status chirps The sire
6. Disarm Unlock Button 19 Remote Start Indicator 20 Hood Trunk Open or Trigger Indicator 21 Panic Mode Button 22 Valet Mode Indicator 23 Remote Start Safety Shutdown Indicator 24 Battery Level Indicator 25 Auxiliary Button 26 Temperature Controlled Remote Start Indicator 27 Silent Arm Disarm Mode Indicator 28 Full Trigger Alert Indicator 29 Arm Disarm Indicator 30 Function Button 31 Celsius Fahrenheit Indicator O 2004 directed electronics inc standard 4 button configuration B controls the Arm and Panic On Off function om dl controls the Disarm and Panic Off function AUN controls Silent Mode and Auxiliary channel 2 output controls the Remote Start function and ue pressed together control the Timer mode AUX and pressed together control Turbo Short Run B and AUX pressed together control channel 4 output d and AUX pressed together control channel 5 output O 2004 directed electronics inc 5 what is included A control module An ASK transceiver antenna One four button remote One 2 way LCD remote A Stinger TM DoubleGuard two stage shock sensor A Revenger Soft Chirp six tone programmable siren A status LED indicator light A push button Valet switch Your warranty registration VV NN ON ON ON ON ON ON A shut down toggle switch Congratulations on the purchase of your combination remote start alarm system Due to the complexity of this system it must be in
7. be added Power Window Control Automatic power window control is pro vided with the 529 T and 530T systems These can operate power windows and can roll them up automatically when the system is armed roll them down or both up and down Mobile Video This system is compatible with Directed Video s MCB1000 Multi Channel Controller featuring on screen secu rity system programming and zone trigger information O 2004 directed electronics inc glossary of terms Control Unit The brain of your system Usually hidden under neath the dash area of the vehicle The control unit houses the microprocessor which monitors your vehicle and controls all system functions Fault Proof Starter Interrupt An automatic switch controlled by your system that prevents the vehicle s starter from cranking whenever the system is armed The vehicle is never prevented from cranking when the system is disarmed in Valet mode or if the starter interrupt switch itself fails Your system has feature ready circuitry for the starter interrupt however installation may require additional labor Input A physical connection to the system An input can be provided by a sensor pinswitch or by existing systems in the vehicle such as ignition or courtesy lights LED A red light mounted at a discretionary location inside the vehicle It is used to indicate the status of your system Shock Sensor This system has a dual zone shock sensor T
8. half its normal rate decreasing the system s current draw gt Power Saver in Valet Mode When the system enters Valet Mode the LED illuminates steadily If the vehicle is not used ignition is not turned on for a one hour period while the system is in Valet Mode the LED will shut off If the system remains in Valet Mode the LED will come back on the next time the ignition is turned on and then back off i 46 Programming options control your system s normal operational set up Most options do not require additional parts but some may require installation labor The following is a list of the programmable options with the factory settings in Bold gt Active arming from remote only or passive arming auto matic arming 30 seconds after the last door has been closed gt Arming disarming siren chirps on or off 2004 directed electronics inc gt The ignition controlled door lock feature on or off When this feature is programmed on the doors will lock three seconds after the ignition is turned on and unlock when the ignition is turned off If your installer is programming the security system with the Directed Bitwriter ignition lock and unlock are independent features that can be programmed separately gt Passive door locking with passive arming or active door locking only when arming with the remote Passive locking allows the vehicle s doors to lock when the security system passively arms after
9. is programmed on the starter of the vehicle will be disabled 30 seconds after the ignition is turned off Once the key is turned off the LED will flash slowly one half its normal armed rate to indicate the AED arming cycle Thirty seconds later the starter will be disabled To start the car it will be necessary to disarm the system with the remote It is also possible to disarm the AED feature by turning the ignition key to the RUN position and pressing the Valet button the programmed number of times AED is also disabled when the system is in Valet mode note This feature will only function if the FailSafe Starter Kill relay has been installed gt Siren tones and chirp volume The output of the Revenger Soft Chirp siren consists of six different tones in sequence Any of these tones can be eliminated by a dealer resulting in a unique easily identifiable siren sound The chirps can be either full volume or 6 decibels quieter than the full alarm blast O 2004 directed electronics inc gt The engine can be programmed to run for any duration ranging from 1 to 60 minutes 12 minutes is the default After the programmed run time the engine will shut down and will not restart unless in Timer Mode While the remote start system is running the engine the parking lights of the vehicle can flash on and off or come on and light steadily security amp convenience expansions Listed below are some of the many expan
10. operation of the motor and prevent accidental damage to the engine or its components starter anti grind circuitry Whenever the vehicle is remote started advanced anti grind circuitry prevents the starter from engaging even if the key is turned to the start position This prevents damage to the starter motor if the key is turned to the start position during remote start operation 2004 directed electronics inc 37 disabling the remote start system This feature allows your system s remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally This feature is useful if the vehicle is being serviced or stored in an enclosed area To disable the remote start move the shutdown toggle switch to the OFF position The switch can be installed in a location of your choice Check with your installer for recommended locations Location of Shutdown Switch over and under rev protection The system monitors the engine speed and will automatically shut the engine off if the RPMs rise above or fall below the programmed levels This feature prevents damage to the motor due to fuel delivery system failures or other problems which may cause the engine to race note The system uses an input from the vehicle to sense engine speed This wire must be connected in order for over and under rev protection to work shut down inputs 38 This security system uses several inputs to shu
