Harbor Freight Tools 6_Color Product manual
Contents
1. z lt z ui zZ Ei z Item 69861 For technical questions please call 1 800 444 3353 Page 13 ADNVNALNIVIN Page 14 NOTICE Clean the Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush Cleaning ACAUTION TO PREVENT INJURY Needles are very sharp Use extreme caution when handling needles Solvent Selection Follow the paint manufacturer s recommendations for cleaning solvent type and disposing of used solvent WARNING TO PREVENT FIRE IF AFLAMMABLE SOLVENT NEEDS TO BE USED ADHERE TO THE FOLLOWING a Follow solvent manufacturer s clean up instructions and safety precautions b Flush Airbrush a full hose length from air compressor c If collecting flushed solvents in metal container transfer to nonmetal container and flush metal container d Work far away from any ignition sources in a vapor free area e Keep class ABC fire extinguisher nearby After each use 1 Empty the Jar and clean it with the solvent 2 Fill the Jar with solvent and spray it through the Airbrush into a container Once the Jar is empty repeat the process until the solvent comes out clean 1 Disconnect from the air source 2 After disconnecting point the Airbrush into the spent solvent container and depress the Trigger again to make sure no air remains 3 Remove the Nozzle and Needle and soak them in solvent until clean Use old toothbrush and to2. Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush General Operation IMPORTANT Proper spraying technique is ESSENTIAL to achieve good results 1 Press down on the Trigger to release air from the Nozzle Slowly and gently draw back on the Trigger to release paint from the Needle The air will atomize the paint and create a fine spray 2 Continue to move the Trigger back slowly to achieve the consistency you need for your spray technique 3 Once you have achieved the desired consistency you may fix the position using the Adjustment Screw Note If the Air Cap becomes clogged a Increase the Air Pressure to force out the clog b If the above does not work remove the Handle and move the Needle Chucking Guide 13 back and forth 4 Keep the distance from the workpiece at about 3 to 5 depending on the flow adjustment and the paint 5 For very fine detail work you may decrease the distance up to 1 from the workpiece Note The size of your spray pattern will differ based on the distance between the work surface and the Airbrush The closer the Airbrush is the finer the pattern will be 6 To avoid paint build up start moving the Airbrush before pressing the Trigger When finished with the stroke release the Trigger while still moving the Airbrush Doing this will produce a smoother finish Do not stop moving the Airbrush while spraying If the Airbr
3. OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Ww 5 z lt FA w zZ Ei z Item 69861 For technical questions please call 1 800 444 3353 Page 17 SONVNALNIVIN NOTICE Clean the Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush Parts Lists and Diagram Airbrush Parts List and Assembly Diagram Part Description Qty Part Description Qty 1 Protective Cap 6 17 Needle Spring 6 2 Aircap 1 6 18 Needle d 6 3 Nozze 6 19 ORng 1 p 6 4 j ArCapBoy 1 6 20 ValveRod J 6 5 jJoRng 1 0 6 21 ORng 32 S 6 6 Packing 1 1 6 22 Spin 6 7 Packing Nut 6 29 Valve Screw 6 8 Body 25 6 24 VaveBoy 6 9 Adjustment Screw 6 25
4. direct spray at people or animals 8 Attach all accessories properly to the tool before connecting the air supply A loose accessory may detach or break during operation 2 Do not exceed maximum air pressure 3 Do not spray near open flames pilot lights stoves heaters the air compressor or 9 Install an in line shutoff valve any other heat source Most solvents and to allow immediate control over coatings are highly flammable particularly the air supply in an emergency when sprayed Maintain a distance of at least even if a hose is ruptured 25 feet from the air compressor If possible locate the air compressor in a separate room 10 Air hose fittings may get hot during use Allow fittings to cool before disconnecting 4 Read all of the information concerning coating products and cleaning solvents 11 WARNING Some dust created by power Do not use chlorinated solvents sanding sawing grinding drilling and e g 1 1 1 trichloroethylene and other construction activities contains dichloromethane also known as chemicals known to the State of California methylene chloride to clean airbrushes to cause cancer birth defects or other Many airbrushes contain aluminum reproductive harm which reacts strongly to chlorinated Some examples of these chemicals are solvents Contact the solvent or coating Lead from lead based paints manufacturer as needed regarding Crystalline silica from bricks and cement or potential chemica
