Honeywell PRO22ENC1 User's Manual
Contents
1. Fire Safety and Liability Notice Never connect card readers to any critical entry exit door barrier elevator or gate without providing an alternative exit in accordance with all fire and life safety codes pertinent to the installation These fire and safety codes vary from city to city and you must get approval from local fire officials whenever using an electronic product to control a door or other barrier Use of egress buttons for example may be illegal in some cities In most applications single action exit without prior knowledge of what to do is a life safety requirement Always make certain that any required approvals are obtained in writing DO NOT ACCEPT VERBAL APPROVALS THEY ARE NOT VALID Engineered Systems never recommends using the PRO 2200 or related products as a primary warning or monitoring system Primary warning or monitoring systems should always meet local fire and safety code requirements The installer must also test the system on a regular basis by instructing the end user in appropriate daily testing proce dures Failure to test a system regularly could make installer liable for damages to the end user if a problem occurs EARTH ground all enclosures for proper installation EARTH ground can be obtained through the power supply or by grounding the cabinet BUT NOT BOTH Use suppressors on all door strikes Use S 4 suppressors for installation Engineered Systems recommends only DC strikes The information in2. Two required 500 Mhz 128Mb RAM 9 1Gb hard drive CD ROM 10 100 TX network card 17 SVGA Monitor Peripheral Hardware Requirements UL approved network HUB with at least 4 ports UL approved CAT 5 network cable and connectors PRO221C Controller and accompanying I O boards Cobox network card PRO221C mounted Operating System Requirements NT Server 4 0 or better NT Service Pack 5 or higher Software Packages Required SQL Server 7 0 SQL Server Service Pack 1 or higher WIN PAK PRO 3 0 with SQL database selection Receiving Unit minimum configuration e PRO22bNC1 or PRO22ENC2 cabinet PRO22ULPS ALTRONIX AL400 ULX power supply with 40 AH battery back up PRO221C controller panel PRO22IN input panel PRO22EN Cobox Ethernet card PRO22ENSP Tripp Lite DNET1 Ethernet surge protector The following priority of incoming signals must be used for UL1076 1 Fire alarm N A WIN PAK PRO is not certified for fire alarm supervision 2 Hold up Panic alarm 3 Burglar alarm PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Installation Guide 13 4 Watchman tour 5 Fire alarm supervision N A WIN PAK PRO is not certified for fire alarm supervision 6 Burglar alarm supervision 7 Industrial supervision 8 Other supervisory services NOTE 2 and 3 may have equal priority 5 and 6 may have equal priority amp 7 and 8 may have equal priority Other UL1075 Notes Procedures A
3. connection with the acts or omissions of Customer and its agents and employees and from and against all claims demands losses and liability for costs of fees including reasonable attorneys fees in connection therewith Unpacking Procedure CAUTION If any damage to the shipment is noticed before unpacking a claim must be filed with the commercial carrier All containers should be opened and unpacked carefully in order to prevent damage to the contents The following steps are used to unpack equipment in preparation for installation 1 Open the container and remove the unit s and all packing material Retain the container and all packing materials They may be used again for reshipment of the equipment if needed 2 Inspect the contents for shortage If items are missing contact the order entry department at 800 323 4576 3 Visually check contents If damage is discovered perform the following If shipping caused damage to the unit a claim must be filed with the commercial carrier If any other defect is apparent call 800 323 4576 for a return authorization PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Installation Guide 7 Shipping Instructions To ship equipment back to Engineered Systems 1 Contactthe customer service department before returning equipment at 800 323 4576 Please have the following available when calling A description of the problem or reason for returning the equipment Original purchase