11. the 30 second countdown This feature only works if passive arming has been programmed gt Panic mode enabled disabled when the ignition is turned on Some states have laws against sirens sounding in moving cars gt Forced passive arming on or off If your security system is programmed for passive arming and the forced passive arming feature has been programmed on the system will passively arm after one hour even if a protected entry has been left open Forced passive arming ensures that the system will be armed if a door has accidentally been left ajar when leaving the vehicle note When the system passively arms after one hour the entry point that has been left open and anything con nected to the same zone is bypassed and cannot trigger the system However the remaining inputs to the system are fully operational O 2004 directed electronics inc 47 gt Full trigger response 30 or 60 seconds This determines how long the full triggered sequence lasts Some states have laws regulating how long a security system can sound before it is considered a nuisance If your installer is programming the security system with the Directed Bitwriter the full triggered response can be programmed for any duration ranging from 1 to 180 seconds gt Automatic Engine Disable AED on or off The purpose of this feature is to protect the vehicle from being stolen at all times regardless of whether or not the alarm is armed If AED
12. the remote start shuts down 4 In gasoline vehicles the engine will start 4 seconds after the parking lights flash In diesel vehicles the engine will start when the WAIT TO START indicator on the vehicle s dash goes out 2004 directed electronics inc 5 Once the vehicle has started it will run for the pre program med period of time either 12 24 or 60 minutes see Programming Options section of this guide or until a shut down input is triggered important It is unsafe to operate a vehicles motor in a garage or other closed off area Breathing the exhaust from the vehicle is hazardous to your health Never acti vate the remote start in an enclosed space When you are ready to drive the vehicle El Jj 3 No 2 1 Insert the ignition key and turn it to the ON not START po X sition 2 Press the brake pedal note If the brake pedal is pressed before the key is in the ON position the engine will shut down While the vehicle is running during remote start operation the system will monitor the vehicle and will automatically shut down the engine if the system receives any of the following shut down inputs Yo vV NON The brake pedal is pressed The hood is opened The shutdown toggle switch is put into the OFF position The pre programmed run time 12 24 or 60 minutes has elapsed Remote button sk is pressed twice within 3 seconds The L
13. CD 2 way remote will generate a page notification with a O 2004 directed electronics inc 33 unique melody or vibrate and the remote start icon 19 will turn off when the remote start shuts down valet take over 34 The Valet Take Over feature allows the vehicle to remain running after the key has been removed from the ignition This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time but would like to leave the motor running and the climate controls on To perform Valet Take Over 1 Before turning off the engine press and release sk twice within 3 seconds on the remote or press and release the optional momentary switch Then wait five seconds A remote start page notification with a unique melody or vibration will be generated and the LCD 2 way remote will display the remote start icon 19 as long as the vehicle is running Then wait three seconds 2 urn the ignition key to the OFF position The engine will stay running 3 The engine will run until the pre programmed time elapses or a shut down input is received See the previous Remote Start section for a complete list of shut down inputs note This feature will not work if the brake pedal is being pressed O 2004 directed electronics inc short run turbo Short run turbo mode keeps the engine running after arriving at you destination for a programmable period of 1 3 5 or 10
14. SI 41 system status CHILPS tc lo de eg ad ras ii is 42 table Gh ZONES yo iia AA A A 42 interpreting zone diagnostics sisse 43 code hopping dc vere EY a wees Sn da erai oe deans 44 high frequency cose verc sles ted tie Pa eee Bede nee eee 44 OWNER recognition dd ao o nes UTR 45 rapid resume logic cit is cde Sele Bank EUR eC voee ze pd 45 powersavermode 2s eee diate 5 8s eed rr a I mee i RIPE HR mes 46 programming options eeeeeee hh n 46 security amp convenience expansions iiis nnn 49 glossary of terms 3 344 009 bu xe prec R EE I UE DUREE UC UE ERR ER 51 2 O 2004 directed electronics inc remote configurations LCD 2 way configuration Esp elle HE E Aa P OTST Te IPS TPS IPS TS PS Te lo le ls le Sello less le Fe fo BE O 2004 directed electronics inc 3 1 Vehicle Interior Temperature Indicator 2 Numeric Display 3 AM PM Indicator 4 Alarm Clock Mode Indicator 5 Timer Function Indicator 6 Transmit Range Indicator 7 Transmission Indication 8 Vibrate Beep Mode Indicator 9 Power Saver Mode Indicator 10 Remote Start Timer Mode Indicator 11 No Function 12 Vehicle Page Mode Indicator 13 Full Trigger Shock Sensor Indicator 14 Hood Trunk Open or Trigger Indicator 15 Parking Light Indicator 16 Door Open or Trigger Indicator 17 Arm Lock Button 18
15. THEREWITH THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO THE EXCLUSION OF ANY AND ALL WARRANTY OF MERCHANTABILITY AND OR ANY AND ALL WAR RANTY OF FITNESS FOR A PARTICULAR PURPOSE AND OR ANY AND ALL WARRANTY OF NON INFRINGEMENT OF PATENTS IN THE UNITED STATES OF AMERICA AND OR ABROAD NEITHER THE MANUFACTURER OR ANY ENTITIES CONNECTED THEREWITH SHALL BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMIT ED TO ANY CONSEQUENTIAL DAMAGES INCIDENTAL DAMAGES TOW ING REPAIR REPLACEMENT DAMAGES FOR LOSS OF TIME LOSS OF EARNINGS COMMERCIAL LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON TROL MODULE AS DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or con sequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state IMPORTANT NOTE This product warranty is automatically void if its date code or serial number is defaced missing or altered This warranty will not be valid unless you have completed the war ranty card and mailed it to Directed Electronics Inc within 10 days after purchase to the address listed on the warranty registration card Make sure you have all of the following information from your dealer A clear copy of the sales receipt showing the
