Hobart HCM62 User's Manual
Contents
1. HCM61 HCM62 FOOD PROCESSORS MODEL HCM61 ML 134017 HCM62 ML 134018 CORPORATION 937 332 3000 www hobartcorp com FORM 34468 Apr 2000 Installation Operation and Care of HCM61 amp HCM62 Food Processors SAVE THESE INSTRUCTIONS GENERAL The model HCM61 and HCM62 Food Processors are used for chopping meat fish fruits vegetables nuts or dry bread for mixing various Sauces mayonnaise or soups or for blending or pureeing various products such as thickening or desserts Refer to Capacity Recommendations page 6 The HCM61 has a 1 5 HP motor is provided with 120 Volt cord and plug and requires a 20 Amp electrical service and receptacle The machine operates at 1700 rpm with single speed or pulse control The HCM62 has a 2 0 HP motor is provided with 208 240 Volt three phase cord and plug and requires a 20 Amp electrical service and receptacle The machine operates at 1700 or 3400 rpm with two speed or pulse control Model HCM61 or HCM62 Food Processor INSTALLATION UNPACKING Immediately after unpacking the food processor check for possible shipping damage If this machine is found to be damaged after unpacking save the packaging material and contact the carrier within 15 days of delivery Prior to installation test the electrical service to assure that it agrees with the specifications on the machine data plate Lift or move the machine only by using the two handles on the sides of the bas2. had BOWL B 5 lt COVER E HANDLE Fig 4 PRESS HANDLE DOWN a THEN TURN CLOCKWISE 1 8 TURN A TO ENGAGE Fig 5 SCRAPER ARM ae HANDLE p BOWL COVER HANDLE ALIGNMEMT OPERATION WARNING ROTATING KNIVES INSIDE DO NOT OPEN COVER UNTIL KNIFE SHAFT STOPS UNPLUG CORD BEFORE INSERTING OR REMOVING ATTACHMENTS CLEANING OR SERVICING CONTROLS Model HCM61 OFF Machine is OFF Switch machine OFF before unpluging ON Runs motor and knife at 1700 rpm until switch is turned to OFF PULSE Runs motor and knife at 1700 rpm while switch is held When switch is released machine returns to OFF Model HCM62 OFF Machine is OFF Switch machine OFF before unpluging LOW Runs motor and knife at 1700 rpm until switch is turned OFF HIGH Runs motor and knife at 3400 rpm until switch is turned OFF PULSE Runs motor and knife at 1700 rpm while switch is held When switch is released machine returns to OFF When processing is done turn Arm to rear Wait for Knife to stop Unplug machine power cord Lift the Bowl Cover Scraper Handle and Bowl Scraper straight up Remove the Knife Shaft The Bowl can be removed to empty contents CAPACITY RECOMMENDATIONS The maximum quantity that can be processed at one time and the length of time required for processing are dependent on the product and kind of result desired Shorter processing times give a coarser result longer processing yields a finer consistenc
3. TUBE The Bowl Cover is equipped with a Lid Plug which can be pulled open for adding ingredients When replacing the Lid Plug be sure to turn the Lid Plug so the underneath side of the plug is flat with the underneath side of the Bowl Cover With the Lid Plug in closed position the Scraper Handle should move back and forth over it CLEANING WARNING SWITCH OFF AND UNPLUG MACHINE POWER CORD BEFORE BEGINNING ANY CLEANING PROCEDURE The food processor should be thoroughly cleaned after use Never use steel wool abrasive cleaning sponges or high pressure hose for cleaning Do not leave the knife shaft wet or setting on a stainless steel worktop when not in use Swing the Arm to the rear as far as it will go Remove the Bowl Cover Bowl Scraper Scraper Handle by lifting straight up out of the Bowl Set the assembly on a table or countertop Fig 8 Press the Scraper Handle down Fig 8 freeing the tabs of the Scraper Handle Shaft from the slot restrictions in the Bowl Scraper While pressing down turn the Scraper Handle counterclockwise s turn Remove the Scraper Handle Separate the Bowl Cover and Bowl Scraper Remove the Bowl Scraper Wipers from the grooves of the Bowl Scraper Remove the Knife Shaft by lifting it straight up Remove the Bowl Remove the Bowl Cover Gasket from the Bowl Cover by grasping the gasket with your finger and thumb at the Indentation where the Gasket Groove is not present Fig 9 Wash rinse and
4. sanitize all parts in a sink as you would any food utensil and allow to air dry Wipe the exterior of the machine with adamp cloth Reassemble all parts when dry following the Bowl and Knife Assembly instructions on pages 4 5 ay a PRESS HANDLE DOWN sa THEN TURN COUNTERCLOCKWISE 1 8 TURN PS TO RELEASE Fig 8 GASKET GROOVE Ta f S W INDENTATION TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SUGGESTED CORRECTIVE ACTION Machine won t start Fuse or circuit breaker L MAN Have electrician check circuit interrupting power Bowl not in place Make sure bowl is in proper position Arm not in position over Make sure Arm is in proper position over center of Bowl center of Bowl Cover Cover and Top of Core of Scraper Handle Machine not plugged in Plug into proper mating electrical receptacle Machine stops while deor ovenoaded Allow motor to cool motor will restart when it is cool operating and won t restart l It may take 10 to 30 minutes for the motor to cool Fuse or circuit breaker nae PAE l Have electrician check circuit interrupting power SERVICE Contact your local Hobart authorized service office for any repairs or adjustments needed on this equipment FORM 34468 Apr 2000 8 PRINTED IN U S A