4. order number invoice number and if the unit is under warranty Anew purchase order number if the unit is not under warranty 2 Obtain the Return Authorization Number RMA from the customer service department at 800 323 4576 3 Show the RMA number on all packages shipped Packages which are not marked with an RMA number will be refused at the factory and returned COD 4 Carefully pack the equipment for shipment Use the original packing material whenever possible Limited Warranty All Products sold or licensed by Engineered Systems include a warranty registration card which must be completed and returned to Engineered Systems by or on behalf of the end user in order for Engineered Systems to provide warranty service repair credit or ex change All warranty work shall be handled through Customer which shall notify Engi neered Systems and apply for a Return Merchandise Authorization RMA number prior to returning any Product for service repair credit or exchange Engineered Systems warrants that its Products shall be free from defects in materials and workmanship for a period of two years from date of shipment of the Product to Customer The warranty on Terminals Printers Communications Products and Upgrade kits is 90 days from date of shipment Satisfaction of this warranty shall be limited to repair or replacement of Prod ucts which are defective or defective under normal use Engineered Systems warranty shall not extend to any
5. 7 6 NOIBS aueh ort tona HO pag sussa VA pao A 13 Procedures v gdes ER cx KR AN BANAN KRA a Kr 13 Second PC Installation sa anelli ea ea 14 Enterprise Manager Sell 1st onm e atenta kar KKR KKR KKR alae 14 Pre Redundancy Verification anna ila pe exo PODER 15 DITS Package VerlticallOTiusiecsdnaserexve tetro ree et e Pod dte ae nate fedora 15 Interim Steps Before Full Redundancy Verification rna 15 Redundant Test Examples unsssersrrrrsrrssrrrrrrrrrrrerrrrrrrrrrrrr aree K N e Dat e ttd RR rren 16 Bii EE 16 Cond it KNOCKOUTS contia iene Pu Rama dea 17 Power Supply ENCIOSUMG ou usse ili ei 17 Installa ion Diagrammi oet not mi leale 17 DIMENSIONS sarei 17 Installation INStCUCONS eruditi 18 Cable Sp ECIfl CAO ns E 19 ESG Cable Part NUMbeTrS sysnssessrrersrrersrrerererrrrrrrrrerrrrrr arne kr rr RK ETTEN KKR RR KKR RK KKR KKR RK KKR 20 INO TES Gallella alia 21 Installation Guide PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Warnings and Cautions WARNING WARNING WARNING WARNING Before installation TURN OFF the external circuit breaker which supplies power to the system Before connecting the device to the power supply verify that the output voltage is within specifications of the power supply Do not apply power to the system until after the installation has been completed Personal injury or death could occur and the equipment could be damaged beyond repair if this precaution is not observed
6. E AND PANELS Wire the TCP IP connection to the network HUB PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Installation Guide 19 Cable Specifications Application ESG PartNo AWG Description Max Dist Imp Cap N 485 connections NC2442 TN N A Belden 9842 4000 1200m 1200 12 8pf ft N A or equivalent CR 1 TR 1 CI 1 KR 1 NC1861 BL 18 6 conductor shielded 500 152 m Wiegand card readers NR 1 magstripe reader NC1861 BL 18 6 conductor shielded 500 152 m PR 1 280 Cotag reader 280 read head to SZC NC1861 BL 18 6 conductor shielded 300 91 m SZC to N 1000 1I NC1861 BL 18 6 conductor shielded 500 152 m PR 2 Hughes reader scanner to reader NC1861 BL 18 6 conductor shielded 30 9 m reader to N 1000 Il NC1861 BL 18 6 conductor shielded 500 152 m PR 3 PR 5 Indala readers A 3 A 5 read head to RE 2 NC18121 YL 18 12 conductor shielded 75 23 m RE 2 to N 1000 I NC1861 BL 18 6 conductor shielded 500 152 m PR 20 PR 22 Indala readers A 20 A 22 read head to RE 2 NC18121 YL 18 12 conductor shielded 75 23 m RE 2 to N 1000 II NC1861 BL 18 6 conductor shielded 500 152 m PR 10 PR 12 Indala readers NC1861 BL 18 6 conductor shielded 500 152 m HG 3 hand geometry reader NC1861 BL 18 6 conductor shielded 500 152 m 5 conductor keypad NC1861 BL 18 6 conductor shielded 500 152 m Alarm input points NC 2221 BR 22 2000 610 m Relay outputs NC 1821 OR 18 twisted pair shielded 2000 610 m NOTE For Plen