5. extra length to allow free movement while working Airbrush Setup and Adjustment AWARNING TO PREVENT SERIOUS INJURY Do not adjust or tamper with any control or component in a way not specifically explained within this manual Improper adjustment can result in tool failure or other serious hazards zZ O co Lu a fo CAUTION Keep hands away from Trigger while making adjustments IMPORTANT Only used paints 5 Gently push the Fitting on the Lid into designed for use with an Airbrush the Color Stem on the Airbrush Note Proper paint mixture is essential Note The Jar is held in place Follow the manufacturer s directions Most paints with friction not threading will spray easily if they are thinned properly did i i pope 6 Start the air compressor and set 1 Thin the paint according to manufacturer s the regulator to needed pressure directions and mix thoroughly Do not exceed maximum air pressure 2 Carefully strain the paint Note To avoid clogging start with the lowest through a paint strainer pressure increasing pressure if needed 3 Fill the Jar to no more than 3 4 full 7 Testthe consistency by spraying Thread the Lid onto the Jar on a piece of scrap material 4 Thread the Air Hose onto the Note Adjust the Air Pressure Valve s Airbrush s Air Inlet to regulate spray consistency Item 69861 For technical questions please call 1 800 444 3353 Page 11 e D m 5 a O z NOTICE Clean the
6. throttle and or turn the switch to its off position before leaving the work area Service a Tool service must be performed only by qualified repair personnel b When servicing a tool use only identical replacement parts Use only authorized parts Item 69861 For technical questions please call 1 800 444 3353 Do not overreach Keep proper footing and balance at all times Proper footing and balance enables better control of the tool in unexpected situations Use safety equipment Wear heavy duty work gloves and e a NIOSH approved respirator during use Non skid safety shoes and a hard hat must be used for the applicable conditions Always wear eye protection Wear ANSI approved safety goggles Store the tool when it is idle out of reach of children and other untrained persons A tool is dangerous in the hands of untrained users Check for misalignment or binding of moving parts breakage of parts and any other condition that affects the tool s operation If damaged have the tool serviced before using Many accidents are caused by poorly maintained tools There is a risk of bursting if the tool is damaged Use only accessories that are identified by the manufacturer for the specific tool model Use of an accessory not intended for use with the specific tool model increases the risk of injury to persons Use only lubricants supplied with the tool or specified by the manufacturer Page 3 H
7. 5 o 3 S 3 o E S amp S o a sjueuoduioo jeuondgo Joo1 Je Moe Burun euy 04 eAreA Bunsnfpy sv 4 soaldyiom Bulbewep wor JodeA Jayem sjue eJg 19 ug jeues 5 av 2 oseo a1 pue uonoeuuoo xoinb sepi oJg Bnid pue jejdnoD 3 100 0 eunsseid je sjsnipy J ejnb y a 8991 J0M Jo 00 Dulbewep woy uonesuepuoo pue HIP siue ed dH a joorormesipeuucp esoH av V dn s Ajddns sry ajqeyiodg 9 ainbi4 Page 9 3353 444 800 please call 1 For technical questions Item 69861 Clean the Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush sjuguodwiod JeuondQ JOO ye Moje Bulun aul JO4 soled Bunsnfpy sv O UOneuluJe uoo eJnjsioul S UBABIq 1I9iq 1euee o Jv N 001 01 11 sj2euuo5 son EH esn jo jurod oj se sBuug uui z L eur any uoueug 9 ejpjejdnoo seseeju esoHJepeel IW UJO S S WOJ 9Jh SIOUJ UIP OL ane eg d aseajal pue seui YOURIG o 1e sejnquisig uiu g e eur aiv ure 3 uonoeuuoo xoinb sepi oJd bnlg pue Jejonoo E uononpaJ uoneJqiA 104 esoH uonejosi a uogeouqnijo0 4e JO4 ojeougni y 100 0 eanss sd ae sysnlpy oenb i r 9ueu zulew JO ulejs s jo suonoes sejelos 9 EA lleg B uoneuluejuoo m eoel d ul JosseJduioo Jie seanoes syog Jououv g uonesuepuoo pue HIP sjueAeJd Mls Uononpei UOHeIGIA pue esiou 104 sped uo