16. aFE npo eds a ESL dL de Mod i ttes ee CH 23 warn away response description sisse 24 triggered response description 25 multi level security arming 0 0 cece eee eee 26 arming while driving ccc coe esee E E etes Go em eA T 27 disarming ai Er exe mee ESUPUCEP OS CC p E Rees ae Ios 28 disarming while driving ssseeeeeeee e 28 lugh secunty dismi pa ESEPPOT 28 disarming without a remote lssseeeeee cece eee 29 silent mod s sven A ence soie e DR Paseo eye quus 30 panic moder Ain dues ce alc vie CR tese Peers eS ERAS 30 valet mode 59 A O da dtd uU Mod al der 31 TEMOtE STE E AN USE VM TUNE Cep d ies Beaters 32 valet takeover on reri xus ese 6rd INO Reb Na a Sein 34 short run t rbo iudicet id Decet RR Cent egeret 35 setting the clock cce vere pP VERE e Ope eem do 35 temperature check mode sssseeeeee eh 36 timer modes reet eni Bm qe ial nr eie e DEOR Ayn 36 safety features ciis c dd Rec rtr re Ede rrr TP RP Ren 37 starter anti grind circuitry sese ee 37 disabling the remote start system 6 0 6 eee eee 38 O 2004 directed electronics inc 1 over and under rev protection sese 38 shutdown inputs 2 2 uda eere ett n Le ee se a e hs 38 nuisance prevention circuitry ciis n 39 24 hour timer mode 4 ses erte LR a a 40 diagnostics n ooo eG PUE pu EAE NN IUE ener tahoe PE ERE Rn 40 arming diagnostics pebeeeeo ek v kr km ct EE siete D ORNREREDQ EE 41 disarming diagnostics A
17. area or partially enclosed area without ventilation such as a garage When parking in an enclosed or partially enclosed area or when having the vehicle serviced the remote start system must be disabled using the installed toggle switch It is the user s sole respon sibility to properly handle and keep out of reach from chil dren all remote controls to assure that the system does not O 2004 directed electronics inc unintentionally remote start the vehicle THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED These precautions are the sole responsibility of the user gt Use of this product in a manner contrary to its intended mode of operation may result in property damage personal injury or death 1 Never remotely start the vehicle with the vehicle in gear and 2 Never remotely start the vehicle with the keys in the ignition The user must also have the neutral safety feature of the vehicle periodically checked wherein the vehicle must not remotely start while the car is in gear This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in the product installation guide If the vehicle starts in gear cease remote start operation immediately and consult with the authorized Directed dealer to f
18. attery CR2032 that will last approximately one year under normal use When the battery begins to weaken operating range will be reduced and the LED on the remote will dim O 2004 directed electronics inc 7 your warranty Your warranty registration must be completely filled out and returned within 10 days of purchase Your product warranty will not be validated if your warranty registration is not returned Make sure you receive the warranty registration from your dealer It is also necessary to keep your proof of purchase which reflects that the product was installed by an authorized dealer fcc id notice This device complies with Part 15 of FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesirable operation Directed Electronics Inc 544 Series C Tested to Comply with FCC Standards Directed Electronics Inc 4771 Series Tested to Comply C with FCC Standards 8 O 2004 directed electronics inc Directed Electronics Inc 474V P S Series Tested to Comply C with FCC Standards Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device caution This product is designed for fuel injected automatic transmission vehicles only Use of this product in a s
19. cating that the system is actively protecting your vehicle If you hear a second chirp after arming and note that the status LED is flashing in groups see the Diagnostics Section of this guide This extra chirp is called Bypass Notification 2004 directed electronics inc passive arming The system can be programmed to arm itself automatically called passive arming If the system is programmed for passive arming it will automatically arm 30 seconds after the ignition is turned off and the system detects that you have left the vehicle by opening and closing a door Whenever the system is in its 30 second passive arming countdown the status LED will flash twice as fast as it does when the system is armed At the 20 second point of the count down the siren will chirp to indicate that the system is about to arm At the 30 second point the parking lights will flash to indicate that the system is armed note If any protected entry point such as a door or a switch protected trunk or hood is open the system will not passively arm unless forced passive arming is pro grammed on See Programming Options section Addi tionally each time a sensor is triggered during the arming countdown the 30 second countdown starts over When armed your vehicle is protected as follows gt Light impacts trigger the Warn Away signal When triggered the siren chirps and the parking lights flash for a few seconds gt Heavy impacts tri
20. ceiver The high frequency combined with Binary Data communication achieves superior range with two way communication system signal paging features A page is the signal the control module sends to the transceiver as confirmation of receipt of a command or alarm system status When the transceiver receives a page it will generate a page notifi cation to the user notifications are audible beeps or the remote vibrates and the LCD icons will display the current system status Command Page When a command arm disarm remote start or auxiliary channel from the transceiver is sent and received the system will send a command page back to confirm receipt O 2004 directed electronics inc 19 Page Recognition Mode The transceiver will leave a zone icon illuminated when it has received a triggered response and will wait for violation recogni tion Press any button on the transceiver the LCD information and alarm page alerts will be cleared note The transceiver buttons will not send a command to the system until the alarm page is cleared warning safety first The following safety warnings must be observed at all times 20 gt Due to the complexity of this system installation of this product must only be performed by an authorized Directed dealer When properly installed this system can start the vehicle via a command signal from the remote control Therefore never operate the system in an enclosed
21. e on off 9 Times Lon ore Remote Start On E 10 times O 2004 directed electronics inc 5 Selections Melody Selection 2 1 2 3 4 5 10 Min Parking D 6 1 Time z O 10 Melody Count Down Mode 20 Min Parking 2 Times x 2 20 Melody Count Down Mode 30 Min Parking E 8 3 Times W J ez0 Melody Count Down Mode 60 Min Parking D B 4 Times X oo Melody Count Down Mode 90 Min Parking amp 5 Times X 1 30 Melody Count Down Mode 120 Min Parking 6 Times 2 08 Melody Count Down Mode Parking Count Down D GE 7 Times z 0 00 Melody Off Mode Alarm Clock Mode D AUX rey 8 88 Melody On Off Celsius Fahrenheit 9 AUX or Melody Select Mode This function will operate in the disarmed state only The AUX button will advance the selection upward The 4 but ton will advance the selection downward or select the off setting Be sure to hold E down for five seconds prior to entering timer clock adjust mode operation Press once to have the alarm clock on Press twice to have the alarm clock off 4 button remote standard configuration Button The arming and panic functions are controlled b
