Harbor Freight Tools 6852 User's Manual
Contents
1. CAUTION Before each use inspect the condition of the Sanding Belt 2 Look for tearing excessive wear or other damage to the Sanding Belt Never use a Sanding Belt that is damaged When replacing never use an inexpensive low quality Sanding Belt 2 Plug the Power Cord 55 into a grounded 110 Volt electrical outlet See Figure B 3 Turn the Power Switch 53 to its ON position and allow the Sanding Belt 2 to come to full speed for approximately ten seconds before feeding the workpiece into the Sanding Belt See Figure B 4 Hold the workpiece firmly with both hands and carefully set it flat and level upon the Sanding Belt 2 and against the Back Stop 39 See Figure B 5 Apply moderate downward pressure on the workpiece allowing the Sanding Belt 2 to cut without being forced 6 Once the sanding procedure is completed remove the workpiece from the Sand ing Belt 2 turn the Power Switch 53 to its OFF position and unplug the Power Cord 55 from its electrical outlet See Figure B REV 04b SKU 06852 For technical questions please call 1 800 444 3353 PAGE 14 To Perform Horizontal Sanding With The Sanding Disc 1 CAUTION Before each use inspect the condition of the Sanding Disc 15 Look for tearing excessive wear or other damage to the Sanding Disc Never use a Sanding Disc that is damaged When replacing never use an inexpensive low quality Sanding Disc NOTE The Sanding Dis2. THE CORRECT GAUGE AND LENGTH This product requires a 14 gauge extension cord REDUCE THE RISK OF ACCIDENTAL STARTING Make sure the Power Switch 53 is in the OFF position before plugging the Power Cord 55 into a grounded 3 hole 110 Volt electrical outlet See Figure B and Assy Diagram PRIOR TO STARTING THE BELT DISC SANDER MAKE SURE ALL ADJUST ING KEYS AND WRENCHES ARE REMOVED FROM THE TOOL BEFORE SANDING TURN ON THE BELT DISC SANDER AND CHECK FOR EXCESSIVELY LOOSE SANDING BELT DISC 2 15 OR MACHINE VIBRA TION If this is found turn off the tool and correct the problem before using ALWAYS KEEP HANDS AND FINGERS AS FAR AWAY AS POSSIBLE FROM THE MOVING PARTS OF THE BELT DISC SANDER SKU 06852 For technical questions please call 1 800 444 3353 PAGE 4 10 11 12 13 14 15 16 17 ALLOW THE SANDING BELT DISC 2 15 TO TURN UP TO FULL SPEED BEFORE FEEDING A WORKPIECE INTO THE SANDING BELT DISC When turning off the Belt Disc Sander allow the Sanding Belt Disc to slow down and stop on its own Do not press against the Sanding Belt Disc to stop it FEED THE WORKPIECE INTO THE SANDING BELT DISC 2 15 GRADU ALLY Do not force the machine to remove material faster than it was designed to cut TO AVOID PERSONAL INJURY AND OR DAMAGE TO THE MACHINE ALWAYS ALLOW APPROXIMATELY 1 16 CLEARANCE BETWEEN THE SANDING BELT 2 AND THE BACK STOP 39 ALWAYS ALLOW APPROXIMATELY 1 16 CLEARAN
3. a period of ninety days from date of purchase that the engine motor the belts if so equipped and the blades if so equipped are free of defects in materials and workmanship Harbor Freight Tools also warrants to the original purchaser for a period of one year from date of purchase that all other parts and components of the product are free from defects in ma terials and workmanship 90 days if used by a professional contractor or if used as rental equipment This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the com plaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund th
4. are factors which cannot be built into this product but must be supplied by the operator SKU 06852 For technical questions please call 1 800 444 3353 PAGE 3 SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS MAINTAIN A SAFE WORKING ENVIRONMENT Keep the work area well lit Make sure there is adequate surrounding workspace Always keep the work area free of obstructions sawdust grease oil trash and other debris Do not use the Belt Disc Sander in areas near flammable chemicals dusts and vapors Do not use the Belt Disc Sander in a damp or wet location GROUND THIS PRODUCT The electrical Power Cord 55 for this product is equipped with a grounded 3 Prong Plug Never remove the grounding prong or modify the Plug in any way Do not use adapter plugs with this product To com