Harbor Freight Tools 16 In. Laser Level with Swivel Head Product manual
Contents
1. lowered by lifting the latch on the body of the Tripod and sliding the leg in or out to the desired height Push the latch down into place to Lock the Leg in place Repeat for the remaining two legs Set the Tripod on a flat surface Once the Tripod 15 is set up you can raise and lower the Rotating Head 7 by turning the Handle 18 located at the top of the Tripod See Figure 2 below Rotating Head 7 Handle 18 Tripod 15 Figure 2 Page 4 5 Wind the Handle clockwise to raise the Rotating Head and counterclockwise to lower the Rotating Head 6 Set the Plastic Body 5 into the slot in the Tripod See Figure 3 below Tighten the Knob 14 on the top of the Tripod to secure the Plastic Body in place Tripod slot Figure 3 OPERATING INSTRUCTIONS Read the ENTIRE IMPORTANT A SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Initial Leveling AWARNING TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION Turn Power Switch to Off before adjusting Level 1 Turn the three Adjusting Knobs 16 one at a time to level the Rotating Head 7 See Figure 4 below Vertical Bubble 3 Horizontal Bubble 4 gt AAA Adjusting Knobs 16 Figure 4 For technical questions please call 1 800 444 3353 SKU 69259 2 Keep turning the Adjusting Knobs 16 until the Bul2. 7 Keep work area clean and well lit 8 This product is not a toy Keep it out of reach of children SKU 69259 10 11 12 13 14 15 Keep children and bystanders away while operating Laser Level Inspect before every use do not use if parts loose or damaged Stay alert watch what you are doing and use common sense when operating Laser Level Do not use Laser Level while you are tired or under the influence of drugs alcohol or medication Dress properly Do not wear loose clothing or jewelry Keep your hair clothing and gloves away from moving parts Maintain labels and nameplates on the tool These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement WARNING This product contains or when used produces a chemical known to the State of California to cause cancer and birth defects or other reproductive harm California Health amp Safety Code 25249 5 et seq The warnings precautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SAVE THESE INSTRUCTIONS REV 10k SPECIFICATIONS ae Max Tripod Height 42 AAA noted LASER LIGHT AVOID DIRECT EYEEXPOSURE Max Output lt 5 mW
3. Wavelength 650 10 nm CLASS LASER PRODUCT This product complies with 21 CFR 1040 10 and 1040 11 Diode Mfr Sean amp Stephen Corp 4F NO3 Lane 335 Sec 4 Hsin Yi Rd Taipen China Manufacture Date UNPACKING When unpacking make sure that the item is intact and undamaged If any parts are missing or broken please call Harbor Freight Tools at 1 800 444 3353 as soon as possible INSTRUCTIONS FOR PUTTING INTO USE Read the ENTIRE IMPORTANT A SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product AWARNING TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION Turn the Power Switch to Off before adjusting Laser Level Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagram near the end of this manual SKU 69259 For technical questions please call 1 800 444 3353 Page 3 Latch Assembly Your Laser Level will require some assembly prior to use Read entire manual to become familiar with product BEFORE you use the Laser Level Be sure you have all parts described in the Parts List and Assembly Diagram located on the last page of this manual Unfold Tripod 15 by pulling out on the Tripod arms Turn the Knob 17 to lock the arms in place See Figure 1 below Tripod 15 Arms Figure 1 3 legs of the Tripod can be raised
4. THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO PARTS LIST AND ASSEMBLY DIAGRAM Part Description Qty 1 LaserAperture ___ 1 2 BackCover 1 3 Vertical Bubbe _ _ _ 1 4 Horizontal Bubble __5 Plastic Body 1 _ 6 LevelModules _ 1 7 RotatingHead _ _ S 1 _8 Battery Spring 1 _ 9 OnOff Button 1 10 jFrontCover 11 14 16 Record Product s Serial Number Here Note Note and are not available individually as replacement parts SKU 69259 For technical questions please call 1 800 444 3353 __ ___ Qty 11 11 12 Fantens 11 13 Battery Cover 1 14 Knob 1 15 Tripod 8 16 AdjustingKnob 13 17 Knob 18 Handle 11 19 BullsEye Bubble 2 ROt f 100100 S AAA AAA gt EEE EEE 8 5 3 ATA 6 310 320 330 12 7 If product has no serial number record month and year of purchase instead Some parts are listed and show
5. PITTSBURGH 16 LASER LEVEL WITH 360 ROTATING HEAD SET UP AND OPERATING INSTRUCTIONS Visit our website at http www harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2011 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included For technical questions or replacement parts please call 1 800 444 3353 SAVE THIS MANUAL Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference IMPORTANT SAFETY INFORMATION In this manual on the labeling and all other information provided with this product This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or de