7. H MES 225 3 68 4 56 T toic gt 9 34cm gt lt 11 6cm Q3 9 6 i 45 11 4cm 15 5 gt 39 4cm gt 3 25 8 25cm SM IR 5 58cm as VENA 3 16em a 2 54em i 122 3 1cm 1 22 i 3 1cm S y ALTRONIX AL400 ULX PRO22ULPS bet 2 25 Je a 3 68 die 456 i 5 71cm 9 34cm 11 6cm 18 Installation Installation Guide PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Installation Instructions 1 10 4 12 13 14 Install the PRO22ULPS Altronix AL400ULX power supply and battery enclosure per the supplied instructions Measure and install four mounting screws with heads smaller than 4 1cm using proper techniques for the material on which the PRO22ENC1 or PRO22ENC2 is being mounted Use a rectangular screw pattern 12 1 H x 16 W 0 307m H x 0 4064m W Leave the screws exposed approximately 1 2 1 27cm Open the door of the enclosure and place the hanging slots over the mounting screws Push the enclosure over the mounting screws and allow the screws to slide into the slots Finish tightening the mounting screws to securely hold the enclosure Run all appropriate wiring to the case All cable shields should tie to the grounding lug found on the top of the enclosure Install the required panels into the runners The PRO22IC sho
8. PRO 2200 Enclosure Installation Manual Part Number PRO22ENC1 PRO22ENC2 Honeywell TD1138 rev0801 PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Installation Guide 3 Contents Warnings and Cautions useerererrrrerrrrrrrrrerrrerrrrrrrr eit eng vars OE NUN KKK KRK crar etn x 4 DisclalME PEOR DU I EE 6 Product Liability Mutual IndemnificaliOfi eiie eric eerte erba rte e 6 UNPACKING PEOCeQUEG s cce tena t a ape te ER HE ISI vasa liset REPRE pe och NUN Tabu 6 CAUTION peccati 6 Shipping Imnmasthtctofis lei rob Ue x aioe Ut cone ene KaMe olma ey ke nane bred 7 Umited Warranty cosca 7 Confidentiality ionii a krk HAR A E NAE A a 8 PRO 2200 ER CIOSURG slittino caga 9 DGSCHDUOM a2 mE 9 DIMENSIONS rela 10 Condiltknocko sanare eil 10 Power SUD DIY nua aan sae ho er eir re Lese e Re rne ety evo tao 10 Maintenance uil epe bk e eed edet det bia e prend Lcx Ned 10 Installation INSCUCtONS anu vassa tas eo a myi eb Roter ottenere eei aec in aer RR ARR ka nag 10 Installation Diagrammi tolo 11 ULL OG SEN De reta Hanna ra de bd aa RNE aaa 12 PC Minimum ReQUire MENS issssssesrssrsssrrrrrrrrrrerrerererr rar rr arr edi rr pn ERO Ren RR RR RAR RR KRt 12 Peripheral Hardware Requirement isis nere reri c ote teen ert 12 O perating System Requirements snelle e HORN 12 Software Packages Required srt 12 Receiving Unit minimum configuration a ci roue ti ota ri 12 Priority of incoming signals for U E10 76 ences fete totae beet eo er tus 12 O ther ULLO
9. Product which upon examination is determined to be defective as a result of misuse improper storage incorrect installation operation or maintenance alteration modification accident or unusual deterioration of the Product due to physical environments in excess of the limits set forth in Product manuals THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THIS PROVISION THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS IMPLIED OR STATUTORY INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE NO REPRESENTATION OR WARRANTY OF THE DISTRIBU TOR SHALL EXTEND THE LIABILITY OR RESPONSIBILITY OF THE MANUFACTURER BEYOND THE TERMS OF THIS PROVISION IN NO EVENT SHALL ENGINEERED SYSTEMS BE LIABLE FOR ANY RE PROCUREMENT COSTS LOSS OF PROFITS LOSS OF USE INCIDENTAL CONSEQUENTIAL OR SPECIAL DAMAGES TO ANY PERSON RESULTING FROM THE USE OF ENGINEERED SYSTEMS PRODUCTS 8 Installation Guide PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Confidentiality All software drawings diagrams specifications catalogs literature manuals and other materials furnished by Engineered Systems relating to the design use and service of Products shall remain confidential and shall constitute proprietary rights of Engineered Systems and Customer agrees to treat such information as confidential Customer shall acquire no rights in the design of Products or the related materials except to use such information solely for the purpo
10. e WIN PAK PRO database using the provided script for attachment Open up the ODBC application in the Control Panel and create a link to the WIN PAK PRO SQL database The name used for a description should match the WIN PAK PRO System Manger DSN Tab name Default is WIN PAK Database See the WINPAK PRO installation manual for complete procedure The database server can now be started Launch the User Interface and connect using ADMIN as the name without a password 10 The database should now be programmed to accommodate the PRO22IC panel and accompanying I O boards Refer to the WINPAK PRO Installation Manual for additional detail The programming should continue until the system is fully functional and communications have been established Below are the programming requirements for setting up the PRO22IC panel A Direct to Port selection required when adding a new PRO22IC B A unique TCP IP address is required for assignment to the panel and should match the IP address you programmed through the Cobox software C Program all the ADV s for the hardware so that you will be able to monitor the points and system alarms D Once the program is configured shut down the User Interface and restart all the services Launch the User Interface and verify communications E Program the Communications Server with Local Machine for the Node Name F Program a Control Map and or Floorplans with the hardware Example Panels SIO boards Inp