22. e system is controlled by pressing these buttons simultaneously for one second AUX and x Buttons When pressed simultaneously these buttons activate the second unlock or other accessory A and Buttons When pressed simultaneously these buttons activate remote start timer mode engaging the remote start function every 24 hours E and AUX Buttons When pressed simultaneously these buttons display the internal temperature of the vehicle on the LCD d and k Buttons When pressed simultaneously with the system armed the system enters temperature auto start mode and automatically remote starts the vehicle if the temperature inside the vehicle drops below 0 degrees Fahrenheit note Disarming the system while in temperature auto start mode will cause the system to exit this mode D and AUX Buttons The numeric display toggles between the time of the day and the alarm clock when these buttons are pressed simultaneously O 2004 directed electronics inc 11 E and sk Buttons Press these buttons simultaneously to activate the parking timer Each additional press will toggle through the available options 10 min 20 min 30 min 1 hour 1 5 hours 2 hours and off D and d Buttons When pressed simultaneously these buttons toggle between beep notification and vibrate notification
23. e trigger ceases O 2004 directed electronics inc 39 note Arming and disarming the system does not reset this function The only ways to reset a for it to not trigger for 60 minutes or to turn on the igni tion If testing your system it is important to remember that the NPC programming can cause zones to be bypassed and appear to stop working heard when disarming NPC has been engaged If you the ignition on wish to clear the NPC memory turn bypassed zone are If five chirps are 24 hour timer mode To enter timer mode press and simultaneously The 2 way remote will produce a melody and the clock indicator will appear on the remote s LCD Once in Timer Mode the system will remote start every 24 hours Repeat this procedure to turn Timer Mode off The microprocessor at the heart of your system is constantly 40 monitoring all of the switches and sensors connected to it It is designed to detect any faulty switches and sensors and prevents them from disabling the entire system The microprocessor will also record and report any triggers that occurred during your absence Refer to the System Status Chirps and Table of Zones sections of this guide for diagnostic information O 2004 directed electronics inc arming diagnostics If the security system is armed at the same time that an input is active such as a door opening or sensor triggering
24. em while driving press on your remote while the vehicle is running The system will chirp once and then once more to indicate that the ignition is on Disarming M To disarm press rA You will hear two chirps and the parking lights will flash twice High security disarm M For high security disarm press on your remote and the siren will stop sounding To completely disarm the security system press again and the system will chirp 4 or 5 times reporting the trigger Disarming without a remote M Turn on the ignition Press the Valet button within 15 seconds The system should now disarm If it does not you may have waited too long so turn the ignition off and on and try again Silent Mode WB Pressing briefly before arming or disarming will eliminate the confirma tion chirp s for that one operation only Panic Mode B Press for 2 seconds and you will enter Panic Mode The siren will sound and the IB lights will flash for 30 seconds To stop Panic Mode at any time press on the remote again To remote start the vehicle B Pres twice within 3 seconds The parking lights will turn on if connected and the vehicle will start and run for the programmed period of time To disable the remote start system M To disable the remote start move the shutdown toggle switch to the OFF position Location of Valet switch Number of Valet switch pulses for disarming O 2004 directed electronics inc 53 The company behind
25. emporaneous representations or understandings whether written or oral IN ANY EVENT DIRECTED ELECTRONICS INC IS NOT LIABLE FOR THE THEFT OF THE VEHICLE AND OR ITS CONTENTS This warranty is void if the product has been damaged by accident unreasonable use neglect improper service or other causes not arising out of defects in materials or con struction This warranty is nontransferable and does not apply to any unit that has been modified or used in a manner contrary to its intended purpose and does not cover bat teries The unit in question must be returned to the manufacturer postage prepaid This warranty does not cover labor costs for the removal diagnosis troubleshooting or rein stallation of the unit For service on an out of warranty product a flat rate fee by model is charged Contact your authorized dealer to obtain the service charge for your unit These systems are a deterrent against possible theft Directed Electronics Inc is not offer ing a guarantee or insuring against the theft of the automobile or its contents and dis claims any liability for the theft of the vehicle and or its contents Directed Electronics does not authorize any person to create for it any other obligation or liability in connec tion with this security system O 2004 directed electronics inc i TO THE MAXIMUM EXTENT ALLOWED BY LAW ANY AND ALL WAR RANTIES ARE EXCLUDED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COMMERCE
26. ence in case the system is accidentally triggered disarming without a remote If your remote is lost or damaged you can manually disarm your vehicle security system To disarm the system without a remote you must have the vehicle s ignition key and know where the Valet button is located Be sure to check with your installer at the time of installation for both the location and the preset response 1 5 presses of the Valet button To disarm the security system turn the ignition to the ON posi tion Press the Valet button the preset number of times one to five times within 15 seconds After five seconds the system will disarm If the system does not disarm you may have waited too long turn the ignition off and on and try again Location of Valet Button Number of Presses important The Valet button can be programmed to respond to 1 5 presses for the disarm function You must check with the installer to verify the programming for your individual unit O 2004 directed electronics inc 29 silent mode To temporarily turn off the arm or disarm chirps use Silent Mode M Simply press aux for less than one second before arming or disarming and the confirmation chirp s will be elim inated for that one operation only If you want the arm disarm chirps turned off permanently your dealer can do this for you note The Warn Away response to lighter impacts is bypassed if the system is armed u