ply with the National Electric Code and to provide additional protection from the risk of electrical shock this product should only be connected to a 110 Volt 3 hole electrical outlet that is protected by a Ground Fault Circuit Interrupter GFCI DO NOT ABUSE THE POWER CORD Do not use the Power Cord 55 to pull its 3 Prong Plug from an electrical power outlet Keep the Power Cord away from heat oil sharp edges and moving parts Route the Power Cord safely Do not route the Power Cord where it can be walked on or tripped over Replace a dam aged Power Cord immediately IF AN EXTENSION CORD not included IS USED MAKE SURE TO USE ONLY UL APPROVED CORDS HAVING
5. tighten the tension on the Sanding Belt See Figure H Retighten the two Lock Knobs 44 and lock the two Adjust Nuts 44 in place See Figure H Plug the Power Cord 55 into a 110 volt electrical outlet and turn the Power Switch 53 to its ON position See Figure B Allow sufficient time for the Sanding Belt 2 to turn at full speed See Figure H NOTE If the Sanding Belt 2 appears to be too loose on the Sand Belt Frame 40 REV 04b SKU 06852 For technical questions please call 1 800 444 3353 PAGE 10 turn off the machine and unplug it from its electrical outlet Then repeat Steps 2 through 7 to further increase the tension on the Sanding Belt See Figures B and H 9 Attach the Back Stop 39 to the side of the Sanding Belt Frame 40 as shown in Figure H BACK STOP 39 Sand in this area LOCK KNOB amp F LOCK KNOB amp ADJUST NUT ASSY ADJUST NUT ASSY 44 44 SANDING BELTFRAME LOCK SANDING BELT 2 Ee K 40 KNOB 44 ADJUST NUT 44 FIGURE H To Install A Sanding Disc oa ae 1 CAUTION Always turn the Power Switch 53 SANDING DISC PLATE to its OFF position 16 and unplug the Power Cord 55 from its 110 volt electrical outlet before performing this procedure See Figure B 2 Swing the Table Support Bracket 9 out of the way and FIGURE I remove the cover from the Pulley Cover 22 as explained on page 9 Check to make sure the Sand
6. 0 444 3353 PAGE 5 18 WARNING People with pacemakers should consult their physician s before using this product Operation of electrical equipment in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker UNPACKING When unpacking check to make sure all the parts shown on the Parts List on page 16 are included If any parts are missing or broken please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible PRODUCT FEATURES NOTE Prior to assembling and operating the Belt Disc Sander it is important to fa miliarize yourself with all of the machine s major components Failure to do so may result in personal injury and or damage to the machine and workpiece being sanded See Figure B and refer to the Operating Instructions section in this manual 9 SANDING DISC MITER GAUGE 3 LOCK KNOB AD T NUT ASSY 44 3 BACK STOR OB ADJUST NUT ASSY 44 6 SANDING BELT 2 PULLEY SN COVER if ho 22 7 SAND BELT ee BASE n 1 FRAME 40 51 POWER SWITCH 53 STAND 56 SKU 06852 For technical questions please call 1 800 444 3353 PAGE 6 ASSEMBLY INSTRUCTIONS NOTE For additional references to the parts listed below refer to the Assembly Diagram on page 17 To Assemble The Stands Frames And Upper Bracket 1 With assistance position the two Stands 56 upright on the floor and parallel to one another See Figur
7. CATIONS MUST FOLLOW OSHA REQUIREMENTS STAY ALERT Watch what you are doing at all times Use common sense Do not use this product when you are tired or distracted from the job at hand CHECK FOR DAMAGED PARTS Before using this product carefully check that it will operate properly and perform its intended function Check for damaged parts and any other conditions that may affect the operation of this product Re place or repair damaged or worn parts immediately REPLACEMENT PARTS AND ACCESSORIES When servicing use only identi cal replacement parts Only use accessories intended for use with this product Approved accessories are available from Harbor Freight Tools MAINTAIN THIS PRODUCT WITH CARE Keep this product clean and dry for better and safer performance MAINTENANCE For your safety service and maintenance should be performed regularly by a qualified technician USE THE RIGHT TOOL FOR THE JOB Do not attempt to force a small tool or attachment to do the work of a larger industrial tool There are certain applica tions for which this tool was designed It will do the job better and more safely at the rate for which it was intended Do not modify this tool and do not use this tool for a purpose for which it was not intended WARNING The warnings precautions and instructions discussed in this manual cannot cover all possible conditions and situations that may occur The operator must understand that common sense and caution
