Hoover Bagged Tempo Upright Vacuum Cleaner User's Manual
Contents
1. To avoid personal injury or unnecessary wear to carpet and to prevent the cleaner from falling always place it at the bottom of the stairs Cleaning tools Tools allow for cleaning surfaces above the floor and for reaching hard to clean areas The cleaner is ready for tool use when handle is in upright position CAUTION Agitator continues to rotate while cleaner handle is in upright position Avoid tipping clean er or setting it on furniture fringed area rugs or carpeted stairs during tool use How to clean tools To clean the hose wipe off dirt with a cloth dampened in a mild detergent Rinse with a damp cloth Cleaning tools may be washed in warm water with a detergent Rinse and air dry before using Remove hose When using cleaning tools cleaner handle should be in the upright posi tion Also turn cleaner OFF before disconnecting and connecting hose to hose tube A To use hose lift hose end as shown Lower cover B onto hose tube When you are finished cleaning with the tools be sure to lift cover from hose tube and reposition hose end into tube Select proper tool C Dusting brush may be used for carved furniture table tops books lamps lighting fixtures venetian blinds baseboards shutters and registers D Furniture nozzle may be used for upholstered furniture draperies mat tresses clothing automobile interiors and carpeted stairs E Crevice too2. only genuine HOOVER filter bags made by The Hoover Company to assure that your cleaner operates at peak performance HOOVER bags can be identified by these trademarks Hoover Changing filter bag Disconnect cleaner from electrical outlet Removing bag door To change filter bag push down at top of bag door and pull door forward Remove door Removing and installing filter bag Grasp filter bag collar A and pull collar from tube B Note Do not clean out old filter bag and reuse Discard used filter bag Hold new filter bag as shown Align opening in filter bag with B Push A firmly onto B Tuck in filter bag Replacing bag door Reposition bag door by placing tabs on bottom of door into opening C Press top of door to snap securely shut Secondary and final filters Cleaning secondary filter Disconnect cleaner from electrical outlet The secondary filter A located behind the grill in the bottom of bag compart ment protects the motor from dirt particles If filter becomes dirty pull off grill and lift out filter Hand wash filter in cold water with mild detergent then air dry Reposition dry filter and grill Should you want to replace this filter ask for HOOVER part No 38765019 Cleaning final filter The final filter assists in returning clean air to the room To remove this filter when it becomes dirty remove
3. to become completely red 1 The bag is full change the bag 2 Very fine materials have been picked up clogging the bag pores change the bag 3 There is a blockage in the nozzle hose tools or at the bag opening remove the blockage see Clearing blockages section Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure contin ued cleaning effectiveness Filter bag When to replace Check filter bag from time to time It is recommended that you change the filter bag when dirt reaches the dotted line If more dirt than this accumulates your cleaner will not operate effectively NOTE All new carpet has loose fibers which can fill the bag quickly while vac uuming So if you are using the cleaner on new carpet be sure to change the fil ter bag often CAUTION Very fine materials such as face powder or cornstarch may seal the filter bag and may cause it to burst even though it is partially full of dirt When the cleaner is used to remove material of this nature change filter bag often Where to buy Filter bags may be purchased from your Authorized Hoover Dealer Depot leading retailers Hoover Fac tory Service Centers or through The Hoover Company on line at www hoover com What to buy To assure cleaning effectiveness use only Genuine Hoover Allergen Filtration Type Y disposable filter bags It is imperative that you use
4. F Secure agitator Grasp agitator firmly and fit it into posi tion by first sliding end opposite the belt into the rectangular slot G on side of cleaner Pull other side of agitator H into place Turn agitator making sure belt is not pinched between agitator and agitator shield Replace bottom plate Reposition bottom plate and 4 Phillips head screws Tighten screws securely The agitator brush roll When to replace When agitator brushes are worn the agitator should be replaced To check condition of brushes discon nect cleaner from electrical outlet Move edge of a card across bottom plate while turning agitator To maintain cleaning effectiveness replace agitator if brushes do not touch card What to buy Your cleaner requires either a 13 or 15 agitator When purchasing a new agita tor ask for one of the following 13 HOOVER part No 48414110 15 HOOVER part No 48414115 How to replace Disconnect cleaner from electrical outlet Remove bottom plate belt and agitator following directions in The belt section beginning with Fig 3 10 Discard old agitator Continue following the directions in The belt section to reposition belt new agitator and bottom plate Lubrication The motor is equipped with bearings that contain sufficient lubrication for the life of the motor The addition of lubricant could cause damage Therefore do not add lubricant to moto
