Harbor Freight Tools Folding Clamping Workbench with Movable Pegs Product manual
Contents
1. 2 Attach the Cross Bar 7 to each Leg Frame 8 Use Bolts 4 Washers 5 and Nuts 6 See photo B Tighten securely The Leg Frames 8 are labeled left L and right R and must be aligned before placing the Cross Bar 3 Push the Rubber Pads 9 onto the Leg Frame 8 feet See photo B SKU 47844 Page 4 4 With the Table Top still upside down slide the Leg Frames 8 into the Slide Base 3 as shown in photos A and C Both Slide Base handles should face forward Guide the Bolts 10 with Washer 11 into the Slide Base side holes from the outside and through the Leg Frames With the Bolts protruding out from the other side of the Slide Base insert Washer 11 and Nuts 12 Tighten securely A Toe SP PE INAS Re Seam s 5 Attach the Handles to each Slide Base 3 if not already attached Turn each Handle to widen the Table Top 6 Place the Workbench right side up and place the four Material Stops 13 in the desired location See photo D Locate the Foldable Workbench on a flat level solid surface that is capable of supporting the workbench and its maximum weight capacity oFf 260 Ibs 7 When you are finished using the Workbench press down on one side of the Table Top to collapse and fold the Workbench for storage See photo E 8 Store in a clean and dry location PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL2. Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically non conductive clothes and non skid footwear are recommended when working Wear restrictive hair covering to contain long hair SKU 47844 Page a Rev 08a 10 11 12 13 14 15 16 17 18 19 20 Use eye and ear protection Always wear ANSI approved impact safety goggles Wear a full face shield if you are producing metal filings or wood chips Wear an ANSI approved dust mask or respirator when working around metal wood and chemical dusts and mists Do not overreach Keep proper footing and balance at all times Do not reach over or across running machines Be careful of pinching fingers when working with the Foldable Workbench Maintain tools with care Keep tools sharp and clean for better and safer performance Follow instructions for lubricating and changing accessories Inspect tool cords periodically and if damaged have them repaired by an authorized technician The handles must be kept clean dry and free from oil and grease at all times Disconnect power Unplug tools when not in use Remove adjusting keys and wrenches Check that keys and adjusting wrenches are removed from the tool or machine work surface before plugging it in Avoid unintentional starting Be sure tool switches are in the Off position when not in use and before plugging in Do not carry any tool with your finger
3. on the trigger whether it is plugged in or not Stay alert Watch what you are doing use common sense Do not operate any tool when you are tired Take caution as some woods contain preservatives such as copper chromium arsenate CCA which can be toxic When cutting these materials extra care should be taken to avoid inhalation and minimize skin contact Check for damaged parts Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Guard against electric shock Prevent body contact with grounded surfaces such as pipes radiators ranges and refrigerator enclosures Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools Do not operate tools if under the influence of alcohol or drugs Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the tool Maintenance For your safety service and maintenance should be perfo
4. AS A REFER ENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WAR RANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDER TAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 47844 Page 5 REV 10c Parts List aty Washer 12 x 6 mm Nuts M6 Leg Frame Stops Material 4 Cross Bar NOTE Some parts are listed and shown for illustration purposes only and are not available individually as re placement parts Assembly Photo REV 10c SKU 47844 Page 6 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear an
5. US GENERAL FOLDABLE WORKBENCH ASSEMBLY AND OPERATING INSTRUCTIONS Visit our website at http www harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2002 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork con tained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included For technical questions or replacement parts please call 1 800 444 3353 Revised Manual 10g Specifications Weight Capacity 260 Ib dead weight 25 1 8 L x 19 7 8 W x 30 7 8 H with chocks 29 7 8 H without chocks Table Adjustment Range 12 5 8 outside to outside and 3 3 4 inside to inside Table Adjustment Width 9 3 8 minimum Table Dimensions 23 7 8 L x 4 11 16 W x 3 4 H Overall Dimensions Table Top Material Veneered Birch 28 118 Lx 1 6a Weight 12 5 Ib Protractor Scale 24 ruler also Metric Foldable Vise Features Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagra
6. d tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 REV 10g SKU 47844 Page 7
7. m Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference Safety Warnings and Precautions WARNING When using tools with this product basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment Read all instructions before using tools with this product 1 Keep work area clean Cluttered areas invite injuries 2 Observe work area conditions Do not use machines or power tools in damp or wet locations Don t expose to rain Keep work area well lighted Do not use electrically powered tools in the presence of flammable gases or liquids 3 Keep children away Children must never be allowed in the work area Do not let them handle machines tools or extension cords Do not allow children to play with the Foldable Workbench 4 Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children 5 Use the right tool for the job When using tools with this product do not attempt to force a small tool or attachment to do the work of a larger industrial tool There are certain applications for which this tool was designed It will do the job better and more safely at the rate for which it was intended Do not modify this product and do not use it for a purpose for which it was not intended 6
8. rmed regularly by a qualified technician Use proper size and type extension cord If an extension cord is required it must SKU 47844 Page 3 be of the proper size and type to supply the correct current to the tool without heating up Otherwise the extension cord could melt and catch fire or cause electrical damage to the tool Longer extension cords require larger size wire If you are using the tool outdoors use an extension cord rated for outdoor use signified by WA on the jacket 21 Pacemaker safety warning People with pacemakers should consult with their physician s before using certain electric tools operation of equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker Warning The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be under stood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Unpacking When unpacking check to make sure that all the parts are included Refer to the Parts List lf any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual as soon as possible Assembly 1 Turn the Table Top 1 pieces upside down and attach each Slide Base 3 as shown below Use the Wood Screws 2 See photo A Tighten securely
Download Pdf Manuals
Related Search