27. er O 2004 directed electronics inc 13 14 ET The full trigger shock sensor icon indicates that the shock sensor has been triggered by a hard shock The hood trunk open or trigger icon illuminates when the hood or trunk trigger has been activated or the hood or trunk is open and bypasses those zones until it is closed Icon The parking light icon will flash twice when armed or disarmed The icon also flashes during WarnAway and at the beginning and end of remote start cycles The door open or trigger icon illuminates when the door trigger has been activated or the door is open and bypasses that zone until it is closed E ion The remote start icon indicates when the vehicle is remotely started FZZ ico The Valet mode icon appears when the system is in Valet mode Icon The remote start safety shut down icon indicates the vehicle may be in gear or other unsafe condition inhibiting remote start operation O 2004 directed electronics inc The battery level icon indicates the level of power remaining in the battery The temperature controlled remote start icon indicates that the system has entered the temperature remote start mode and auto matically starts the vehicle if the temperature of the vehicle drops below 0 degrees Fahrenheit bl 4 4 pS Icon The silent arm disarm icon appears when the system has been armed or disarmed in the silent mode Icon The full trigger ale
28. following Date of purchase Your full name and address Authorized dealer s company name and address Type of alarm installed Year make model and color of the automobile Automobile license number Vehicle identification number All security options installed on automobile VV VN N NON VV Installation receipts ii O 2004 directed electronics inc table of contents gt limited lifetime consumer warranty lesse e i remote configurations ss essees i ee Hen 3 LCD 2 way configuration i e cece teens 3 standard 4 button configuration oooooocoooocccccc eee 5 Whats included a A asadas 6 important information ssssseseee hmm nnn 6 System MAINTENANCE zs ee esce eee xg ted 7 YOUI WALtanty ose steven e nee ads Eng os ase ene A UV Pe RICE 8 fee id NOTICE cie peo m Pleas a E A IA A A LE YN Rr 8 CalitlOt os ee SML uM uA T E Mu ru pde ter Ue ab tU 9 i mot functions ss An eats o Etre TS aee ee de s 10 LCD 2 way remote standard configuration 0 00000 eee eee 10 Standard LCD 2 way icon configuration 0 0 00 cece eee eee 12 button remote standard configuration ooooooocococoocooooano eee 17 LCD 2 way remote operation 6 6 cece cece ec cette eee e nee e ees 19 system signal paging features 0 0 eee ees 19 using your SYSTEM 1 cee eee ete hen 20 warningl safety Hrste sr aee ste teet tbc eec pb e edge prs 20 active A Cose er Roue A EN UTE eeu A etek UE 22 PASSIVE
29. gger alert icon 28 will turn on for 15 seconds O 2004 directed electronics inc 25 The zone icons will turn on and remain on until a transceiver button is pressed clearing the page alert gt The transceiver will enter page recognition mode and generate alarm page alerts note Icons 13 14 16 and 20 represent alarm system triggered sequence zone inputs For more information about icons and the zones they represent refer to the Standard Remote Configurations section multi level security arming 26 Multi Level Security Arming allows you to select which of the system s inputs or sensors will be active and which will be bypassed when the system is armed See Table of Zones section of this guide Pressing only in Standard Configuration again within five seconds of arming the system will activate the Multi Level Security feature Each time is pressed again a different security level is selected The different security levels are selected as follows a Press once The siren chirps once The system is armed a gt Press a second time within five seconds The siren chirps twice followed by a long chirp Zone 2 is now bypassed gt Press a third time within five seconds The siren chirps three times followed by a long chirp Zone 4 is now bypassed gt Press a fourth time within five seconds The siren chirps four times followed by a long chirp Zones 2 and 4 are now bypassed gt Press Ala f
30. his sensor is mounted in the vehicle and designed to pick up impacts to the vehicle or glass LCD 2 Way Remote A hand held transceiver which operates and monitors the various functions of your system O 2004 directed electronics inc 51 52 Trigger or Triggered Sequence This is what happens when the alarm goes off or trips The triggered sequence of your system consists of the siren sounding and parking lights flashing for the programmed duration Valet Button A small push button switch mounted at a discre tionary location inside the vehicle It is used to override the starter interrupt when a remote is lost or damaged or to enter or exit Valet Mode Warning Zone Response Lighter impacts to the vehicle will generate the Warning Zone response It consists of several seconds of siren chirps and parking light flashes Zone A zone is a separate input that the alarm can recognize as unique Each input to the system is connected to a particular zone Often two or more inputs may share the same zone O 2004 directed electronics inc Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet P 2 2 AQ QUICK REFERENCE GUIDE Arming E To arm press A When the system arms you will hear a short chirp and the parking lights will flash once Arming while driving M To arm the syst
31. ifth time within five seconds The siren chirps 2004 directed electronics inc five times followed by a long chirp All input zones except the ignition are now bypassed note Multi Level Security Arming only applies to a sin gle arming cycle Once the system is disarmed and then re armed all the zones will be active again arming while driving Your security system can be armed while driving the vehicle Simply press on the remote for two seconds while the vehicle is running The siren will chirp once to indicate that the security system is armed and then once more to indicate that the ignition is on The system will not respond to any input except the door triggers and the starter kill relay if installed will not be activated Once you have arrived at your destination the system will disarm when the ignition is turned off The siren will chirp twice and the LED will then stop flashing The system can also be disarmed at any time by pressing e The LCD 2 way remote will beep once or vibrate and the arm icon 29 will be displayed on the LCD note If the transceiver received a Warn Away or triggered response page while armed the first press of the unlock button will clear the page alert A second press will turn the siren off and a third press will disarm the system O 2004 directed electronics inc 27 disarming To disarm the security system press d You will hear two chirps and the pa