5. HOOVER Bagged Tempo Upright Vacuum Cleaner Thank you for your purchase This product was designed for easy assembly See page 3 Review this manual before www hoover com operating cleaner Thank you for choosing a HOOVER product Please enter the COMPLETE model and serial numbers in the spaces provided The numbers are located on the bottom of your cleaner Model Serial number Hint Attach your sales receipt to this owner s manual Verification of date of purchase may be required for warranty service of your HOOVER product Be sure to fill out and return the product registration card included with your cleaner Contents Assembling Cleaner csessneee 3 4 HOW tO USEC ccecsseeeecesseeeenseeeeneneeenseeeeenee 5 Cleaner Description sscsseeee 5 Cleaning TOols cccecsseseeeeseeee 7 8 If You Have a Problem sssesseeen 12 Clearing Blockages seseeesee 12 Important Safeguards cscceeeeeeees 2 Maintenance Authorized Service ccssceeeeeee 11 Cleaning Filters scsssseeeseeeees 9 LUDrIiCAtION sscccccsceccccsciisctscscedtcrssaneses 11 Replacing Agitator Brush Roll 11 Replacing Belt csssessseseees 10 11 Replacing Headlight ccsseeees 10 Replacing Filter Bag s cssse 8 9 Thermal Protector cccsseeesssesseees 11 Warranty aiccesccesassssecnssscensaesssnesssnaiisanan 12 2003 The Hoover Company w
6. bag door and pull down top of filter Removing and replacing filter Lift out filter B and hand wash it in cold water with mild detergent Let filter air dry and reposition it on the side of cleaner Reposition bag door Should you want to replace this filter ask for HOOVER part No 40110004 Do not operate cleaner without either the secondary or final filter in place Check agitator shield Because your cleaner picks up so well we strongly recommend you check for debris accumulation under the agitator shield each time you clean the filters Removing debris under the shield will help maintain your cleaner s excellent pick up and suction Remove debris as follows 1 Disconnect cleaner from electrical outlet 2 Check for dirt accumulation by remov ing bottom plate Fig 3 10 removing agitator Fig 3 11 and lifting agitator shield Fig 3 13 3 Remove any debris and replace shield agitator and bottom plate Figs 3 13 to 3 15 Continued 2 9 Headlight replacement What to buy This cleaner uses a 12 volt wedge base type 912 bulb HOOVER part No 27313101 Remove lens Disconnect clean er from electrical outlet Using a screwdriver remove the two screws as shown and lift off lens Install bulb Pull old bulb straight out of socket Push new bulb straight into socket until locked in place Excessive force is not required Replace lens Reposition lens and secure with
7. ctor Problem Cleaner tools won t pick up Possible cause Possible solution Broken or worn belt e Replace belt Agitator brush roll worn Replace brush roll Filter bag full e Change filter bag Incorrect carpet height setting e Move nozzle control knob to lower setting e Blockage in air flow passage e Clear blockage Problem Cleaner hard to push Possible cause Possible solution Incorrect carpet height setting Move nozzle control knob to a higher setting Problem Smoky burning smell detected Possible cause Possible solution Belt broken or stretched Replace agitator brush roll belt as described in Figs 3 17 through 3 27 in the Maintenance section Clearing blockages Disconnect cleaner from electrical outlet Low suction or pick up may be due to a blockage in the system Refer to the fol lowing steps to check for blockages continuing with each step until the blockage is found Turn cleaner OFF and disconnect from electrical outlet 1 Check fullness of filter bag change if needed Check airflow path 2 Plug cleaner in and turn ON Check for suction at end of hose A a If there is suction continue with step 3 b If there is no suction check for blockage in hose and dirt tube as follows 1 Disconnect hose from dirt duct C by reversing procedure for Attach hose Fig 1 8 and 1 9 2 Clear out hose 3 Look into C and remove block age 3 C
8. ets in the U S A phone 1 800 944 9200 OR visit The Hoover Company on line at www hoover com This warranty does not cover pick up delivery or house calls however if you mail your appliance to a Hoover Factory Service Center for warranty service transportation will be paid one way While this warranty gives you specific legal rights you may also have other rights which vary from state to state or province lf further assistance is needed or if there are questions concerning this warranty or the availability of warranty service outlets write or phone the Consumer Response Center The Hoover Company 101 East Maple St North Canton Ohio 44720 Phone 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 Phone 1 800 263 6376