11. he nine modules can be an intelligent controller PRO221C The remain ing eight slots can be used and configured in a variety of combinations of readers supervised inputs relay outputs and other specialized modules to customize the system for the individual site The PRO22ENC1 PRO22ENC2 can be configured in any combination of the PRO22IC PRO22IN PRO220UT PRO22R2 and PRO22R1 An optional daisy chain cable PRO22DCO provides an RS 485 communication and power bus between the nine modules 10 Installation Guide PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Dimensions ENC1 ENC2 Height 13 9 0 353 m 13 9 0 353 m Width 17 0 4318m 18 9 0 48006 m Depth 9 0 2286 m 9 0 2286 m Metal thickness 05 1 27 mm Color Autumn White Installation holes Four hangers in a rectangular pattern 12 1 0 30734 m Hx16 0 40640 m W Conduit Knockouts V2 0 0127 m 2 0 05080 m Back 9 2 Top 9 2 Right Side 2 1 Left Side 2 1 Power Supply Use PRO22E1PS or other approved power supply See Installation Manual for details Maintenance Oil lock once per year If battery backup is used change battery every 2 to 2 1 2 years Installation Instructions 1 Measure and install four mounting screws with heads smaller than 4 0 01016 m using proper techniques for the material on which the PRO 2200 is being mounted Use a rectangular screw pattern 12 1 0 30734 m H x 16 0 40640 m W Leave the screws exposed approx
12. imately 1 2 0 0127 m 2 Openthe door of the enclosure and place the hanging slots over the mounting screws Push the enclosure over the mounting screws and allow the screws to slide into the slots Finish tightening the mounting screws to securely hold the enclosure 3 Runall appropriate wiring to the case Mark each wire as to the panel location and input type All cable shields should tie to the copper grounding lug found on the bottom right of the enclosure 4 Install the required panels into the metal runners The PRO22E1PS should be placed in the right most location and installed according to its own instruction manual The PRO22IC should be installed next to it as the right most panel 5 Wire the readers input and output connections see wiring guide at end of manual 6 CHECK ALL CONNECTIONS PRIOR TO POWERING UP THE ENCLOSURE AND PANELS PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Installation Guide 11 7 Theremainder of the panels can be manually wired for power and RS 485 communications using 18 AWG wire The wires will be daisy chained from one panel to the next so the power and the communications are wired in parallel PRO22DCC is available as an option to be purchased with the equipment This will reduce wiring time in the field since the power and RS 485 communications between panels is factory wired in a harness that plugs into the bottom two connectors on each panel The only field wiring required is the two wiring co
13. ll alarms and troubles must be acknowledged by attending guard Reports of all alarms and troubles must be printed and stored at least once per week When communications are disrupted from the protected area unitto the Central Supervisory station all panels must be buffered They must transmit all stored alarms and troubles to the Central Supervisory Station when communications are restored If Cameras are used they must be UL approved Camera operation was not verified by UL Guard Tour was not verified by UL to NFPA 72 standards Exit and Entry Delay can not exceed 60 seconds Polling of a receiving unit may not exceed 200 seconds Configure the PC s by installing the NT Server 4 0 A PC names should be unique and described with Alpha characters B IP addresses should be unique and have the same Subnet Mask C Each PC should be of the same workgroup name Install NT Service Pack 5 or higher Install SQL Server 7 0 Select either NT Authentication or Local System but be consistent with both PC installations Install SQL Server 7 0 Service Pack 1 Setup the Cobox PRO22EN per it s installation manual Install the WIN PAK PRO Software on the MAIN PC A Select Full Installation B Select SQL for Database C Install the Desktop Icons D Upon reboot of the PC stop all the WIN PAK PRO Services 14 Installation Guide PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 7 Use the Query Analyzer to connect to th