32. ix the problem gt After the remote start module has been installed contact your authorized dealer to have him or her test the remote start module by performing the Safety Check outlined in the product installation guide If the vehicle starts when performing the Neutral Safety Shutdown Circuit test the remote start unit has not been properly installed The remote start module must be removed or the installer must properly O 2004 directed electronics inc 21 reinstall the remote start system so that the vehicle does not start in gear All installations must be performed by an autho rized Directed dealer OPERATION OF THE REMOTE START MODULEIF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPER ATION OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY YOU MUST IMMEDIATELY CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AUTHO RIZED DIRECTED DEALER TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS active arming 22 You can arm the system by pressing al of your remote for one second When the system arms you will hear a short siren sound or chirp and see the parking lights flash once If the power door locks are controlled by the system the doors will also lock While the system is armed the status LED will flash approximately once per second indi
33. n memory If your system has been triggered but the LED has been reset by turning on the ignition your dealer can still recall the last two zones that were triggered Contact your dealer for details O 2004 directed electronics inc 43 code hopping The receiver and remotes use a mathematical formula called an algorithm to change their code each time the remote is used This technology has been developed to increase the security of the unit The control unit knows what the next codes should be This helps to keep the remote in sync with the control unit even if you use the remote control out of range of the vehicle However if the remote has been pressed many times out of range of the vehicle or the battery has been removed it may fall out of sync with the control unit and fail to operate the system To re sync the remote simply press several times within range of the vehicle The alarm will automatically re sync and respond to the remote normally high frequency 1 1 44 Your system transmits and receives at 434 MHz This provides a cleaner spectrum with less interference and a more stable signal Enjoy a phenomenal increase in range even in areas with high radio interference O 2004 directed electronics inc owner recognition Owner Recognition is a revolutionary new feature available only from Directed Using a Directed Bitwriter hand held program ming tool your dealer can program many of the s
34. n will chirp when arming disarming the system The pattern of chirps will audibly report the system s status as described below Action Number of Chirps Description Arm 1 System armed Arm 1 3 second delay 1 System armed with Bypass Notification Disarm 2 System disarmed Disarm 4 System disarmed with Tamper Alert Disarm 5 System disarmed NPC active table of zones A zone is represented by the number of LED flashes used by the system to identify a particular type of input Standard input assignments are listed in the following table along with spaces to write in any optional sensors or switches that have been installed 42 O 2004 directed electronics inc ZONE Number of DEALER INSTALLED LED Flashes DESCRIPTION OPTIONS 1 Trunk Pin 2 Instant trigger a heavier impact detected by the shock sensor 3 Door switch trigger 4 Instant trigger for optional sensors 5 Ignition trigger 6 Hood Pin interpreting zone diagnostics Warn Away responses are not reported by arming or disarming diagnostics If you receive a Bypass notification when arming or a Tamper Alert notification when disarming look at the LED Active or triggered zones will be indicated by a pattern of blinks by the LED Example If zone 3 was active or triggered the LED will blink three times with a two second pause Then it will blink three times again and repeat until the ignition is turned on note Your system stores the last two triggered zones i
35. ns section 24 O 2004 directed electronics inc triggered response description A Triggered Response can be activated by any of the triggers listed below and consists of an alarm page along with the response described for each trigger The default Triggered Response dura tion is 30 seconds but can be programmed from 1 180 seconds by your installer with the Directed Bitwriter Sensor Trigger Heavy impacts to the vehicle will instantly sound the siren and flash the lights for the programmed duration and report Zone 2 Door Trigger If a door is opened the siren will chirp for three seconds then the siren will sound and the lights will flash for the programmed duration and report Zone 3 The three seconds allow the user time to disarm the system with a minimum of noise should a door be opened inadvertently while the system is armed Hood Trigger Opening the hood will sound the siren flash the lights for the programmed duration and report Zone 1 Trunk Trigger Opening the trunk if connected will instantly sound the siren and flash the lights for the programmed duration and report Zone 4 Ignition Trigger If the ignition is turned on the siren will chirp for three seconds then the siren will sound and the lights will flash for the programmed duration and report Zone 5 When a Triggered Response is activated the transceiver will Repeat four quick beeps or vibrate for 15 seconds The full tri
36. p a Triggered Sequence The sequence consists of the siren sounding continuously and the parking lights flashing for a pre programmed period which can range in duration from 1 to 180 seconds gt If a door is opened the system will immediately start chirping the siren and flashing the parking lights Three seconds later the siren output changes to a continuous blast This progressive response gives you time to disarm the system with your remote if you inadvertently open the door while O 2004 directed electronics inc 23 the system is armed while still providing instant response even if the door is immediately closed Turning on the ignition key will trip the same progressive re sponse as opening a door The optional starter kill prevents the vehicles starter from cranking warn away response description A Warn Away Response consists of an alarm page along with the responses described below Shock Sensor Light impacts to the vehicle will flash the vehicle lights and chirp the siren for a few seconds Remote Control Notification Ten quick beeps or one vibration Remote Control LCD The full trigger alert icon 28 will dimly illuminate for two seconds The transceiver will enter Page Recognition Mode and operate alarm page alerts note Icons 13 and 14 represent alarm system zone inputs For more information about icons and the zones they represent refer to the Standard Remote Configuratio
