Harbor Freight Tools 97385 User's Manual
Contents
1. the two Adjusting Screws 3 to secure the Router Table Fence in place Always tighten both Adjusting Screws to ensure a secure connection See Assy Diagram An additional adjustment may be made to where you need to stop your material Loosen the Knob 11 on Page 5 the C Clamp 9 Slide the End Slide 6 to the right or left along the Fence Slides 5 to the point at which you need to stop your material Then retighten the Knob 11 to secure the End Slide 6 in place See Assy Diagram 4 NOTE The End Slide 6 may be in serted in either the left or right side of the Fence Slides 5 depending upon the application See Assy Diagram MAINTENANCE AND SERVICING Procedures not specifically explained in this manual must be performed only by a qualified technician TO PREVENT AWARNING serious INJURY FROM ACCIDENTAL OPERATION Turn the Power Switch of the router or drill press to its OFF position and unplug the machine from its electrical outlet before performing any inspection maintenance or cleaning procedures TO PREVENT SERIOUS INJURY FROM EQUIPMENT FAILURE Do not use damaged equipment If abnormal noise or vibration occurs have the problem corrected before further use SKU 97385 For technical questions please call 1 800 444 3353 Inspection Maintenance And Cleaning 1 BEFORE EACH USE inspect the general condition of the Router Table Fence Check for loose scre2. 2 See Assy Diagram Attach the C Clamp 9 onto the Carriage Screws 14 noting that one end is locked into the slot in the Fence 1 and the other end rests on the Extension Rod 8 Attach a Washer 15 and Knob 11 and tighten See Assy Diagram Position a Guide 2 under the Fence 1 Insert T Screw 4 from under neath through Guide 2 Fence 1 and Washer 15 Screw Lock Knob 3 onto T Screw 4 and tighten clockwise Attach the other Guide using the same procedure To at tach and secure the Router Table Fence on a Router Bed slide the two Guides 2 onto the rails on the Rout er Bed See Assy Diagram OPERATING INSTRUCTIONS A AWARNING a For technical questions please call 1 800 444 3353 Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Tool Set Up TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION Make sure the power switch of the router or drill press is in its OFF position and the machine is unplugged from its electrical outlet before performing any set up procedures After the Router Table Fence is mounted to the router drill press table top adjust the Router Table Fence by loosening the two Adjusting Screws 3 See Assy Diagram Slide the Router Table Fence forward or backward to where you need to stop your material Then tighten
3. CENTRAL MACHINERY ROUTER TABLE FENCE exe 33197385 SET UP AND OPERATING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http www harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2007 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 SAVE THIS MANUAL Neile NOTICE is used to address practices Keep this manual for the safety warn not related to personal injury ings and precautions assembly operating inspection maintenance and cleaning pro CAUTION CAUTION without cedures Write the product s serial number the safety alert in the back of the manual or month and symbol is used to address year of purchase if product has no num practices not related to ber Keep this manual and the receipt in personal injury a safe and dry place for future reference General Safety Rules IMPORTANT SAFETY WARNING Read all instructions ___INFORMATION A isted be
4. M SKU 97385 For technical questions please call 1 800 444 3353 Page 7 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this prod uct is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESS LY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the com plaint must accompany the merchandise If our inspection verifies the defect we will ei ther repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and
5. ectrical outlet before assembling or making any adjustments to the Router Table Fence A Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagram near the end of this manual Assembly To Install The Vacuum Attachment 1 Slide the head of two Carriage Screws 13 into the center channel of the Fence Slide 5 Repeat the same procedure for the other Fence Slide but insert a Carriage Screw 14 as well Guide the four shorter Screws into the center and adjacent two holes in the Fence 1 See Assy Diagram Page 4 SKU 97385 Insert the Vacuum attachment 12 onto the center Screws Attach one Washer 15 onto each Screw Attach the Slide Knobs 10 to the Screws and tighten See Assy Diagram Insert the Extension Rods 2 into the outer channels of the Fence Slide 5 at the Fence 1 side See Assy Diagram Slide the head of the Carriage Screws 14 into the center channel of the End Slide 6 See Assy Diagram Attach the Block Stop 7 to the protruding Carriage Screw 14 while aligning the tangs on the Block Stop with the center channel face of the Fence Slide 5 Attach a Flat Wash er 15 and Knob 11 to the Screw and tighten NOTE The Block Stop slides through the entire length of the Fence Slide Use the Block Stop for repeti tive work If not needed loosen the securing Knob 11 and slide the as sembly off the Fence Guide