14. ll not be duplicated used or disclosed to others for procurement or manufacture except as authorized by and with the written permission of Engineered Systems Inc The information contained in this document or in the product itself is considered the exclusive property and trade secrets of Engineered Systems Copyright laws of the United States protect all information in this document or in the software product itself Any use of this product is subject to the terms and acceptance of the Engineered Systems Software Agreement Please request a copy from Engineered Systems and review the agreement carefully Installation Guide PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Disclaimer Product Liability Mutual Indemnification In the event that a Customer receives a claim that a Product or any component thereof has caused personal injury or damage to property of others Customer shall immediately notify Engineered Systems in writing of all such claims Engineered Systems shall defend or settle such claims and shall indemnify and hold Customer harmless for any costs or damages including reasonable attorneys fees which Customer may be required to pay as a result of the defective Product or the negligence of Engineered Systems its agents or its employees Customer shall hold harmless and indemnify Engineered Systems from and against all claims demands losses and liability arising out of damage to property or injury to persons occasioned by or in
15. nnections of the red and black 12 VDC cables connecting the PRO22DCC and the PRO22E1PS power supply Installation Diagram CN tj NY PRO22ENC1 0229 L HOLE PATTERN 1001 MATCHES TOP AND 0025 1 00 Le 8 00 8 00 BACK CEN 1 00 at I 0 203 i 0 203 I 0 025 TOA ju 4 LIT os TO MEE ig 0 Q5 OO d tI i IT N J V m 000000 2 00 0 051 PI TT 500 00 i si T x gt 12 1 S 0 307 os Pl dad c x 9 05 S 0 230 3 gt a Ali A NE e lic 16 0 0 406 17 0 0 432 18 9 0 480 FH al aa NES dat N IN er oe 4 J 2000 N 9 00 0 196 175 H 0 229 d 13179 009 PRO22ENC2 0 035 13 00 0 330 HOLE PATTERN 1100 MATCHES TOP AND 0 025 7 99 Le ko 300 s 8 00 sl BACK CEN 1 9 al I 0 203 0 203 I 0 025 T T oF ES NS 333950 VO 1 65 0 042 00000 J HH NA 000 0 e 299999 Nu 2000 051 na Q 1 12 1 0 307 0 353 BD x 9 05 0 230 jal Fa i st sot ecc 16 0 0 406 17 0 0 432 12 Installation Guide PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 UL1076 Setup PC Minimum Requirements
16. package which will be run when the user wants to keep the database current with the MAIN PC 10 Click Next Change the name or accept the default for the local package being created Leave the Server name as LOCAL Select either NT Authentication or SQL Server Authentication whichever matches your requirements 1 Click Next Select finish and DO NOT ABORT THIS PROCESS This DTS process will import all the data from the MAIN PC to the Redundant PC When the transfer is successful click OK 12 If a Publication Wizard opens select Cancel Use the SQL Server Manual to utilize this feature later however it is not required for this setup Click Done and minimize Enterprise Manager Pre Redundancy Verification 1 Stop all the services on the MAIN PC 2 Start services on the Redundant PC and launch the User Interface Log in as ADMIN 3 Verify that the data is consistent with the MAIN PC 4 Verify communication with the hardware by using the Alarm View Control Map or Floorplans 5 Next close the user interface and stop the services on the Redundant PC DTS Package Verification 1 Maximize Enterprise Manager and locate the Data Transformation Services Folder Expand the folder and the click on Local Packages 2 Find the Local Package that was created earlier Double click on the package to open up the DTS menu Select Package on the menu bar and then Execute 3 The DTS package will run until it is done transferring
