Harbor Freight Tools 45333 User's Manual
Contents
1. Keep work area clean Cluttered areas invite injuries Observe work area conditions Don t expose to rain Keep work area well lighted Keep children away Children must never be allowed in the work area Do not let them handle machines tools or extension cords Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically nonconductive clothes and nonskid footwear are recommended when working Wear restrictive hair covering to contain long hair SKU 45333 Page 2 8 Use eye and ear protection Always wear ANSI approved impact safety goggles 9 Donotoverreach Keep proper footing and balance at all times Do not reach over or across electrical cables or frames 10 Maintain tools with care Inspect tool cords periodically and if damaged have them repaired by an authorized technician 11 Use the right tool for the job Do not attempt to force a small Coolant Pump or attachment to do the work of a larger industrial Coolant Pump There are certain applications for which this product was designed Do not modify this Coolant Pump and do not use this tool for a purpose for which it was not intended 12 Stay alert Watch what you are doing use common sense Do not operate any Coolant Pump when you are tired 13 Check fo2. CENTRAL MACHINERY 2 GALLON COOLANT PUMP Model 45333 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com Copyright 2001 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement paris please call 1 800 444 3353 Revised Cover Page 09 04 Specifications Capacity 2 Gallons Electrical 110V 60 Hz 4 amps Filter ID Filter Hose Length Features magnetic Flex Hose Base Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference Safety Warnings and Precautions WARNING When using tool basic safety precautions should always be fol lowed to reduce the risk of personal injury and damage to equipment Read all instructions before using this product l 2 Avoid working alone If an accident happens an assistant can bring help Avoid electrical shock Prevent body contact with grounded surfaces such as pipes radiators ranges and cabinet enclosures when testing voltages
3. could result in personal injury Maintenance Make sure the pump is not plugged in when servicing the unit 1 When the coolant tank is empty remove the Pump Base 12 and clean off any built up residue or debris from the bottom of the Tank 1 2 Periodically remove the Filter 6 and clean it remove any trapped metal filings 3 Occasionally disconnect the Flex Hose Base 7 and check for built up residue Clean if necessary Parts List c Filter E e mese o M oo Sapi PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts SKU 45333 Page 5 Assembly Drawing SKU 45333 Page 6
4. ex Nuts 5 3 Connect the Hose 8 to the Adaptor 10 by slipping a Hose Clamp 11 over the Hose 8 and then slide the Hose 8 onto the barbed end of the Adapior 10 Tighten with Hose Clamp 11 4 Attach the Adaptor 10 to the Pump Base 12 by sliding it on pressure fit 5 Before snapping on the Cover 2 insert the other end of the hose through the smallest hole on the cover and secure it to the barbed end of the Flex Hose Base 7 with a Hose Clamp 11 6 Snap the entire Cover 2 unit back onto the Tank 1 Set the Filter 6 into the remaining hole on the Cover 2 Warning Position the electrical cord and plug so that it is not in contact with coolant or wet surfaces Operation 1 Make sure the magnetic Flex Hose Base 7 is near your workpiece and the magnetic base is secure to the metal table you are working on The tip of the Hose 8 on the Flex Hose Base 7 should be almost contacting the workpiece SKU 45333 Page 4 REV 09 03 Operation continued 2 Make sure the lever on the Flex Hose Base 7 is off perpendicular to the hose Fill the Tank 1 with coolant through the Filter 6 3 If your worktable has a groove around it to recycle the coolant run the hose not provided from the table into the Filter 6 4 Turn the lever on the Flex Hose Base 7 parallel to the hose and plug in the pump to begin flow Caution Recycled coolant will become very hot contact with hot coolant
5. r damaged parts Before using any Coolant Pump any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Do not use the tool if lever does not turn On and Off properly 14 Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this Coolant Pump Approved accessories are available from Harbor Freight Tools 15 Do not operate Coolant Pump if under the influence of alcohol or drugs Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the Coolant Pump 16 Use proper size and type extension cord If an extension cord is required it must be of the proper size and type to supply the correct current to the tool without heating up Otherwise the extension cord could melt and catch fire or cause electrical damage to the tool This tool requires use of an extension cord of 0 to 10 amps capability up to 50 feet with wire size rated at 18 AWG Longer extension cords require larger size wire If you are using the tool outdoor
6. s use an extension cord rated for outdoor use signified by WA on the jacket 17 Maintenance For your safety maintenance should be performed regularly by a qualified technician SKU 45333 Page 3 Note Performance of this tool if powered by line voltage may vary depending on variations in local line voltage Extension cord usage may also affect tool perfor mance Warning The warnings cautions and instructions discussed in this instruc tion manual cannot cover all possible conditions and situations that may oc cur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Unpacking When unpacking check to make sure parts listed on page 5 are included If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual Assembly Refer to the Assembly Drawing on page 6 1 Unsnap both of the Snap Rings 9 and remove the Cover 2 2 Insert the Pump 3 through the hole in the Cover 2 making sure the gasket is centered on the brim of the Pump 3 and snug between the Pump 3 and the top of the Cover 2 Put the matching metal brim provided on the bottom of the Pump 3 and snug it up to the bottom of the Cover 2 Line up the holes of the brim of the Pump 3 the Cover 2 the gasket and provided metal brim Secure through the top with 3 Pan Screws 4 and H
Download Pdf Manuals
Related Search