9. g or filters in place Empty bag frequently when picking up very fine materials such as powder e Use extra care when cleaning on stairs Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair or anything that may reduce air flow Do not pull or carry by cord use cord as a handle close door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated surfaces Always disconnect cord from electrical outlet before servicing the cleaner Unplug cleaner when not in use Turn off all controls before unplugging Do not unplug by pulling on cord To unplug grasp the plug not the cord Never handle plug or appliance with wet hands The use of an extension cord is not recommended Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water take it to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot e Use vacuum cleaner only for its intended use as described in the instructions Use only attachments recommended by The Hoover Company others may cause hazards Save these instructions If you need any assistance Visit our website at www hoover com Click on the Service button to find the service outlet nearest you OR Call 1 800 944 9200 for an automated referral of service outlet locations U S onl
10. heck connection at hose tube B remove any blockage Checking under bottom plate 4 Turn cleaner OFF and unplug 5 Remove bottom plate belt and agita tor see The belt section Look into opening D for blockages and remove 6 Remove agitator shield see Fig 3 13 and remove any loose debris which may have accumulated under it Full One Year Lich Domestic Use Your HOOVER appliance is warranted in normal household use in accordance with the Owner s Manual against original defects in material and workmanship for a period of one full year from date of purchase This warranty provides at no cost to you all labor and parts to place this appliance in correct operating condition during the warranted period This warranty applies when the appliance is purchased in the United States including its territories and possessions or in Canada or from a U S Military Exchange Appliances purchased elsewhere are covered by a limited one year warranty which covers the cost of parts only This warranty does not apply if the appliance is used in a commercial or rental application Warranty service can only be obtained by presenting the appliance to one of the following Authorized Warranty Service outlets Proof of purchase will be required before service is rendered 1 Hoover Factory Service Centers 2 Hoover Authorized Warranty Service Dealers Depots For an automated referral of authorized service outl
11. ice tool Handle release lever step on lever to lower handle to operating or low positions Dusting brush Final filter exhaust Furniture nozzle Hose hook Crevice wand stores inside of extension wand 15 16 17 18 19 Available on some models Operate cleaner only at voltage specified on data plate on bottom of cleaner This cleaner is intended for household use Cord clip To help keep the cord out of the way while vacuuming position cord down into cord clip B located between top cord hook and handle Continued 2 5 2 5 ald Se Handle positions Transporting cleaner Carrying handle The handle of your cleaner has three Put handle in upright position Tilt Use the carrying handle to lift the positions upright for storage and when cleaner back on rear wheels Push cleaner using cleaning tools operating posi forward tion for general operation on carpet and floors low for reaching under low furniture Step on handle release lever to lower handle A BARE FLOOR Carpet height Handle position Settings adjustment For ease in sliding knob place handle For maximum cleaning performance The cleaning of carpet and rugs takes in the upright position C the following carpet height settings are place at the nozzle A The nozzle will not move into the recommended When it is necessary to raise and lower the adjusted position until the cleaner e Lowe