8. For technical questions please call 1 800 444 3353 Page 7 dnlas NOTICE Clean the Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush Air Supply Setup AWARNING TO PREVENT SERIOUS INJURY FROM EXPLOSION Use only clean dry regulated compressed air to power this tool Do not use oxygen carbon dioxide combustible gases or any other bottled gas as a power source for this tool 1 Incorporate a filter regulator with pressure gauge in line shutoff valve and quick coupler for best service as shown on Figure C on page 9 and Figure D on page 10 An in line shutoff ball valve is an important safety device because it controls the air supply even if the air hose is ruptured The shutoff valve should be a ball valve because it can be closed quickly Note Do not use an automatic oiler system or add oil to airline The oil will contaminate the material being propelled ruining the final result 2 Attach an air hose to the compressor s air outlet Connect the air hose to the air inlet of the tool Other components such as a coupler plug and quick coupler will make operation more efficient but are not required A waRNING TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION Do not install a female quick coupler on the tool Such a coupler contains an air valve that will allow the air tool to retain pressure and operate accidentally after the air supply is di
9. HoseConnectrNu 6 10 Trigger CT 6 26 O Ring for Hose Connect 6 11 Rocker 1 6 27 Hose Connector 6 Needle Adjusting Sleeve Needle Chucking Guide Valve Screw 30 MetalHangr Needle Chucking Nut Glass Jar Assembly 6 Needle Cover Handle Page 18 For technical questions please call 1 800 444 3353 Item 69861 NOTICE Clean the Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush Airbrush Holder Parts List and Assembly Diagram Part Description Qty 94 Airbrush Holder 6 Item 69861 Qty Ri NEN 7 Adjustment Screw 1 Part Description 54 55 nlet Outlet Connectors Suction Cup 3 AirHose 7 54 Adapter 1 4 18 NPT 55 Case 1 3 7 1 For technical questions please call 1 800 444 3353 Page 19 MAINTENANCE Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repair
10. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference CENTRALPNEUMATIC professional 6 color airbrush kit with holder Clean the Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush Visit our website at http www harborfreight com ITEM 69861 Email our technical support at tech harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken please call 1 800 444 3353 as soon as possible AWARN ING Copyright 2012 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included ALaAVS NOTICE Clean the A
11. W LL lt 2 ALaAVS NOTICE Clean the Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush Air Source a Never connect to an air source b Never use oxygen carbon dioxide that is capable of exceeding combustible gases or any bottled 85 psi Over pressurizing the tool gas as an air source for the tool may cause bursting abnormal Such gases are capable of explosion operation breakage of the tool or and serious injury to persons serious injury to persons Use only clean dry regulated compressed air at the rated pressure or within the rated pressure range as marked on the tool Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air pressure range Ay SAVE THESE INSTRUCTIONS Symbol Definitions Symbol Property or Statement l Property or Statement WARNING marking Pounds per square inch of pressure concerning Risk of Eye Injury Wear ANSI approved eye protection CFM Cubic Feet per Minute flow WARNING marking concerning 4 Risk of Respiratory Injury Wear NIOSH approved respirator at standard conditions WARNING marking concerning Risk of Explosion LEN Page 4 For technical questions please call 1 800 444 3353 Item 69861 NOTICE Clean the Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush Specific Safety Instructions 1 Do not
12. bystanders children and Cluttered benches and dark areas visitors away while operating the tool increase the risks of electric shock Distractions are able to result in fire and injury to persons the loss of control of the tool Page 2 For technical questions please call 1 800 444 3353 Item 69861 NOTICE Clean the Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush Personal Safety a Stay alert Watch what you are doing and use common sense when operating the tool Do not use the tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating the tool increases the risk of injury to persons b Dress properly Do not wear loose clothing or jewelry Contain long hair Keep hair clothing and gloves away from moving parts Loose clothes jewelry or long hair increases the risk of injury to persons as a result of being caught in moving parts Tool Use and Care a Do not force the tool Use the correct tool for the application The correct tool will do the job better and safer at the rate for which the tool is designed b Disconnect the tool from the air source before making any adjustments changing accessories or storing the tool Such preventive safety measures reduce the risk of starting the tool unintentionally Turn off and detach the air supply safely discharge any residual air pressure and release the
13. irbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush Table of Contents Safety cni d tedio Me tus 2 Maintenance eod es 13 SPECIHICALONS oec reete 5 Parts Lists and Diagram 18 Warranty cte cts tente dbcns 20 CENTRALPNEUMATIC WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death Indicates a hazardous situation which if not avoided A DANGER will result in death or serious injury Indicates a hazardous situation which if not avoided AWARNING could result in death or serious injury Indicates a hazardous situation which if not avoided ACAUTION could result in minor or moderate injury NOTICE Addresses practices not related to personal injury CAUTION IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator WARNING When using tools basic precautions should always be followed including the following Work Area a Keep the work area clean and well lighted b Keep
14. l reactions other masonry products Arsenic and chromium from 5 Industrial applications must chemically treated lumber follow OSHA requirements Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed 6 Spraying hazardous materials may result in serious injury or death Do not spray pesticide acid corrosive material fertilizer or toxic chemicals 7 Paints and solvents may be harmful or fatal if to filter out microscopic particles swallowed or inhaled Avoid prolonged skin California Health amp Safety Code contact with solvents or paints as they will 8 25249 5 et seq irritate skin After any contact immediately WARNING The brass components of wash off exposed area with hot soapy water this product contain lead a chemical known to the State of California to cause birth defects or other reproductive harm California Health amp Safety Code 25249 5 et seq Specifications 15 50 PSI Spray Pattern Hairline to 1 1 2 Wide Air Inlet 1 8 28 NPS 3 4 oz 22cc 4 CFM 50 PSI Item 69861 For technical questions please call 1 800 444 3353 Page 5 H W LL Ed 2 dnlas Functions Page 6 NOTICE Clean the Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanen
15. lace Needle Will Not Spray 1 No pressure at Airbrush 1 Check air hoses 2 Air Pressure Valve not open enough 2 Open Air Pressure Valve Overspray 1 Improper application speed 1 Move moderately and parallel Paint drifting 2 Improper distance from workpiece 2 Adjust distance to unintended objects Nozzle Leakage 1 Dirty Nozzle 1 Clean Nozzle 2 Worn or damaged Nozzle 2 Replace Nozzle and or Needle Air Leaking 1 Dirty air valve seat 1 Clean air valve seat from Nozzle 3 Too much air pressure 3 Reduce air pressure 2 Sticking air valve 2 Lubricate air valve seat 3 Damaged air valve spring 3 Replace air valve spring 4 Worn damaged air valve seat 4 Replace air valve Follow all safety precautions whenever diagnosing or servicing the tool Disconnect air supply before service Page 16 For technical questions please call 1 800 444 3353 Item 69861 NOTICE Clean the Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND
16. neJgiA v pajeouqn uoN N 4 1 E 1 at Dm paa lur utr mes S En H 5 f S OOL 9 pejye uqn1 i z M m c edois i Uoo dn s Ajddng sry Aeuones q oinbi4 SETUP Item 69861 3353 444 800 please call 1 For technical questions Page 10 NOTICE Clean the Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Inspect tool before use looking for damaged loose and missing parts If any problems are found do not use tool until repaired Workpiece and Work Area Set Up 1 Designate a work area that is clean 3 Before spraying mask nearby and well lit The work area must not objects not being sprayed and lay allow access by children or pets to cloths not included on the floors prevent distraction and injury 4 Prepare the workpiece according to 2 Route the air hose along a safe paint manufacturer s directions path to reach the work area without creating a tripping hazard or exposing the air hose to possible damage The air hose must be long enough to reach the work area with enough
17. othpicks to remove any paint CAUTION Do not immerse Airbrush Note Do not use metal objects to clean the Nozzle to prevent damage to the passages 4 Inspect Needle If it is bent have it replaced by a qualified technician 5 Use appropriate solvent to wipe down Airbrush body 6 Lubricate Airbrush after cleaning A non silicon oil or a light lubricant may be used on threaded connections before storing Solution Disposal After cleaning dispose of cleaning solution according to the solution manufacturer s directions and local hazardous waste standards For technical questions please call 1 800 444 3353 Item 69861 NOTICE Clean the Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush Air Supply Maintenance Every day perform maintenance on the air supply according to the component manufacturers instructions Storage Store in a dry secure area out of reach of children ul 5 z lt z w Z lt Item 69861 For technical questions please call 1 800 444 3353 Page 15 ADNVNALNIVIN NOTICE Clean the Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush General Troubleshooting Chart Possible Causes Likely Solutions Poor Paint 1 Low paint level 1 Refill Atomization 2 Paint not properly thinned 2 Thin paint 3 Clogged Nozzle 3 Clean Nozzle 4 Loose damaged Needle 4 Adjust or rep