6. ath DANGER DANGER indicates a hazardous situation which if not avoided will result in death or serious injury AWARNING WARNING indicates a hazardous situation which if not avoided could result in death or serious injury ACAUTION CAUTION used with the safety alert symbol indicates a hazardous situation which if not avoided could result in minor or moderate injury Page 2 For technical questions please call 1 800 444 3353 NOTICE is used to address practices not related to personal injury CAUTION CAUTION without the safety alert symbol is used to address practices not related to personal injury General Safety Warnings WARNING Read all safety warnings and instructions Save all warnings and instructions for future reference Laser Light Avoid A DANGER direct eye exposure 1 Do not direct the laser beam into the eyes of any person or animal Doing so may cause severe injury to the eye 2 Verify Laser Level is in the position before making any adjustments or changing the batteries 3 Position batteries in proper polarity and do not install batteries of different types charge levels or capacities together 4 Remove batteries if Laser Level is not to be used for a long period of time 5 The Laser Level is a delicate instrument do not drop or jar the Laser Level 6 Wear ANSI approved safety goggles and heavy duty work gloves during use
7. e a Installing and Removing Batteries Remove the Battery Cover 13 located under the On Off Button 9 4 See Figure 7 below Battery Cover __ 13 4 1 2 Figure 7 For technical questions please call 1 800 444 3353 The Laser Level uses two 2 AAA batteries Remove the old batteries and insert two new batteries See Figure 8 below AAA Batteries Figure 8 WARNING Verify batteries are inserted according to indicated polarity so that positive and negative ends match the diagram on the end of the Laser Level Replace the Battery Cover 13 To prevent accidents turn off the tool and disconnect its power supply after use Cleaning Maintenance and Lubrication BEFORE EACH USE inspect the general condition Laser Level Check for loose hardware misalignment or binding of moving parts cracked or broken parts and any other condition that may affect its safe operation AFTER USE wipe external surfaces of the tool with clean cloth Store the Laser Level indoors and out of children s reach SKU 69259 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF
8. ls Eye Bubbles 19 float exactly in the center of the circle See Figure 5 below Bubbles 19 Figure 5 3 NOTE The Bulls Eye Bubbles 19 are intended for initial leveling of the Rotating Head 7 only After placing the Plastic Body 5 into the tripod slot further leveling should be done using the Horizontal Bubble 4 as a reference See Figure 4 on preceding page General Operating Instructions 1 Designate a work area that is clean and well lit The work area must not allow access by children or pets to prevent distraction and injury NOTE The numbers indicated in Figures and 6b are for reference only The Laser Level knobs are not numbered 2 Set the level parallel to knobs 1 and 2 as shown in Figure below Adjust knobs 1 and 2 until the Horizontal Bubble 4 is in the center 3 Top View Figure 6a 3 Turn the level 90 It should now be over knob as shown in Figure 6b below Top View Figure 6b Adjust knob 3 until the Horizontal Bubble 4 is again in the center Turn Level back 90 to the position as shown in Figure 6b The Horizontal Bubble 4 should still be in the center If it is not repeat the steps above If after repeated attempts the Level is still uneven check all mountings to ensure nothing is loose and that the Plastic Body 5 is properly seated in tripod slot Once Laser Level is set in Tripod you may set
9. n for illustration purposes only Page LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We
10. the laser to the type of beam you wish to use The laser projects up to 1 500 feet Set the Lens Fixture 11 Down and this mode will fix the Level Laser beam to a beam splitter mode The beam splitter mode will project a horizontal line Set the Lens Fixture 11 to the top mode and this mode will set the Laser Level beam to a dot Turn the Laser Level ON by pressing the ON OFF button 9 WARNING Do not point the Laser Level at people or animals Once you have leveled the Level Laser in the Tripod 15 you can use it for many applications Rotating the Rotating Head 7 with the laser ON and set to the beam splitter mode you can set a line of equal height in a room to verify alignment of pictures electrical plugs or shelving The Laser Level can also be used to set a level for any surface while providing a bright beam to mark your settings by SKU 69259 For technical questions please call 1 800 444 3353 Page 5 MAINTENANCE AND 2 SERVICING Procedures not specifically explained in this manual must be performed only by a qualified technician TO PREVENT AWARNING SERIOUS INJURY 1 Page 6 FROM ACCIDENTAL OPERATION Turn the OFF the Laser Level before performing any inspection maintenance or cleaning procedures TO PREVENT SERIOUS INJURY FROM TOOL FAILURE Do not use damaged equipment If abnormal noise or vibration occurs have the problem corrected before further us
11. will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd Box 6009 Camarillo 93011 800 444 3353 Page 8 For technical questions please call 1 800 444 3353 SKU 69259
Download Pdf Manuals
Related Search