12. l may be used in tight spaces corners and along edges in such places as dresser drawers uphol stered furniture stairs and baseboards F Extension wands are used to give extra length to your hose Use it with any of the above tools G Crevice wand included on some models may be used for the same tasks as the crevice tool is used It can also be used for extra reach with the dusting brush and or extension wand Continued gt 7 Attach wand and tools Attach tool or wand or crevice wand some models to the hose H by pushing it firmly into hose Attach second wand or tool to the wand in the same manner Twist wand or tool slightly to tighten or loosen the connection Extra reach hose available at additional cost The extra reach hose provides you with a 20 foot reach to allow easier cleaning of stairs and hard to reach places Follow the steps below for attaching and detaching hose Push ON OFF switch to OFF position and unplug from electrical outlet Remove regular hose from cleaner Align end of extra reach hose with projec tions I over slots J in dirt duct Slide hose into slots J and twist hose to lock it into place To detach hose reverse procedure Attach wands or tools to the other end of hose Check bag indicator The indicator K will begin to show red as the filter bag fills with dirt There are three conditions that will cause the indicator
13. over Company in North Canton for service this will only result in delay If further assistance is needed contact The Hoover Company Consumer Response Center North Canton Ohio 44720 Phone 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 Phone 1 800 263 6376 Always identify your cleaner by the complete model number when requesting information or ordering parts The model number appears on the bottom of the cleaner Hoover cleaning performance This Hoover Cleaning Performance Sys tem is for comparing the relative pro gressive performance of Hoover uprights only and not for comparison with any other brands The majority of this rating is based upon the ASTM International Carpet Cleaning Effective ness Test ASTM Test F608 Other per formance factors include Hose Power ASTM Test F558 Surface Litter Clean ing Hard Floor Cleaning Edge Clean ing Cleaning Width and Air Filtration Continued gt 11 you have a problem If a minor problem occurs it usually can be solved quite easily when the cause is found by using the check list below Problem Cleaner won t run Possible cause Possible solution e Not firmly plugged in e Plug unit in firmly No voltage in wall plug e Check fuse or breaker Blown fuse or tripped breaker e Replace fuse or reset breaker Thermal protector activated e Allow cleaner to cool for 30 minutes this will reset the thermal prote
14. r bearings The agitator brush roll is equipped with two ball bearings that should be lubri cated periodically by a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer Depot Thermal protector An internal thermal protector has been designed into your cleaner to protect it from overheating When the thermal protector activates the cleaner will stop running If this happens proceed as follows 1 Turn the cleaner OFF and discon nect it from the electrical outlet 2 Check secondary and final filters for dirt accumulation 3 Refer to Clearing blockages section 4 When cleaner is unplugged and the motor cools for 30 minutes the thermal protector automatically resets and cleaning may continue If the thermal protector continues to activate after following the above steps your cleaner may need servicing see Service section Service To obtain approved HOOVER service and genuine HOOVER parts locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot by e checking the Yellow Pages under Vacuum Cleaners Household OR e checking the list of Factory Service Centers provided with this cleaner OR e checking the Service section of The Hoover Company on line at www hoover com OR e calling 1 800 944 9200 for an automated referral of authorized service outlet locations U S only Do not send your cleaner to The Ho
15. se tube E Position tools Place smaller unridged end of wand into bottom of rack Snap wand into clip Repeat with other wand Snap ends of dusting brush A crevice tool B and furniture nozzle C into clips as shown Place crevice wand D available on some models inside extension wand E Cleaner description Polarized plug To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not change the plug in any way ON OFF swi NO of 10 11 12 tch Plug cord into electrica To turn cleaner ON push switch A toward front of cleaner To turn cleaner OFF push toward back of cleaner outlet Handle Hose ON OFF switch located on left rear corner of cleaner body Carrying handle Bag door Check bag indicator Stair cleaning handle located on lower edge of dirt cup Headlight Furniture guard helps prevent cleaner from marking furniture Nozzle control knob slide knob to correct set ting for height of carpet being cleaned Wands Cord hooks wrap cord around hooks for storage The top hook rotates right or left for easy cord release 13 14 Crev