5. to verify that the knife rotates counterclockwise as viewed from the top PRESTART CHECK With the machine fully assembled pages 4 5 make sure the cutting blades stop within 4 seconds after the arm is swung back away from the center of the bowl cover Make sure the machine cannot be started with the bowl and cover removed but with the arm swung into position above the center of the drive shaft If the machine fails to work properly contact Service do not allow the machine to be operated BOWL AND KNIFE ASSEMBLY a AM l MOTOR SHAFT Install the Bowl so the center post of the Bowl fits over the motor shaft one of the Bowl Pins fits in the slot at the front of the machine and the bowl handles are positioned on left and right Fig 1 oe Te a Install Knife Shaft over center bowl post so the 3 j 4 Val slots on the Knife Shaft fit the grooves on the sse o motor shaft Fig 1 KNIFE SHAFT BOWL HANDLE BOWL PIN Fig 1 as Y slightly toward the center Fig 2 the ends of the SCRAPER wipers are vertical so they do not interfere with the lip of the Bowl Cover Do not install the wipers backwards L The four Bowl Scraper Wipers must be properlv installed in the grooves of the Bowl Scraper The upper tips of the wipers point straight up and Fig 2 BOWL COVER BOWL COVER GASKET After installing the Lid Plug turn it so the underneath side of the plug is flat with the underneath side of the B
6. e LOCATION Place the food processor on a suitable sturdy worktop or table There should be adequate space around the machine for the user to operate the controls and install and remove the bowl and knife HOBART CORPORATION 2000 ELECTRICAL CONNECTIONS Cord Connected Machines WARNING THE ELECTRICAL CORD ON THIS MACHINE IS EQUIPPED WITH A GROUNDING TYPE PLUG WHICH MUST BE CONNECTED TO A PROPERLY GROUNDED RECEPTACLE IF THE RECEPTACLE IS NOT THE PROPER GROUNDING TYPE CONTACT AN ELECTRICIAN DO NOT REMOVE THE GROUNDING PRONG FROM THE PLUG Refer to the machine data plate and Electrical Data below ELECTRICAL DATA Minimum Circuit Ampacity Model vot Hertz Phase Maximum Protective Device Receptacle AMPS HCM61 120 60 1 Plug 5 20P 5 20R 208 240 60 3 Plug L15 20P Compiled in accordance with the National Electrical Code NFPA70 latest edition CHECK MOTOR ROTATION Three Phase Machines Only On model HCM62 check the rotation With all parts in their normal operating positions pages 4 5 turn the switch to the Pulse position for two seconds and release The direction of rotation of the knife should be counterclockwise as viewed from the top If the knife rotates clockwise correct the rotation using the following procedure DISCONNECT THE ELECTRICAL POWER SUPPLY Interchange any two of the incoming power supply leads in the plug Reconnect the power supply and turn the switch to the Pulse position
7. owl Cover Fig 3 The Bowl Cover Gasket must be properly installed in the groove around the lip of the Bowl Cover Fig 3 LID PLUG Fig 3 Fit the Bowl Cover over the Bowl Scraper so the center holes align Fit the Scraper Handle Shaft through the center hole in the Bowl Cover into the Slots of the Bowl Scraper The Bowl Cover Tab must fit around the 180 Cam on the Scraper Handle The Tabs on the Scraper Handle Shaft must fit through the Slots in the center hole of the Bowl Scraper Place the assembled Bowl Cover Bowl Scraper Scraper Handle ona flat surface Press down on the Scraper Handle Fig 5 and turn it clockwise sturn so the Tabs engage with the bottom of the Slots The Bowl Cover Bowl Scraper Scraper Handle are now joined as one piece Move the Scraper Handle until it is positioned over the Lid Plug Place the assembled Bowl Cover Bowl Scraper Scraper Handle in the Bowl The Bowl Scraper Legs touch the sides of the Bowl The Bowl Cover Handles set directly above the Bowl Handles Fig 6 The Alignment Pins under the Bowl Cover Handles fit the holes in the Bowl Handles Fig 6 Swing the Arm forward so the end of the Arm fits over the center of the Bowl above the Scraper Handle Fig 7 The Arm must be properly positioned over the center of the Bowl and all parts must be properly assembled before the machine will operate SHAFT SCRAPER HANDLE 180 CAM TAB z
8. y The Capacity Chart shows the maximum quantity of various products that can be processed in one batch and the approximate processing time CAPACITY CHART Mince Chop Onions 3 pounds Carrots 3 pounds Mozzarella Cheese 3 pounds 20 seconds 20 seconds 20 seconds 3 pounds 30 seconds Salmon Mousse Steak Tatar Bread Crumbs Parmesan Cheese fine Butter Mayonnaise Tomato Sauce Liquid 41 2 pounds 3 2 pounds 3 pounds 1 2 pounds 1 2 pounds 4 pounds 4 2 quarts 4 2 quarts 4 2 quarts 30 seconds 30 seconds 30 seconds 10 seconds 1 minute 30 seconds 35 seconds 20 seconds as required PREPARING THE PRODUCT FOR PROCESSING Cut products such as meat and cheese into equal pieces of approximately 1 cubes for easy processing For bread crumbs or other dry products place product into the bowl first turn the machine on then add liquid ingredients For pureeing products be sure to move the Scraper Handle back and forth to reintroduce partially cut product into the cutting zone USING THE BOWL SCRAPER DURING PROCESSING During processing move the Scraper Handle back and forth to reintroduce partially cut product that is clinging to the sides of the bowl back into the cutting area The Bowl Scraper can also be used during processing to stir or mix liquid products The Bowl Scraper has four legs and four lid wipers this allows a 90 motion to fully wipe the entire Bowl and lid USE OF THE FEED
Download Pdf Manuals
Related Search