37. rking lights will flash twice If the power locks are controlled by the system the doors will also unlock The siren chirping either four or five times when disarming indicates Tamper Alert which is described in the Diagnostics Section of this guide disarming while driving Press d on the LCD 2 way remote or simply turn off the igni tion to disarm the system The lights will flash twice the doors will unlock the siren will chirp twice and the status LED will turn off The 2 way remote will beep twice or vibrate The disarm icon 29 will be displayed on the LCD high security disarm 28 This security system offers High Security Disarm High Security Disarm is a feature that makes it possible to silence and reset the system while it is triggering without disarming the system If the system is triggered and the siren has been sounding for longer n than six seconds pressing on the remote will stop the trigger and return the unit to the armed state The system will not disarm but rather reset This prevents you from disabling the system should you wish to disarm it without visually checking the vehicle Pressing d after resetting the system will disarm the system pressing this button during the first six O 2004 directed electronics inc seconds of the triggered sequence will disarm the security system immediately The six second timer is provided for your conve ni
38. rt icon illuminates when the security system has been triggered by a heavy impact door trigger violation optional sensor violation or a hood trunk trigger C The arm icon appears when the vehicle is armed and locked The disarm icon appears when the vehicle is disarmed and unlocked E Icon Celsius Fahrenheit icon indicates the current mode of the displayed temperature either in Celsius or Fahrenheit O 2004 directed electronics inc 15 16 Standard LCD 2 way button functions Audible Function Button Icon Indication Lamp On E 10 sec Power Saver Mode D A Melody Beep Vibrate Mode d 4 Vibrations 1 Beep Time Adjust O for 5 Seconds 8 88 2 Beeps Mode hour Time Adjust E 1 Time 8 88 Mode min Alarm Clock E 2 Times amp 9 58 Set Mode hour Alarm Clock E 3 Times O ts 88 Set Mode min Alarm Clock Music 4 Times yay 8 5 Selections or Power on Music 1 2 3 4 5 Selection Alarm Clock Adjust 5 Times O Mode on off Timer Count Down Adjust Mode hour e 6 Times Timer Count Down Adjust Mode min E 7 Times Timer Count Down Ending Melody Selection 1 9 8 Times 5 Selections 1 2 3 4 5 x e RS Timer Count Down Mod
39. sing Silent Mode This ensures that no chirps will be emitted by the siren in an area you want chirp free The system is still fully capable of triggering Only the Warn Away response is bypassed panic mode 30 If you are threatened in or near your vehicle you can attract attention by triggering the system with your remote Just press for two seconds and you will enter Panic Mode The siren will sound and the parking lights will flash for the programmed siren duration To stop Panic Mode at any time press on the remote again note Once panic mode has been entered the siren will sound for the programmed duration The LCD 2 way remote will beep or vibrate continuously when the system enters panic mode The 2 way remote will not generate a page notification when panic mode is exited O 2004 directed electronics inc valet mode You can prevent your security system from automatically arming and triggering by using Valet Mode This is very useful when washing the vehicle or having it serviced In Valet Mode the security system will not arm even with the remote but all convenience functions door locks trunk release etc will continue to work normally To enter or exit Valet Mode 1 Turn the ignition on Turn the ignition off i 3 No Y DD N Press and release the Valet button within 10 seconds The status LED will light solidly if you are entering Valet Mode and it will go out if
40. sion options available Please consult your dealer for a complete explanation of all the options available to you Audio Sensor Metal on glass glass cracking and breaking glass produce distinctive acoustic signatures The 506T audio sensor uses a microphone to pick up sounds then analyzes them with proprietary acoustic software to determine if the glass has been struck Backup Battery The 520T keeps the system armed triggers the alarm and keeps the starter interrupt active if main battery is dis connected Hood Lock Prevents the vehicles hood from being opened without a key keeping thieves away from the system s siren the battery connections and other components under the hood Field Disturbance Sensor An invisible dome of coverage is estab lished by installing the 508D radar sensor Your system can O 2004 directed electronics inc 49 50 react to any intrusions into this field with the full triggered Sequence Power Locks This system offers lock outputs that can control some manufacturers power door lock systems For other systems additional parts may be required Power Trunk Release The accessory output of the system can op erate a factory power release for the vehicles trunk or hatch Although the on board relay can control most power trunk re leases sometimes an optional relay is required If the factory release is not power activated Directed s 522T trunk release solenoid can often
41. stalled by an authorized dealer only Installation of this product by anyone other than an authorized dealer voids the warranty All dealers are provided with a preprinted dealer certif icate to verify authorization By carefully reading this Owner s Guide prior to using your system you will maximize the use of this system and its features You can print additional or replacement copies of this manual by accessing our web site at www directed com 6 O 2004 directed electronics inc system maintenance The system requires no specific maintenance other than battery replacement for the remotes LCD 2 Way Remote Battery Replacement The 2 way remote is powered by a 1 5V AAA battery The Battery Level indicator has three level indicators that serve as a visual indication of battery charge When the battery reaches a low charge level that requires replacement the transceiver will generate a single notification chirp and the Battery Level indi cator will flash continuously BRE P FULL REPLACE EMPTY To replace the battery gently pull the battery cover release tab then slide the door down to expose the battery and remove the expired battery Place the new battery into the transceiver observing the correct polarity When power is returned the transceiver will light all icons in the LCD and generate all beeper tones once 4 Button Remote Battery Replacement Your remote is powered by a small lightweight 3 volt lithium b