8. CE BETWEEN THE SANDING DISC 15 AND THE TABLE 1 WHEN SANDING A LARGE WORKPIECE MAKE SURE ITS ENTIRE LENGTH IS PROPERLY SUPPORTED If necessary use a roller stand not included with a larger workpiece NEVER ATTEMPT TO REMOVE MATERIAL STUCK IN THE MOVING PARTS OF THE BELT DISC SANDER WHILE IT IS PLUGGED IN AND RUNNING NEVER STAND ON THE BELT DISC SANDER Serious injury could result if the Belt Disc Sander is tipped or if the turning Sanding Belt Disc 2 15 are acciden tally contacted ALWAYS TURN THE POWER SWITCH 53 TO ITS OFF POSITION AND UN PLUG THE BELT DISC SANDER FROM ITS ELECTRICAL SUPPLY SOURCE BEFORE PERFORMING ANY INSPECTION ADJUSTMENTS MAINTE NANCE OR CLEANING PROCEDURES WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contain chemicals known to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are lead from lead based paints and arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemi cals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles California Health amp Safety Code 25249 5 et seq SKU 06852 For technical questions please call 1 80
9. L CENTRAL MACHINERY 6 BELT amp 9 SANDER ASSEMBLY AND OPERATING INSTRUCTIONS Visit our website at http Awww harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2004 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included For technical questions or replacement parts please call 1 800 444 3353 Revised Manual 09k PRODUCT SPECIFICATIONS Electrical Requirements 1 HP Ball Bearing Motor 110 Volt 60 Hz 12 8 Amps 3450 Rom oe Table Surface Dimensions 6 1 2 x 12 3 4 Table Tilt 0 50 Degrees Work Table Options For Sanding Disc or Sanding Belt Use 6 x 48 9 Diameter PSA Type Belt Speed 1280 FPM SAVE THIS MANUAL You will need this manual for the safety warnings and precautions assembly op erating inspection maintenance and cleaning procedures parts list and assem bly diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep this manual and invoice in a safe and dry place for future
10. Replace cover of the Pulley Cover 22 and tighten the 4 screws Verify that the pulley cover does not contact the Sanding Disc 15 If it does you need to adjust the Sanding Disc Plate 16 NOTE When positioning the Table 1 make sure there is more than clearance but 12 less than clearance between the Table and the Sanding Disc 15 Insert the round end of the Support Bar 18 into the hole on the side of the Base 18 See Figure G Put the Table Support Bracket 9 over the end of the Support Bar with the tapered side of the Bracket facing the Sanding Disc 15 and also the flat side of the Bar lined up with the Set Screw Tighten the Set Screw 14 on the Table Support Bracket Set the Table Support Bracket as shown in Figure J page 12 Tighten the two Set Screws 14 on the side of the Base to secure the bar OPERATING INSTRUCTIONS To Install A Sanding Belt 1 CAUTION Always turn the Power Switch 53 to its OFF position and unplug the Power Cord 55 from its 110 volt electrical outlet before performing this procedure See Figure B Loosen the two Lock Knobs 44 in order to unlock the two Adjust Nuts 44 See Figure H next page Turn the two Adjust Nuts 44 counterclockwise to allow the Sanding Belt 2 to be inserted onto the Sand Belt Frame 40 See Figure H Slide the Sanding Belt 2 fully and evenly onto the Sanding Belt Frame 40 Then turn the two Adjust Nuts clockwise to