17. rmal stop the stop watch This time represents the amount of time that has passed since the MAIN PC went off line Power Supply Dimensions Height 15 5 39 4cm Width 12 30 5cm Depth 4 5 11 43cm Color Grey Installation holes Four hangers in a rectangular pattern 13 5 H x 9 825 W 34 3cm H x 25cm W PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Conduit Knockouts Top Bottom Right Side Left Side Power Supply Enclosure Installatio Dimensions n Diagram 3l Installation Guide from Enclosure to Door N CAUTION De energize unit prior to servicing Switch Position For continued protection against fire hazard replace 24VDC SW1 OPEN fuse with the same type and rating 3 5A 250V 12VDC SW1 CLOSED O AL400ULXB TA N TN DC Output _ to devices ui cll power nite PL gt 7 gt Fuse n ELLE N B Battery and AC Strain Ii 115 power Supervision Circuit Relief e mains non power limited Wire Strap Green Lead To Battery Enclosure with 40AH Battery Battery connection non power limited AL400ULX Assembly diagram for use with the PRO22ENC1 and PRO22ENC2 for UL1076 1 22 875 13 ii donem im i lt gt la lt gt gt E 12 i n R r x d N um mE x dem P gt
18. se of and only during the time it sells Products Customer shall not copy the design of any Products or use or cause to be used any Product design or related materials for its own benefit or for the benefit of any other party The covenants contained in this section shall remain effective throughout the term of this Agreement and thereafter unless specifically waived by Engineered Systems in writing PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Installation Guide 9 PRO 2200 Enclosure TOP 0000 TO g E r3 rpg 2 E C d aa PRO22ENCI PRO22ENCc2 NUMBER PART NUMBER EACH DESCRIPTION 1 PRO22E1LK 1 LOCK WITH RETAINING TANG AND KEY a PRO22E1DR 1 REMOVABLE DOOR 3 PRO22E1WN 4 8 32 WINGNUT 4 PRO22E10C l 25 MALE QUICK CONNECT 5 PRO22EIGW 1 DOOR GROUNDING CABLE 6 PRD22ELWR 3 7 8 WASHER Y PROS2EITH 1 TAMPER SWITCH HOLDER 8 PRO22E1Sw 1 TAMPER SWITCH 9 PROPPENTS 1 TAMPER SWITCH CABLE 10 PRO22E2FL 2 MOUNTING FLANGE FOR 197 RACK AVAILABLE ON PRO22ENC2 ONLY The PRO 2200 system is designed for maximum efficient use of wall space through the use of a secure metal cabinet PRO22ENC1 PRO22ENC2 that can hold up to nine modules a 4 amp power supply PRO22E1PS and a self contained replaceable backup battery Typically one of t
19. stallation Guide NOTES 21 22 Installation Guide NOTES PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Installation Guide 23 Honeywell Honeywell Security amp Data Collection 2700 Blankenbaker Pkwy Suite 150 Louisville KY 40299 800 675 3364 www honeywellaccess com
20. the data from the MAIN PC to the REDUNDANT one 4 Follow steps 1 5 in the Pre Redundancy Section on page 14 Interim Steps Before Full Redundancy Verification 1 Shut down the Redundant PC 2 Restart all the service on the MAIN PC Launch the User Interface and verify that communications have resumed 16 Installation Guide PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Redundant Test Examples NOTE Stop watch needed for all three test examples Example 1 1 Use the MAIN PC s OFF button to shut it down Turn on the REDUNDANT PC and start the stop watch 2 Log into NT with Administrator rights 3 Launch the User Interface and log in as ADMIN 4 When the Alarm View pops up with Poll Response Normal stop the stop watch This time represents the amount of time that has passed since the MAIN PC went down Example 2 1 Unplug the power to the MAIN PC Turn on the REDUNDANT PC and start the stop watch 2 Log into NT with Administrator rights 3 Launch the User Interface and log in as ADMIN 4 When the Alarm View pops up with Poll Response Normal stop the stop watch This time represents the amount of time that has passed since the MAIN PC went down Example 3 1 Unplug the network cable from the HUB for the MAIN PC Turn on the REDUN DANT PC and start the stop watch 2 Log into NT with Administrator rights 3 Launch the User Interface and log in as ADMIN 4 When the Alarm View pops up with Poll Response No
21. this document is subject to change without notice PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Installation Guide 5 CAUTION CAUTION NOTICE NOTICE NOTICE If any damage to the shipment is noticed a claim must be filed with the responsible commercial carrier Electro static discharge can damage CMOS integrated circuits and modules To prevent damage always follow these procedures Use static shield packaging and containers to transport all electronic components including completed reader assemblies Handle all ESD sensitive components at an approved static controlled workstation These workstations consist of a desk mat floor mat and an ESD wrist strap Workstations are available from various vendors This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules when wired using metal conduit for the cabling external to the enclosure These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference that will require correction at the users ex pense This document and the data in it sha