6. hnical questions please call 1 800 444 3353 Page 2 a SKU shoes hard hat or hearing protec tion used for appropriate conditions will reduce personal injuries Do not overreach Keep proper foot 4 ing and balance at all times This enables better control of the Router Table Fence in unexpected situa tions Dress properly Do not wear loose clothing or jewelry Keep your hair clothing and gloves away from mov ing parts Loose clothes jewelry or long hair can be caught in moving parts 1 Equipment use and care Do not force the Router Table Fence Use the correct equipment for your application The correct equipment will do the job better and safer at the 2 rate for which it was designed Store idle equipment out of the 3 reach of children and do not allow people unfamiliar with the Router Table Fence or these instructions to 4 operate the equipment This product can be dangerous in the hands of untrained users 5 Maintain the Router Table Fence Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the equipment s operation If dam aged have the equipment repaired before use Many accidents are caused by poorly maintained equip ment Use the Router Table Fence in ac cordance with these instructions and in the manner intended for the particular type of equipment taking into account the working conditions and the
7. low may result in serious injury The term equipment in all of the warnings listed below refers to your Router Table Fence SAVE THESE INSTRUCTIONS In this manual on the labeling and all other information provided with this product This is the safety alert symbol It is used to alert you to potential personal 1 Work area safety injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death a Keep work area clean and well lit Cluttered or dark areas invite acci dents b Keep children and bystanders away while operating this equipment 7 Ney Ne De edie Distractions can cause you to lose a hazardous pae situation which if not i avoided will result in deathor 2 Personal safety PRASUN a Stay alert watch what you are doing WARNING and use common sense when op AWARNING indicates a erating this equipment Do not use hazardous situation which if the Router Table Fence while you not avoided could result in are tired or under the influence of death or serious injury drugs alcohol or medication A mo SATON aes ment of inattention while operating U this equipment may result in serious ACAUTION with the safety personal injury alert symbol indicates a b Use safety equipment hazardous situation which if Always wear eye protec not avoided could result in f tion Safety equipment mingrormoderateinjiy such as dust mask non skid safety SKU 97385 For tec
8. quickly provide you with a replacement We will return re paired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not avail able individually as replacement parts SKU 97385 For technical questions please call 1 800 444 3353 Page 8
9. quipment such as those dust masks that are specially designed to filter out microscopic particles California Health amp Safety Code 25249 5 et seq 6 The warnings precautions and in structions discussed in this instruction manual cannot cover all possible con ditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SAVE THESE INSTRUCTIONS SPECIFICATIONS o apse 36 3 4 L x 4 1 8 W x 4 1 8 H Dimensions Extended Fence 23 13 16 L x 2 1 8 W x 1 7 8 Dimensions H T Slots to Accept Featherboards or Stops Independently Adjustable Fence Halves Fence Extension amp Material Stop Additional Features UNPACKING When unpacking check to make sure that the item is intact and undamaged If any parts are missing or broken please call Harbor Freight Tools at the number shown on the cover of this manual as soon as SKU 97385 For technical questions please call 1 800 444 3353 possible INITIAL SET UP INSTRUCTIONS Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product TO PREVENT AWARNING serious INJURY FROM ACCIDENTAL OPERATION Turn the Power Switch of the router or drill press to its OFF position and unplug the tool from its el
10. work to be performed Use 97385 For technical questions please call 1 800 444 3353 of the Router Table Fence for opera tions different from those intended could result in a hazardous situation Service a Maintain the Router Table Fence according to the instructions on page 6 of this manual Use only identical replacement parts This will ensure that the safety of the equipment is maintained Specific Safety Rules Maintain labels and nameplates on the Router Table Fence These carry important safety information If un readable or missing contact Harbor Freight Tools for a replacement This product is not a toy Keep it out of reach of children Secure the Fence firmly to a router table or drill press table before use Read the manual of the router or drill press used with the Fence before use Some dust created by power sand ing sawing grinding drilling and other construction activities contains chemicals known to the State of Cali fornia to cause cancer birth defects or other reproductive harm Some examples of these chemicals are e Lead from lead based paints e Crystalline silica from bricks and ce ment or other masonry products e Arsenic and chromium from chemi cally treated lumber Your risk from these exposures var ies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with Page 3 approved safety e
11. ws mis alignment or binding of moving parts cracked or broken parts damaged and any other condition that may af fect its safe operation 2 AFTER USE clean external surfaces of the Router Table Fence with a clean moist cloth and mild detergent Then dry Do not use solvents 3 WHEN STORING keep the Router Table Fence in a clean dry safe loca tion out of reach of children and other unauthorized people PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Page 6 PARTS LIST Da rence o i a 2 foe i a e foa 4 tsoew amay f s Feness f gt e endside fr _ exensionRod gt o fece fr a0 sieks fa mpo o fee a3 Camiage Screw 1x20 x 3w 5 Cas FiatWasher a e ASSEMBLY DIAGRA
Download Pdf Manuals
Related Search