11. c 15 is typically used for smaller workpieces Plug the Power Cord 55 into a grounded 110 Volt electrical outlet See Figure B Turn the Power Switch 53 to its ON position and allow the Sanding Disc 15 to come to full speed for approximately ten seconds before feeding the work piece into the Sanding Disc See Figure B Hold the workpiece firmly with both hands and carefully set it flat and level upon the Table 1 See Figure B Apply moderate inward pressure on the workpiece allowing the Sanding Disc 15 to cut without being forced Once the sanding procedure is completed remove the workpiece from the Sand ing Disc 15 turn the Power Switch 53 to its OFF position and unplug the Power Cord 55 from its electrical outlet See Figure B To Perform Vertical Sanding With The Sanding Belt 1 Adjust the Sand Belt Frame 40 and Table 1 for a vertical sanding procedure See Figures L and M Plug the Power Cord 55 into a grounded 110 Volt electrical outlet See Figure B Turn the Power Switch 53 to its ON position and allow the Sanding Belt 2 to come to full speed for approximately ten seconds before feeding the workpiece into the Sanding Belt See Figure M Hold the workpiece firmly with both hands and carefully set it flat and level upon the Table 1 See Figure M Apply moderate inward pressure on the workpiece allowing the Sanding Belt 2 to cut without bein
12. e C 2 Place the end of one Frame 64 on the inside edge of one Stand 56 and align the two mounting holes on the end of the Frame with the two lower mounting holes on the Stand See Figure C 3 Secure the Frame 64 to the Stand 56 using two Bolts 58 two Washers 60 and two Nuts 63 See Figure C 4 Repeat Steps 1 2 and 3 to connect the other end of the Frame to the re maining Stand See Figure C 5 To connect the remaining Frame 64 to the two Stands 56 follow Steps 1 2 3 and 4 See Figure C BOLT 58 WASHER 60 f mostly hid NUT 63 den BOLT 58 WASHER 60 NUT 63 FIGURE C 6 Place both Upper Brackets 57 on the top edges of the two Stands 56 and align the eight mounting holes two on each end of the Brackets with the eight mounting holes two on each end of the Stands See Figure C 7 Secure both Upper Brackets 57 to the two Stands 56 using eight Bolts 58 Washers 60 and Nuts 63 See Figure C REV 05b SKU 06852 For technical questions please call 1 800 444 3353 PAGE 7 8 With assistance carefully tip the assembled Stand on its side Attach a Rubber Foot 59 to each of the Stand s four corners using four Rubber Feet four Wash ers 60 and four Screws 61 Then place the Stand back in its upright position See Figure D To Attach The Base To The Upper Bracket 1 With assistance place the Base 51 of the Belt Disc Sander
13. e Figure K REV 04b SKU 06852 For technical questions please call 1 800 444 3353 PAGE 12 MITER GAUGE 3 MITER GAUGE KNOB ANGLE SCALE FIGURE K To Adjust The Sand Belt Frame For Vertical Sanding Loosen the two Nuts 86 on the Sanding Belt Frame 40 and with assistance raise the Sanding Belt Frame to its full vertical position Then firmly retighten the two Nuts to lock the Sanding Belt Frame in place See Figure L NUT 36 SANDING BELT FRAME 40 VERTICAL POSITION FIGURE L To Adjust The Position Of The Table 1 When the Sanding Belt Frame 40 is in its vertical position the Table 1 should be repositioned to the front of the Sanding Belt Frame See Figure M next page 2 To reposition the Table 1 loosen the two Set Screws 14 and remove the Table including the Support Bar 18 See Figure M 3 Insert the Support Bar into the Mounting Hole and tighten the other two Set Screws 14 See Figure M REV 04b SKU 06852 For technical questions please call 1 800 444 3353 PAGE 13 4 NOTE When repositioning the Table 1 SANDING BELT FRAME 40 make sure there is more than clearance but less than clearance be tween the Table and the Sand ing Belt Frame 40 See Fig ure M END VIEW TABLE 1 SANDING SUPPORT BAR 18 SET SCREW 14 BAR 18 FIGURE M SET SCREW 14 To Perform Horizontal Sanding With The Sanding Belt 1
14. e purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 SKU 06852 For technical questions please call 1 800 444 3353 PAGE 19