18. s or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state CENTRALPNEUMATIC 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353
19. sconnected Note Air flow and therefore tool performance can be hindered by undersized air supply components Page 8 3 For technical questions please call 1 800 444 3353 The air hose must be long enough to reach the work area with enough extra length to allow free movement while working Close the in line shutoff valve between the compressor and the tool Turn on the air compressor according to the manufacturer s directions and allow it to build up pressure until it cycles off Adjust the air compressor s output regulator so that the air output is enough to properly power the tool but the output will not exceed the tool s maximum air pressure at any time Adjust the pressure gradually while checking the air output gauge to set the right pressure range Inspect the air connections for leaks Repair any leaks found If the tool will not be used at this time turn off and detach the air supply and safely discharge any residual air pressure to prevent accidental operation Note Residual air pressure should not be present after the tool is disconnected from the air supply However it is a good safety measure to attempt to discharge the tool in a safe fashion after disconnecting to ensure that the tool is disconnected and unpowered Item 69861 NOTICE Clean the Airbrush IMMEDIATELY after use D 5 a E lt o 5 D 2 o 2 o c S E o 2 z o Iz G gs o o 2 5
20. tly clog the Airbrush Adjustment Trigger Screw Nozzle Not Visible J Air Inlet Lid Fitting Airbrush Holder Air Hose Inlet Outlet Air Pressure Connector Valve Figure A For technical questions please call 1 800 444 3353 Item 69861 NOTICE Clean the Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush Initial Set Up Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this A manual including all text under subheadings therein before set up or use of this product Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagram near the end of this manual Before Setup 1 This air tool may be shipped with 3 The Metal Hanger 30 can be attached to a protective plugs covering the air inlets secure surface and used to hang the Airbrush Remove these plugs before set up for drying or when it is not being used 2 The Metal Cup 28 may be used for excess correctly thinned paint and also for solvent when it is time to clean the Airbrush Airbrush Holder Setup 1 Thread Air Hoses 52 onto the Inlet Outlet Connectors 43 2 Designate one Air Hose for the Air Supply Inlet Use the Adapter 54 to make the connection from the Air Hose to the Air Supply if necessary See Figure B Figure B Note Each connection has its own Air Pressure Valve Item 69861
21. ush stops even briefly while spraying the paint can build up and run down the workpiece CAUTION Air hose fittings may get hot Allow fittings to cool before disconnecting or wear gloves to prevent burns 7 Clean Airbrush es and Jar s thoroughly immediately after EVERY use according to instructions on the following pages Page 12 For technical questions please call 1 800 444 3353 Item 69861 NOTICE Clean the Airbrush IMMEDIATELY after use Delayed or inadequate cleaning will permanently clog the Airbrush Maintenance Instructions Procedures not specifically explained in this manual must be performed only by a qualified technician AWARNING TO PREVENT SERIOUS INJURY Detach the air supply and safely discharge any residual air pressure in the tool before performing any inspection maintenance or cleaning procedures TO PREVENT SERIOUS INJURY FROM TOOL FAILURE Do not use damaged equipment If abnormal noise vibration or leaking air occurs have the problem corrected before further use Inspection Note These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the air operated tool BEFORE EACH USE inspect the general condition of the tool Check for loose screws damaged air supply hose misalignment or binding of moving parts cracked or broken parts and clogged nozzle any other condition that may affect its safe operation wi 5
Download Pdf Manuals
Related Search