Harbor Freight Tools Adjustable Steel Welding Table Product manual
Contents
1. 8 Part Description Qty 6 Angle Bracket _ 2 8 NutM8 mm _ 1 9 BoltM8x45mm_ 2 12 Bolt M8x50mm_ 6 Record Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Page 6 For technical questions please call 1 888 866 5797 Item 61369 Assembly Diagram For technical questions please call 1 888 866 5797 Page 7 Item 61369 Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY2. For technical questions please call 1 888 866 5797 Page 3 Table Top Bracket Assembly Bolt 19 Attach the two Table Top Brackets 4 to the bottom of the Table Top 1 using four Washers 2 Nuts 5 and Bolts 19 Note that the Washers are placed between the Table Top and the Table Top Brackets See Figure D eye Nut 5 Figure D Attaching the Table Top The two Angle Brackets each have five positive stop positions which allow the Table Top once attached to be positioned at five different A angles Prior to attaching the Table Bracket Top ensure that the Brackets are set in the middle position and that the Angle Adjustment Handles are tightened securely See Figure E 1 With assistance lift the Table Adjustment Top and place in position over Handle 10 the upright table stand 2 Insert four Bolts 3 through the Angle Brackets and Table Top Brackets and secure in place using four Washers 7 and Nuts 8 Tighten all hardware See Figure E Figure E g Table Top Bracket 4 Table Top 1 Table Top Bracket 4 Page 4 For technical questions please call 1 888 866 5797 Item 61369 Installing the Guide Rails Lever Bolt 17 Ty Short Guide A Rail 23 Table Top 1 P 1 Place four Washers 2 on the shafts of the four Lever Bolts 17 2 Attach the Short Guide Rail 23 Cer and the Lon
3. ATION Assembly Precautions 1 Assemble only according to these instructions 4 Keep bystanders out of the area during assembly Improper assembly can create hazards 5 Do not assemble when tired or when under the Wear ANSI approved safety goggles and influence of alcohol drugs or medication heavy duty work gloves during assembly N 6 Weight capacity and other product capabilities apply 3 Keep assembly area clean and well lit to properly and completely assembled product only Use Precautions 1 This product is not a toy Do not allow 5 Do not exceed listed weight capacity Tighten children to play with or near this item all knobs securely before applying load Be aware of dynamic loading 2 Use as intended only Do not sit or stand on Table Sudden load movement may briefly create 3 Inspect before every use do not use excess load causing product failure if parts are loose or damaged 6 Maintain product labels and nameplates 4 Use only on flat level hard surface These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement Assembly Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagram near the end of this manual U
4. IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state CHICAGOG acd WELDING 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 1 888 866 5797
5. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference eierne WELDING Adjustable Steel WELDING TABLE Visit our website at http www harborfreight com REV 44d k Email our technical support at productsupport harborfreight com ITEM 61369 When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 888 866 5797 as soon as possible Copyright 2013 by Harbor Freight Tools All rights reserved f F No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Specifications Table Top Dimensions 30 x 19 7 8 Table Height 32 7 8 Maximum Weight Capacity 350 Ib IMPORTANT SAFETY INFORM
6. g Guide Rail 18 in the desired position on the Table Top using the four Lever Bolts and Washers See Figure F Long Guide Rail 18 Figure F Maintenance Inspection Maintenance and Cleaning 1 BEFORE EACH USE inspect the general 2 AFTER USE wipe external surfaces condition of the Welding Table Check for of the Table with clean cloth e loose hardware misalignment or binding of parts e cracked or broken parts e any other condition that may affect its safe operation Item 61369 For technical questions please call 1 888 866 5797 Page 5 Parts List and Diagram PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Parts List Part Description Qty 2 Washer 6 5x1 5mm _ _ 8 5 NutM5mm _
7. nwrap and separate all parts on a clear work area Vertical Post Angle Bracket Assembly Attach the two Angle Brackets 6 to the Vertical Posts 20 using one Washer 7 Nut 8 and Bolt 9 per Post Bracket assembly See Figure A Angle Bracket 6 S Bolt 9 Vertical Post 20 Figure A Page 2 For technical questions please call 1 888 866 5797 Item 61369 Support Leg Assembly Attach the two Vertical Post Angle Bracket assemblies from the previous step to the two Support Legs 13 using four Washers 7 Nuts 8 and Bolts 12 See Figure B 6 Vertical Post Angle Bracket P SY Assemblies y Bolt 12 Tool Hanger Support Brace Angle Handle Assembly Bolt 12 3 Welded nut for Gas Handle Bolt tog lt P ZO 1 Attach the Tool Hanger 16 Pande tid Washer to the Support Leg which has four threaded holes using four Bolts 15 See Figure C 2 Attach the Support Brace 21 to the Vertical Posts using two Washers 7 Nuts 8 and Bolts 22 See Figure C 3 Insert a Bolt 12 through the back of each of the two Angle Adjustment Handles 10 Slide a Washer 11 over each Bolt with the cupped side of the Washer against the Handle Insert the Bolts through the Angle Brackets and thread into the nut welded to the Vertical Post See Figure C 11 Bolt 15 Figure C Support Leg 13 Item 61369
Download Pdf Manuals
Related Search