Havis-Shields KK-K9-F12-K User's Manual
Contents
1. 10 i i i stainless flat washers Note this is for easy window cleaning 8 Final steps e Mount dome light fan if necessary switch box as desired A switch box is provided so switch can be mounted to K 9 housing in various locations Topside of tunnel housing works very well Wire to 12 volt power source e Sheet metal seams and gaps need to be carefully silicone at floor area Proper sealing of w ee compartment will eliminate water from getting Iae under the K 9 unit Adhesive Molding e Allow silicone to dry overnight before placing in rubber floor mat tt t 4 KKK NM gt Nttatate OK Pinte KY ty if K t KK K9 F12 K INST 6 06 Consolidator Kwik Raze Collins Dynamics Kwik Kit PrisonerTransports K 9Transports 75 Jacksonville Rd PO Box 2099 Warminster PA 18974 800 524 9900 215 957 0720 P 215 957 0729 F www Havis com2. Havis Shields EQUIPMENT CORPORATION INSTALLATION INSTRUCTIONS KK K9 F12 K 2000 2006 FORD EXCURSION TOOLS REQUIRED Power Drill Ratchet Wrench With 6 Extension Standard amp Metric Socket Sets Torx Bit Set Phillips Screw Driver 4 Hole Saw Exhaust Fan Option 7 16 Wrench Caulk Gun Wire Cutters Crimping tool HARDWARE Some of this hardware is already attached QTY DESCRIPTION PART 28 4 20 X 2 Stainless carriage bolts GSM 32022 30 4 20 X 3 2 Stainless carriage bolts GSM 32024 64 14 20 Serrated nuts GSM 30023 6 74 2 X 4 Hex head Cap Screw Zinc GSM33001 14 7a X 1 A Hex head lag screw GSM 33062 36 12 X 3 2 Stainless sheet metal screws GSM 34177 24 10 X 3 2 Stainless sheet metal screws GSM 34170 2 10 X Stainless sheet metal screws GSM 34169 6 10 X 3 2 Sheet metal screws GSM 33195 20 10 X Sheet metal screws GSM33194 l Tube Silver Caulk PRM 97343 l 46 X 45 1 2 Rubber Mat KNM01029 SUV 11 1 2 feet Adhesive Molding SUB ASSEMBLY e Dome light with wire e Tunnel edge molding e Install exhaust fans Optional If locating in custom location drill 4 4 hole into desired location of K 9 housing Mark and drill 3 16 mounting holes to attach fan using 4 10 32 X 2 machine screws and 10 32 keps nuts Then mark and drill 3 16 holes to mount fan guard using 10 32 X 1 2 machine screws and 10 32 keps nuts INSTALLATION 1 Remove int
3. L ATAA la i i 4 H fy ghat r Tih a W K s TaiTaTi J i HHH 4 LA a a y 4 i a i Oia ais HRRE HRA giit 4 i G 4 t Note If 32 inch long K 9 kit is being installed a 10 rear floor extension must be used provided with 32 kits 4 a E 4 t te ay 4 ts 4 a aA ca RRAS Y d BOOK t iJ i RRRA tt AA t E ot Ny A H ft 4 i t i 4 te Wy Wiis wu 7 Door panels and window guards e Center door panels so edges do not hang over e Attach to door with 10 x 1 2 stainless sheet metal screws Note window guards have holes around perimeter for permanent mounting These holes are not used with hinge kit They also come flat in shipping The guard must be pre bent so it fits tight against the door window frame Hold window guard with pre assembled hinge and upper bracket onto window frame Make sure guard is centered on window Attach hinge to lower door panel with 10 x 4 sheet metal screws Mark upper aluminum bracket location on window frame and remove from window guard e Attach aluminum bracket onto window frame with 10 x 4 sheet metal screws e Apply adhesive molding to inner side of window q i j guard i e Hinge up window guard and reattach to bracket PEE wanow Bracket with 10 x stainless machine screws and
4. erior e Remove rear seats e Remove rear seat belt assembly e Remove top and bottom plastic rear trim caps 2 Remove rear OEM door panels e Remove speaker door handle and lock e Remove switch assembly from plastic housing leave plug on switch Note if doors have electric door switches they must be reattached to original plug assembly Switch assembly must then be wired tied down so it does not interfere with window or door latch operations 3 Install mounting legs e Using 4 20 x 4 carriage bolts attach mounting legs to floor of vehicle using 1 4 x 1 2 hex head lag screws Note keep nuts loose at this time And set legs at 6 1 2 high 4 Slide in K 9 main housing e Slide in main housing e Housing should be 48 1 2 from rear plastic sill to rear mounting flange e Mount legs to housing loosely using 4 20 x 74 carriage bolts e Mount rear support to bottom of rear housing using 6 4 20 x 3 4 hex head cap screw 5 Install tunnels and fillers e Loosely attach side tunnels to main housing using 14 20 x 3 2 carriage bolts and 4 20 x 4 carriage bolts e Place sill plate and cover step in tunnels and mount with 12 x 3 4 stainless sheet metal screws 6 Housing final step e Center housing so cover steps are even on both sides e Mount rear housing to vehicle with 1 4 x 1 2 hex head lag screw e Tighten all loose bolts on tunnels and legs i
Download Pdf Manuals
Related Search