15. g forced See Figure M REV 04b SKU 06852 For technical questions please call 1 800 444 3353 PAGE 15 6 Once the sanding procedure is completed remove the workpiece from the Sand ing Belt 2 turn the Power Switch 53 to its OFF position and unplug the Power Cord 55 from its electrical outlet See Figure B INSPECTION MAINTENANCE AND CLEANING 1 CAUTION Always turn the Power Switch 53 to its OFF position and un plug the Power Cord 55 from its 110 volt electrical outlet before perform ing any inspection adjustments maintenance or cleaning 2 BEFORE EACH USE inspect the general condition of the Belt Disc Sander Check for loose screws misalignment or binding of moving parts cracked or broken parts damaged electrical wiring excessively loose Sanding Belt 2 and Sanding Disc 15 and any other condition that may affect its safe operation If abnormal noise or vibration occurs have the problem corrected before further use Do not use damaged equipment 3 DAILY Sanding Belts 2 and Sanding Discs 15 must be sharp and clean to perform properly Depending on materials sanded and frequency of tool use Sanding Belts and Sanding Discs become clogged with wood particles and dull Dull Sanding Belts and Sanding Discs rub the workpiece rather than cut which results in increased friction higher temperatures and a burned workpiece As often as possible check the condition of the Sanding Belt and Sandi
16. ing Disc Plate 16 is free of dirt oil and other debris See Figure l 3 Remove the paper backing on the adhesive Sanding Disc 15 and stick the Sanding Disc firmly and evenly onto the Sanding Disc Plate 16 Restore the Table Support Bracket and Pulley Cover to their original positions See Figure l REV 04b SKU 06852 For technical questions please call 1 800 444 3353 PAGE 11 To Adjust The Angle Of The Table 1 The angle of the Table 1 may be adjusted from 0 to 45 Degrees See Figure J 2 To adjust the angle of the Table 1 slightly loosen the Knob 10 See Figure J 3 Observe the Angle Gauge 5 Then raise or lower the Table until the desired angle of the Table is shown on the Angle Gauge See Figure J 4 Once the desired angle of the Table 1 is obtained retighten the Knob 10 See Figure J TABLE 1 TABLE 1 FIGURE J To Adjust The Angle Of The Miter Gauge 1 The angle of the Miter Gauge 3 may be adjusted to the right 0 to 45 Degrees and to the left 0 to 45 Degrees See Figure K next page 2 To adjust the angle of the Miter Gauge 3 slightly loosen the Miter Gauge Knob See Figure K 3 Observe the Angle Scale on the Miter Gauge 3 Then move the Miter Gauge Body to the right or left until the desired angle of the Miter Gauge is shown on the Angle Scale See Figure K 4 Once the desired angle of the Miter Gauge 3 is obtained retighten the Miter Gauge Knob Se
17. ng Disc and if necessary replace a worn Sanding Belt and Sanding Disc with a new 6 wide by 48 Sanding Belt and 9 diameter Sanding Disc 4 DAILY With a soft brush cloth or vacuum remove all sawdust and debris from the Belt Disc Sander Then use a premium quality lightweight machine oil to lubricate all moving parts PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTI FIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 06852 For technical questions please call 1 800 444 3353 PAGE 16 PARTS LIST PART DESCRIPTION QTY DESCRIPTION Table Sanding Belt Miter Gauge Screw M5x30 Angle Gauge Washer 8 Screw M8x12 Nut M5 Table Support Bracket Knob Screw M5x10 Pointer s Set Screw Driving Roller Nut M8 B5x50 Key Dri
18. on top of the Upper Brackets 57 Align the four threaded mounting holes on the Base with the four mounting holes on the Upper Brackets See Figures B and D 2 From underneath the Stand secure the Base 51 to the Upper Brackets 57 by inserting four Screws 66 with four Washers 65 upward through the Stand s four mounting holes Then firmly tighten the four Screws into the four threaded mounting holes on the Base See Figure D SCREW 66 i SCREW 66 WASHER 65 WASHER 65 SCREW 66 i SCREW 66 WASHER 65 7 WASHER 65 SCREW WASHER RUBBER 61 60 FOOT FIGURE D 59 REV04h 05b SKU 06852 For technical questions please call 1 800 444 3353 PAGE 8 To Assemble The Pulleys Sanding Disc Plate and Table 1 Remove the 4 screws from the cover on the Pulley Cover 22 and set aside 2 Line up the three bolt holes on the Pulley Cover 22 with the threaded holes in the Bracket 4 26 Place a Washer 21 over each of 3 Screws 20 Insert a Screw 20 into each hole and tighten See Figure E FIGURE E Screw 20 3 This item is packed with tape on the shafts ca to keep the keys in place Remove the tape from the upper shaft being careful to not lose the key 4 Loosen the Set Screw 14 on the Large Pulley 19 Put the Large Pulley on the upper shaft with the smaller step on the pulley inside and with the key lined up with the slot on the Pulley Be sure the key stays in
