Harbor Freight Tools 93302 User's Manual
Contents
1. Gun Assembly 6 to completely de pressurize the system Remove the Cap 2 from the Tank Check to make sure the Filter 3 is clear of dirt and debris Refill the Tank with liquid and replace the Cap Pump the Hand Pump Assembly 5 to pressurize the system and continue spraying See Assy Diagram When finished spraying de pressurize the system Remove the Cap 2 from SKU 93302 For technical questions please call 1 800 444 3353 PAGE 6 the Tank 1 and empty any remaining liquid into a safe and secure container Clean the Sprayer thoroughly with agents recommended by the chemical manu facturer Allow the unit to air dry Replace the Cap and store the Sprayer ina clean dry safe location out of reach of children See Assy Diagram TROUBLESHOOTING Possible Solution Unit does not spray Make sure there is an adequate amount of liquid in the Tank Pump the Hand Pump Assy to pressurize the system Do not squeeze the Trigger on the Spray Gun Assembly when performing this procedure Make sure the Cap is screwed on tightly Make sure all connections to the Tank are secure Make sure all connections on the Spray Gun Assy are secure Make sure the Nozzle on the Spray Gun Assy is clear of dirt and debris The spray pattern is undesirable Adjust the Nozzle on the Spray Gun Assy toa pinpoint or fan pattern Make sure the Nozzle on the Spray Gun Assy is clear of dirt and debris INSPECTION MAINT2. ENANCE AND CLEANING ie CAUTION Always de pressurize the system before performing any inspection maintenance or cleaning of the Sprayer 2 Before each use inspect the general condition of the Sprayer Check for misalignment or binding of moving parts damaged or loose parts dirt or debris in the Filter and any other condition that may affect the tool s safe operation If abnormal noise or vibration occurs have the problem corrected before further use Do not use damaged equipment 3 Periodically lubricate all moving parts of the Handle Pump Assembly 4 To clean If using liquid chemicals flush the interior and clean the exterior of the SKU 93302 For technical questions please call 1 800 444 3353 PAGE 7 Sprayer and its Spray Gun Assembly thoroughly with cleaning agents recom mended by the chemical manufacturer Then allow to air dry Do not use sol vents 5 When storing Always completely empty the Sprayer of liquid Frost will dam age the Sprayer if the unit contains liquid Store the Sprayer in an indoor area such as a garage or shed Make sure to store the Sprayer and any chemi cals in a safe dry clean location out of reach of children A CAUTION All maintenance service and repairs not discussed in this manual should only be performed by a qualified service technician PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN TH
3. IS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 93302 For technical questions please call 1 800 444 3353 PAGE 8 PARTS LIST AND ASSEMBLY DIAGRAM Part Description Qty Part Description Qty 1 Tank tS Hand Pump Assembly 1 2 Cap 1 f6 Spray Gun Assembly 1 3 Filter 1 7 Strap Assembly o 4 Tues i o d S Includes Handle Wand and Hose FRONT VIEW 2 3 FILTER NOT SHOWN REAR VIEW NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts SKU 93302 For technical questions please call 1 800 444 3353 PAGE 9
4. cals in the Sprayer after use 18 Make sure to clean the Filter of the Sprayer before each use 19 Never leave the Sprayer unattended When finished using the Sprayer empty the unit Thoroughly clean the unit and store it in a clean dry safe location out of reach of children Z WARNING The warnings and cautions discussed in this manual cannot cover all possible conditions and situations that may occur It must be under stood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator 20 ASSEMBLY AND OPERATING INSTRUCTIONS il Prior to use the Wand of the Spray Gun Assembly 6 must be attached to the Handle of the Spray Gun Assembly To do so simply screw the Wand firmly onto the male threads of the Handle See Figure A HANDLE HOSE SPRAY GUN ASSY 6 NOZZLE ADJUSTMENT FIGURE A ao SKU 93302 For technical questions please call 1 800 444 3353 PAGE 5 12 AN A CAUTION Always wear eye breathing and skin protection Wear ANSI approved safety impact goggles an ANSI approved respirator latex gloves and proper safety clothing when using this product Prior to filling the Tank 1 of the Sprayer with liquid remove the Cap 2 and check to make sure the Filter 3 is clear of dirt and debris If necessary remove the Filter and thoroughly clean Next insert the Filter back into the opening of the Tank Fill t
5. he Tank with up to 4 gallons of liquid Then replace the Cap on the Tank See Assy Diagram NOTE The Sprayer is heavy when completely filled with liquid Always get assistance when strapping the Sprayer onto your body If necessary adjust the Strap Assembly 7 for comfort See Assy Diagram Always make sure other adults children and animals do not have access to the area s in which you intend to chemically treat Grip the Handle of the Spray Gun Assembly 6 firmly with your right hand See Assy Diagram With your left hand pump the Hand Pump Assembly 5 to build up sufficient pressure in the Sprayer system Once the system is pressurized as indicated by an increased tension on the Hand Pump Lever you may discontinue pumping the Hand Pump Assembly See Assy Diagram Point the Nozzle of the Spray Gun Assembly 6 toward the area to be sprayed Then squeeze the Trigger on the Spray Gun Assembly to begin spraying See Assy Diagram NOTE The Nozzle of the Spray Gun Assembly 6 may be adjusted for a pin point spray or a fan spray See Assy Diagram As you spray the system will begin to depressurize When the distance of the spray diminishes you will need to stop spraying momentarily Then resume pumping the Hand Pump Assembly 5 to re pressurize the system before spray ing again See Assy Diagram If it becomes necessary to refill the Tank 1 of the Sprayer continue squeezing the Trigger on the Spray
