Harbor Freight Tools 60 LED Solar Security Light Product manual
Contents
1. NOILVHJdO Motion Detector Control Knobs cont SENS Sensitivity Adjust Sensitivity To sense small or large moving objects The SENS Adjusting Knob 10 sets the level of sensitivity of the Motion Detector Head The Motion Detector Head is most sensitive to movement across the detection zone rather than movement toward or away from the Motion Detector Head 6 Movement is best detected at a distance of 40 feet or less Note Turn the dial anywhere between the minimum and maximum settings to adjust the level of sensitivity as needed Sensitivity is affected by the ambient air temperature If it is hot outside the sensor has difficulty detecting changes in heat In cold temperatures the sensitivity is increased and may need to be adjusted Minimum Position Turn the dial counterclockwise to the minimum setting Ideal for cold winter conditions or when nuisance tripping is a problem If the light is activated ALA by small animals or rapid changes in heat the sensitivity can be reduced by turning the knob counterclockwise towards the minimum setting Maximum Position Turn the dial clockwise to the maximum setting Ideal for hot summer conditions or to maximize range Testing the Light After the battery is charged and the control Knobs are set walk slowly around the detection area The sensor detects infrared radiation given off by a person or animal This triggers the Light t2. Motion Detector Head detecting movement Battery pack not fully charged Keep solar panel clean Allow to charge in full sunlight for 3 days with the Power Switch OFF Light flashes With Switch set to OFF allow to charge in full on and off with sunlight for 3 days before further use clicking sounds Turn TIME knob counterclockwise to reduce the time the light stays on Check sensing area for possible heat sources such detected as air vents vehicles or objects in wind Reposition the Motion Detector Head if needed or turn SENS Knob counterclockwise to lower sensitivity Power Switch set to ON Turn Power Switch to AUTO Light turns ON Changes in heat are being Check sensing area for possible heat sources and OFF detected from a fixed heat such as air vents vehicles or objects in wind source or moving object Reposition the Motion Detector Head Sudden temperature change Turn Power Switch OFF until storm passes due to storms or high winds Mount in a sheltered location MAINTENANCE Follow all safety precautions whenever diagnosing or servicing the tool Disconnect Battery Pack and Charger power supply before service Item 69643 For technical questions please call 1 800 444 3353 Page 9 AONVNALNIVIN Parts List and Diagram PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NE
3. of the Lamp has three settings OFF Center position Motion Detector Control Knobs The Solar Powered Security Light has 3 different Control Knobs on the underside of the Motion Detector Head They control the Motion Detector Head s sensor They are sensitivity to light LUX the light s duration TIME and the sensor s sensitivity to motion SENS NOTE After each adjustment walk the detection area to check the adjustment just made Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product CAUTION The UNIT WILL NOT FUNCTION UNLESS The Solar Panel is first charged for 3 DAYS OF FULL SUN with the SENSOR POWER OFF ON Towards the Lamp The lamp stays on functioning as a normal light AUTO Away from the Lamp The light will turn on automatically when motion is detected by the Motion Sensor Head SENS TIME Adjusting Knob LUX Adjusting Adjusting Knob Knob SENS TIME Fi S Underside of Motion Detector Head Page 6 For technical questions please call 1 800 444 3353 Item 69643 Motion Detector Control Knobs cont LUX Light Level Adjust Light Level When light will go ON The LUX Adjusting Knob 9 tells the sensor the level of darkness that must be reached before the Light turns on Minimum Position Turning the dial counterclockwise to the minimum settin
4. scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state Bunker Hill Security 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353
5. ITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Parts List Part Description Qty 3 Mounting Screw 6 4 LED Battery Housing 1 Battery Housing 6 Motion Detector Head za Mounting Plate Record Product s Serial Number Here Part ___ Description Qty 8 Power Switch _ 1 9 Battery Housing Outlet 1 Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Page 10 For technical questions please call 1 800 444 3353 Item 69643 Assembly Diagram Underside of Motion Detector Head 6 MAINTENANCE Item 69643 For technical questions please call 1 800 444 3353 Page 11 Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its produc
6. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference Bunker Hill Security ITEM 69643 60 LED Solar Security Light b3 SS gS 6 s Visit our website at http www harborfreight com Email our technical support at tech harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 800 444 3353 as soon as possible Copyright 2012 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included ALAAVS Table of Contents Safely sssesariersteseti eavisstiniesdsinenesihen qessienead 2 MaINtGNANCE i iscicssteteecees c
7. de beeavcete anecdsdeenens 9 SPECIHICATIONS esiri irina 4 Parts List and Diagram e 10 SOLU P mataria iesu i say aE aa 4 WarrANty innana nnii 12 Operation cecceceeeeeeceeeeeeeeeeeeeeteenensaeees 6 Bunker Hill Security WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER Indicates a hazardous situation which if not avoided will result in death or serious injury AWARN NG Indicates a hazardous situation which if not avoided could result in death or serious injury Indicates a hazardous situation which if not avoided ACAUTION could result in minor or moderate injury NOTICE CAUTION IMPORTANT SAFETY INFORMATION AWARNING Read all safety warnings and instructions Failure to follow the warnings and instructions may result in electric shock fire and or serious injury Save all warnings and instructions for future reference Addresses practices not related to personal injury 1 Keep installation area clean Cluttered 4 Replacement parts and accessories When areas invite accidents servicing use only identical replacement parts Use of any other parts will void the warranty 2 Observe installation area conditions Keep work area well lit during installation 5 Check hardware and assembled parts after assembling All connections sh
8. g lowers the sensor level The sensor will only trigger the light to turn on at dusk or when it is dark out This is the ideal position for general evening and night operation Maximum Position Turning the dial clockwise to the maximum setting increases the sensor level The light will go on in most situations ranging from dark to daylight Note If the Security Light is not operating at night due to interference from a street light or other interference turn the LUX knob towards the maximum setting Bl Adjust the dial as needed between the minimum and maximum settings to achieve the desired level of sensitivity TIME Light Duration Adjust Time How long light stays ON The TIME Adjusting Knob 11 sets how long the Light stays lit after motion is no longer detected by the sensor The TIME is adjustable from 5 seconds to 2 minutes Item 69643 Minimum Position Turn the dial counterclockwise to the minimum for the light to stay on for 5 seconds after motion is no longer detected Y Mid Range Adjusting the dial between the Minimum and Maximum to choose any time between 5 seconds and 2 minutes for the light to stay on after motion is no longer detected Maximum Position Turn the dial clockwise to the maximum for the light to stay on for 2 minutes after motion is no longer detected Z Q lt aa Lu ou O oS For technical questions please call 1 800 444 3353 Page 7
9. nsert the plastic Anchors then secure the 5 Loosen the Detector Angle Lock swivel Solar Panel in place with the screws the Motion Detector Head so that it faces the area where movement will occur and tighten the Detector Angle Lock Carefully route the Power Cord of the Solar Panel to the Lamp and plug it into the Battery Housing Outlet on the back of the Battery Housing Page 4 For technical questions please call 1 800 444 3353 Item 69643 Functions Solar Panel Y Mounting Bracket 2 g S amp e ora Battery Housing Battery Housing Outlet _ _ __ On bottom of Battery Housing Power Switch 2 On bottom of Battery Housing I I 1 Detector Angle Lock i I Motion Detector Head i On side of Motion Solar Panel Cable i Detector Head Motion Detector Controls On bottom of Motion Detector Head Figure A Item 69643 For technical questions please call 1 800 444 3353 Page 5 NOILVasAdO Operating Instructions A Initial Battery Charging Before the Security Light can operate properly the batteries need to be fully charged To charge the batteries 1 Turn OFF the Power Switch 2 ALLOW 3 DAYS OF FULL SUNLIGHT to fully charge the batteries 3 After charging turn the Power Switch Auto The light will illuminate for a short time when first switched on This indicates that it is working properly Power Switch The Power Switch located under the Battery Housing
10. o turn on The Light should go on in the area that you set up the Security Light to monitor Adjust the Knobs and sensor and re test until the unit functions as desired Repeat the test procedure as needed when there are weather and or temperature changes Bunker Hill Security Page 8 For technical questions please call 1 800 444 3353 Item 69643 Maintenance and Servicing AWARNING TO PREVENT SERIOUS INJURY FROM TOOL FAILURE Do not use damaged equipment If abnormal noise or vibration occurs have the problem corrected before further use Procedures not specifically explained in this manual must be performed only by a qualified technician Cleaning Maintenance and Lubrication 1 BEFORE EACH USE inspect the general 2 AFTER USE wipe external surfaces condition of the tool Check for of the tool with clean cloth leaking swollen or cracked battery pack 3 NiCd BATTERY MUST BE RECYCLED loose hardware OR DISPOSED OF PROPERLY Do not misalignment or binding of parts short incinerate or open battery e cracked or broken parts and e any other condition that may affect its safe operation Troubleshooting Possible Causes Likely Solutions Light won t Power is not on Check that Power Switch is set to ON or AUTO turn on Cable connection is loose Plug in firmly at back of Battery Housing LUX control is set Turn LUX knob towards Ba too close to K Motion sensor not Adjust angle and direction of