16. st setting for all types of carpet nozzle for various carpet pile heights slide handle is lowered to the operating and hard floors pees control knob B to the desired position D Note If the cleaner is difficult to push slide knob to the next higher setting Higher settings for very deep pile carpet where easier pushing effort is desired while maintaining good cleaning performance Cleaning lightweight flexible rugs Stand on one end of rug and move cleaner toward other end or edge Before reaching edge push down on handle This will lift up the nozzle front of cleaner as shown and will prevent rug from clinging to cleaner Continue to lift up nozzle so that when you have reached the edge it is completely off the rug Move cleaner back to start again lower nozzle and use only for ward strokes Edge cleaning Edge cleaning is provided on both sides of the nozzle to remove dirt in carpet near baseboards and furniture Guide either side of nozzle parallel to edge of carpet or furniture Stair cleaning A stair cleaning handle has been designed for ease in using your cleaner on stairs With handle in operating posi tion place fingers under edge of stair cleaning handle and guide cleaner with other hand on upper handle As an alternative you may use the hose and furniture nozzle for stair cleaning Clean from bottom to top When using cleaning tools the agita tor will continue to rotate CAUTION
17. the two screws Belt replacement The belt on your Hoover cleaner causes the agitator to rotate and is important for the effective operation of the cleaner The belt is located under the bottom plate of the cleaner and should be checked from time to time to be sure it is in good condition When to replace Disconnect cleaner from electrical outlet To check belt remove bottom plate as shown in How to replace Replace belt if it is stretched cut or broken What to buy To assure effective operation use only genuine HOOVER belts with your cleaner When purchasing a new belt ask for HOOVER part No 38528033 belt package part number 40201160 How to replace Disconnect cleaner from electrical outlet Remove bottom plate Place handle in low position and turn cleaner over so bottom side is up Remove the 4 screws as shown with a Phillips screwdriver Lift off bottom plate A Remove agitator brush roll Remove agitator and used belt Discard used belt Install new belt With lettering on outside of belt and positioned as shown in box on B slide new belt over motor pulley C 10 Replace agitator brush roll Insert agitator through belt and place belt in belt guide D on agitator Should the agitator shield E become dislodged while replacing the belt or the agitator reposition it as shown noting the placement of its belt guide
18. ww hoover com mez AN XXXXXX MODELO CLEANER ASPIRATEUR ASPIRADORA fe SERIES SERIE SERIE step BAG TYPE SAC TYPE BOLSA TIPO FILTER FILTRO FILTRE THE HOOVER CO CARTRIDGE PART NO HOUSEHOLD TYPE TYPE MENAGERIPO DOMESTICO SERIAL NO NUMERO SER NUMERO DE SERIE mann THE HOOVER C0 A N a XXXXXXXXXXXX SERIAL NUMBER Important Safeguards When using an electrical appliance always follow basic precautions including the following READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE m E Wa rn l n m To reduce the risk of fire electric shock or injury Do not use outdoors or on wet surfaces e Close supervision is necessary when any appliance is used by or near children Do not allow vacuum cleaner to be used as a toy or to run unattended at any time Keep hair loose clothing fingers feet and all parts of body away from openings rotating agitator and other moving parts Do not operate cleaner in bare feet or when wearing open toe shoes or sandals Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use to pick up flammable or combustible materials such as gasoline or fine wood sandings or use in areas where they may be present Avoid picking up hard sharp objects with the cleaner They may damage the cleaner and the bag Always turn off this appliance before connecting or disconnecting hose Do not use without dust ba
19. y OR Call 1 330 499 9499 to speak with a representative in our Consumer Response Center Please do not return this product to the store 1 Cleaner Assembly Carton contents Empty carton Find the parts shown before disposing of packing materials A Handle section B Cleaner body C Hose cleaning tools and wands D Crevice wand included with some models E Handle bolts and nuts packet in bag with owner s manual Remove bag door on cleaner body by Slide handle onto cleaner body Push bolts into holes on back of handle pushing down at top of door and pulling door outward Switch A above bag door should be in OFF position Continued gt 3 Place nuts in recessed areas on front of handle Hold each nut in place while tightening each bolt securely with a Phillips screw driver Reposition bag door by fitting tabs on bottom of door into opening Press top of door to snap securely shut Position cord on back of cleaner as shown and press cord into clip Attach hose Align end of hose with projections A over slots B in dirt duct Note all operations Slide hose into duct B and twist hose to lock it into place Hose must be connected as shown for Lift hose tube cover C Position hose over hose hook D and into ho
Download Pdf Manuals
Related Search