6. ing or broken please call Harbor Freight Tools at the number shown on the front cover of this manual as soon as possible GENERAL SAFETY RULES IMPORTANT SAFETY INSTRUCTIONS WARNING READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions detailed in this manual may result in serious personal injury SAVE THESE INSTRUCTIONS WORK AREA fi Keep your work area clean and well lit Cluttered and dark work areas invite accidents SKU 93302 For technical questions please call 1 800 444 3353 PAGE 2 11 Keep bystanders children and visitors away while operating the Sprayer Distractions can cause you to lose control PERSONAL SAFETY Stay alert Watch what you are doing and use common sense when operating a power tool Do not use the Sprayer while tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Dress properly Do not wear loose clothing or jewelry Contain long hair Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Do not overreach Keep proper footing and balance at all times Proper footing and balance enables better control of the Sprayer in unexpected situations Always wear eye breathing and skin protection Wear ANSI approved safety impact goggles an ANSI approved respirator latex gloves and proper safety cloth
7. ing when using this product TOOL USE AND CARE Do not force the Sprayer Use the correct product for your application The correct product will do the job better and safer at the rate for which it is designed Store idle tools and equipment out of reach of children and other untrained people Tools and equipment are dangerous in the hands of untrained users Maintain the Sprayer with care Keep this product clean A properly maintained tool is easier to control Do not use damaged tools and equipment Tag damaged tools and equipment Do not use until repaired Check for misalignment or binding of moving parts loose or broken parts and any other condition that may affect the Sprayer s operation If damaged have the Sprayer serviced before using Many accidents are caused by poorly maintained tools and equipment Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one product may become hazard ous when used on another product SKU 93302 For technical questions please call 1 800 444 3353 PAGE 3 12 Product service must be performed only by qualified service technician Service or maintenance performed by unqualified personnel could result in a risk of injury 13 When servicing the Sprayer use only identical replacement parts Follow instructions in the Inspection Maintenance And Cleaning section of this manual Use of unauthorized parts or failure to fo
8. llow maintenance instructions may create a risk of electric shock or injury SPECIFIC SAFETY RULES ly Maintain labels and nameplates on the Sprayer These carry important information If unreadable or missing contact Harbor Freight Tools for a replacement 2 Use the right product for the job There are certain applications for which this product was designed Do not use small tools equipment or attachments to do the work of larger industrial tools equipment or attachments Do not use this product for a purpose for which it was not intended ro Industrial applications must follow OSHA requirements 4 Store idle tools When not in use store the Sprayer in a clean dry safe location out of reach of children 5 Be careful when filling so as not to splash liquids into face or eyes Always wear ANSI approved safety goggles 6 This Sprayer is intended to be used only with water liquid fertilizers liquid herbicides and liquid pesticides Never attempt to spray flammable combustible or corrosive liquids with the Sprayer fa Always follow all chemical label precautions and local EPA regulations when using liquid chemicals Do not touch harmful chemicals After use clean the Sprayer thoroughly with agents recommended by the chemical manufacturer Always consider contents of the Sprayer to be poisonous due to contamination if previously used 8 Never point the nozzle of the Spray Gun Assembly at yourself or other people Alway
9. s be alert to the direction of the wind to insure contents of the Sprayer are not blown back at the operator Never spray if windy conditions are present 9 A note on Chemicals disposal Never attempt to burn unused fertilizers herbicides pesticides or any other types of chemicals Make sure to check with your local solid waste authorities for proper diposal procedures 10 Always make sure children and animals do not have access to chemically treated areas SKU 93302 For technical questions please call 1 800 444 3353 PAGE 4 11 Dry running will cause damage to the inner seals Make sure the water or liquid chemical supply used for the Sprayer is not dirty or sandy 12 Do not pull or carry the Sprayer by its Spray Gun Assembly Use the Handle on the Sprayer to move the tool from one location to another 13 The work area should have adequate drainage to reduce the possibility of a fall due to slippery surfaces 14 This product is designed for outdoor use only 15 Keep the Cap and Spray Gun Assembly of the Sprayer connected to the tool while the system is pressurized Prior to refilling or emptying the Tank squeeze the Trigger on the Spray Gun Assembly to completely depressurize the system 16 Prior to starting the Sprayer in cold weather check all of the parts of the tool to make sure ice has not formed Do not store the Sprayer where the temperature will fall below 32 Fahrenheit 17 Do not keep water or any liquid chemi
10. ve z J ORE ni St GARDENSJ 4 GALLON SPRAYER ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements actual product may differ slightly from the product described herein Distributed Exclusively by HARBOR FREIGHT H Ls TOOLS miii 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE Copyright 2005 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions please call 1 800 444 3353 PRODUCT SPECIFICATIONS Pp oitem ST Description O Tank Capacity 4 Gallons Product Compatibility For use with Water Liquid Fertilizers Herbicides and Pesticides only Pump Type Manual Hand Operated Piston Pump SAVE THIS MANUAL You will need this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures parts list and assembly diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep this manual and invoice in a safe and dry place for future reference GENERAL SAFETY RULES When unpacking check to make sure all the parts shown in the Parts List on page 9 are included If any parts are miss
Download Pdf Manuals
Related Search