22. uld be placed in the right most position The PRO22EN ethernet card should be mounted on the PRO221C prior to mounting in the enclosure See panel instructions Wire the readers input and output connections CHECK ALL CONNECTIONS PRIOR TO POWERING UP THE ENCLOSURE AND PANELS Wire the 12VDC AC Fail Battery Fail and tamper switch from the AL400ULX to the enclosure Make sure that the power supply is not powered up at the time Wire the 12VDC to the Panel on the far right first making sure that the polarity of the wires are correct Wire the tamper switch AC Fail and Battery Fail to assigned inputs Wire the PRO22ENC1 or PRO22bNC2 tamper switch to the tamper input located on the first panel on the right The remainder of the panels can be manually wired for power and RS 485 communica tions using 18 AWG wire The wires will be daisy chained from one panel to the next so the power and the communications are wired in parallel They may also be wired using the Auxiliary Rack Harness purchased with the equip ment This will reduce wiring time in the field since the power and RS 485 communica tions between panels is factory wired in a harness that plugs into the bottom two connectors on each panel The only field wiring required is the two wiring connections of the red and black 12VDC cables connecting the Auxiliary Rack Harness and the Rack Power Supply Harness CHECK ALL CONNECTIONS PRIOR TO POWERING UP THE ENCLOSUR
23. um rated cable just add a P to Engineered Systems part number prefix for example NC1861 BL becomes PNC1861 BL 20 Installation Guide ESG Cable Part Numbers PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Part Number Description Application Length NC1841 GY 18 AWG 4 conductor reader cable 1 000 305 m NC1861 BL 500 18 AWG 6 conductor reader cable 500 152 m NC1861 BL 18 AWG 6 conductor reader cable 1 000 305 m NC18121 YL 500 18 AWG 12 conductor keypad cable 500 152 m NC18121 YL 18 AWG 12 conductor keypad cable 1 000 305 m NCNET 1 50 ohm network cable 1 000 305 m NC2221 BR 22 AWG 2 conductor alarm cable 1 000 305 m NC1821 OR 18 AWG 2 conductor power door cable 1 000 305 m NCC59206 BK RG 59 video cable 1 000 305 m NCP1841 GY 18 AWG 4 conductor Plenum reader cable 1 000 305 m NCP1861 BL 500 18 AWG 6 conductor Plenum reader cable 500 152 m NCP1861 BL 18AWG 6 conductor Plenum reader cable 1 000 305 m NCP18121 YL 18 AWG 12 conductor Plenum keypad cable 1 000 305 m NCP18121 YL500 18 AWG 12 conductor Plenum keypad cable 500 152 m NCPNET 1 50 ohm Plenum network cable 1 000 305 m NCP2221 BR 22 AWG 2 conductor Plenum alarm point cable 1 000 305 m NCP1821 OR 8 AWG 2 conductor Plenum power door cable 1 000 305 m NC2442 TN 24 AWG 120012 8pf RS485 wire communication cable 1 000 305 m NCP2442 TN 24 AWG 120012 8pf RS485 wire communication cable 1 000 305 m PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 In
24. uts Outputs readers Comm Server G All Servers added to the Device Map use Local Machine for the Node Name NOTE Use the SQL Enterprise Manger to backup the programmed database Refer to the SQL Server Manual for instructions CAUTION If the instructions describing the Data Transformation Services are not followed exactly your database could be overwriten Second PC Installation Follow Instructions 1 through 4 and 6 through 8 listed on pages 12 and 13 Enterprise Manager Setup 1 s WO N Open up Enterprise Manager from the secondary PC the PC you will use for Redun dancy Right click and expand the SQL Server Group Right click and expand the Computer Name Group Right click on the WIN PAK PRO Database and select All Tasks then Import Data Click Next Verify that the Server is selected as MAIN The database should be WIN PAK PRO The source database PRO 2200 Enclosure PRO22ENC1 amp PRO22ENC2 Installation Guide 15 6 Click Next Change the Server to match the name of the LOCAL PC The database should be selected as WIN PAK PRO from that Server The destination database 7 Glick Next Select Transfer objects and data between SQL Server 7 0 database 8 Click Next Uncheck the Create destination objects box 9 Click Next Check the Create DTS package for replication box Also check the Save DTS Package box Leave the radial button set for SQL Server This menu saves the replication using a DTS
Download Pdf Manuals
Related Search