42. t down the remote start operation of the motor or prevent remote start if certain inputs are active The two most important are hood and brake inputs The hood input will prevent the motor from starting as well as shut it down any time the hood is opened The brake O 2004 directed electronics inc pedal will shut down the motor at any time during remote start operation as well as preventing the remote start from activating while it is being pressed nuisance prevention circuitry Your system has Directed s Nuisance Prevention Circuitry NPC It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental conditions such as thunder jackhammers airport noise etc Example If the alarm triggers three times within a 60 minute period and each time the same sensor or switch triggers the alarm NPC will interpret those triggers as false alarms After the third trigger NPC ignores or bypasses that sensor or switch along with any other sensors or switches sharing the same zone for 60 minutes If the bypassed sensor tries to trigger the security system while it is being bypassed the 60 minute bypass period will start over This ensures that a sensor that is continually being triggered will remain bypassed The vehicle doors are protected by NPC differently If your security system is triggered by an open door for three full cycles the system will bypass the doors until th
43. tandard transmission vehicle is dangerous and contrary the product s intended use O 2004 directed electronics inc 9 remote functions The remote buttons are used to send commands to the system The descriptions below reflect the standard configuration for this system The buttons can be custom configured for the user s specific needs by the installer LCD 2 way remote standard configuration 10 LCD 2 way button configuration a Button The System Arm Lock and Multi Level Security Arming func tions are controlled by pressing this button for one second d Button The System Disarm Unlock and High Security Disarm functions are controlled by pressing this button for one second Channel 2 output is controlled by pressing this button for three Button seconds Hold the button down continuously while accessing Channel 2 output Button The panic feature is controlled by pressing this button for two seconds Press again to disable panic mode Button The LCD backlighting will turn on when pressed for less than one second when held for more than five seconds the transceiver will enter adjustment mode allowing the setting of the clock timer 2004 directed electronics inc mode and audible melody selection For more information please refer to the Function Button Configurations section of this guide amp and d Buttons The remote start function of th
44. this system is Directed Electronics Inc Since its inception Directed Electronics has had one purpose to provide consumers with the finest vehicle security and car stereo products and accessories available The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology Directed is ISO 9001 registered Quality Directed Electronics products are sold and serviced throughout North America and around the world Call 800 274 0200 for more information about our products and services Directed Electronics is committed to delivering world class quality products and services that excite and delight our customers driven to excel Vinected ELECTRONICS INC Vista CA 92081 www directed com 9 2004 Directed Electronics Inc All rights reserved G564T 05 04
45. y pressing this button for one second O 2004 directed electronics inc 17 18 d Button The disarming function is controlled by pressing this button for one second AUX Button Silent Mode and an optional auxiliary function are controlled by this button Silent Mode works by pressing this button for less than one second before arming or disarming An optional auxiliary function such as trunk release can be controlled by pressing this button for 1 5 seconds The auxiliary output controls Gk Button The remote start function of your system is controlled by pressing this button twice within 3 seconds and Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously The auxiliary output controls and Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously The auxiliary output controls 2004 directed electronics inc and Buttons The remote start timer mode is controlled by pressing these buttons simultaneously EJ and Buttons The short run turbo mode is activated when these buttons are pressed simultaneously LCD 2 way remote operation The remote start system operates at 434 MHz and incorporates Directed s proprietary A S K out board two way trans
46. you are exiting Valet Mode To enter or exit Valet Mode using the remote 1 Open any vehicle door 2 Press I 3 Press d i Press again The status LED will light solidly if you are entering Valet Mode and it will go out if you are exiting Valet Mode O 2004 directed electronics inc 31 remote start 32 This feature allows you to remotely start and run your vehicle for a programmable period of time This makes it possible to warm up the engine as well as adjust the interior temperature of the vehicle with the climate control system If interior heating or cooling is desired the climate controls must be preset and the fan blower must be set to the desired level prior to remote starting the vehicle important 1 Never remote start your vehicle when the keys are in the ignition except when performing Valet Take Over and 2 Never start the vehicle if it is not in either PARK or NEUTRAL To remote start the vehicle l Press K on the remote twice within 3 seconds 2 The parking lights will flash to confirm that the vehicle will attempt to start 3 A remote start page notification with a unique melody or vibration will be generated and the LCD will display the remote start 19 icon as long as the vehicle is running note The 2 way remote will generate a Page Notification with a different unique two tone beep or vibrate and the remote start 19 icon will turn off when
47. ystem settings The programmer makes it possible to program different settings for each remote that is used with the system Then whenever a specific remote is used the system will recall the settings assigned to that remote Owner Recognition lets up to four users of the system have different settings that meet their specific needs It is almost like having four separate alarms in your vehicle one for each user note Owner Recognition cannot be programmed with out a Bitwriter and the necessary software Check with your dealer for more information rapid resume logic This Directed system will store its current state to non volatile memory If power is lost and then reconnected the system will recall the stored state from memory This means if the unit is in Valet Mode and the battery is disconnected for any reason such as servicing the car when the battery is reconnected the unit will still be in Valet Mode This applies to all states of the system including arm disarm and Valet Mode O 2004 directed electronics inc 45 power saver mode Your system will automatically enter Power Saver Mode while armed or in Valet Mode after a period of time in which no operation has been performed This lowers the current draw on the vehicle s battery Power Saver Mode takes over under the following conditions gt Power Saver when the system is armed After the system has been armed for 24 hours the LED will flash at
Download Pdf Manuals
Related Search