19. reference GENERAL SAFETY WARNINGS AND PRECAUTIONS KEEP WORK AREA CLEAN AND DRY Cluttered damp or wet work areas invite injuries KEEP CHILDREN AWAY FROM WORK AREA Do not allow children to handle this product STORE IDLE EQUIPMENT When not in use tools and equipment should be stored in a dry location to inhibit rust Always lock up tools and equipment and keep out of reach of children DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS Read warning labels on prescriptions to determine if your judgement or reflexes are impaired while taking drugs If there is any doubt do not attempt to use this product REV 07g SKU 06852 For technical questions please call 1 800 444 3353 PAGE 2 10 11 12 13 14 15 USE EYE BREATHING AND HAND PROTECTION Wear ANSI approved safe ty impact eyeglasses safety impact full face shield and a dust mask or respirator when using this product ANSI approved safety impact eyeglasses safety impact full face shield dust masks and respirators are available from Harbor Freight Tools DRESS SAFELY Do not wear loose clothing or jewelry as they can become caught in moving parts Wear a protective hair covering to prevent long hair from becoming caught in moving parts If wearing a long sleeve shirt roll sleeves up above elbows DO NOT OVERREACH Keep proper footing and balance at all times to prevent tripping falling back injury etcetera INDUSTRIAL APPLI
20. the correct position all the way through the pulley 5 Repeat steps 3 and 4 putting the Small Pulley 52 on the lower shaft See Figure F 6 Carefully align both pulleys and tighten Use a flat head screwdriver through the slot in the Pulley Cover 22 to tighten the Set Screw 14 on the Large Pulley 19 See Figure G Use a hex key not included to tighten the Set Screw 14 on the Small Pulley 52 T Loosen the 4 Screws 48 that hold the Motor 30 just enough to let the Motor move Move the Motor towards the Large Pulley enough to let the Belt 17 slip on over both Pulleys Move the Motor away from the Large Pulley until the Belt is tight enough so that if pushed it doesn t move more than Hold the Motor in place while you retighten the 4 Screws 48 Large Pul 2 S FIGURE F J vy Ww d NA 8 Put the Sanding Disc Plate 16 on the end of the shaft so that it s flush with the end of the shaft Tighten its set screw once again using the slot in the Pulley Cover amp Small Pul 22 See Figure G ley 52 i 9 Check to make sure the Sanding Disc Plate 16 is free i of dirt oil and other debris REV 04b SKU 06852 For technical questions please call 1 800 444 3353 PAGE 9 10 Remove the paper backing on the adhesive Sanding Disc 15 and stick the Sanding Disc firmly and evenly onto the Sanding Disc Plate 16 See Figure I page 11
21. ving Roller Shaft Back Stop Sanding Belt Frame Roller Adjust Bar Spring Pin 5 10 11 12 13 14 Set Screw 15 Sanding Disc 16 17 18 19 Large Pulley 20 Screw M8x10 21 Washer 8 22 Pulley Cover 3 Screw M8x35 24 Washer 4 25 Knob 26 Bracket 27 28 29 30 Motor 31 Screw M8x25 32 Key B5x20 33 Tube Leader Roller Lock Knob Adjust Nut Assy Spring Leader Roller Shaft Set Screw Support Bolt M16x240 Screw M8x30 Nut M8x30 60 Sanding Disc Plate V Belt A 710 Support Bar Cord Clamp Base Small Pulley Switch Cord Clamp Power Cord NO Stand Upper Bracket Bolt M8x10 Rubber Foot Washer 8 8 Retaining Ring C Snap Ring Screw M5x12 Nut Nut Frame Washer 66 Screw M8x10 Ball Bearing M5 M8 NOTE Some parts are listed and shown for illustration purposes only and are not avail able individually as replacement parts SKU 06852 For technical questions please call 1 800 444 3353 REV 05b PAGE 17 ASSEMBLY DIAGRAM NOTE Some parts are listed and shown for illustration purposes only and are not avail able individually as replacement parts REV 05b SKU 06852 For technical questions please call 1 800 444 3353 PAGE 18 LIMITED 1 YEAR 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that for
Download Pdf Manuals
Related Search