11. ould 3 Check for damaged parts Before using be tight and hardware tightened any product any part that appears damaged should be carefully checked to determine that 6 Keep children away Mount the Light Solar it will operate properly and perform its intended Panel and Cord out of children s reach function Check for any broken or damaged parts and any other conditions that may affect its operation Replace or repair damaged or worn parts immediately Do not use the Security Light if any switch does not turn on and off properly Page 2 For technical questions please call 1 800 444 3353 Item 69643 10 11 Dress properly Protective electrically non 12 NiCd BATTERY MUST BE RECYCLED conductive clothes and nonskid footwear are OR DISPOSED OF PROPERLY Do not recommended when working with the Solar short incinerate or open battery Powered Security Light Wear restrictive hair covering to contain long hair 13 Have your power tool serviced by a qualified repair person using only identical Use eye protection Wear ANSI approved impact replacement parts This will ensure that the safety goggles when setting up this product safety of the power tool is maintained Maintain products with care Keep the Solar 14 WARNING Handling the cord on this product s Powered Security Light clean for better and safer Charger will expose you to lead a chemical performance Inspect the Light periodically If known to the State of California
12. therein before set up or use of this product Note For additional information regarding the parts listed in the following pages refer to Parts List and Diagram on page 10 Installation 1 Decide where you want to place the Lamp and the 3 Mount the Lamp Solar Panel The Solar Panel is equipped with a 16 ft connecting wire so the Lamp and Solar Panel can be installed up to 16 ft apart The Solar Panel must be set in a location that receives full direct sunlight a minimum of eight hours a day Ideally the solar panel should be angled slightly toward the south northern hemisphere a Locate the unit six to eight feet above ground on a solid surface capable of supporting the Lamp and secure enough so that it will not move when exposed to vibrations or wind The unit must be high enough to allow for motion detection and light distribution b Mark the hole locations of the Mounting 2 Mount the Solar Panel Bracket then set the Lamp aside a Place the Solar Panel in the desired location c Check that the marked areas are clear of adjusting the unit to best fit the surface obstacles such as cables and electrical b Mark the hole locations of the Base lines Drill holes for the enclosed Screws then set the Solar Panel aside d Secure the Lamp in place with the screws c Check that the marked areas are clear of 4 obstacles such as cables and electrical lines Drill holes for the enclosed Screws and plastic Anchors d I
13. to cause cancer damaged have it repaired by a qualified technician and birth defects or other reproductive harm Wash hands after handling Do not overreach Keep proper footing and balance at all times If a ladder is to be used during California Health amp Safety Code 25249 5 et seq installation it should be supported by an assistant 15 The warnings precautions and instructions discussed in this instruction manual cannot Do not set up the Solar Powered Security Light cover all possible conditions and situations if under the influence of alcohol or drugs Read that may occur It must be understood by the warning labels on prescriptions to determine if your operator that common sense and caution are judgement or reflexes are impaired while taking factors which cannot be built into this product drugs If there is any doubt do not set up the Light but must be supplied by the operator A SAVE THESE INSTRUCTIONS Bunker Hill Security Item 69643 For technical questions please call 1 800 444 3353 Page 3 SAFETY dNLas Specifications Lamp 60 Super Bright White LEDs Battery Pack 6V 900mAh NiCd Battery Pack Solar Panel 6 1 4 x 5 Amorphous Solar Panel Detects Motion Up to 50 Range of Motion Up to 120 Delay Time 5 to 120 Seconds adjustable Setup Before Use Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings
14. ts meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the
Download Pdf Manuals
Related Search